Search Documents

By M. J. Gavin

Within the past three years numerous inquiries for information on oil shale have been received by the Bureau of Manes. These inquiries have been increasing to such an extent that it has seemed advisable to issue a short paper prior to the publication of a bulletin on the subject, giving a, general discussion of the subject and a comprehensive list of references, so that those interested in the details of obtaining oil from shale can find additional information without much difficulty. Some of those who desire information are interested only in a general discussion of the subject, or are not in a position to refer to books and' articles describing the industry. The material for this paper is largely derived from published information on oil shale. Much of the information is obtained-from the books and articles mentioned in the list of references, and has been compiled with the intent of furnishing information to those not interested in all the details.

Jan 1, 1921

By Harald Ludwig

In 2002, excavation support work commenced on the Capitol Visitor Center project located adjacent to the nation?s Capitol building in Washington, D.C. The outlying work (Slurry Wall Work at Main Site is not discussed) consisted of providing excavation support for a new truck tunnel approximately 1900 feet long up to 50 feet deep as well as support for the new underground auditorium and Library of Congress tunnel. The excavation support consisted of a combination of conventional drilled in soldier beams, lagging, tiebacks and braces; intricate underpinning inside the existing Capitol building; support of an existing Russell Tunnel; soil nailing and tiebacks underneath the existing Russell Tunnel; two temporary bridges; and a deep soil mixed wall with lateral support provided by braces. As part of an on-going research program, some of these braces were instrumented with strain gauges. The deep soil mixed wall was approximately 300 feet long and 65 feet deep on either side of the truck tunnel. Approximately 34,000 sf of deep soil mixed wall, 90,000 sf of conventional excavation support, 200 braces, and 320 tiebacks were installed. This paper describes the large scope and breadth of the project that required a variety of excavation support techniques. A few of the challenges in designing and installing the support of excavation are discussed. This paper also presents the results of the instrumentation program conducted on the deep soil mixed wall, which stood open for more than a year.

Jan 1, 2006

By Rob Sloan, Simon Yu, Rob Robison, Mark Schmidt

"In 2000-2009, Highland Valley Copper (HVC) tested new generation 660 mm cyclones supplied by various manufacturers in an aim to replace existing first generation 762 mm cyclones without success. Due to plant infrastructure limitations, new generation larger (838 and 800 mm) cyclones were not feasible. In 2010, an approach of testing hybrid 800 mm diameter cyclones was initiated by HVC. The hybrid cyclone consists of an 800 mm cyclone upper head section and the use of existing 762 mm cyclone conical sections. Three hybrid 800 mm cyclones were engineered and fabricated, targeting a throughput of 850-950 mtph and were installed in the E line cyclone cluster. Since starting operation on September 20, 2011, three hybrid 800 mm cyclones have been running at combined throughput ranges of 750 to 1050 mtph. Based on plant Daily Met Reports, the test hybrid cyclones demonstrated a decrease in misplacement of coarse copper bearing material to the cyclone overflow and better cyclone efficiency when compared to the existing 762 mm cyclones at the same throughput. The hybrid 800 mm cyclones also demonstrated significantly higher capacity per unit when compared to the existing cyclones. Based on the improvement demonstrated in the full plant trials, HVC decided to install the new hybrid 800 mm cyclones in all five grinding lines starting in July, 2012. A more detailed discussion of the full plant trials and initial results of the first complete retrofit of E line will be presented. INTRODUCTIONHighland Valley Copper Partnership (HVC) is Canada’s largest base metals mine and one of the world’s largest producers of Cu-in-concentrate. The mine, located in the central interior of British Columbia, is owned (97.5% interest) and operated by Teck Resources Ltd. In 2011, HVC produced about 210 million lbs. of Cu and 8 million lbs. of Mo. HVC’s Mill Modernization Project (MOP), which was budgeted for $475 M, is currently under intensive construction and is scheduled for commissioning in Q1 2014. The following description was valid at the time of writing this paper.The operation has been expanded a number of times since the startup of the original Lornex mill in 1972. The plant started up with two 9.75 m (32 foot) diameter primary SAG mills. It was expanded in 1981 with the addition of a 10.36 m (34 foot) diameter SAG mill. In 1988, the Highmont concentrator grinding mills and flotation section were moved and attached to the Lornex mill site. This added two10.36 m (34 foot) diameter AG primary mills to the Highland mill. This brought the total number of primary mills to five referred to as Line A, B, C, D and E: three SAG mills (A, B and C) each with two ball mills in parallel and two AG mills (D and E) each with one ball mill. Each AG mill line is equipped with one short head pebble crusher. Ball mill circuits are classified using 8 clusters of ten Linatex 762 mm cyclones to reach a target P80 330 micron (equivalent 43% +100 mesh), before the cyclone overflow product advances to the bulk flotation circuit."

Jan 1, 2013

The above referenced contract between Badger Manufacturing Corporation and the U. S Bureau of Mines was executed June 30, 1975, as a result of the request for proposals for innovative machine concepts. We selected the cutting machine category because of the obvious lack of technical progress in this field for many years: Phase I of the contract required blasting fragmentation tests to determine proper blasting patterns for use with the auger-type kerf cutting machine. Phase II required design concept development for a machine capable of cutting a circular void as an aid to blasting.

Jan 1, 1975

By Erik Westman

Few studies have been conducted regarding the location, movement, and relative magnitude of the rear abutment of a longwall coal mine. The rear abutment, or the abutment pressure arch in the gob area, is controlled primarily by the quality of pack of the gob; the more compacted the gob is, the larger the stress would be theoretically. While there is no definitive location for the rear abutment, early studies showed that it could be located as far back in the gob as 300 m (1,000 ft). Like the location of the rear abutment, there has been little research conducted and very few answers as to the exact magnitude of the rear abutment load. Due to the fact that the rear abutment has been studied considerably less than the front or side abutment, the need for further studies is evident. From a ground control standpoint, the location and magnitude of a rear abutment could reveal information on the caving process associated with longwall mining, such as when the initial cave could be expected to occur in future panels. Besides the possible importance of the rear abutment from a ground control perspective, evidence related to the longwall rear abutment could be vital from a ventilation standpoint. The peak rear abutment location could serve as an area for harmful gases, such as methane, to accumulate because forcing air through repacked rock is more difficult than through loose rock. The objective of this study is to determine whether passive seismic tomography could image the location, movement, and relative magnitude of the rear abutment as the longwall face retreated, in addition to the forward abutment and gob. The results of a passive seismic imaging study at a western US longwall show evidence for the location, movement, and relative magnitude of a rear abutment. A clear zone of highlystressed strata is shown where the forward abutment is expected and a low-velocity, damaged zone is shown behind the face where the gob is located. These two zones retreat with the face over a three-week period. In addition, the images show a return to stress levels behind the gob that are slightly higher than overburden stress levels, which is presumably the rear abutment. This occurs at a distance behind the face that is approximately the same as the face width for this mine. We can conclude that passive seismic imaging can be used to identify the location, movement, and relative magnitude of the rear abutment of a longwall mine. This conclusion is dependent on the use of appropriate data collection and processing methods. The information provided can benefit the both ground control and ventilation engineers as they strive to improve the safety and efficiency of longwall mines. The knowledge associated with the rear abutment of a longwall could not only help increase production through proper initial planning and reduce down time, but it could also make positive strides in improving the overall safety surrounding a longwall mining operation.

Jan 1, 2012

By Robert J. Pokora

This report summarizes the work performed under USBM Contract No. J0100038, "Demonstration of Noise Control Techniques for the Crushing and Screening of Nonmetallic Minerals." The objectives of the program were to: a. Identify the prevalent sources of crushing and screening noise in portable and stationary plants b. Design retrofit noise control treatments for those sources c. Field test control treatments under actual operating conditions. A census of the nonmetallic industry was performed to determine the number and types of crushing and screening equipment. Based on the census, eight plants were selected and surveyed to assess the variety of noise sources, determine the worker noise exposure to those sources, and to identify possible constraints that had to be considered in designing and installing the retrofit controls. Three plants were selected from those surveyed and retrofit noise control treatments were designed, including: a. A primary crusher operator control booth b. Screen decks made of resilient cloth c. Screen feedbox impact pads d. Rubber feed plate for secondary crusher e. Rubber feed chute linings for secondary crusher f. Noise attenuating curtain for secondary crusher. A new primary crusher control booth was installed at one plant, and the operator noise levels were reduced from 97 dBA to 78 dBA. Screen noise at the two secondary crushing plants was reduced by 3 dBA to 7 dBA; crusher noise was reduced by 5 dBA at one of these two plants. Noise levels at normal outside operator and cleanup locations were reduced by 4 dBA to 7 dBA at one secondary plant, but operator/cleanup noise levels were not significantly reduced in the second plant due to rapid wear of installed materials. At one of the two secondary plants the retrofit noise control materials displayed excellent wear characteristics. The rapid wear of retrofit materials at the second plant was due to improper materials being supplied and changing circuit conditions.

Jan 1, 1982

By Robert H. Ridgway

This circular outlines salient facts regarding the pyrites industry of the United States and the world. It is founded chiefly upon published information available in the literature of the subject. The United States Bureau of Mines has in its files additional and more detailed data upon many of the subjects presented very briefly here, and will endeavor to assist the mineral industries and the public by giving further information in response to individual inquiries. The bureau will welcome comments, criticisms, and contribu- tions of data that may assist in making later editions of this circular of information more accurate, or may aid in developing more fully the files pertaining to pyrites.

Sep 1, 1931

By Christopher M. Kenney

Augered-cast-in-place (ACIP) piles have been utilized on commercial projects throughout many parts of the country for years, but are only beginning to be scrutinized for use on major infrastructure projects and other critical structures in some regions. Numerous engineers are aware that ACIP piles are an economical foundation alternative, and many technical papers have been presented that provide reliable methods of estimating ACIP pile load capacity. However, designers may not yet appreciate that the load-settlement behavior of ACIP piles is very similar to that of drilled shafts. This paper analyzes ACIP pile case histories from throughout the country and demonstrates that ACIP pile settlement under applied load is consistent, predictable, and very similar to the documented behavior of drilled shafts. This paper also presents a simple but accurate method of estimating ACIP pile settlement at the design load, and illustrates the need to estimate the equivalent diameter of the as-built ACIP pile when estimating pile behavior. Finally, this paper presents back-calculated values of the drained elastic modulus from the ACIP pile case histories that may be useful to those using more sophisticated methods of estimating ACIP pile settlement.

Jan 1, 2001

By Betty Gibbs

The Ore Body Modeling and Mine Planning Worshop, sponsored by the Society for Mining, Metallurgy, and Exploration, Inc. (SME), was held Feb. 22-24, 1991 before the SME Annual Meeting and Exhibit in Denver, CO. More than 40 people from mining companies, government agencies and universities attended. Eight vendors of integrated ore body modeling and mine planning software attended and presented the results of problem sets given before and during the workshop. They were: [ ]

Jan 1, 1991

By Stephen Tadolini

A unique circumstance created by monitoring a pre-driven longwall recovery room permitted measuring the stresses of a coal pillar throughout its entire life cycle in less than a week. A fender pillar, created in approximately the middle of a longwall panel at a depth of 650 ft, transformed from a solid barrier pillar - to a yielding pillar - to a residual pillar as 3 ft slices were methodically removed with the longwall shearer. The complete transformation, or life cycle, took place in less than 12 hours. The stresses were quickly transferred from the pillar onto the standing pumpable concrete supports and into the outby pillars. Roof to floor closure measurements, combined with the timing of the pillar behavior, provides a detailed look at the uncontrollable convergence of underground mine openings. Pillars remain the most important form of ?primary support? and understanding these life cycles is vital for safe and efficient mine design, in both room and pillar and longwall panel extractions.

Jan 1, 2007

By Ravi Ray, Kostas Kaklis, Zach Agioutantis

"Modern underground mining is becoming more complex and geotechnically challenging. The engineer uses numerical, analytical, and data-driven methods (empirical and/or experimental) or their combination to overcome these challenges. Each method has its advantages and disadvantages. Nevertheless, given the amount of innovation and experience involved in developing each of these techniques, it will be prudent to use all their benefits rather than favoring one technique over the other. Pillars are the most important support element in an underground mine. A holistic geo-mechanical solution needs to be determined to design mine pillars using a proper sequence and exact mix of the three methods. A combination of these methods, in sync, can encompass the several advantages of the three methods while eliminating their disadvantages. This paper presents a conceptual three-tier solution to the pillar design problem, to improve its design pedigree, using a proper combination of numerical, analytical, and data-driven methods. At the focus of this proposed method lies the Ground Reaction Curve (GRC) concept.INTRODUCTIONAlthough the stability analysis of underground excavations is a challenging problem, its understanding has improved tremendously over recent years through the use of improved tools and techniques. The trial and error method was replaced with more scientific methods like the empirical and analytical methods that are still in use today. Empirical methods were developed based on large data sets obtained from experiments and observations (e.g., coal pillar strength equations). Analytical methods were developed based on mechanical understanding of stability (e.g., safety factor for vertical pillar loading, Convergence Confinement Method). Improvement in computing power and numerical techniques led to the development of several numerical methods (e.g., finite difference, finite element) suitable for geo-mechanical analysis.Each of these methods have certain advantages and limitations. Nevertheless, the user is often puzzled over the proper method selection and over the proper sequence of using them. This exercise becomes more challenging when different methods are combined, where, for example, one has to estimate the pillar strength based on empirical equations (e.g., Mark-Bieniawski coal pillar strength equation), determine the factor of safety based on an analytical approach (e.g., tributary area load divided by pillar strength), and analyze pillar-strata interactions using numerical analysis (see Esterhuizen, Mark, and Murphy, 2010b).Challenges increase when current pillar design methods are designed as passive structures to balance the fixed dead weight of the overburden. This classic suspension design approach does not recognize the self-stabilizing capacity of the overburden (Frith and Reed, 2018). A practical solution to address these issues is the use of numerical analysis. However, one should always keep in mind that the numerical modelling approach may have certain practical limitations."

Jan 1, 2019

By Bruno Sampaio Jannuzzi, Klayton Sebastião Leopoldino, Rodrigo Jorge dos Santos Arruda, Sergio da Cunha Motta

Devido à necessidade de mitigar os riscos aos quais os empregados próprios e contratados ficavam expostos, durante o processo de peação de bobinas, em porões de navios, e também de reduzirmos os custos nessa operação, concluímos que deveríamos alterar o processo para aumentar a segurança dos trabalhadores, com a eliminação de materiais perfurocortantes, gerar redução do esforço físico, com a substituição de equipamentos e, consequentemente, obter redução de custos e ganho de produtividade, no embarque de bobinas de aço, em porões de navios, no Sepetiba Tecon - Porto de Itaguaí.

Oct 1, 2019

By H. J. McQueen

Mineral and energy resource consumption were continuously reduced by process improvements as chemical understanding was developed and applied. During the past two centuries, technological improvements increased human productivity that was accompanied by social advances and labour saving products; however, these sometimes proliferated to endanger sustainability, e.g., automobiles. In the steel industry, precisely controlled rolling of HSLA steels required little extra mineral consumption but reduced weight and heat-treating energy. Continuous casting of slabs reduced scrap compared to ingots and energy for the homogenizing soaking pit. Al alloy extrusions were improved by retaining the strengthening in the near-surface substructure, of high strength textures and of press quenching that is suitable for direct age hardening. Continuous bar casting of Al-0.65Fe, coupled with rod rolling and followed by wire drawing with only a final recovery anneal, yielded electrical wiring for households to replace less plentiful Cu and later for light-weighting use in autos and aircraft Looking backwards, the 1970 decade saw the first oil crisis and inspired Ottawa to undertake a campaign to develop an energy strategy that would decrease dependence on imported fuels. One significant undertaking under Energy Mines and Resources was the organization of industrial energy conservation, managed by each industry association,that collected detailed current statistics and set the goals for a 2-year campaign. The metal producing industries, as compared by E.C.N. Perryman to about 7.2 exajoules (EJ) for the nation, consumed about 0.8 EJ, being about one third of all heavy industries. While manufacturing consumed 30.2% of total energy, it created 87.3% of total national dollar value. Within the industrial envelope, smelting and refining utilized 28% (0.67 EJ, mining beneficiation 6.7%, 0.16 EJ); there was a significant contribution to exports: 80% of iron ore and 70% of aluminium in 1973. A general concern was that decreases in ore grade would lead to a rise in energy expenditures countering benefits from processing efficiency.

Jan 1, 2012

Analysis of Procedures and Drivers for Industrial Waste Management

Sep 13, 2010

By Eugene W. Bartel

This report describes in detail the circuitry used in the Automated Time Domain Reflectometry System and the testing and modification done to the system to improve the units performance and consistency. The analog ATDR software is described and explained in detail. Also attempts to implement the same Assembly Language program in a higher level language (PLM) are documented along `h two versions of the PLM program - one which uses a data filtering approach to limit noise and another which uses data averaging to reduce noise. The field testing of the analog and digital ATDR units is described along with the hardware modifications that resulted. The analog unit has been abandoned and the digital unit adopted for most field tests. Tests indicate that the digital units are much more consistent and less confusing for the lay-person to operate. The results indicate that the it can locate an abnormality in a test cable to within 5% of the true location (provided the cable phase velocity is known). The units can consistently locate shunt type faults which are less than 300 ohms and series type faults which are greater than 30 ohms.

Jan 1, 1980

By W B. Gregg

The rock blasting and mining industries use a system of detonators and explosives for mining operations. Many detonators use small metal bridgewires, which are heated by passing a current through the wire, heating and igniting the pyrotechnic powder in contact with the wire. Typical bridgewires require a current of at least 3 amps, applied for a few milliseconds, for an explosive output. The semiconductor bridge (SCB), in comparison, initiates an explosive in 0.01 to 0.1 of a millisecond.

Jan 1, 1994

By Benjamin Cebrian

Traditional dilution control systems range from computer modeling, use of physical markers on the field as polypipes to a technology that marks some control points where displacement is measured. The latter includes walking over a muckpile which is prohibited by some mining companies as a safety measure. The new technology presented in this paper is a patented system that is installed on board excavators (backhoe or front shovel types). Several control points are set along ore/waste contacts and their position is uploaded on the corresponding shovel. The operator proceeds on mucking until he is alerted when reaching any of the several control points previously located in the blast patterns and that have moved with the muckpile. A case study is presented at a high grade copper mine, were unique 3D shapes are showing as a result of using an on-board excavator dilution control system. Both ore-loss or dilution cost of opportunities are analyzed.

By Mark P. Zaitsoff

The project involved design, construction, and testing of hydraulic models of culverts, decant and open channel spillways which are typical drainage structures used for protecting mine waste embankments. MSHA (The Mine Safety and Health Administration, U. S. Department of Labor) made a motion picture of the tests. Tests results and products in the forms of graphs, tables and films, demonstrate the principles and factors which govern the function and performance of the three types of drainage structures.

Jan 1, 1981

The Geological Resource Map of New Zealand (GERM) is a computerised inventory of aggregate, mineral, coal, petroleum and thermal water occurrences, containing summary information on location, production, geology, and geochemistry. The types of occurrences include quarries, mines, gold dredges, wells, outcrops, seeps, springs, and fields. The file contains entries for about 10,300 sites and is used to produce tables of data and maps at any scale, for single or multiple commodities. The published format is the New Zealand 'Geological Survey map series Geological Resource Map of New Zealand 1:250 000'. Seventeen of the 27 map sheets covering New Zealand were published by August 1991, with three more close to publication.

Jan 1, 1991

By J. B. Seymour

This paper provides an overview of the current use of backfill for ground support in underground metal mines in the United States and a summary of recent accident data reported for these mines by the Mine Safety and Health Administration (MSHA). Backfill mines comprise a major part of the underground metal mining industry and are particularly important in terms of the fatalities and injuries impacting this workforce. Ground falls are the leading cause of fatal accidents at these mines accounting for 50 percent of the total fatalities (4 out of the 8 fatalities that occurred from 2006 through second quarter of 2011). MSHA reported several different types of accidents involving backfill at these mines. While backfill ground falls do not occur frequently, these accidents result in a much higher proportion of fatalities than host rock ground falls. Backfill ground fall accidents are especially hazardous in underhand cut-and-fill mining operations where employees work directly beneath the backfill. An analysis of recent MSHA accident data supports the need for further cooperative research with the mining industry to identify and address ground control problems in underground metal mines using backfill.

Feb 27, 2013