Search Documents

By Howard C. Dunkle

Various factors can affect the quality of B1112 and B1113 steel as produced in a bessemer plant; among them: vessel-charging practice, blowing practice, ingot-pouring practice, ingot delivery-time practice, pit-heating practices, and ingot-rolling practice. Evaluation of the influence of ingot delivery time on quality has been chosen as the subject for this paper because this time is completely within the control of the operator, and on this particular factor there is a tremendous amount of information in the dusty archives of the average steel plant. In order to know how much improvement can be made and when attention should be directed to other factors that influence quality, in the continual struggle for improvement, the effect of ingot delivery time must be accurately evaluated. Once this is done, the importance of other variables can be accurately obtained, thus eliminating the necessity of resorting to opinions that are of doubtful value at best. In the study described herein, extensive use was made of the statistical card system as a method of determining the effect of ingot delivery time as a quality factor in bessemer screw-stock grades by simple direct correlation. The value of this statistical method as a means of accurately determining the influence of various factors has been amply demonstrated by Work1 for the bessemer process and by Hand and Gould2 and Fetters and Chipman3 for the open-hearth process. The quality records of 300,000 tons of bessemer screw-stock billets were used in this study of the effect of ingot delivery time on the rejections for breaks, pipe, check and seams. The reduction in the number of rejections for poor quality reduces the costs and increases the productivity per man-hour. The operator today, more than ever before, must know how to keep costs down, how to do it most quickly and in the best way, and how to obtain the highest quality in line with the ever increasing demands of the customer. It is necessary for him to know the individual relations and interrelations between various factors affecting the quality of the manufactured product if he is to produce material that will meet competitively the cost, performance, and quality demands of the trade. SIGNIFICANCE OF STEEL MANGANESE, MIXER SILICON AND STEEL SULPHUR AS QUALITY FACTORS In order to obtain the highest grade of material it is necessary to control many factors-not just one or two, as operators

Jan 1, 1945

By Howard C. Dunkle

Various factors can affect the quality of BIII2 and BIII3 steel as produced in a bessemer plant; among them: vessel-charging practice, blowing practice, ingot-pouring practice, ingot delivery-time practice, pit-heating practices, and ingot-rolling practice. Evaluation of the influence of ingot delivery time on quality has been chosen as the subject for this paper because this time is completely within the control of the operator, and on this particular factor there is a tremendous amount of information in the dusty archives of the average steel plant. In order to know how much improvement can be made and when attention should be directed to other factors that influence quality, in the continual struggle for improvement, the effect of ingot delivery time must be accurately evaluated. Once this is done, the importance of other variables can be accurately obtained, thus eliminating the necessity of resorting to opinions that are of doubtful value at best. In the study described herein, extensive use was made of the statistical card system as a method of determining the effect of ingot delivery time as a quality factor in bessemer screw-stock grades by simple direct correlation. The value of this statistical method as a means of accurately determining the influence of various factors has been amply demonstrated by Work1 for the bessemer process and by Hand and Gould2 and Fetters and Chipman3 for the open-hearth process. The quality records of 300,000 tons of bessemer screw-stock billets were used in this study of the effect of ingot delivery time on the rejections for breaks, pipe, check and seams. The reduction in the number of rejections for poor quality reduces the costs and increases the productivity per man-hour. The operator today, more than ever before, must know how to keep costs down, how to do it most quickly and in the best way, and how to obtain the highest quality in line with the ever increasing demands of the customer. It is necessary for him to know the individual relations and interrelations between various factors affecting the quality of the manufactured product if he is to produce material that will meet competitively the cost, performance, and quality demands of the trade. Significance of Steel Manganese, Mixer Silicon and Steel Sulphur as Quality Factors In order to obtain the highest grade of material it is necessary to control many factors—not just one or two, as operators

Jan 1, 1945

By R. A. Vandermeer, Paul Gordon

On the basis of a unified concept, theoretical erPressions for grain boundary migration in recrys-tallization are derzved for impurity-controlled and impurity-independent migration. The expression in the former case is analogous to that Previously derived by Lucke and Detert, and in the latter is shown to be equivalent to that usually obtained on the basis of absolute reaction rate theory. The equations are tested with quantitative experimental data for boundary migration obtained for the recrystallization of poly crystalline zone-refined alumimnz and for binary "alloys" of this aluminum with 0.00021, 0.00043, 0.0017, 0.0034, 0.0068, 0.0124, and 0.0256 at. pct Cu, respectively. All the essential characteristics of the e@erimentally determined boundary migration rates check both qualitatively ard quantitatively with the predictions of the theoretical equations. THE rates of transformations are customarily analyzed phenomenologically in terms of the two component rates—N, the rate of nucleation and, G, the rate of growth of the nuclei. The scientific aim of both theory and experiment is to describe the fundamental atomic phemmena involved in these two component processes with the hope that parameters calculated from theoretical equations will check those found experimentally. In solid state transformations, the theoretical and experimental problems are both generally of almost prohibitive complexity, for in addition to changes in composition and in such properties as density which may accompany transformations in amorphous, nonrigid materials, transformations in crystalline substances also involve structural changes, crystal reorientations, and the development of stresses. In studying such transformations it thus becomes; highly desirable, if not essential, to focus on a transformation and a set of conditions which minimize the number of active variables. This principle has been applied with considerable success by Cohen and his associates' in their evaluation of nucleation theories using the martensite transformation as the basis of study. A similar possibility exists for the evaluation of growth theories by the use of recrystallization after cold-deforming. If an unalloyed metal is employed as the subject of investigation, the recrystallization transformation involves basically only a change in strain-conditions and orientations. In spite of this possible simplilfication, however, until recently little quantitative success has attended attempts to correlate recrystal1ization parameters measured experimentally with those calculated theoretically. It seems highly probable that this lack of success may be attributed, both in the experimental and theoretical treatments, to one or more of the following factors: a) conditions have usually been studied under which apparently* both nucleation and growth are active;

Jan 1, 1962

By I. R. Kramer, P. D. Gorsuch, D. L. Newhouse

Although many methods have been suggested for the calculation of tensile strength and yield point from chemical composition, their usefulness has been limited to a particular cooling rate or section size. Further limitations have been imposed by failure to take into account many of the alloying elements that exert a considerable influence on the tensile strength or yield point. These systems, nevertheless, have filled an important need in many instances. The value of a system for the calculation of the tensile properties from the chemical composition and cooling rate is that it permits the prediction of the effect of alloying elements and heat-treatment on the mechanical properties, so that more efficient use of alloying elements may be made. Furthermore, it aids in the choice of steel for a given application aid tends to decrease the number of steels that otherwise would have to be tested. It is the purpose of this work to present a method of calculating tensile strength and yield point from the chemical composition and to suggest a method of correlating the tensile-strength and yield-point factors and cooling rate. Steelmakers have been interested for many years in the calculation of the tensile strength of hot-rolled steels. Quest and Washburn' summarize several of the attempts that have been made to devise formulas. They show the inadequacy of each of these formulas and present one of their own. It is apparent from their work that a simple additive equation of the type TS = A + BX + Cy + DZ + . . . , where A, B, C, D, etc. are experimentally determined constants and x, y, z, etc., are the percentages of alloying elements present in the steel, is not adequate to analyze fully the situation encountered in the calculation of tensile strength. For example, it was found that the difference between the calculated and observed values became progressively greater as the carbon and manganese contents were increased. Therefore, the effect of manganese was given as a function of the carbon content. Grossmann, in his work on the harden-ability of quenched steels, and Walter, in his method of calculation of tensile strength of normalized steels, present two cases in which multiplying factors were successfully used to express the combined effect of alloying elements. The factors in both cases were obtained from the fractional increase in hardenability or tensile strength with increase of alloy content. Yield point often is more important in design than tensile strength. For quenched and tempered steels a linear correlation exists between yield 2nd tensile strength.4 This is not true, however, for normalized

Jan 1, 1948

By P. D. Gorsuch, I. R. Kramer, D. L. Newhouse

Although many methods have been suggested for the calculation of tensile strength and yield point from chemical composition, their usefulness has been limited to a particular cooling rate or section size. Further limitations have been imposed by failure to take into account many of the alloying elements that exert a considerable influence on the tensile strength or yield point. These systems, nevertheless, have filled an important need in many instances. The value of a system for the calculation of the tensile properties from the chemical composition and cooling rate is that it permits the prediction of the effect of alloying elements and heat-treatment on the mechanical properties, so that more efficient use of alloying elements may be made. Furthermore, it aids in the choice of steel for a given application aid tends to decrease the number of steels that otherwise would have to be tested. It is the purpose of this work to present a method of calculating tensile strength and yield point from the chemical composition and to suggest a method of correlating the tensile-strength and yield-point factors and cooling rate. Steelmakers have been interested for many years in the calculation of the tensile strength of hot-rolled steels. Quest and Washburn' summarize several of the attempts that have been made to devise formulas. They show the inadequacy of each of these formulas and present one of their own. It is apparent from their work that a simple additive equation of the type TS = A + BX + Cy + DZ + . . . , where A, B, C, D, etc. are experimentally determined constants and x, y, z, etc., are the percentages of alloying elements present in the steel, is not adequate to analyze fully the situation encountered in the calculation of tensile strength. For example, it was found that the difference between the calculated and observed values became progressively greater as the carbon and manganese contents were increased. Therefore, the effect of manganese was given as a function of the carbon content. Grossmann, in his work on the harden-ability of quenched steels, and Walter, in his method of calculation of tensile strength of normalized steels, present two cases in which multiplying factors were successfully used to express the combined effect of alloying elements. The factors in both cases were obtained from the fractional increase in hardenability or tensile strength with increase of alloy content. Yield point often is more important in design than tensile strength. For quenched and tempered steels a linear correlation exists between yield 2nd tensile strength.4 This is not true, however, for normalized

Jan 1, 1948

By P. D. Gorsuch, D. L. Newhouse, Irvin R. Kramer

ALTHOUGH many methods have been suggested for the calculation of tensile strength and yield point from chemical composition, their usefulness has been limited to a particular cooling rate or section size. Further limitations have been imposed by failure to take into account many of the alloying elements that exert a considerable influence on the tensile strength or yield point. These systems, nevertheless, have filled an important need in many instances. The value of a system for the calculation of the tensile properties from the chemical composition and cooling rate is that it permits the prediction of the effect of alloying elements and heat-treatment on the mechanical, properties, so that more efficient use of alloying elements may be made. Furthermore, it aids in the choice of steel for a given application and tends to decrease the number of steels that otherwise would have to be tested. It is the purpose of this work to present a method of calculating tensile strength and yield point from the chemical composition and to suggest a method of correlating the tensile-strength and yield-point factors and cooling rate. Steelmakers have been interested for many years in the calculation of the tensile strength of hot-rolled steels. Quest and Washburn' summarize several of the attempts that have been made to devise formulas. They show the inadequacy of each of these formulas and present one of their own. It is apparent from their work that a simple additive equation of the type TS = A + BX + Cy + DZ + ? ? ? , where A, B, C, D, etc. are experimentally determined constants and x, y, z, etc., are the percentages of alloying elements present in the steel, is not adequate to analyze fully the situation encountered in the calculation of tensile strength. For example, it was found that the difference between the calculated and observed values became progressively greater as the carbon and manganese contents were increased. Therefore, the effect of manganese was given as a function of the carbon content. Grossmann,2 in his work on the hardenability of quenched steels, and Walters,3 in his method of calculation of tensile strength of normalized steels, present two cases in which multiplying factors were successfully used to express the combined effect of alloying elements. The factors in both cases were obtained from the fractional increase in hardenability or tensile strength with increase of alloy content. Yield point often is more important in design than tensile strength. For quenched and tempered steels a linear correlation exists between yield and tensile strength .4 This is not true, however, for normalized

Jan 1, 1946

By Laurence Delisle, Aaron Finger

THE alloys formed by the addition of nickel to iron by convelltional metallurgical procedures show physical properties that differ widely from those of the individual metals. The effect of alloying on the mechanical properties is most pronounced in alloys containing between 15 and 25 per cent nickel. The tensile strength of an alloy containing, for example, 20 per cent nickel and 80 per cent iron (with 0.06 per cent carbon), in an annealed condition, is above 150,000 lb. per sq. in.? owing to a martensitic type of transformation, as compared with about 50,000 lb. per sq. in. for pure iron in the same condition. The object of this work was to determine whether the same beneficial alloying effect could be obtained in alloys of iron and nickel prepared by powder metallurgy technique. PROCEDURE Bars and pellets for tension and compression tests, respectively, were made. Two groups of specimens were prepared: (I) by cold-pressing the powders and sintering; (2) by cold-pressing the powders, sintering, repressing and resintering. Raw Materials Nickel powder supplied by Metals Disintegrating co., marked MD-151, was used. A typical analysis of this powder was as follows: sulphur, 0.040 per cent; copper, 0.18; iron, 0.23; manganese, 0.002; magnesium, 0.001 5 ; lead, 0.035; tin, 0.025 ; silicon, 0.08; chromium, 0.008. Electrolytic iron powder supplied by Plastic Metals Inc. was used. A representative chemical analysis for impurities other than gases, supplied by the vendor, gave the following results: carbon, 0.005 per cent; manganese, 0.002; silicon, 0.003; phosphorus, 0.001; sulphur, 0.004; nickel, 0.008. The fractions from these powders passing a 3 2 5-mesh sieve were reduced in hydrogen at 600°C. for one hour, to clean the surfaces of the particles. The reduced powders, slightly caked, were ground in a mortar and screened again through a 325- mesh sieve. Mixing The proper proportions of the powders were mixed overnight on rolls, in glass jars fitted with iron-wire baffles to break aggregates of particles that might form. Pressing All specimens were compacted on hydraulic presses. The pellets were compacted in a cylindrical die, ½ in. diameter. The ratio of thickness to the diameter of the pellets was maintained as nearly as possible at 0.9, as specifed for standard short compression pieces. The tensile bars were made by compacting 30 grams of powder. Their shape is shown in Fig. I. The compacting pressures for the pellets and the tensile bars were:

Jan 1, 1946

By Pol Duwez, Spencer R. Baen

A LTHOUGH the practical importance of Fe-Cr--iV Mo alloys has long been recognized, constitution studies have been limited to a few alloys within rather narrow ranges of composition. The purpose of the present study was to establish the phase boundaries in the ternary diagram at a temperature of 1200°F (650°C).* The identification of phases and the determination of phase boundaries were based primarily on X-ray diffraction measurements and occasionally on microscopic observation. The methods used for locating the phase boundaries were essentially those described in detail by Andersen and Jette,' and by others.', The compositions of 180 alloys, prepared by powder metallurgy techniques, are shown in Fig. 1. The chemical analysis and mesh size of the powders which were used for the preparation of the alloys are given in Table I. The powders were mixed for 48 hr or longer, then compacted under 80,000 psi in a %-in. diam steel die. Each specimen weighed approximately 5 g. The compacts were sintered for 4 hr at 2500°F (1371°C) in an atmosphere of pure dry hydrogen (dew point near the temperature of liquid nitrogen). An open tray of chromium powder was placed upstream of the compacts to act as a "getter" for the last traces of oxygen or water vapor. In many cases this chromium powder was bright after sintering. Occasionally the upstream side of the powder was slightly greenish, but in all cases the downstream side was metallic. Some of the alloys contracted during sintering and some expanded as much as 20 pct. The latter alloys, which in all cases were brittle, were crushed in a tool steel mortar, repressed, and resintered for 4 hr at 2500°F. After sintering, the alloys were aged for ten days at 1200°F (650°C) in evacuated (105 mm Hg or better) fused silica tubes and were cooled rapidly to room temperature following the aging treatment. The use of the powder metallurgy technique in preparing alloys for structural investigation offers a simple method 'of avoiding contamination or non-homogeniety which could result from a melting operation. It is very often possible to dispense with chemical analysis of the alloys which have been prepared by the powder metallurgy method. In lieu of chemical analysis, it is necessary to determine the weight of the compact before and after sintering. The chemical composition of the alloy may be considered as that of the green compact, within the limits of accuracy determined by the loss of weight during sintering. In phase-diagram studies it is important to achieve homogeniety in structure, whether the alloys are prepared by powder metallurgy or by melting. Homogeniety means complete diffusion during the sintering of the alloys which are prepared by powder metallurgy. It has been found from experience that the best criterion for establishing the completeness of diffusion is the sharpness of the X-ray diffraction patterns. This criterion has been used throughout the present study. The X-ray diffraction data were obtained using powder cameras of either 214.86 or 71.62 mm diam. Copper, cobalt, or chromium Ka. radiation was used, the choice being based on the alloy composition. The powder samples were obtained by filing or crushing, depending on whether the alloy was ductile or brittle. In some cases, the powder was annealed for 4 to 6 hr at 1200°F in vacuum. The measurements were corrected for film shrinkage and absorption. The large camera, in which the film is mounted

Jan 1, 1952

By J. E. Flinn, S. A. Duran

The steady-state creep behavior of poly crystalline cad mi inn was studied over a temperature range of (1.56 to 0.94 Tm. Two distinct mechanisms were found to occur over this temperature range. They were described by: where and represerqt the minimum strain rates corresponding to the low- and high-temperature regions, respectirely. The two regions of constant acti11ation energy were connected by a transition region where the strain rate was controlled by both mechanisms acting in parallel. At temperatures below a transition temperature of about 0.7 Tm the agreement between the activation energy value for creep and that for self-diffiision suggests a rate-controlling mechanism of dislocation climb. For cadwzium, steady-state creep at temperatures above 0. 7 Tm appears to be controlled by another mechanism, perhaps involving the behavior of dislocation jogs. FRENKEL et al.1 studied the high-temperature creep of polycrystalline cadmium and reported an activation energy of 21 kcal per mole for the 0.5 Tm < T < 0.8 Tm range. Based on observations of creep rate at only two temperatures, a value of 22.1 kcal per mole was determined by Medbury. These two investigations were for the purpose of showing agreement between the activation energy for creep and that for self-diffusion, reported3 as 18.2 and 19.1 kcal per mole, respectively, for diffusion parallel and perpendicular to the hexagonal axis. Gilman4 investigated prismatic glide in single crystals of cadmium over a higher-temperature range of 0.72 to 0.93 Tm, and found an activation energy of 29 kcal per mole. He also reported5 an activation energy higher than that of self-diffusion for prismatic glide in zinc single crystals deformed at temperatures near the melting point. This value was in good agreement with those found for an equivalent temperature range by Flinn and Munson6 and by Tegart and sherby7 for polycrystalline zinc. These two independent studies also disclosed at lower temperatures another value of activation energy near that for self-diffusion. It would be expected from the creep results on zinc and single-crystal cadmium that creep studies on polycrystalline cadmium, extended to temperatures near the melting point, might yield an activation-energy value higher than the 22 kcal per mole value found in earlier studies. The purpose of this paper is to report the steady-creep behavior of polycrystalline cadmium over a temperature range of approximately 0.5 to 0.9 Tm EXPERIMENTAL METHOD The cadmium used in this study was obtained in the form of as-cast rods, 0.5 in. diam, through the courtesy of the Bunker Hill Mining Co. The material was of 99.995 pct purity, as determined by spectro-chemical analysis. The creep specimens, which were 0.250 in. diam by 0.400 in. long and annealed at 300°C for 45 min to produce a stable average grain diameter 0.25 mm, were tested in compression using an apparatus similar to that described by Sherby.8 The specimen temperature was controlled to within ±0.5°C with the help of appropriate constant-temperature baths. The applied stress was maintained within 1.0 pct of the desired value by the additions of lead shot at fixed strain increments. No barreling was observed over the strains encountered during testing. Isothermal creep tests9 were used in the study with only a few differential temperature tests10 run for comparison purposes. Steady-state creep data were obtained over a temperature range of 60 to 287°C (0.56 to 0.94 Tm) at five stress levels ranging from 28.1 to 140.6 kg per sq cm. RESULTS The minimum or steady-state creep rate may be described by an equation of the following form:" where i is the minimum strain rate, S is the structure factor, F is a stress function, Qc is the energy of activation, T is the absolute temperature, and R is the gas constant. The minimum strain rates obtained in this study for cadmium were recorded on a semilogarithm plot as a function of the reciprocal absolute temperatures for the various stress levels, as shown in Fig. 1. This figure shows a characteristic transitional behavior" with a parallel interaction of two mechanisms. It is obvious that the activation energies corresponding to the individual processes are insensitive to stress because the curves are parallel. The discrete activation-energies values for the low- and high-temperature regions for the various stress levels are reported in Table I, and were determined by the least-mean-square method. For the low-temperature region, an activation energy of 20.7 ± 0.6 kcal per mole was obtained, and for the

Jan 1, 1967

Two career employees of the US Dept, of the Interior, in a recent study, indicated that by the end of 1974, 73% of all public lands had been entirely or partially closed to exploration and development of essential resources for leasable minerals and 67% had been similarly restricted for locatable minerals.1 This has come about because of the lack of coordination within the executive branch and between the executive and legislative branches of the federal government and without regard for the cumulative, depressing effect on future domestic mineral production. Much of the withdrawn land is felt to have great potential for discovery of significant mineral deposits.

Jan 5, 1976

By G. H. Jardine

In future years, decision makers in the coal industry will make more and more decisions based on information from computer-based models. Whilst the use of such techniques will provide many advantages for coal companies, particularly in terms of efficient utilisation of their human resources, it is equally important for the decision makers to have an awareness of the limitations inherent in each particular computer-based model being used to provide information for the decision making process. A recommended procedure for identifying such limitations - by analysing the 3 major elements of the model - is presented. The human aspects of increased use of computer-based techniques are emphasised throughout the paper.

Jan 1, 1983

By J. T. Norton, A. L. Mowry

S. J. SINDEBAND*—(1) Discussing the properties of the powders used, Mr. Rostoker mentioned a silicon powder as being between 150 and 325 mesh. We always had much difficulty in measuring particle size of silicon powder by screen analysis, because of its tendency to agglomerate. I would be interested in the method used to measure these particle sizes. (2) Mr. Rostoker maintains that the measurement of magnetic properties is more accurate in determining complete homogenization of an alloy, than is the X ray diffraction technique. I wonder whether this is really true. Even when diffusion is complete, magnetic properties will change during continuation of the heat treatment, due to change in density and pore shapes, as has been demonstrated by Mr. Rostoker himself. Which effect is faster, the diffusion of the alloy components or the attainment of final density, will, in my opinion, depend very much on initial material and sintering conditions used. For magnetic applications, of course, the magnetic measurements are most suited for determining the point at which equilibrium conditions are reached. (3) I was glad to see that Mr. Rostoker had used sample sizes which are similar to those I had used previously, and I believe that ring samples of about 2 in. od will become more or less standard samples for the determination of magnetic properties of powder metallurgy products. I should like to ask how the density was changed for the samples on which the effect of porosity was investi- gated, and, further, why the sintering temperature used for this series of experiments was so low. It is somewhat surprising that a 24-hr treatment at 850°C acts so much more to spheroidize the pores than a treatment for 1 hr at 1100°C. But the effect seems to be indisputable. I have made an investigation of the influence of sintering temperature for longer times on the maximum permeabilities of iron powder compacts which was presented at the International Powder Metallurgy Conference in Graz, in 1948, and I hope that these results will be published here within a short time. The results of this investigation are confirmed by Mr. Rostoker&apos;s findings that the change of time from 1 to 24 hr changes the permeability behavior considerably in the direction as indicated by Polder and Van Santen for spheroidiza-tion of pores. I do not quite understand Mr. Rostoker&apos;s explanation of the influ-

Jan 1, 1950

By J. H. Frye, J. L. Scott, J. W. Woods

THERE are at least two effects of temperature on the stress required to produce plastic flow. 1) Metals plastically strained for the same amount at different temperatures possess different stress-strain curves and different internal structures (e.g., nature and density of imperfections). 2) There is both experimental and theoretical evidence that the stress necessary to produce plastic flow may vary with temperature even though the internal structure remains constant.1-5 Much of the data in the literature is difficult to interpret because these two effects are simultaneously present. In the work reported here, they are considered separately. Standard 0.505 in. tensile specimens were prepared from high-purity Mond nickel and OFHC copper. Nickel specimens were annealed in hydrogen at 1150°C for 30 min and furnace cooled. This produced an average grain diameter of 1.4 mm. Copper specimens were annealed in vacuum at 525°C for 6 hr and furnace cooled. This produced an average grain diameter of 0.11 mm. Nickel tensile specimens were prestrained in tension at 500°K, whereas copper tensile specimens were prestrained in tension at room temperature. All specimens were cooled to 74°K and heated to room temperature. After these treatments all of the tensile specimens of a given set possessed identical structures. All specimens were returned to the tensile machine and tested at various temperatures and constant cross-head speed. Many of the tensile curves showed well defined yields but, in order to minimize personal judgment, the yield was always chosen as the stress corresponding to 0.2 pct plastic deformation. Results are summarized in the graph of yield vs temperature of test, Fig. 1. All of the specimens corresponding to any one line have had identical treatments and, therefore, have identical internal structures. Thus, each line gives the relation between yield stress and temperature for one constant internal structure. The lowest line, which is for annealed nickel, shows no measurable variation of yield with temperature. This is similar to Blewitt&apos;s6 results on copper single crystals, but a variation in yield with temperature was found by Andrade and Henderson&apos; in single crystals of nickel, and by Car-recker and Hibbard8 in annealed polycrystalline copper. The three other lines, which are for prestrained materials, show that there is a linear relation between yield stress and temperature when the internal structure remains constant. Such a relation might be expected from a rate equation such as that of Kauzmannl on the assump- tion that the activation energy is either independent of or linear with temperature. These results would also be expected if the shear moduli of copper and nickel are linear functions of temperature for, as Cottrell and Stokes have pointed out," in all dislocation theories of strength the flow stress appears proportional to the shear modulus of the material. In copper and nickel, since the modulus of elasticity decreases roughly linearly with increase in temperature," it is probable that the modulus of shear also decreases approximately linearly with increasing temperature. A detailed discussion of the effect of these and other factors on the temperature dependence of flow stress in face-centered-cubic metals has recently been given by Seeger.4

Jan 1, 1958

By E. H. Edwards, J. Washburn

Zinc crystals were deformed in simple shear and it was found that anisotropic strain hardening occurred in which the inactive slip systems were hardened more than the active system. The formation of dislocation barriers by dislocation interaction was discussed as a possible explanation of the hardening of the latent systems. STRAIN hardening which accompanies slip in a metal crystal is not limited to the slip systems actively contributing to the plastic strain. There is also a strengthening of the latent slip systems which are crystallographically equivalent to the active system. In the case of aluminum deformed in tension, Taylor and Elam1 found that plastic flow on one set of octahedral planes caused either the same or a slightly greater hardening on an inactive set. Similar results have been obtained for crystals of a brass2 and of Cu-A1 solid solutions.3 Experiments by Rohm and Kochendorfer4 indicated that the hardening of the active system exceeded the hardening of any latent system for aluminum crystals deformed in shear. On the other hand, strain hardening in zinc and cadmium crystals tested in simple shear at —196°C was recently found to be greater in the latent than in the active slip direction." When the strain direction was shifted during testing to a direction 60" from the original, a higher stress was required for glide to continue than would have been needed for flow to proceed in the original direction. The relation between the hardening of active and latent systems must be complex, depending upon the relative orientations of the systems and upon the experimental techniques used to deform the crystal. A detailed knowledge of the hardening produced in latent systems would be valuable in choosing between possible dislocation models of the strain-hardening process. The experimental data now available are incomplete and even contradictory. The present study was undertaken to provide quantitative information regarding the relative amount of hardening of active and latent systems for a particularly simple case. Zinc crystals were deformed in simple shear along one of the three crystallographically equivalent directions [250], [1210], and [1120] in the slip plane, and the relative hardening produced in each of these directions was compared. Experimental Procedure and Results The single crystals of 99.99 pct purity zinc used in this investigation were grown from the melt in the form of 1 in. diam spheres. Shear specimens were acid-machined from the crystals by a method which has been described previously. The gage section of the test specimen was a cylinder having a height of 1/8 in. and a cross-sectional area of approximately 1/3 sq in. All specimens were machined with the axis of this cylindrical gage section aligned with the [0001] axis of the crystal. An innovation in the design of the shearing apparatus for these tests was the provision for a rapid shift in the direction of the applied stress from one slip direction to any other slip direction lying in the same slip plane. Fig. 1 shows a section through the specimen and shearing apparatus, and Fig. 2 is a

Jan 1, 1955

By H. L. Talbot, A. J. Hall, R. S. Young

A method for the chemical differentiation of oxidized cobalt from sulphide cobalt in complex mine and concentrator products is of considerable interest to a number of mining companies throughout the world. At Rhokana Corporation, in Northern Rhodesia, for instance, cobalt is found chiefly in the sulphide form, as carrollite, but a cobalt oxide mineral also occurs irregularly underground, and relatively small quantities in the mill feed from time to time are difficult to detect visually at the concentrator. The oxide cobalt is not amenable to the sulphide flotation process used at Rhokana and nearly all of it passes into the tailing. The occasional period when high tailing losses occur with no appreciable change in the cobalt content of the mill feed has naturally been disturbing to the concentrator staff, who had no means of determining whether an influx of cobalt oxide ore or laxity on the part of the mill flotation operators as responsible for these results. A procedure for determining oxidized copper minerals, based on their solubility in dilute sulphuric acid saturated with SO2, has been used for many years in the copper industry. In the presence of cuprite the procedure fails, but otherwise it gives results quite satisfactory for control pur- poses. Empirical methods for determining oxidized forms of zinc and lead have been proposed, but they are generally unsatisfactory except in isolated cases of a very simple ore. No published procedure for determining oxidized forms of cobalt or siinilar elements has come to the authors&apos;notice. Experimental Procedure There are obviously two alternatives in attacking a problem of this nature. One is to employ a solvent for oxide cobalt that will not dissolve cobalt sulphide. The other is to find a substance capable of oxidizing the cobalt sulphide to sulphate, which of course is water-soluble and can then be leached from the water-insoluble oxide cobalt. A representative sample of Rhokana cobalt oxide ore was secured, ground to minus 200-mesh, and carefully rolled to furnish a standard sample for this work. The analysis of this material gave the following percentages: Co, 0.55; Cu, 1.64; Fe, 2.98; S, 0.08; SiO2, 41.42; Al2o3, 11.20; CaO, 13.82; MgO, 3.80. As a source of cobalt sulphide a similar large sample of carrollite was prepared, analyzing Co, 23.36 per cent; Cu, 27.32; and S, 31.13. This sample of course was not pure carrollite, but was the best obtainable in quantities sufficient for a standard intended for considerable work. It was a pure sulphide sample, microscopic examination showing only carrollite, a little bornite, and gangue, with no visible sign of oxidized ore present. A wide variety of reagents as used in an effort to selectively dissolve oxide cobalt or to oxidize sulphide cobalt to

Jan 1, 1949

By R. S. Pratt

IT is proposed to discuss the materials and furnaces, as well as the melting procedures used in preparing metal for casting billets, bars or cakes for mill fabrication. As far as possible, consideration will be given to the alloys that are commonly made in most brass mills producing strip, tube, rod and wire. RAW MATERIAL The basic raw material for such mills, of course, is copper, which may be obtained in the form of ingots, ingot bars or cathodes. Refinery-cast ingots and ingot bars, which are simply double ingots, are supplied in accordance with A.S.T.M. Specifications as regular electrolytic or fire-refined tough-pitch copper. In the wrought-metal industry, the electrolytic brands have been preferred, although during the war large quantities of fire-refined coppers sufficiently pure to be suitable for all existing requirements were imported from South America. With the exception of Lake copper, most primary fire refined coppers produced in this country have not been considered satisfactory for wrought metal alloys. Cathode copper, which is now widely used instead of ingot copper for alloying, is the electrolytically deposited metal that is normally remelted in the production of electrolytic tough-pitch ingots. It is in the form of rough, flat plates not suitable for processing but quite satisfactory for melting when sheared into suitable sizes. Raw zinc is perhaps the next most important raw material and this is obtained in various grades, depending on the analytical requirements of the alloy to be made. The grades of zinc as outlined in the A.S.T.M. Specifications vary in cost with the amount of impurities-lead, iron, cadmium-and are purchased in such a way as to produce the most economical mixture consistent with the purity required in the alloy. Other virgin metals (lead, tin, aluminum and nickel) are used in varying quantities for making copper alloys. These elements can also be purchased in accordance with the appropriate A.S.T.M. Specifications where available. Also available are a number of special alloys, which are used as deoxidizers or as means of adding relatively small quantities of elements not suitable for adding directly as virgin metal. In this category are such materials as phosphor copper or phosphor tin, silicon copper, manganese copper, cadmium copper, and copper-iron or zinc-iron alloys. Some of these alloys may be purchased on a definite alloy basis or may be produced in the plant itself for its own use. For largely economic reasons, however, a great proportion of the charge to the melting furnaces consists of alloy scrap. In the production of many finished products, as much as 70 or 75 per cent of the metal originally cast may be discarded at various points along the production line. This material eventually finds its way back to the casting shop as mill scrap, overhaul or scalping chips, skeleton scrap, rod turnings, or miscellaneous fabricating scrap. One of the most serious problems in the

Jan 1, 1946

By Owen F. Jensen

CONSTRUCTION of a ground-water supply includes many operations, which do not end with completion of facilities. Evaluations must be made of the quality of water in various areas and the history of production. Following an analysis of geologic, hydrologic, and chemical data there must be an exploratory drilling program and a study of resulting information. When the well is completed a continuous survey of operating records and basic data is necessary, since designs for future wells are varied as more data becomes available for those already completed. As the following discussion must be limited to a single undertaking, the customary procedure will be outlined for development and construction of a ground-water supply in which more than three wells are involved. Parts of this procedure are applicable for all ground-water supplies. Three possible sites were selected for construction of a paper mill. The problem was that the industry daily required approximately 15 million gallons of water of the best quality available; however, if water of the best quality were not available in the desired amount, water of a poorer quality could be used up to half the required amount, about 7 million gallons. In the preliminary survey approximately 1500 to 2000 square miles were covered for each site. Collected data consisted of several hundred electric logs of oil and gas wells; reports by the U. S. Geological Survey on ground-water resources of localities in and near the area; unpublished records of several hundred water wells including chemical analyses of the water produced and drillers&apos; logs of the wells; records of periodic water-level measurements made in observation wells by the USGS; topographic maps drawn up by USGS and by army engineers; and highway and county road maps. A preliminary report based on study and evaluation of these data was presented to the client, recommending the site with the most favorable and economical ground-water conditions. The study indicated that water of the quality and quantity desired could be developed. In this particular area there were indications that the aquifer could be separated into two zones con- taining water of different chemical character. This chemical character varied somewhat with area, but principally with depth, a factor which later proved an economic advantage in design of the well field. After studying the preliminary report, the client weighed other economic factors as well as ground-water advantages and selected a plant site. Authority was given to proceed with detailed study of the chosen area. Evaluation of preliminary data concerning the area indicated that it should be supplemented with additional information derived from actual exploratory drilling and testing. A flexible plan of exploratory drilling was devised so that data obtained as each test hole was drilled could be correlated with existing data and additional test holes could be located and drilled accordingly. Specific data to be obtained from each test hole were: samples of all formations penetrated; the driller&apos;s descriptive log of formations; electric logging surveys; one or more samples of water from selected water-bearing formations; temperature; and water levels and their recovery after periods of production. The area studied in such detail was approximately 400 square miles. Choice of location for the original test holes was based on the preliminary study. The pattern for these test holes was designed to require a minimum number of holes and to allow for interpolation of data between two, three, and four holes. Geologic, hydrologic, and chemical data gathered after completion of the first four test holes showed that the north section was the most desirable in the area, which was then reduced from the original 400 square miles to about 150 square miles for more detailed and intensive study. On the basis of findings from the current test a tentative well field was laid out and a drilling program devised. One test hole was located on the actual plant site and later developed into a small pilot production well equipped with a deep well turbine pump. Water from this well was used for general construction requirements. Another test hole drilled near the pilot production well and adjacent to the proposed route of the well-collection system was used during the pumping test of the pilot production well to determine the degree of interference. From the data thus obtained, calculations were made to determine the coefficients of transmissibility and storage. Three additional holes

Jan 1, 1955

By Terkel Rosenqvist

J. Chipman (Massachusetts Institute of Technology, Cambridge, Mass.)—The fact that the experimental work has been applied to copper rather than iron and that the paper is presented to the Iron and Steel Division, I regard as rather significant. It shows the unity of metallurgy and the fallacy of trying to cut it up by metals. This result for the solubility of sulphur in molten copper correlates with Professor Schuhmann&apos;s finding that the published data on the other side of the copper-sulphur miscibility gap are also in error. I should like to ask the author to say a little bit more about the sulphur capacity of the slag. T. Rosenqvist (author&apos;s reply)-—I hope that Dr. Chipman will find the derivation of the expression for sulphur capacity more clearly explained in the printed version of the paper than in the oral discussion at the meeting. I feel that this quantity, which actually is the ratio of two activities, can be measured more easily than the individual activities. Even if the ratio CaO/CaS is chosen as the standard state, the expression can be used for any slag, even for slags completely free of lime, and it represents a way to put the desulphurizing power of all slag constituents into one bag. Some doubt has been expressed as to whether oxygen ions really exist in calcium oxide and in molten slags. From a thermodynamic view point that question is of minor importance. The term oxygen ion activity, or any activity for that matter, is defined rigorously by the equation: activity = exp p/RT, where p is the change in free energy connected with the transfer of one mol of ions from the standard state into the slag. Whatever happens to the ion in the slag is of no concern to the thermodynamicist. Regardless of whether the ion is "free" in the slag or not, or whether it is present in a very small amount, its activity can always be expressed, and for a thermo- dynamic calculation that is all we need. However, ionic activities will only be of some real value if they are simple functions of the slag composition, or can be measured easily. Concerning the real nature of the oxygen in the slag, my feeling is that the oxygen atom has a rather multiplex nature depending on how strongly it is tied by covalent forces or polarized by the other atoms or ions present. The oxides of iron, cobalt, and nickel differ from calcium oxide and blast furnace slags as to the amount of free electrons that can give rise to electronic conductivity. In slags we know that the conductivity is mostly ionic. The fact that reversible emf&apos;s can be obtained with oxygen electrodes in certain salt melts, indicates a significant amount of oxygen ions in these melts. But extended work, e.g. polaragraphic studies and measurements of transference number; are needed to obtain quantitative information about the real structure of the slags. D. E. Babcock (Republic Steel Corp., Youngstown, Ohio)—-With reference to the ion, it might be well to remember Dr. Moses Gomberg. All of his life he had no use for the ionization theory and he contributed greatly to the field of chemistry on the assumption there was no such thing as ions. I do not think we have to worry about whether the oxygen is ionic or not. I think one thing specifically should be brought to your attention and this I think is one of the important contributions of Dr. Rosenqvist. He pointed out what we know as oxygen potentials or what is described as oxygen potentials. I have used this concept for a long period of time and I want to state that if this concept is properly applied, it vitiates much of what we have in the literature, or makes our usual ideas regarding oxidation seem primitive. That one thing is more valuable than almost all the rest of the discussion as a fundamental basis on which to build a reasonable in-

Jan 1, 1952

By R. Bakish, C. S. Barnett

IN experiments on tantalum strained in tension, Bechtold did not observe deformation-twinning even at a temperature as low as that of liquid air.&apos; This is an unexpected behavior for a metal of body-centered-cubic structure. Therefore, it is desirable to determine whether the lack of twinning is an inherent characteristic of this particular metal, or whether the reluctance to twin can be overcome under suitable conditions. The following experiments were performed under conditions favorable to twinning and cleavage in their competition with slip, namely, with impact loading on large-grained sheet at low temperatures. The crystallography of cleavage in tantalum sheet was also investigated carefully because of the remarkable ductility of tantalum at low temperatures and because recent tests on oxygen-embrittled tantalum had disclosed unusual cleavage behavior for a metal of this structure: cleavage primarily on (110) planes and only occasionally on {100}.2 The tantalum, supplied by Fansteel, was of 99.9 pet purity, with the chief impurities being iron (0.03 pet) and carbon (0.03 pet). Coarse grains were produced by the strain-anneal method, the anneal being 4 hr at 2000°C in a vacuum of 10-3 mm Hg, followed by furnace cooling. Impact deformation was applied in various ways: a) by hammer blows on an anvil, the specimen and anvil being immersed in liquid nitrogen ( —196°C), b) by driving a precooled center-punch into the sheet, and c) by bending around a crystallographically determined axis with a hammer blow. The impact-deformation produced bands and slip lines on the surface, Fig. 1. The bands have every appearance of being deformation twins, a) They are tilted with respect to the untwinned surface. b) They have the appearance of Neumann bands in iron, thin lens shape, some having serrated edges. c) The orientation in each is different from that of the surrounding matrix and uniform within a given band, see slip lines within them in Fig. 1. d) Upon repolishing and etching, the difference in orientation and the resemblance to Neumann bands is again evident, Fig. 2. (In this micrograph the slight bend in the bands as they cross grain boundaries was noted frequently and results from the high degree of preferred orientation in the sheet.) e) The bands persist after annealing treatments that would have removed them had they been a low-temperature martensitic phase, e.g., after an anneal of 1/2 hr at 900°C. When back-reflection Laue data were plotted for single-surface analysis of several grains, every trace of the bands in each grain could be explained by (112) planes. In addition, two of the bands were located in space by traces on two surfaces, and these also were found to lie on (112) planes within the error of the stereographic plot. Since (1 12) is the anticipated composition plane for deformation twins in body-centered-cubic metals it is felt that the observations listed above are conclusive evidence for the identification of the bands as twins. Similar tests with impact at —77° and at 25°C produced no twinning. It is concluded that the critical shear stress for slip at the rates of straining used was always low enough to prevent the applied stress from reaching the value required for twinning at these temperatures. It was noted that the serrations along the edges of the twin bands exhibited parallel crystal facets. Several similarly oriented notches are visible in Fig. 1, and a remarkable set is shown in Fig. 3. It appears from Fig. 1 and similar areas that notches are frequently associated with the intersection of a slip line with a twin, although not all such intersections are at notches. In some instances a slip line appears to enter the twin, cross it, reflect from the opposite side and recross it, producing a pattern resembling a notch but without producing the notch itself, see Fig. 1. It is suggested that the stress concentration at the end of a slip line is responsible for these details. The strain energy associated with the pile-up of dislocations at a twin boundary may be lessened by untwin-ning or failing to twin a portion of the twin band, or

Jan 1, 1959

J. Chipman (Massachusetts Institute of Technology, Cambridge, Mass.)—The fact that the experimental work has been applied to copper rather than iron and that the paper is presented to the Iron and Steel Division, I regard as rather significant. It shows the unity of metallurgy and the fallacy of trying to cut it up by metals. This result for the solubility of sulphur in molten copper correlates with Professor Schuhmann&apos;s finding that the published data on the other side of the copper-sulphur miscibility gap are also in error. I should like to ask the author to say a little bit more about the sulphur capacity of the slag. T. Rosenqvist (author&apos;s reply)-—I hope that Dr. Chipman will find the derivation of the expression for sulphur capacity more clearly explained in the printed version of the paper than in the oral discussion at the meeting. I feel that this quantity, which actually is the ratio of two activities, can be measured more easily than the individual activities. Even if the ratio CaO/CaS is chosen as the standard state, the expression can be used for any slag, even for slags completely free of lime, and it represents a way to put the desulphurizing power of all slag constituents into one bag. Some doubt has been expressed as to whether oxygen ions really exist in calcium oxide and in molten slags. From a thermodynamic view point that question is of minor importance. The term oxygen ion activity, or any activity for that matter, is defined rigorously by the equation: activity = exp u/RT, where u is the change in free energy connected with the transfer of one mol of ions from the standard state into the slag. Whatever happens to the ion in the slag is of no concern to the thermodynamicist. Regardless of whether the ion is "free" in the slag or not, or whether it is present in a very small amount, its activity can always be expressed, and for a thermo- dynamic calculation that is all we need. However, ionic activities will only be of some real value if they are simple functions of the slag composition, or can be measured easily. Concerning the real nature of the oxygen in the slag, my feeling is that the oxygen atom has a rather multiplex nature depending on how strongly it is tied by covalent forces or polarized by the other atoms or ions present. The oxides of iron, cobalt, and nickel differ from calcium oxide and blast furnace slags as to the amount of free electrons that can give rise to electronic conductivity. In slags we know that the conductivity is mostly ionic. The fact that reversible emf&apos;s can be obtained with oxygen electrodes in certain salt melts, indicates a significant amount of oxygen ions in these melts. But extended work, e.g. polaragraphic studies and measurements of transference number; are needed to obtain quantitative information about the real structure of the slags. D. E. Babcock (Republic Steel Corp., Youngstown, Ohio)—-With reference to the ion, it might be well to remember Dr. Moses Gomberg. All of his life he had no use for the ionization theory and he contributed greatly to the field of chemistry on the assumption there was no such thing as ions. I do not think we have to worry about whether the oxygen is ionic or not. I think one thing specifically should be brought to your attention and this I think is one of the important contributions of Dr. Rosenqvist. He pointed out what we know as oxygen potentials or what is described as oxygen potentials. I have used this concept for a long period of time and I want to state that if this concept is properly applied, it vitiates much of what we have in the literature, or makes our usual ideas regarding oxidation seem primitive. That one thing is more valuable than almost all the rest of the discussion as a fundamental basis on which to build a reasonable in-

Jan 1, 1952