Search Documents

By Patrícia Mundim Campos Faria

The process of particle size reduction by grinding is inherently inefficient and involves high capital and operating costs. In particular, ball milling is one of the important unit operations in the iron ore pelletizing process. The mill product, due to its physical properties, determines the efficiency of subsequent stages of classification, filtration and pelletizing, thus impacting the quality of iron ore pellets. The work demonstrates the application of the population balance model in the optimization of a full-scale ball mil circuit grinding pellet fines with the aim to evaluate the optimal solids concentration to improve iron ore pellet quality. Initially, detailed experimentation was carried out in a 25.4 cm diameter batch mill and a relationship for mill scale-up using a linear population balance model in wet grinding systems was established. The selection and breakage parameters and the specific selection functions were determined for pellet feed iron ore. It was possible to identify the non-normalizable nature of the breakage functions of the ore studied, which were modeled properly. Afterwards, as a result of incorporating the specific selection functions and breakage functions into the linear population balance model, it was possible to predict product size distributions in the pilot and plant scale mills (0.416 and 5.18 m diameter, respectively) from data obtained in the 25.4 cm diameter mill. Finally, with this scale-up procedure it was possible to appraise the plant scale optimization via laboratory scale grinding mill tests. The effects of changing percent solids were assessed in order to improve the industrial mill performance and the optimal value should be in the range from 76 to 80%.

Aug 1, 2018

By Joachiim Lehner

The application of post-combustion (secondary oxygen) to avoid skull formation on BOF lances was tested in industrial trials. The main findings are that no negative impact on the metallurgical targets (i.e. carbon, temperature and phosphorus at end of blow as well as iron–oxide in the slag) could be observed. The technology is capable of avoiding the buildup of lance skull and consequently increasing the average life of lance tips. The application of post-combustion not only affects the skull formation, there are also interactions with the refractory lining, especially thermal wear, and the utilization of the process gases (CO Recovery) that have to be considered. Special attention has to be paid to the parameters determining the use of secondary oxygen because rather small changes can strongly affect the points mentioned above. Since August 2016, the PCD (Post-CombustionDistributor) lances are used on a daily basis in the steelplant LD3 in Linz.

Oct 30, 2017

By Frank Schrama

The Steel Plant Model (SPM) is an advanced logistic simulation model for steel plants. With the SPM, bottlenecks can be solved and logistics can be optimized. Both existing plants and greenfield designs can be simulated. All movements and actions simulated, from hot metal to cast products. Not only all major equipment and their relevant components (like a sublance) are simulated, but also ladles, scrap boxes, transfer cars and cranes. The whole plant is simulated in 3D and actual distances and speeds determine transport times. The SPM includes process time deviations and equipment downtimes for maintenance or unexpected breakdowns. This ensures more realistic and reliable results. Logistic optimization is based on comparison of different scenarios. For a new scenario, equipment and practices, etc. can easily be modified, added or removed. At the same time the SPM produces all relevant data for every new scenario, which can be presented conveniently. This makes the SPM the ultimate tool to find bottlenecks or optimize plant logistics. The SPM is validated for several plants world-wide, with different characteristics and layouts. The SPM not only realistically simulates existing plants with all utilizations, crane movements and waiting times, but also to accurately predicts the influence of plant modifications or unexpected events like breakdowns. Given the flexibility of the SPM, any (new) steel plant can be simulated quickly when a layout and the requested data are provided.

Aug 16, 2017

By Zhi Zhang

The ever increasing demand of high performance rolls in the late finishing stands (F5 – F7) for hot strip mills (HSM) requires better product solutions from roll suppliers. Roll development activities never stop at Union Electric Åkers (UEÅ) in order to meet the requirement. The HYBRID STEEL, a new concept of roll materials especially for the late finishing stands in the HSM, is successfully developed in UEÅ. This paper reviewed the development of previous ICDP as well as enhanced ICDP (eICDP) roll materials, and, the novel HYBRID STEEL roll grade. Rolls manufactured by this new grade have been used in several European mills. A significant improvement over the enhanced ICDP rolls has been observed.

Oct 30, 2017

By Mozart Henrique Teixeira

As reservas de minério de ferro da Mineração Usiminas S.A. (MUSA) estão localizadas no extremo oeste do QF e ocupam a porção ocidental da Serra do Curral (Alkmin, 2009 [1]), também chamada Serra Azul e inseridas no Supergrupo Minas / Formação Cauê. Abrangem as Minas Oeste, Central e Leste. Atualmente a classificação geológica industrial adotada pela empresa leva em consideração o teor de ferro, contaminantes e compacidade (granulometria) das rochas. Os minérios são separados em dois domínios litológicos, hidratado e silicoso. Estes domínios apresentam comportamento granulo-químico fortemente heterogêneo tanto lateral como em profundidade (Teixeira, 2015 [2]), este comportamento confere ao planejamento da lavra elevado grau de dificuldade em relação às estimativas de massas e teores no que se refere à separação dos estéreis e minérios. Até novembro de 2015 o Planejamento de Lavra de Curto Prazo utilizava modelos de blocos atualizados mensalmente para a liberação de planos de lavra mensais e estimativas de teores do ROM, porém, ao longo do mês os desvios de teor na alimentação da planta e dificuldades na execução da geometria planejada eram frequentes. Diante disto, com foco na redução destes desvios, passou-se a gerar os modelos de blocos semanalmente para confecção de programações de lavra semanais e diárias com expectativa de liberação de estimativas de massas e teores com maior grau de confiança e melhor previsibilidade das características granuloquímicas dos produtos finais. Para a elaboração dos modelos semanais foram adotados novos métodos nas ferramentas de topografia, amostragem de frentes de lavra e mudança na rotina do mapeamento geológico, que passaram a ser executados semanalmente. Os resultados obtidos foram as reduções de desvios de teores na alimentação dos processos unitários das plantas e na produção de granulados.

Oct 30, 2017

By Raúl Daniel López

Un objetivo de seguridad y calidad en los moldes de la colada continua de Siderar fue la de tener un menisco estable y controlado. A lo largo de los distintos periodos de inversiones y mejoras, el control de nivel de Siderar logro como objetivo contener su variación de nivel de acero en el molde en un rango de variación menor a +/-2 mm y con una velocidad de cambio inferior a 1,5 m/segundos. Esta etapa trajo una relativa mejora en los aspectos mencionados (calidad y continuidad operativa) pero el hecho de tener como sistema de medición de nivel un sistema radiactivo (fuente Co60 y contador de centelleo) mantenía serias limitaciones en ambos rubros dado que este sistema no diferencia la interface escoria /polvo colador con el menisco de acero. Este trabajo tratará de mostrar y contar las tareas de desarrollo y aplicación de esta nueva tecnología, hoy vigente en la nueva Colada Continua N° 2 (CCD2) y en etapa de puesta en marcha de la CCD1.

Aug 15, 2017

By Douglas Glenn Stalheim

The demands for improved mechanical properties in hot rolled long products are increasing as the expectations of global Standards and construction designer’s increase. Cost constraints limit the excessive use of expensive alloys to meet these expectations. In addition, depending on the mill, equipment can limit what can be realized to meet the increasing expectations. The most effective way to meet the increasing expectations for improved mechanical properties of optimum strength and ductility is through producing steel with as fine as possible uniform cross sectional grain size in the “as-rolled” condition. The best solution to the development of this fine and uniform cross sectional grain size is to develop a cost effective alloy design coupled with proper metallurgical process control implemented into an existing mill’s equipment capability and layout. In other words, properly bringing together alloy, metallurgy, process control and existing equipment capabilities to develop an optimum product that can meet the increasing demands of the construction designer. This paper is designed to give a solid understanding of the production and metallurgical requirements to achieve a grain size in “as-rolled” long products that is as fine as possible within the limitations of the process and production parameters of the individual plant.

Jul 30, 2018

By Dagoberto Brandão Santos, Kairo de Barros Guimarães, Túlio Magno Füzessy de Melo

The effect of the cooling conditions on the microstructure and hardness of a Dual Phase hot-rolled steel 800 MPa strength was investigated. Simulations of the cooling conditions using a dilatometer were carried out from samples of a hot rolled coil with variations of the intermediary temperature from 620 to 740°C, isothermal holding time between 1 and 10 s and coiling temperature between 50 and 400°C. In addition, two CCT (Continuous Cooling Transformation) diagrams were developed to evaluate the effect of the isothermal holding time on the phase transformations of the remaining austenite. It was observed that the intermediary temperature has a strong influence on the kinetics of the phase transformation, as well as the isothermal holding time influences the amount of ferrite formed and, consequently, the final microstructure and hardness of the material. The coiling temperature did not cause significant changes in the amount and morphology of the ferrite, but a gradual replacement of martensite with bainite was observed, which, in addition to the self-tempering effect, contributed to the hardness reduction.

Oct 1, 2019

By Diego Pacheco Wermuth

Micrometric surgical components typically have high geometric complexity and stringent regulatory specifications. These components need to have excellent mechanical properties and a high demand of products. Besides these factors, it is necessary to maintain a low manufacturing cost, performing essential research on new manufacturing technologies. Metal Injection Molding (MIM) is a process that has been explored , providing an interesting alternative for making medical devices. The research in the production of microcomponents obtained for MIM is gaining momentum and prominence, due to low cost and high productivity of this process. This paper is a study and development of feedstocks with AISI 316L alloy , which is known for its biocompatibility. Four feedstocks with 61%vol. of metal powder were analyzed by capillary rheometry and DSC/TGA.

Aug 16, 2017

By Piezanowski Ludivine

With the aim to reduce the hot metal production cost, ArcelorMittal Gent decided to integrate more ores with finer particle size distribution in the raw material mix for the production of blast furnace sinter. As a consequence of such an increase of finer material in the sinter raw mix, the sinter machine productivity and the quality of the sinter are affected. In order to compensate this impact, modern granulation technology can be employed. Within this context, ArcelorMittal Gent has invested in a vertical intensive mixer. The equipment was placed before the existing drums, with a function of “mixer”, whereas the drums are fully optimised for the nodulizing process. The paper presents the results of the industrial operation during the commissioning phase of the new equipment. Gradually increasing the proportion of fine material in the sinter raw mix has made it possible to compare the performances of the old system using drums for mixing and pelletizing with the new system using an intensive mixer combined with a nodulizing.

Aug 1, 2018

By Jean François Stumper

This paper presents the TMT “3D TopScan” profilemeter, which is a Radar-based profilemeter that measures the total burden surface within a few seconds and on a continuous basis. This equipment is based on an electronically steered solid-state radar scanner, such that a very large amount of surface data is collected within short time intervals. These new electronically steered antenna systems are the key to meet the demands for both accuracy and speed. The TMT probe is installed at a fixed location at the top cone, such that it does not interfere with the charging, enabling a continuous measurement and a compact design.Blast furnace charging optimization can be achieved based on its measurement data. The burden surface is continuously measured every few seconds, enabling the blast furnace operator to detect any details including asymmetries or irregularities in the surface pattern. A variety of process analysis tools are available. Due to the continuous and fast measurement, the burden descent speed can be supervised without process interruption on an ongoing basis. More accurate process models (layer models) than ever are obtained which fully consider the unsymmetries.This technology, developed by TMT Tapping Measuring Technology, is successfully in operation at Salzgitter Flachstahl GmbH at their blast furnace B. The probe and the data evaluation tools combine today’s technological capabilities in measurement technology with the practical requirements of blast furnace operation.

Aug 16, 2017

By Yuechang Wang

A new method of manufacturing the wavy-tilt-dam(WTD) mechanical seal has been mentioned. In this method, the special equipment is designed to provide a predetermined force to external and inner circular surface of the ring. After milling the end face of the seal by grinding miller and releasing the preload, the wavy-tilt-dam can be done on the seal surface. In this paper, a prediction model is built up to investigate the relationship between the predetermined force and the deformation on the surface of the ring by using ANSYS software. A WTD ring is manufactured by this method which approves that the prediction model is in accord with the real process and this manufacturing method of the WTD mechanical seal is a proper choice.

Jul 31, 2018

By Hormando Leocadio, CWM van der Geld, Julio Cesar Passos

Impinging water jets promote high heat flux extraction rate. Steel industry widely employs the process for accurate temperature control to improve the microstructure and to ensure adequate mechanical properties. The range of surface temperatures, heat fluxes and cooling rates are very large, which makes it important to obtain an accurate value of the heat transfer coefficient. This paper presents an experimental and numerical study of the heat transfer behavior of a high temperature (450°C - 900°C) steel plate cooled by a water jet at 20°C to 70°C. High-speed imaging (up to 20,000 fps) within water jet impingement zone allowed the characterization of the boiling regimes in the early stages of cooling. The effects of initial temperature, water jet temperature and velocity on the heat transfer coefficient were analyzed by inverse heat conduction method that predicts the heat flux and temperature on the top surface from temperatures measured with thermocouples inserted in test plate. Heat transfer is strongly affected by the initial temperature of the hot steel, water jet temperature and, less intensely, by jet velocity. High cooling rates start when liquid water is in direct contact with surface temperatures above 700°C.The results will contribute to the enhancement of the temperature cooling control on the runout table and cooling model employed at Usiminas Hot Strip Mill.

Oct 1, 2019

By Peter Fajfa, Heinz Palkowski, Jakob Kraner, Matjaž Godec

The study of asymmetric rolling on the AA 5454 aluminium alloy plates was carried out. The plates were taken directly from the industrial hot rolled sheet. They were cold rolled on the laboratory mill with different rotation speed of the upper and the lower work roller with the strains around 33 % and 44 %. To get closer to the industrial conditions the maximal dimensions of the rolled plates for laboratory rolling mill and the special industrial lubricant were used. After deformation the plates were annealed to the soft condition. This research was focused on all possible effects of asymmetric rolling: The reduction of rolling force, the increase of strain at same set roll gap, bending of workpiece, finer microstructure, more heterogeneous textures and as a consequence of that better mechanical properties. The asymmetric rolling with favourable mechanisms in the deformation zone has created the material with the homogeneous hardness in the cross section and with lower anisotropy, which is crucial for improvement of formability properties of aluminium work hardened alloys and to get closer to properties of steels. In the presented paper the general impact and different effects of speed difference of rollers was investigated on cold rolled aluminium alloy. Obtained and analysed results explain the function of asymmetry in rolling process and the options to implement the asymmetric rolling in industrial plant.

Oct 1, 2019

By Elaine Carballo Siqueira Corrêa

A busca por redução de peso e maior segurança dos veículos vem impulsionando a obtenção de novos aços de elevado desempenho. Os aços bifásicos vêm sendo desenvolvidos e utilizados devido a sua considerável resistência mecânica e boa conformabilidade. No presente trabalho foram realizados os recozimentos intercríticos direto e contínuo em um aço de composição 0,121%C-0,499%Si-1,58%Mn-0,021%Cr com o objetivo de avaliar os efeitos do tempo e temperatura de intercrítica na dureza da ferrita e do constituinte MA (martensita e austenita retida). A avaliação dos resultados foi realizada por meio de microscopia óptica, microscopia eletrônica de varredura e ensaios de ultramicrodureza. Foi observada a influência do tempo e da temperatura na morfologia e na quantidade de constituintes formados. Também foram verificados diferentes valores de dureza nos constituintes e ainda em distintas regiões dos grãos de ferrita. Os resultados indicaram maiores durezas para regiões próximas da interface ferrita/martensita e diminuição de dureza do constituinte MA e aumento dos valores na ferrita com a elevação do tempo.

Oct 30, 2017

By Matheus Soares Siman

A soldagem GTAW tem importância fundamental para a indústria não só pelo excelente controle do aporte térmico, como também ao fato de proporcionar, repetitividade e reprodutibilidade. No entanto, este apresenta uma série de desafios, principalmente em relação à determinação de algumas variáveis e como essas podem afetar a resistência das juntas soldadas. Neste trabalho, investigou-se a influência de diferentes procedimentos de soldagem em tubos de aço SAE 4130 sem costura com e sem a deposição e com a aplicação ou não de pré-aquecimento. Após procedimentos de soldagem, as propriedades mecânicas e a microestrutura da junta soldada, zona fundida, zona termicamente afetada e metal base, foram avaliadas por meio de ensaios de microdureza, de dobramento e análise metalográfica. Foi possível avaliar a influência da aplicação do pré-aquecimento e analisar as propriedades mecânicas e microestrutura das juntas soldadas. Os perfis de microdureza revelaram a importância do pré-aquecimento. O ensaio de dobramento possibilitou a avaliação das juntas de maneira qualitativa. Porém, um ensaio quantitativo, como o de tração, possibilitaria mais informações.

Oct 30, 2017

By Ricardo Wilson Nastari Denigres Filho

Durante estudos de síntese hidrotérmica (realizada em presença de ácido acético e em autoclave à temperatura de 160oC) com o propósito de obter-se boemita a partir de uma gibsita comercial, observou-se uma morfologia diferenciada nos cristais de boemita obtidos: os mesmos apresentaram-se na forma de placas finas de perfil pseudohexagonal. No entanto, quando a síntese é conduzida nas mesmas condições de temperatura somente em água destilada, a morfologia da boemita formada é a de cristais cúbicos. No intuito de tentar entender o mecanismo do crescimento dos cristais de boemita na presença de íons acetato, foram realizadas novas sínteses, envolvendo o mesmo procedimento de preparação, porém variando os meios nos quais a reação ocorre. A partir de novas sínteses realizadas com acetato de potássio em meio aquoso neutro (pH=7) ou ácido (pH=2), foi observado que a presença do íon acetato no meio reacional é determinante para a obtenção da morfologia lamelar. A estrutura cristalina dos cristais obtidos foi caracterizada por DRX e a sua morfologia foi examinada por MEV.

Aug 8, 2018

By José de Camargo

Em janeiro de 2016 a Russula foi contratada pela Dojran Steel (Sidenor) para a reformulação de sua planta de Nikolic / Macedônia. O fornecimento incluiu um novo laminador de barras e perfis com capacidade para atingir 350.000 toneladas por ano, composto de equipamento mecânico, sistema de automação, bem como todo o suporte técnico necessário para a Dojran Steel expandir sua antiga gama de produtos e melhorar sua qualidade de produto acabado. Ao final da reformulação, executada em várias fases, o novo laminador adquiriu capacidade para produzir toda gama de produtos desejada: - Redondos de 8 a 40 mm, - Barras chatas de 16 x 4 a 140 x 20mm, - Quadrados de 8 a 40 mm, - Cantoneiras de abas iguais de 20 x 20 x 2,5 a 120 x 120 x 12mm,- Cantoneiras de abas desiguais de 30 x 20 x 3 a 120 x 80 x 10,- Perfil U (UPN) com altura de 30 a 140 mm,- Perfil I (IPE) de 80 a 120 mm e - Perfil T de 20 a 50 mm.

Oct 30, 2017

By Douglas Glenn Stalheim

Hot strip structural steel coil used in construction, engineering, transport, structural applications and other applications are widely used in yield strengths from 300 – 700 MPa. However, structural design engineers are now not only requiring various strength levels but also other mechanical properties, primarily good formability, toughness and weldability. To produce a balanced approach to a cost effective structural steel, hot strip coil requires an understanding of utilization of an optimized alloy composition designed for the layout/equipment capabilities of a given hot strip mill to produce the desired metallurgy for optimum mechanical property performance. The term “cost effective” does not just focus on alloy design, but also ease of overall processing from steelmaking, casting, rolling and cooling, stable mechanical properties with a statistically normal distribution, no downgrades/rejections and a product that the end user recognizes as being superior to others. The desired metallurgy is simply understanding what will be the optimum microstructure and cross sectional grain size/distribution needed to meet the mechanical property requirements. This paper is a follow up paper that previously described optimum base alloy designs along with steelmaking/casting processing considerations and will focus on proper reheating, rolling and cooling metallurgy/processing strategies to produce quality cost effective hot strip structural steel coil.

Aug 17, 2017

By Fabio Andre Brand

As empresas de classe mundial, para atingir a excelência, buscam inovações para maximizar a utilização dos seus ativos. Para estas empresas, os departamentos de manutenção assumem uma função estratégica e a utilização de metodologias como a Manutenção Centrada em Confiabilidade (MCC) tem contribuído muito para a obtenção de um desempenho positivo em seu sistema produtivo. Apesar das inúmeras vantagens da aplicação da MCC, identificou-se uma oportunidade de melhoria nesta metodologia, na etapa de aplicação do diagrama de decisão para escolha das tarefas de manutenção. Pois é dentro deste contexto que se insere o presente trabalho, que busca consolidar o processo de implementação da MCC, com a introdução de melhorias na etapa mencionada, voltadas principalmente para a sua utilização na indústria siderúrgica. Inicialmente, apresenta-se uma abordagem sobre os conceitos e métodos empregados na MCC tradicional. Em seguida, as melhorias propostas foram detalhadas junto com um estudo de caso, onde a MCC, já contendo os métodos elaborados neste trabalho, foi aplicada em uma empresa siderúrgica, sendo que os resultados obtidos demonstraram a adequação desta proposta às necessidades deste ramo industrial.

Oct 30, 2017