Search Documents

By Charles Legrand

(San Francisco Meeting, September, 1915) THE problem of mine pumping is so much affected by local conditions, and those conditions are so liable to changes during the life of a mine, that the best system to use is difficult to determine. The experience of the;, writer has been that, in general, for copper mines, electric pumping is most satisfactory unless the quantity of water to be pumped is great or. the mine does not use electric power for any other purpose. As a rule, however, figuring on the cost of necessary power plant, the total cost of: installation is greater with electric pumps than steam- pumps. As the water is liable to be gritty, outside-packed plunger pumps are to be recommended, and if the water is not acid, or only slightly so, chilled cast-iron plungers pay for their extra cost very quickly in diminished cost of packing. With chilled plungers it is possible to use metallic, packing instead of soft packing, if the water, is not too gritty nor the lift too high. In vertical pumps this packing is satisfactory for lifts up to 400 ft., in the experience of the writer; and may be found satisfactory for higher lifts. For water slightly acid, cement-lined pump bodies have given good satisfaction. For acid. water, both plungers and pump bodies should be made of acid-resisting bronze. For high lifts, especially with gritty water, a satisfactory pump valve is difficult to find. To reduce the unbalanced pressure on the valve at time of opening it is advisable to have narrow seats; this, however, brings high pressure on the seats when the valve is closed. On large valves for lifts of 600 to 1,000 ft. we have used leather, hard rubber, vulcanized fiber, and soft brass; for clear water the latter has given best satisfaction. The difficulties due to grit make it advisable to have large sumps where water can settle, and if possible, to have two of them so that they can be cleaned alternately. At the mines of the Old. Dominion Copper Mining ,& Smelting Co.; Globe, it was found that a small air. ejector discharging into a mine car is a very convenient way to clean mud and sand from a sump. .

Jan 9, 1915

By A. Karim, T. G. Langdon, C. Y. Cheng, J. E. Dorn

The effect of changes in temperature and stress on the creep behavior of Fe-4 pct Si was investigated over the temperature range from 650° to 1175K Over the temperature range of 799° to 110l°K, the shear strain rate, ?', obeys the relationship: where K is a constant, 7 the applied shear stress, G the shear modulus, g the free activation energy for diflusion, R the gas constant, and T the absolute temperature. The results strongly suggest that the creep in this alloy is controlled by a dislocation climb mechanism. In a recent investigation, Ishida, Cheng, and Dorn1 observed that the apparent activation energy for creep of a! Fe from 480" to 775°K corresponded to that for self-diffusion. Over the magnetic transformation range (775" to 1045"K), the apparent activation energy for creep increased steeply with increasing temperature in agreement with the known decrease in the free activation energy for self-diffusion. Passing through the Curie temperature, the apparent activation energy decreased abruptly following which it then increased mildly as the temperature further increased. Inasmuch as the apparent activation energy for creep of a! Fe below the Curie transformation range of temperatures appeared to decrease with increasing values of the stress, the data were analyzed in terms of a model based on the nonconservative motion of jogged screw dislocations. But since the observed creep rate was much higher than that which could be accounted for on the basis of usual models, the authors found it necessary to assume that pipe diffusion became significant over the lower temperature range. Furthermore, the abnormally high activation energy for creep above the Curie temperature was attributed to grain boundary migration which became prevalent in this temperature range. It was thought that a number of the interesting issues that arose in the creep of a Fe might be resolved by investigating the creep of Fe-4 pct Si alloy: This alloy has about the same Curie range and therefore should give creep results that closely parallel those for a Fe and in this way provide comparable data for analysis of creep mechanisms. Furthermore, it can be annealed at higher temperatures which could provide some stabilization against grain boundary migration. In addition, it might serve to illustrate the possible effects of short-range ordering on creep.

Jan 1, 1969

By Carl Altstetter, Roy Adams

Measurements of enthalpy changes and transformation temperatures me reported for the fcc -hcp marten-sitic transformation in pure cobalt single and multi-variant crystals andpolycrystalline specimens. From these measurements the free-energy difference between the two phases was calculated for both heating and cooling and for repeated cycles through the transformation. For heating of single crystals the average value of enthalpy change was 113 cal per mole but on cooling it was 84 cal per mole. This difference is interpreted in terms of lattice imperfections which are introduced during transformation. A calorimeter suitable for measurement of enthalpy changes of athertnal transformations is described. COBALT exhibits an allotropic phase transformation at around 417°C' where an hcp phase (a = 2.507, c = 4.0686, c/a = 1.6228)~ stable at low temperatures transforms to an fcc phase stable up to 1495°C. The transformation has a hysteresis of about 30°C— the exact magnitude of the hysteresis depending on the number of transformation cycles, grain size, impurity content, and prior treatment.'-6 The athermal character of the transformation and surface relief due to transformation shear indicate that the transformation is martensitic. Pole mechanisms for the transformation have been discussed by Sebilleau and Bibrin, Bilby, Seeger,' and Basinski and Christian. These authors have proposed that the cooling transformation is effected by rotation of a Shockley partial dislocation around a pole dislocation with a screw component of 2a/3(111). Such a rotation would change the stacking of close-packed planes from the abcabc fcc stacking to the ababab hcp stacking sequence. This mechanism would predict a lattice correspondence of {111}fcc~~(0002~cp, have been observed. One would expect the heating transformation to occur similarly, involving dislocation movements on the (0002)hcp. However, a high density of pole dislocations and high dislocation ve- locity are required to account for microscopic observations. Furthermore, the high back stress developed on the Shockley partial dislocation as it rotates toward the sessile dislocation associated with it makes it doubtful that this is in fact the transformation mechanism. A mechanism for spontaneous nucleation of partial dislocations1*l2 seems more reasonable. If a single crystal of cobalt is cycled through the transformation but never heated above 600°C, it will remain single."13 However, if the specimen is heated through the transformation and held for a short time at or above 1000°C before cooling, the cooling transformation usually involves all four {lll}fcc habits, resulting in neighboring orientations of hcp differing by 70.5 deg. This condition is termed multivariance and has been observed by Bibring and sebilleau5 and Nelson and ~ltstetter.' The latter authors used single crystals of cobalt grown in an electron beam zone refiner. They proposed that the strongly directional cooling caused the initial cooling transformation to occur on the {lll)fcc most nearly perpendicular to the temperature gradient. Transformation shear on one set of {lll}fcc planes immobilized dislocations on the other {lll}fcc planes involved in the initial transformation. Since there is only one (0002)hcp plane orientation, the product of subsequent heating transformations could have no more than two variants—the original fcc orientation or its twin. If, however, the specimen was annealed at a high temperature, such as 1000°C, there would be relaxation of dislocations into low-energy configurations, and in the absence of a sharp temperature gradient transformation on all four (111 Ifcc planes could occur. If a dislocation mechanism is responsible for the transformation, the perfection of the lattice should affect the reversibility of the transformation. Mutual constraints of neighboring grains in polycrystalline material would inhibit dislocation movement resulting in increasingly sluggish transformation. Indeed, Nelson and Altstetter found the M, to decrease and the A, to increase in going from single crystals to multi-variant specimens to polycrystals. The effect is enhanced by decreasing the grain size of a solid specimen or a powder.6'14 Data on the free-energy difference necessary to initiate the transformation gives information about the driving force of the transformation. This is an important consideration in the understanding of the transformation mechanism. The free-energy change associated with the transformation of the hcp phase to the fcc phase at some temperature T different from the equi-

Jan 1, 1969

By George Scott

MANY requests for information as to the possibility of washing coals to some predetermined percentage of ash or sulfur have suggested that the producers aim to satisfy some degree of purity set by the user of the fuel, rather than to attain the greatest economic benefit to all concerned. This paper is written to show that the highest economic purity of washed coal can be determined from washability studies of the raw coal, costs of mining and washing coal, and data on the effect of ash and sulfur on the value of the coal for the particular use for which it is intended.

Jan 1, 1929

By H. Ries

SPECIAL sands are those that are employed for special purposes. They have a limited use, as compared with sands for concrete and plaster. The sands discussed in this chapter are those used for foundry purposes, glass manufacture, filter beds, abrasive purposes, sandblasting, engine sand, sand for sheet asphalt, and furnace sand. These sands are almost invariably high in silica, consisting chiefly of quartz grains. In some-for instance, glass sands-freedom from ingredients other than silica, such as iron oxide, is important. Certain grades, like filter sand, require rather careful sizing, and in foundry sands the bond, usually clay, is important. One deposit may sometimes be used to supply several grades or types of sand by appropriate methods of screening and washing. The special sands discussed here are usually obtained from deposits of unconsolidated material but sands high in silica are derived occasionally from soft sand- stones that can be disintegrated easily. Requirements are not the same for all uses, and, while certain properties may be demanded, there are no officially adopted standard tests except for foundry sands. FOUNDRY SANDS Definition-Foundry sands include those siliceous sands that are used to make the forms for casting metals. If these are employed for making molds, they are known as molding sands; if for the cores that form the hollow spaces in the casting, they are called core sands. Naturally bonded sands are those containing a variable, though not usually large, amount of clay, which serves as a bond. Synthetic sands, now much used, represent an artificial mixture of sand with usually fire clay or bentonite. Core sands may be bonded with oil, cereal binders, resin, pitch, or other materials. The foundrymen apply the term "sharp sand" to one that is free from bond. Properties-The important properties to be tested at room temperature are texture or fineness, permeability, strength, deformation, and flowability. Those tested at elevated temperatures are compressive strength, expansion and contraction, sintering point, and durability. More attention probably has been given to research on the properties

Jan 1, 1949

LEAD and tin mixed together make an alloy through an attachment of natural affinity which they have with each other, so that when they are mixed it is difficult to recognize by the sight which one it is, if the essences of their qualities are not surpassed by more than half. If, indeed, one can be recognized, it is the tin which gives off a certain sharp odor to the sense of smell, besides having a greater hardness and whiteness. The best of these is the one that is the purest in its kind. In the alloy of tin it is the one that is the whitest and hardest, or, when it is bent or some thin end of it is held tightly by the teeth, is heard to crackle as frozen water does. Because this happens more with this than with other metals, I do not wish now to inquire into it. It is enough that it be a sign for recognizing when tin is pure or mixed. Pewterers say that it should be joined in alloy with lead and that it is better for working when it contains four or six pounds to the hundred because it makes it softer to the hammer and more fluid in casting. But I do not like to hear this, even if all they say is true, for I see that the tin that comes from England, when worked as well as in cakes that show it to be pure, is much more beautiful and better in all works than is that made in Venice. And I believe that it is not better for any work when mixed than when pure, except for the advantage of the master who, if he does nothing else, sells lead that is worth little for tin that is worth much. I find that when mixed it serves in only two things. One is when it is wished to make a solder for copper, for use when it is not worth while to solder the bottoms and large pieces of vessels with low-grade silver as should be done. The other is when master potters calcine it in order to make glazes and to apply white to their vases. I consider lead to be useless in all other works of any kind of metal, since it unites with none of the other metals of good company except tin.

Jan 1, 1942

By P. S. Rudman

Laves phases, AB2, are considered as Izerrzisub-stitutional solutions m1hich are defined by a one-for-truo replacement scheme. Atomic-size tnisfit is considered in terms of deviations of the ratio 2V°b/V°A from unity, where v° = atomic volume. A simple elastic model has been used to calculated deviations from "Vegard&apos;s law of atomic vol-umes". Comparison has been made between calculated and observed atomic-volume deviations fov 222 Laves phases. Agreement is generally very good although there ave some few exceptions which appear to be excusable in terms of electronic changes that ore beyond the scope of the present model. We can consider the formation of a binary sub-stitutional solution A-B from an A solvent as one-for-one replacements of A atoms by B atoms. As the atomic-size ratio deviates from unity, the solution becomes thermodynamically less stable and hence more restricted because of atomic-misfit strain energy. In accordance with our previously presented conclusion1 that the atomic volume, v, is in general the most appropriate measure of atomic size, the ideal size ratio for a binary sub-stitutional solution is vg/vA = 1. The Laves phases have been described by Berry and Raynor2 in terms of various stacking sequences of hexagonal layers of B atoms for the three structures MgZn2(C14), MgCu2(C15), and MgNi2(C36). To form the Laves phase of ideal composition AB, we start with complete hexagonal layers of B atoms in the appropriate stacking sequence and we remove, according to an appropriate scheme for each structure, two out of every four B atoms and replace the two removed atoms by one A atom. We thus might expect to find that the ideal size ratio for the Laves phases is 2v/B/ VA= 1. From this point of view, then, we call Laves phases hemi-substitutional solutions since we employ one-for-two replacements. By analogy with substitutional solutions we can expect for Laves phases that as the ratio 2VB/Va deviates from unity the phase occurrence will be more restricted. Laves3 has plotted the distribution of Laves phases as a function of the radius ratio, ?A/rB, and found that, while the distribution extended from 1.05 < rA/B < 1.50, the

Jan 1, 1965

By M. Metzger, J. Intrater

IN the large number of important studies on high-purity aluminum (e.g., recrystallization and grain growth, creep, internal friction), it does not seem to have been generally recognized that the iron content, despite its very low figure, has a strong influence on a number of properties. In part, its influence is due to the very low solubility of the Fe-A1 6 phase. For aluminum of about 99.99 pct purity, the iron content may be 0.001 to 0.004 pct. For values in this range, a second phase will be present below 410" to 480 °C. This was determined by extrapolation of a log solubility vs inverse temperature plot of the solid solubility data of Edgar.&apos; One consequence is the inhibition of grain coarsening below the solubility limit. This is shown in Table I, which gives, for three iron contents, the annealing temperature required for the absence of grains smaller than 1/2 mm average diameter together with the minimum temperature for the presence of some grains larger than 2 mm diameter. The specimens were 1/4x 1 1/2-in. strips cut from hard-rolled 1/16-in. sheet supplied by the Aluminum Co. of America.

Jan 1, 1954

By E. D. Leavitt

I desire to state briefly my views respecting the great practical value of the Watertown testing-machine, and the necessity that exists, for an able permanent commission to supervise its operations, in order that the results of all tests made thereon may be properly worked out and rendered available for public use. It is doubtless known to the Institute that this machine has, for the past two years, been placed at the service of the public upon payment of a per diem charge. It was my privilege to be among the first to use the testing-machine, and the results of my first experiments were of such importance, owing to the great capacity and extreme accuracy of the machine, that it has since become my practice to have tests of all materials used in constructions that came under my charge, made at Watertown. As a conseqnence, nearly one hundred tests have been made on my account directly, and some two hundred and forty additional for work built from my designs. It may be confidently affirmed, that the factor of anxiety on all these structures is exceedingly small .m far as the quality of material is concerned, and it is undoubtedly a very great advantage for parties interested in construction to have

Jan 1, 1882

By Charles S. Barrett, Hermann F. Kaiser, Robert F. Mehl

THE copper-silver system presents several points of special interest in the study of segregate structures. The system is simple eutectic, with limited solid solutions terminal with the pure component metals. The extent of solid solubility decreases with decreasing temperature for both the copper-rich and the silver-rich alloys, thus offering a possibility for the formation of Widmanstätten figures and also a possibility for aging after quenching. In contrast to the structures studied previously the structures in this system are unique in their origin, for one terminal solid solution will precipitate the other, and vice versa. In most of the other systems for which crystallographic data on the precipitation (or transformation) process are available, either intermetallic compounds or intermediate phases partake in the decomposition process; the absence of such phases thus distinguishes this system. The lattice structures of the two solid solutions are identical in type, differing in lattice spacing by approximately 10 per cent; because of this it seems difficult if not impossible to predict on the basis of present theory either the outward form of the precipitate or the lattice orientation relationships between matrix and precipitate. The eutectic temperature in the copper-silver system1 is 779° C. At this temperature copper dissolves 4.3 atomic per cent (7.0 weight per

Jan 1, 1935

By Ronald Gibala

THE Au-Ni alloy system is one of many binary systems in which the supersaturated solid solutions may exhibit a multistaged precipitation behavior during aging. In addition to the equilibrium phase separation, which was studied extensively years ago in the range 400" to 600",&apos; there exists at least one earlier stage of precipitation, i.e., preprecipitation, which occurs below 300°C in quenched alls.-This note reports on some effects of composition on the preprecipitation in Au-Ni alloys as determined from resistivity measurements. The kinetics of the preprecipitation were studied in alloys of 15 to 85 at. pct Ni which were water- were found in alloys which after various quenching-and-aging treatments were slowly heated and cooled (1Z"C per hr) between room temperature and about 300°C. Two such heating-cooling curves for a 40 pct Ni alloy are shown in Fig. 2. Similar effects were observed in other 15 to 50 pct Ni alloys. These curves are characterized upon heating by two changes in slope indicated by A and B in the figure and upon cooling by a resistivity hysteresis of approximately the size of the original decrease in resistivity after the aging treatment. The inflection at B generally falls at about the same temperature for all heating curves for a given alloy and appears to be a critical temperature (T,) for the preprecipitation for that alloy. The values of T, for most of the 15 to 50 pct Ni alloys fall in the range 200" to 220°C. The position of the inflection at A depends upon the heat treatment prior to the heating-cooling run and perhaps the heating rate, which was held constant in these runs. The preprecipitates grown in by the appropriate aging treatments seem to decrease in size as the alloys are heated from A to T,, dissolve at T,, and do not reappear after cooling below T,. When similar heating-cooling treatments were performed on 60 to 85 pct Ni alloys, an entirely different behavior was observed. Typical results are shown in Fig. 3 for an 85 pct Ni alloy. In these

Jan 1, 1964

By R. W. Parsons

wben a displacement front encounters an isolated permeability heterogeneity, it will be perturbed. The details of this perturbation will depend on the beterogeneity size and shape, the Permeability contrast, and the mobility ratio. This paper deals with the displacement front behavior for one, simple, mathematically tractable model: a circular permeability discontinuity and unit mobility ratio. The progress of an initially planar front is shown for four permeability contrasts: k2/k1 = 0, 5/2, 2, m. The front distortion is more pronounced than streamline and isopotential distortion and it approaches a constant shape downstream from the discontinuity. INTRODUCTION The impact of reservoir heterogeneities on oil displacing processes depends upon the variation of the heterogeneous property (frequency distribution), its disposition (spatial distribution), and the inherent stability of the displacement mechanism.l The interplay of these factors plus the impracticability, if not impossibility, of describing a natural rock system in any detail makes exact displacement front movements difficult to determine. It is useful, however, to be able to qualitatively visualize what heterogeneities will do to a displacement front. In this respect certain simple models that can be treated analytically are of value. The following analysis will show the displacement front behavior for one such model. MODEL DESCRIPTION The flow field is two-dimensional and infinite in extent. The fluid flow is single phase, steady state and unidirectional at x, y = 2 m, or before insertion of the discontinuity. A circular permea- bility discontinuity is placed at the origin. Porosity and thickness are the same within and exterior to the heterogeneity. This is exactly the same model that was used by Greenkorn et al. to check analytically Streamlines as determined by Heie-Shaw flow models and finite difference computer techniques.2 FRONT POSITION CALCULATIONS The results of displacement front calculations are presented in Figs. 1 through 4 for four different permeability contrasts: k2/kl = O, %, 2, m. The times corresponding to the front locations are the Same for the 0 and cases! and for the 1/2 and 2 cases. The determination of front positions at various times is based on known analytical expressions for velocity potentials ().2 and stream functions ().2 These expressions are in terms of the x and y

Jan 1, 1969

By Douglas W. Fuerstenau, Kalanadh V. S. Sastry

A mathematical model is developed for flotation in a countercur-rent column where continuously generated air bubbles rise through a downward flowing pulp. The model is based on the assumption of axially dispressed plug flow of both the liquid and air-bubble phases. An appropriate flotation-rate expression, which takes into account the changing concentration of solid particles on the bubble surface, is formulated and applied to the column flotation process. Although a complete solution of the resulting equations is not possible for the general case, solutions for specific limiting cases have been obtained. From these, it is possible to predict theoretically the dependence of the column performance on certain variables. Specifically, concentration profiles as a function of height in the column have been calculated for various values of the characteristic dimensionless parameters. The effect of axial dispersion on the perforance of the equipment is pointed out. In recent years, there has been considerable progress in delineating the fundamental physicochemical principles underlying the unit operation of flotation and in advancing methods for kinetic analysis and process modeling of flotation.&apos; In general, nearly all such process research has been concerned with the analysis of conventional flotation equipment and circuits. From these investigations, the possibility of developing and designing flotation apparatus for more efficient separation appears limited with conventional equipment. How- ever, recently there has been an attempt to apply coun-tercurrent flow techniques to flotation in the context of a flotation column.- some of the results from pilot-plant studies2 indicate possibilities for success of this process at least in obtaining higher-grade concentrates though not higher recoveries. A flotation column operates on countercurrent principle in which bubbles continuously generated at the bottom of the column rise through the downward flowing slurry. A schematic diagram of the flotation column is shown in Fig. 1. The physicochemical principles of bubble-mineral attachment, using this flotation column, are essentially the same as those which prevail in conventional equipment, the only differences being in the flow patterns of the various phases. The salient operating feature of the column as compared to those of a conventional cell is that neither mechanical nor turbulent pneumatic agitation is employed. The column is

Jan 1, 1971

By P. N. Nikiforuk, M. C. Zoerb

An analog computer model has been developed of a large, walking dragline. This model permits changes in the configuration of the dragline, or changes in its digging cycle, to be readily investigated on a computer. As a result, it is possible to determine ways of improving the dragline performance without having to carry out many expensive experiments on the actual machine. This model can also be used as a simulator for dragline operator training. INTRODUCTION The movement of large volumes of material is always a costly operation and the increasing trend towards the use of large capacity equipment does not necessarily produce the economy desired. This problem is of particular concern to the mining industry in its open-pit operations where large draglines are used to remove the overburden. Since this operation often forms a very large part of the total cost of open-pit mining it is particularly important that it be kept as economical as possible. This requires that the dragline be operated at its maximum possible productivity. In order to optimize the operation of a dragline it is desirable that a suitable model of the dragline be available for study. Once such a model is available the effects of changes in the configuration of the dragline, or changes in its digging cycle, could be readily investigated on a computer and methods of improving its performance could be determined without having to carry out expensive experiments on the actual machine. Such models would be of use not only to dragline users, but also to the manufacturers of draglines for design purposes. Presumably studies of this type could eventually lead to computer-con trolled stripping operations. As far as can be determined very little work1&apos;2 has been done on the derivation of dragline models. Such models must be derived before work of the nature indicated in the previous paragraph can be carried out. As a small contribution to this field this paper describes work that has been carried out by the senior author during the past few years on the derivation of one such model. This model describes the drag, hoist and swing operations of a 35 cu yd, commercially available, walking dragline. This model was derived for use with an analog computer and can be used either for optimization studies, or for the training of dragline operators. DESCRIPTION OF DRAGLINE General: The particular dragline for which an analog computer model was developed is owned by the Great West Coal Company of Estevan, Saskatchewan. It is a walking dragline and its function is to remove 40

Jan 1, 1967

By Michael Epstein, Daniel E. Rosner

Fume nucleation sufficiently close to vaporizing suvfaces can augment net vaporization rates into cooler environments. Environmental conditions favoring large vaporization rate enhancements are briefly discussed and a previous theoretical treatment of this nucleation phenomenon is generalized to account for the self-regulating effect of condensalion-heat release within the boundary layer. Despite kinetic limitations on homogeneous nucleation, and latent heat release, non-diffusive condensate removal processes appear to make possible large enhancements in steady-state vaporization rates, provided surface temperatures are well below the boiling point. When condensed phases vaporize (or dissolve) into cooler media, the diffusion-limited mass loss rate can be strongly influenced by the process of nucleation/con-densation (or precipitation) within the thermal boundary layer. This condensation process (which typically leads to mists or fumes in the case of evaporation into cooler gases) has the effect of steepening the vapor pressure profiles near the evaporating surface, since the condensation zone acts as a vapor sink. However. the resulting enhancement in the diffusion-limited evaporation rate can be estimated (as first done by Turkdogan1 for the case of molten iron/nickel alloys evaporating into helium) only if one has independent knowledge of the critical supersaturation, sCrit(T), required to homogeneously nucleate the vapor.* In a recent reformulation and generalization of the theoretical model of Ref. 1 it has been shown that, when log sCrit is approximately linear in reciprocal temperature, rather simple expressions can be derived4 for the ratio of the actual rate of vaporization j" to either the minimum (no condensation) rate j"min, or the maximum (equilibrium condensation) rate j"max In the present communication we wish to briefly report on further developments and implications of the formulation of Ref. 4, with emphasis on i) environmental conditions favoring large enhancements in vaporization rate, and ii) the self-regulatory influence of condensation heat release (neglected in Refs. 1 to 4) on predicted vaporization rates. Additionally, we take this opportunity to correct several misprints appear- ing in Ref. 4, and comment on Elenbaas&apos;s recent criticism5 of Ref. 1. MAXIMUM POSSIBLE VAPORIZATION RATE IN PRESENCE OF CONDENSATION A nonequilibrium theory is of interest because of the very large difference between the minimum (no condensation) and maximum (equilibrium condensation) vaporization rate. The magnitude of this maximum possible enhancement can be shown quite clearly by combining a result of Refs. 3 and 4 with the fact that for most liquids there is a simple relationship between the molar heat of evaporation, A, and its boiling point, i.e., A/(RTBp) = C, where the constant C, often called the Trouton ratio, takes on values not very different from 11.* More generally, for any substance (including The Trouton ratio (which for water is 13, for methane, 10, and so forth) will be recognized as the ratio of the molar entropy change upon vaporization (at TBP or Ttransf) to the unlversal gas constant R. Its near constancy reflects the fact that the change in atomic order upon vaporization depends only weakly on the kinds of molecules involved. those that sublime under ordinary conditions) we can define a characteristic transformation temperature. Ttransf, by a relation of the form Ttransf =A/(CR), and then examine the maximum possible evaporation rates as a function of how far removed from Ttransf are the surface temperature, Tw, and ambient temperature, T. Subject to the assumptions: 1) equilibrium vapor pressure, pv,eq, everywhere small compared to prevailing total pressure, p, and 2) negligible effect of condensation heat on temperature profile, the maximum enhancement ratio was found (Eq. [17], Ref. 4) to be: where, for most vapors, Nu/NuD (the ratio of heat transfer coefficient to mass transfer coefficient for the same configuration) is a number near unity.* Ex- *An alternative derivation of the Nu = NuD special case of this equation. revealing its validity for arbitrary velocity/temperature profiles in a laminar boundary layer, is given in Ref. 3. amining this result for a "Trouton substance", one obtains the results shown in Fig. 1, constructed for C = 11. Since we are concerned with vaporization enhancements (j&apos;max/J"min > 1) at surface temperatures below Ttransf, this area of interest is shown unshaded. One notes that at a fixed ambient temperature (hence, T/TtranSf) there is a unique surface temperature, 2T , at which j"max/j"min attains its peak value; moreover, the peak enhancement ratio, see dashed locus. Fig. 1, is: (NuA/NuD)(C/4)(Ttransf/T,). Hence, if Nu = NuD, when the ambient temperature is less than 1/4 of TtranSf the peak enhancement exceeds the Trouton

Jan 1, 1969

Meeting of April 24, 1914.-President Thayer announced the appointment of the Committee on Safety and Sanitation. The Committee on Nominations for officers for 1915 was appointed, as follows: William J. Cox, Chairman; H. Poster Bain, Joseph Daniels, Charles E. Mills, R. V. Norris, E. Gybbon Spilsbury, and Herbert A. Wheeler. The request of twenty residents of Salt Lake City and vicinity for permission to establish the Utah-Nevada Local Section was granted and R. C. Gemmell was appointed Chairman of the Committee on Organization. The following resolution was adopted: Resolved: That under authority of Article V, Section 7, of the Constitution, a special Committee be and hereby is appointed, to consist of the President and six other members of the Institute, to be named by him, Who shall be authorized to appear before the proper authorities at Washington and urge that Mining Engineers be appointed upon the proposed Commission for revision of the Federal Mining Laws. Further Resolved: That the activities of this special Committee be restricted to the authority given in this resolution.

Jan 6, 1914

IN the extra-mural service being built up by the Engineer-ing Societies Library as its finances permit, an occasional large total charge is incurred for exceptionally protracted services. A western steel company, for example; was charged the unusual fee of $500. They wanted complete informa-tion on transverse tests of steel, and asked the library to compile copies of all accessible records. Weeks -of search-ing and photoprinting produced three volumes of data. Two years afterward the company&apos;s chief engineer told the director of the library that the cost seemed high when the bill was paid but that the volumes had been in constant use. The information had been worth thousands of dollars. A client who wishes to pay no more than a moderate fee for services can state to what limit he is willing to go. Thus he may specify that he would like searches made on a particular subject but that he does not wish to exceed $5 or $30- for the information. The library is as willing to perform a small service as a large one.

Jan 3, 1928

FROM north to south activity is picking up through- out the Labrador Trough-already shown to be one of the world&apos;s great iron ore provinces. Center of current activity and interest lies in the mid-southern part of the trough as drills, equipment, and . . . money start to pour into the area near Mt. Wright and Wabush Lake. First major announcement in the area came early this spring when J&L and CCI outlined an estimated billion-ton deposit for "future" operations. Later impetus came from rumored railway for US Steel&apos;s Quebec Cartier projects in the Mt. Reed area slightly to the south. As this issue went to press US Steel&apos;s request for bids on railway and hydroelectric construction, plus IOCC&apos;s decision to step up the time- table on its program in the Wabush Lake area east of Mt. Wright, triggered a flurry of other announcements involving many of the top U. S. and Canadian iron ore firms. Do not look for most of these place names in the average atlas . . . they aren&apos;t there yet, but they soon will be.

Jan 6, 1958

By W. A. Boyer

HOISTS for metal mines are seldom designed for H one particular depth. They are intended for an ultimate load and depth with a given speed but are first used to hoist from a shallower depth, gradually working to the ultimate as development progresses. Sometimes the mine is not worked on the upper levels because of the kind and grade of ore, the mining of which depends on market conditions. In this case the hoist may be used in the same working shift to lift ore, for example, from the 1200 and the 4400-ft level. This means that the safety factor of the rope should be considered not only when it hoists from the greatest depth, but also when it hoists from the upper levels. According to present safety factor standards, a hoisting rope can have ample safety margin when hoisting from the lower or lowest level and still be shy of sufficient safety margin when hoisting from the upper levels. This will be shown by curves presented in this paper.

Jan 10, 1954

By James E. Breland

A case study of tangible and intangible costs incurred by a coal mining company for meeting the requirements of the Federal Coal Mine Health and Safety Act of 1969 is discussed. For clarity, the data is presented on a "before and after" basis, with special emphasis on safety records, costs, and production performance. The cost figures have been subjected to outside verification.

Jan 1, 1975