Search Documents

By Marco Aurélio de Jesus Matos

Os compósitos possuem dois ou mais constituintes físicos. O Brasil produz uma vasta quantidade de fibras vegetais e as utiliza como fase de reforço. A gelatina é obtida da ruptura de ligações covalentes e formam géis termoreversíveis. Sua principal característica, a gelificação, envolve a renaturação da estrutura e, diante do nosso objetivo, foi utilizada como suporte para as fibras já que a gelificação forma uma rede tridimensional. As fibras foram padronizadas em 0,355 mm. A gelatina foi gelatinizada e a solução coloidal vertida em moldes. Os provetes ensaiados conforme ASTM D412. O acréscimo da celulose microcristalina não altera os resultados da tensão de ruptura. O módulo de elasticidade respondeu de forma inversamente proporcional ao aumento do teor de fibras vegetais. O aumento da resistência à tração e do alongamento do material, porém, não na mesma proporção, faz com que haja uma diminuição de seu módulo elástico. O módulo de elasticidade tende a diminuir devido ao grande alongamento ao passo em que o teor de fibras vegetais e gelatina aumenta. A variação do teor de fibras vegetais e gelatina alterou significativamente os resultados dos ensaios de tração. A tensão de ruptura aumentou proporcionalmente ao aumento do teor de fibras vegetais. O alongamento também aumentou com o aumento do teor de gelatina, não sofrendo variações significativas em relação à variação do teor de fibras vegetais.

Aug 16, 2017

By Márcio de Morais Tavares

A espectrometria de fluorescência de raios X (FRX ou XRF) é uma das técnicas analíticas mais utilizadas em geoquímica. Na indústria mineral também se utiliza a espectrometria de absorção atômica (AA). A comparação de concentrações de sílica e alumina de oito amostras padronizadas de minério de ferro obtidas a partir das técnicas FRX e absorção atômica, constitui o objetivo deste trabalho. Foram realizadas análises dos mesmos padrões em outros dois laboratórios para reprodutibilidade dos resultados. Foram utilizados um espectrômetro FRX e um espectrômetro de absorção atômica para realização dos ensaios. As análises produziram resultados satisfatórios, com desvios médios de 0,502 para a sílica e 0,096 para a alumina.

Aug 16, 2017

By Peter Grawenhof

In steel mills universal joint shafts, slipper spindles and gear spindles are used to overcome the design- and process- related offset between the axis of the motors and the work rolls. At the roll side the available space for the couplings is limited by the minimum work roll diameter. This leads to extremely high loaded components of the universal couplings especially at the roll side joints. Furthermore modern steel mills continuously strive to roll larger plates and materials with increased strength. This requires drive solutions with even higher torque capacity. For these applications conventional design joints are not sufficient anymore. Even alternative solutions such as hybrid- or offset- designs fall short. Therefore the companies Voith and BUMA Engineering developed together the new GearLink drive concept in close cooperation with the Voestalpine Grobblech GmbH. A completely new combination of universal joints and gear couplings offers an up to now unique solution enabling the use of 1,35- times bigger joint with a 2,5- times higher torque capacity and a 20- times longer lifetime. The GearLink system was first time successfully taken into operation at Voestalpine Grobblech in December 2013 and is up to now working without issue.

Aug 16, 2017

By Artur Fernando de Vito Júnior

Caracterizar propriedades de resistência à propagação de trinca em aços é um elemento central em métodos de avaliação de integridade estrutural. Tal caracterização, normalmente se dá por meio da obtenção de curvas de resistência à propagação estável de defeitos (curvas J-R) do material. Sendo assim, para tornar este estudo mais amplo, serão obtidas curvas J-R de um aço estrutural com o objetivo de elaborar um roteiro metodológico para obtenção de curvas J-R. O ensaio de tenacidade à fratura para obtenção da curva J-R foi conduzido utilizando a técnica do corpo de prova único (single specimen) empregando o método da flexibilidade no descarregamento (unloading compliance), segundo a norma de ensaios ASTM E1820. Para este estudo, foram utilizados corpos de prova compactos C(T) de espessura B=10,0 mm, largura W=2B e uma relação aproximada entre o tamanho de trinca (a) e a largura, a/W=0,5.

Aug 8, 2018

By David Fernando de Carvalho

Este estudo de caso foi solicitado por uma grande mineradora brasileira à Chemtech Engenharia, com o objetivo de avaliar um projeto de um Transportador de Correia de Longa Distância na fase conceitual, onde se buscava a otimização do consumo energético, mínimo investimento financeiro inicial e redução dos custos operacionais. O resultado deste estudo de caso foi usado como diretriz no projeto básico do equipamento, além de ser usado como referência para outros projetos similares.

Sep 25, 2017

By Janete Terezinha Ferreira da Silva Lecheta

A CSN Paraná, sempre trabalhando com a cultura de melhoria contínua, passou recentemente por uma reestruturação na gestão das informações estratégicas, mantendo o que já existia de eficiente e aplicando melhorias e novidades que trouxeram ganhos de produtividade, suporte na tomada de decisão e outros ganhos intangíveis. O breve estudo tem como objetivo apresentar o trabalho que foi feito na CSN Paraná, os conceitos utilizados e metodologias aplicadas para que esse trabalho fosse possível.

Aug 16, 2017

By Jackson Teixeira de Oliveira, Douglas Batista Mazzinghy, Vanderson Eney de Matos, Alexandre Camilo Leles de Figueiredo

This work studied the effect of different ball sizes in the secondary grinding stage of Samarco. The Moly-Cop Tools 3.01 spreadsheet was used for models calibration and simulations, considering grinding balls topsize of 15, 20, 25, 30 and 35mm diameters. A normal specific selection function up to the largest fed ore particle size (840μm) was obtained. The higher generation of fines and compliance with particle size specifications (+ 74μm and -44μm) proved to be more favorable for smaller ball sizes. The specific energy consumption was lower for the 15mm ball (10.7kWh/t), increasing up to the 35mm ball (13.0kWh/t). Although smaller diameter balls seem to be the best option for the size specifications, some factors may limit their use, such as: the higher generation of specific surface area; and the amount of ball purge in the discharge of the mills.

Oct 3, 2019

By John Malcolm Gray

Interest in X-80 linepipe steels emerged in the early 1980’s and it was first used in 1985 by Ruhr Gas [1]. The early steels were extensions of conventional Nb-V or Nb-Mo microalloyed X-70 steels but other alloying concepts emerged based on Nb-Mo-B alloying (NKSTAF [2] and ULCB [3]). The latter had acicular ferrite/bainitic microstructures and carbon contents below 0.05 percent. In parallel renewed interest developed in ultra low carbon (0.02 percent) higher niobium steels which had first been studied in 1962 [4]. Such steels exhibited excellent notch toughness when processed with high finish rolling temperatures (>950°C) which made them suitable for processing on weak, older rolling mills. With time such steels, designated “High Temperature Processed”, or HTP steels, were further optimized and produced in modern, very strong rolling mills due to their superior economy compared with traditional vanadium and molybdenum containing steels. The chronology of the HTP development is presented in the present paper. Full scale demonstration heats of a 0.06 percent carbon 0.10 percent niobium steel were produced by Bofors Steel Plant in 1972 and were converted from slabs to plates by nine different steel mills [5-7]. Commercial application in API Grade X-70 first occurred in Canada in 1974 [8,9] but the concept was only used sporadically after that until 1998 when it was applied for the API Grade X-70 Sour Service Cantarell Project [10] in Mexico. Soon thereafter, the El Paso Cheyenne Plains Project used a 0.05%C 0.095%Nb 0.27%Cr variant of the HTP steel [10-12]. Nowadays the HTP concept is being utilized for construction of approximately 6000 km of 48” OD x 18.4 mm X-80 per year in China. The metallurgical principles and history of the development are presented in details in this paper.

Aug 7, 2018

By Bernardo Martins Braga

O curto-circuito é um dos componentes dos modelos de compartimentos utilizados na análise das curvas de Distribuição de Tempos de Residência (DTR) de distribuidores para lingotamento contínuo. Foram identificados na literatura, no entanto, diversos exemplos de seu emprego incorreto. O presente trabalho discute a interpretação física do curto-circuito, as formas de sua quantificação e as consequências nocivas de sua presença sobre a limpidez do aço e o controle da temperatura do aço no molde. Mostra-se que o método de cálculo dos parâmetros dos modelos de compartimentos deve ser alterado caso haja curto-circuito no distribuidor. É constatado que o curto-circuito deve ser evitado durante o projeto de distribuidores destinados à fabricação de aços limpos devido ao risco de perdas metálicas por macroinclusões.

Aug 16, 2017

By Daniel Mapa Clemente

Processing of tin slags in reduction furnaces was studied in order to optimize tin recovery and reduce recirculation rates of slags containing thorium and uranium oxides. A theoretical approach considering a mass balance of the process was developed and adjusted by experimental results in order to predict the final slag composition. A metallic phase (FeSnSi) was discovered trapped in the slag due to high apparent viscosity, raising the FeO and SnO2 contents of the slag sample. This FeSnSi alloy is rich in tin and its recovery would help to reduce the slags recirculation. High contents of ZrO2 were found in the slag, restricting it from reaching complete fluid phase. Through an analysis of the slag in the CaO-FeOx-SiO2 and ZrO2-CaO-SiO2 phase systems it can be concluded that final slags should be modeled aiming fluid phase at working conditions and additions should be planned in order to control ZrO2 levels.

Oct 30, 2017

By Aaron Samuel Young, Hiago Antunes Amador de Oliveira, William Pratt Rogers

Low commodity prices and lack of new high-grade deposits are pushing the mining industry for innovation. Lean mining has been vastly discussed in the past decades as a way to continuously improve mining efficiency. Although very theoretical, lean mining presents a set of new solutions enabled by the digital transformation that the mining industry is going through. This paper proposes a framework for a short interval control system with the purpose to allow timely responses by front line supervisors upon operational deviations. In the first part, the author briefly reviews concepts of short-range planning and lean mining. Then, the materials and methods used for the development of the short interval control system are discussed. Finally, alpha trial results are presented, and next steps discussed.

Oct 3, 2019

By Christian Overhagen

In bar and wire rod mills, rolling procedures featuring three- and four-roll technologies are state-of-the-art to produce high-quality long products. While a rolling model for the three-roll process including an equivalent pass method was already presented by the author, pass design methods are dealt with in the current work. The geometry of the rolled product and roll grooves are described mathematically using functional contours, allowing geometric-numerical methods to be used for manipulation and deformation simulation of the rolled product. For a given pass, the output section is constructed using these methods. Roll force, torque and rolling power are calculated using the mathematical rolling model presented before. Interstand tensions are discussed as influencing parameters on the force, torque and power demands, as well as on the section shape. A mathematical model for the influence of interstand tensions on lateral spread is incorporated in the model. To complete the pass design model, elastic mill stand feedback is considered in terms of a fixed elastic modulus for each rolling stand, the elastic feedback and therefore cross-sectional variation due to elastic mill spring being calculated iteratively from the roll force by application of the Gagemeter equation. The interaction of section height and width faults due to elastic mill spring and spread variations is analyzed in detail and the consequences for the roll pass design are shown.

Oct 1, 2019

By Alberto Tremea

The eddy current system is universally recognized as a most suitable method to point out discontinuities or modifications on the roll surface. The automation of the controls through the implementation of sophisticated equipments on the grinding machine has favoured its employment in the roll shop. A big effort is still going on to clarify the best way to promptly identify situations that could be really unsafe for the roll life. The results presented in this paper have been obtained through an intensive activity conducted in field by Innse Cilindri on work rolls of finishing stands of hot strip mills. The correct interpretation of the eddy current signals and a good calibration of the automatic system have allowed, in many cases, a substantial optimisation of regrinding practices.

Aug 16, 2017

By Jose Maria Rodriguez-Ibabe, Ronaldo Antonio Neves Marques Barbosa, Douglas Glenn Stalheim

Major costs in the production of both flat and long commodity grade structural steel products include alloy, labor and energy. Flat and long commodity grade structural steels such as ASTM A36, ASTM A527Gr50, S235, S275, S355 and other equivalent world societal standards represent over 500 million annual tons worldwide. These simple commodity grades consist of a minimum of three base common alloying elements, carbon, manganese, silicon and then can be supplemented with microalloying elements of either vanadium or niobium. Since 2016 raw material costs for two of the five alloying elements in these commodity grade structural steels, FeMn and FeV, have risen significantly and/or have become volatile making it difficult to maintain stability in profitability for these commodity grades. For steel plants producing hundreds of thousands and in some cases over a million tons annually of these common structural steel grades because of the significant alloy cost increase for Mn and V alloy additions has squeezed profitability of these grades. These grades typically represent the base loading for cost controls in most all steel plants and hence a significant cost increase or volatility in two of the five elements used for these grades having a negative effect on overall production costs. However, with a proper strategy for alloy designs working in conjunction with the mills existing processing capabilities to achieve the desired end metallurgy/mechanical properties, alloy costs and operational efficiencies can be realized.

Oct 1, 2019

By Homero Delboni Junior, Thiago Nunan, Flávia Vargas

Ball mill liners perform two main functions in grinding process: protect the mill shell from the aggressive milling environment and delivery input power to the charge. When it comes to liners optimization the challenge are to prolong the service life and improve grinding performance. Some liners characteristics such as A / B ratio, lifters number, lifter height, and attack angle are extremely relevant to grinding process. By analyzing process data, and through DEM simulations application, these parameters were improved on W-mill liner, located at Vazante concentration plant. The new profile promoted a reduction of power variability between the final and the initial life cicle intervals and, therefore, better stability to circuit operation. In addition, the new liner service life reached 21,603 hours, 25% higher compared to the previous one in use. This optimized profile therefore proved to be able to improve its functions by achieving superior process performance combined with longer service life.

Oct 3, 2019

By Klaydison Silva, Maurício Curi Segato, Elves Matiolo, Neymayer Pereira Lima

Flotation is the main concentration process, has been applied with sucess for the removal of quartz on the iron ore industry aiming high quality concentrates. limiting the top size close to 0,300mm and the removal of slimes are fundamental for the efficiency of reverse flotation of quartz. The high consumption of reagents, leading to insufficient particle coverage, and increased foam stability, leading to the difficulty of removal of quartz particles, are the main deleterious effects of the presence of slimes. Recent characterization studies, together with the development of new collector of linear chain, allowed the obtaining of concentrate with SiO2 contents close to 3% with 94% of metallurgical recovery, based on pilot tests carried out on a sample flotation column of the Quadrilátero Ferrífero.

Oct 3, 2019

By Antônio Adel dos Santos

O controle da temperatura é fundamental no processo de laminação a quente dos aços, motivando a dedicação de esforços em estudos sobre a transferência de calor e na aplicação de melhorias operacionais. Neste sentido, o objetivo deste trabalho é apresentar o desenvolvimento, os resultados e as aplicações de modelos de cálculo da evolução de temperatura do aço durante a laminação a quente, desde o reaquecimento da placa até o produto laminado e resfriado na forma de chapas. São mostradas formulações matemáticas, métodos numéricos de solução usados, validação dos cálculos e a contribuição dos modelos para o entendimento e melhoria de processo. Todo esse desenvolvimento foi baseado em trabalhos realizados na Usiminas, nos últimos anos, cuja fundamentação teórica, buscada na literatura, foi adaptada e validada de acordo com as especificidades de cada linha. Além disso, os modelos foram implantados como simuladores offline, tornando prática sua aplicação pelos analistas de processo. São mostrados exemplos de cálculo do aquecimento de placas, da evolução térmica das placas nos fornos até a entrada dos laminadores, e da evolução do esboço durante a laminação de chapas grossas.

Jul 30, 2018

By Ângelo José de Santana Tavares Cavalcanti

Este trabalho apresenta o desempenho após a implantação do processo de produção enxuta na operação unitária de filtragem do processo de pelotização das usinas Itabasco e Hispanobrás, com o propósito de aumentar a produtividade, reduzir custos, reduzir paradas de usina e perdas de produção, otimizando as rotinas operacionais e a utilização da mão de obra, bem como a melhoria do ambiente de trabalho. Esse processo é pioneiro em regime de produção contínua.

Aug 1, 2018

By Robson Aguiar de Macedo

O estudo de ligas livres de Pb envolvendo o emprego de junções metálicas sob altas temperaturas tem recebido atenção especial, sendo desenvolvidas novas ligas com qualidade e desempenho adequados. Ligas Bi-Ag consistem em alternativas promissoras para a substituição das ligas de solda contendo Pb para tais aplicações, por isso devem ser melhor caracterizadas sob o aspecto de estruturas brutas de fusão. Assim, o presente trabalho objetiva investigar a liga hipoeutética Bi-1,5%Ag (%em peso) solidificada unidirecionalmente sob regime transitório de fluxo de calor. Será analisada a influência dos parâmetros térmicos de solidificação como velocidade de solidificação (VL), taxa de resfriamento (?) gradiente de temperatura (G) na microestrutura e na evolução de dureza da liga citada. Para determinação do perfil de dureza, foram realizados ensaios de dureza Vickers. Para obtenção e caracterização das microestruturas presentes no fundido Bi-1,5%Ag, fez-se o uso da microscopia ótica e da fluorescência de raios-x. Uma estrutura de dendritas facetadas de Bi circundadas pelo eutético Bi-Ag prevaleceu ao longo do lingote Bi-1,5%Ag. Verificou-se um aumento gradativo dos espaçamentos dendríticos primário (?1) e secundário (?2) à medida que a distância da base refrigerada foi aumentada. Em geral, os valores de dureza diminuíram para maiores valores de ?1 e ?2.

Aug 7, 2018

By Vitor Orlando Ferreira

The efficiency of an apparatus which uses a forced lubrication system, as well as the useful life of its components, is strongly related to the degree of contamination of lubricating oil. The presence of contaminants and the degradation of the oil itself cause it to release substances that fouling of the wall of the pipes. The cleaning and dialysis of the oil pipes, besides prolonging the life of the lubricant reduces wear of the components. There are several methods of cleaning in pipes, the problem is that some have abrasive characteristics, which could damage some types pipes. Among the non-abrasive methods stand the Flushing and Air scouring. Flushing uses the lubricating oil which circulates in temperatures alternating and high speeds, for generating turbulence to perform washing. The Air scouring method uses oil and filtered compressed air, injected into pipe, to generating higher flow, causing the power supply unit with fluid can work with lower power consumption and higher speeds, removing fouling of the pipe. The objective of this research is to evaluate the Reynolds number to correlate with the efficiency of cleaning the pipe. The method applied was the Air scouring and it was verified that the qualitative effects may occur when compared to Flushing. After testing, it was found that the chosen method brings significant changes in flow, and this flow regime varies considerably increasing the Reynolds number.

Jul 31, 2018