Search Documents

By John J. S. Sebastian

A laboratory-scale investigation was made of the basic problems involved in developing a ceramic heat exchanger to operate at high temperatures for using nuclear heat from gas-cooled process-heat reactors. Technical data were obtained on transferring heat by forced-convection from helium to air in a single-tube vitreous-alumina heat exchanger. Coolant air was passed through the annulus parallel with, and either concurrently or counter to, the flow of helium inside the tube. The data obtained pertain to removing heat from the helium. Average inside film coefficients were determined at mean surface temperatures of 200° to 1,570° F., inlet-gas temperatures of 1,450° to 2,665° F., and Reynolds numbers up to 560. The gas-to-surface temperature ratios were varied from 1.05 to 7.6. The tabulated results are shown in the appendix at the end of this report. The film coefficients of heat transfer were correlated by taking into account the physical properties of the helium at the average fluid temperature. With experimental conditions pointing to a laminar flow, the Nusselt number was found to decrease as the ratio of gas-to-wall temperature was increased to a value of 3. However, within the range tested, gas-to-wall temperature ratios above 3 did not affect the Nusselt number, regardless of the value of the Graetz number. Thus, beyond this point any increase in this ratio ceased to influence the heat-transfer relationship.

Jan 1, 1962

By T. Fabritius, L. Hekkala, J. Härkki

The Outokumpu steel belt sintering technology is used for manufacturing chromite pellets that are charged into smelting furnace for ferrochromium production. Hot air is blown through the moving bed of raw pellets. Direct temperature and flow measurements are difficult to do in the bed of a real scale belt sintering process. Therefore, a tested and reliable mathematical model would be a valuable help for optimising operational parameters of the process and designing new constructional improvements. The aim of this work is to present a mathematical model that calculates the gas flow and temperature distribution in the bed of pellets and the atmosphere. Computational fluid dynamics program FLUENT is used to calculate the gas flow, composition and temperature of the gas in the sintering bed during processing. Energy equation for the bed, containing the effects of evaporation of water and oxidation of carbon and iron oxide, will be added to the model to obtain the temperature of the pellets. The porous media model used for pressure drop calculations in the bed is shortly discussed. A comparison between CFD-calculations and experiments with a pilot scale batch-sintering reactor are also presented. The final model can be used as an engineering tool when developing the process and the equipment further. Different designs can be easily tested with the model and the effects of the changes to the flow pattern and temperature distribution can be studied.

Jan 1, 2004

By H. Soto, J. Jara, F. Nava

"A combination of oxidation and precipitation was used to eliminate cyanide from gold milling effluents. Preliminary laboratory work developed with both synthetic cyanide solutions and with industrial effluents indicated that ozone can easily destroy free cyanide and weakly complexed cyanide (i.e. copper and zinc cyanide). In this case the reaction is quite fast and seems to be controlled by the mass transfer of ozone to the solution. Experimental results indicate that free cyanide and weak-acid dissociable cyanide in mill effluents can be reduced to less than 1 ppm. However, the iron-cyanide complexes proved to be quite resilient to destruction with ozone and they remained in the solution even after most of the free and weakly complexed cyanide was destroyed with ozone. These results were confirmed in a pilot trial developed at the Sphinx plant in northern Quebec.To deal with the problem presented by the presence of the iron complexes two different approaches were studied: use of a combination ozone-ultraviolet light oxidation, and the precipitation of iron-ferrocyanide complexes in the residual solution after ozonation. This last method proved quite promising since reduced the total cyanide levels of industrial solutions assaying as much as 250 ppm to less than 1 ppm of total cyanide. Control of the · pH of the solution was the key to obtain the precipitation of the iron complexes. The use of iron to precipitate cyanide complexes has the advantage of being less expensive and less toxic than copper (used by the Inco process)."

Jan 1, 1992

By G. E. Agar, W. B. Kipkie, V. K. Drylie

"This paper describes mineral processing test work on drill core samples from an ilmenite deposit in Terrebonne County just north of Montreal.Mineralogical examination showed that the intimate associa¬tion between ilmenite and hematite precluded their separation. The maximum concentrate grade was therefore limited to 22.9% Ti. Liberation of gangue from the hemo-ilmenite grains occurred around 400 µm, a size which proved to be too coarse for recovery by flotation.Other physical separation techniques, such as elec¬trodynamic, magnetic and jigging, were tried in order to take advantage of the relatively coarse liberation size. An all-flotation procedure and a combination of jigging and flotation yielded similar separations.IntroductionInco Metals Company, through its subsidiary Canico, optioned an ilmenite deposit in Terrebonne County, just north of Montreal, and conducted a drilling campaign to confirm previous geological assessments of the deposit and to provide core samples for mineralogical study. Parts of these core samples were used for mineral processing studies, which will be described in this report. The objective was to identify suitable upgrading procedures, to determine the optimum combination of concentrate grade and recovery, and to provide suitable batches of concentrate for further treatment."

Jan 1, 1980

By Ertugrul Alp

Alp & Associates - Who We Are ?? Canadian consulting company (1999-?) ?? Principal Consultant: Dr. Ertugrul Alp, P.Eng. ?? Over twenty-five years experience serving the chemical, mining, pulp & paper, energy, steel, and transportation industries, and government clients. ?? Ph.D. in Mechanical Engineering, University of Waterloo ?? Experience: ?? Westinghouse Canada, Atomic Power Division, Manager, Analysis and Modelling ?? Concord Environmental (later Bovar Environmental), Principal, Manager, Air Quality and Risk Assessment ?? Arthur D. Little, Associate Director, Safety & Risk Practice Leader in Canada ?? Member: NATO CCMS Pilot Project on Disaster Preparedness (1991-1993) ?? Chair: MIACC Risk Assessment Expert Committee, 1995-1999 ?? Member: MIACC Committees on Land Use Planning and Pipelines (1993-1998) ?? Member: CSA/Q850 Risk Management Standard Technical Committee ?? Member: CSA/Z1002 OHS Risk Assessment Standard Technical Committee ?? Member: CCPA/CSChE Process Safety Management Committee (1999-?) ?? Member: ISO-31000 Risk Management Standard Canadian Advisory Committee ?? Chair: CSChE Process Safety Management Committee (2005-2006) ?? Chair: CSChE Expert Committee on Risk Assessment (1999-2005) ?? CSChE 2007 Process Safety Management Award

May 1, 2008

By Gerson Evaristo de Paula Júnior, Bruno Santos Malaquias, Henriquison Magela Bottrel Reis

O desafio no processo de coqueificação está relacionado à elaboração de misturas de carvões que produzam coque com a qualidade para utilização nos altos-fornos. Foi avaliada, em escala piloto, a influência de materiais inertes (coque verde de petróleo [CVP], antracito e carvão com alto teor de inerte [CATI]) às misturas de coqueificação sobre a formação de microtexturas e a qualidade do coque. Os resultados indicaram que, para a mistura avaliada, a adição do CVP até 30% produziu coque com qualidade (DI15-150) adequada para os altos-fornos da Usiminas. As principais microtexturas foram do tipo mosaico, fragmentária, fusita, inerte anisotrópico e o próprio CVP. O antracito provocou redução significativa de DI15-150 e CSR. A análise de microscopia óptica revelou partículas livres na matriz de coque, contribuindo para a queda de qualidade. A adição de CATI às misturas de coqueificação resultou em forte queda na qualidade do coque e a microtextura do tipo mosaico foi predominante. De forma geral, o carvão com alto teor de inertes foi o que apresentou menos benefícios, diferentemente do CVP, que apresentou melhor resultado para ser utilizado nas misturas de coqueificação da Usiminas.

Oct 1, 2019

The ability to optimise a concentrator from mill feed to final products requires a simulator which integrates comminution, classification and separation modelling. In order to model this range of processes, such a simulator must handle a variety of information about the ore. The AMIRA P9 project has developed a whole-of-concentrator simulation capability which brings together a texture-based model of mineral liberation, quantitative X-ray micro-tomography analysis to measure the inputs required by this model, and a multi-component simulator software framework. In the context of this approach, the term ?multi-component? implies the ability of the simulation to handle many particle properties simultaneously; for example size, composition, density, floatability etc. The simulation software framework provides the means to manage the flow of data around a circuit flowsheet, allowing each process model to access the information relevant to that particular model. A case study based on plant data from a gold-bearing pyrite concentrator is used to demonstrate the capabilities of the multi-component approach in simulating circuits which contain comminution and separation processes.

Feb 27, 2013

By Henrique Gobbi Soares

Chapas expandidas são conhecidas como um material metálico com orifícios em forma de losango, cuja produção ocorre em uma máquina que utiliza corte sobre pressão e processos de alongamento para transformar chapas em metal expandido. Estas chapas são usualmente fabricadas em aço carbono, mas em função de serem susceptíveis a fenômenos de corrosão, estudos têm sido conduzidos com o objetivo de se avaliar a viabilidade de substituição destes aços comuns por inoxidáveis. Este trabalho consistiu em caracterizar e testar mecanicamente amostras representativas de chapas expandidas de aços inoxidáveis ferríticos (AISI 410D e AISI 444A) e uma de aço carbono ABNT 1010 com espessura superior às demais. A caracterização estrutural revelou que as estruturas de todas as amostras são influenciadas pelo processo de expansão, apresentando grãos com níveis de deformação e encruamento predominantemente nas hastes. Observou-se a presença de inclusões em diferentes níveis em todas as amostras analisadas, sendo os maiores níveis verificados no aço ABNT 1010. Os resultados obtidos mostraram que as chapas expandidas confeccionados de aços inoxidáveis apresentaram os melhores índices de resistência mecânica quando comparadas à chapa de aço ABNT 1010, mesmo este possuindo maior espessura.

Aug 7, 2018

By Renardir Peixoto Maciel Júnior

A extração de nanocelulose de fibras vegetais é um exemplo da crescente busca por materiais mais sustentáveis com bom desempenho e qualidade. Neste trabalho, foi extraído nanocelulose de fibras de bambu que são ricas em celulose, hemicelulose e lignina. Após alguns testes, percebeu-se elevada abundância de celulose, além de sua respectiva orientação nas regiões dos entrenós do bambu. Portanto, o principal objetivo é extrair nanocelulose dessa região, desenvolvendo uma metodologia eficiente na sua produção, haja vista que a extração de nanocelulose é bastante investigada, e adaptações foram feitas a partir de investigações apresentadas na literatura. As nanopartículas foram obtidas por hidrólise ácida a 64% após a mercerização e o branqueamento com NaClO. Para obtenção de resultados, as caracterizações das amostras foram feitas com Termogravimetria (TG), Termogravimetria Derivada (DTG), Infravermelho com Transformada de Fourier (IFTR) e tamanho de partícula por Potencial Zeta.Tendo como resultado,a observação de dois eventos na análise DTG: um em 54°C correspondente a perda de água e em 330°C correspondente a degradação da celulose. Os tamanhos das partículas em Potencial Zeta obtiveram picos em 257,1 nm (79,6%) e 67,9 nm (15,6%).

Aug 16, 2017

By John R. Eckel

A Iaboratory drilling rig has been devised and placed in operation which permits the application of hydrostatic, terrastatic, and formation pore pressures to a rock sample for drilling under controlled conditions. Calibrated rests of this equipment in-dicate qualitative agreerment with field results on the effect of weight on bit, rotary speed, and rate of circ~~lation on drilling rate. Tests under pressure, using water and air as the drilling fluids, indicate that when drilling saturated limestone samples, a pressure differential between hydrostatic and formation pressure is the only pressure which affects drilling rate. A differential in either direction causes a reduction in rate, but the same diflerential from the wellbore into the formation causes the greater reduction. Also, in lime.stone, air favorably affected drilling rote only when compared to water at high hydrostatic pressurre, all other conditions remaining constant. Large increases in drilling rate with air could be obtained in the laboratory only while drilling a shale, which offered a limited permeability to nitrogen and which could be drilled with a differential from the formation into the wellbore. In general, the magnitude of the changes due to the pressure effect were small compared to changes in drilling rate obtainable by changing either bit weight or rotary speed. INTRODUCTION In the course of Humble's drilling research program, the desirability of investigating several factors which lend themselves to laboratory rather than field study became obvious. Principal reasons for this are the expense involved in field studies and the difficulty of exercising the required degree of control. Of primary importance are investigations of the effect of fluid pressure on rock rate, the effect of pressure on rock drillability, and a study of the fundamental mechanics of rock failure and chip generation. Several years ago some work in the laboratory on the effect of mud properties on drilling rate was re- ported to the API', but the completion of this work and the investigation of the other variables affecting drilling rate required equipment somewhat more elaborate than that used on these earlier tests. This equipment has been assembled to form Humble's Drilling Engineering laboratory. To date only the effect of pressure on rock drillability while using water and air has been investigated, and this work is not yet complete. Facilities are available to investigate the effect of fluid properties on rate of penetration, and information is being assembled on a current basis on the mechanics of drilling. The sequence of presentation in this progress report is somewhat different from that in which the data were obtained since the order of ex-

By G. E. Geiger

The purpose of this research was to develop a computer simulator fur predicting the air quality in existing coal mines as well as a design aid for developing new mines. In addition to the air quantity flow, the other variables of tempera Lure, moisture, methane and respirable dust are necessary to determine the air quality. An additional feature of this simulator is that it allows parametric studies of these variables to explore the effect that these variables have on the air quality of an operating mine system. The research has also pointed out arias where more research is needed, and promote better and more systematic data taking techniques. Wang and Hartman (see Reference 9, on page 1-98 of Section 1) had already published a computer program to determine the ventilation of large mines, and Wang and Saperstein (see Reference 10 on page 1-98 of Section 1) later published a refinement of the work in the previous reference. These references were the starting point of the simulator developed by this present research effort, and Section 1 of this report is a slightly modified version of the original vent elation program. The modifications were necessary to permit the additional programs of temperature-moisture, methane and dust to be

Jan 1, 1972

By J. H. Zietsman, M. W. Erwee, P. J. A. Bezuidenhout, Q. G. Reynolds

"Pyrometallurgical furnaces are tapped through tap-holes that are opened with drills and oxygen lances. The lance is often used on its own or as the last step of opening the tap-hole. Interaction of oxygen with molten material inside the tap-hole can occur, and is a phenomenon that is not well understood. As part of a study that focuses on the effect of lancing on flow inside and around the furnace tap-hole, a cold-model validation was done. The validation study focuses on validating the MULTIPHASEINTERFOAM multiphase flow solver in OpenFOAM® for the problem involved. The sensitivity of the model to different materials properties (viscosity and density in particular) is presented with both cold models and the results from flow simulations in OpenFOAM®. IntroductionMany pyrometallurgical operations are carried out in furnaces where molten material accumulates continuously. Once enough material has accumulated and is ready to be removed from the furnace, material is tapped through one or more tap-holes in the furnace. Tap-holes differ significantly in both geometry and materials of construction, depending on the process involved – examples of different types of tap-hole configurations can be found in, for example, Nelson and Hundermark (2014). Tapholes all share one common feature: they are high, wear areas of the furnace. Molten material at high temperature flows through these areas, after which the tap-hole is sealed, usually using tap-hole clay. The purpose of the tap-hole clay is to harden inside the tap-hole and seal it until the next tap.Once ready to tap, a pneumatic drill and/or oxygen lance is used to open the tap-hole. The extent of lancing a furnace tap-hole depends strongly on the type of furnace. In, for example, many blast furnace operations lancing is limited as much as possible, and done only if drilling was not effective. In other operations, such as on small-scale pilot furnaces with short tap-holes, only lancing is used to open the tap-hole."

Jun 1, 2019

By S. Merjan

Three papers were presented for discussion at the conference: 1) Instrumented driven steel tube piles at Canary Wharf; author: A. R. Gaba, United Kingdom. The author described the Canary Wharf development in the London Docklands, and in particular, the decision to build over the water by driving open-ended steel piles 25m in length into the sands below the soft estuarine deposits. The tubes were then filled with concrete above the sand plug (usually 17m below pile head). Three trial piles were instrumented with: a) resistance strain guages on the inside of the tubes; b) vibrating wire guages on the re­inforcement of the concrete. The trial piles showed elastic behaviour in five cycles of lateral loading, while the verticle load tests showed a definite bi-linear load-settlement behaviour. The initial stiff portion was a result of frictional staff resistance, both inside and outside the tube, with the soil at the base contributing at higher settlements. Loads were taken to three times working load, with no imminent signs of failure.

Jan 1, 1991

By R. S. Dean

In general, the Division conducts investigations relating to the treatment of ores and metallurgical products from the condition to which they are mined to the refined metal. At the object of conserving natural resources and eliminating waste by furnishing information on current methods of metallurgical practice making fig fundamental studies of metallurgical processes and developing new processes and alloys to the point of demonstrating their or value. Office of the Chief Engineer The functions of the technical units of the Office of the Chief Engineer are indicates

Jan 1, 1941

By David Van Horsen

Operation and maintenance of California?s water tunnels is an important factor and vital link in California?s infrastructure. These tunnels are owned and operated by a variety of large and small private and public water and power utility companies, municipal agencies, and irrigation districts. Visionary pioneers such as Michael O?Shaughnessy (San Francisco Hetch Hetchy Water Supply System), William Mulholland (Los Angeles Department of Water and Power and Metropolitan Water District of Southern California?s Colorado River Aqueduct), and John Eastwood (Southern California Edison Big Creek Hydroelectric Project) built large and small water supply, irrigation and hydroelectric tunnels, which have supplied environmentally friendly-water supply, renewable electricity, and uninterrupted service to a burgeoning population and economy. This paper introduces these pioneers and describes several case histories and lessons learned during condition assessment and rehabilitation of tunnels providing enlightenment of California?s vital water projects.

Jan 1, 2008

By Fabiana da Silva Santos

O presente estudo fez uso de uma liga de NiTi, rica em Ni, elaborada em um forno de fusão por indução a vácuo - VIM e posteriormente refundida em fornos de arco elétrico com eletrodo não consumível de tungstênio – VAR. Com base nos resultados de Calorimetria Diferencial de Varredura (DSC), Difração de Raios-X (DRX) e Microscopia Eletrônica de Varredura (MEV) / Espectroscopia de Energia Dispersiva de Raios-X (EDS), foi possível observar a heterogeneidade composicional/ típica de fundido por processo convencionais, as inclusões de TiC e Ti4Ni2O provenientes da fusão no forno VIM, e o refinamento microestrutural e manutenção da sua composição original com uso de cadinho de cobre e câmara/atmosfera dos fornos VAR.

Oct 30, 2017

By Kurt RP Petersen, Hendriena van der Walt

With the decline in fine diamond production from the Argyle mine in Australia, there is a greater emphasis on efficiently treating the finer size fractions through a DMS circuit. Although it is generally well understood that smaller diameter cyclones are more appropriate for this application, practical results do not necessarily meet this expectation. In this paper the operational performance of particular sized cyclones throughout the group was compared. Based on the results there is evidence that under certain practical operating conditions, small cyclones are not necessarily best for fine size particle treatment, particularly given the production pressures faced by all mines. However, there seems to be considerable merit in using larger sized cyclones, which tend to exhibit less performance variability, irrespective of operation conditions.

Jan 1, 2006

By R. J. Lytle

INTRODUCTION Prior to excavation in soil and rock, it is useful to know the subsurface structure. This is important information both for safety and for equipment scheduling reasons. It is useful to know whether parts of the subsurface might be potentially troublesome or of different character than is generally thought present. By using geophysical probing, it is possible to infer the location and size of these unusual regions. The ground structure is commonly estimated from core samples taken from boreholes. These cores give a detailed knowledge of the structure in the borehole. However, knowledge of the structure exterior to the borehole can only be extrapolated from core data. By using seismic and electromagnetic cross-borehole geophysical probing, remote probing can be used to sense the region exterior to boreholes. A recent advance has significantly improved the state-of-the-art for defining the ground structure between boreholes. This new procedure utilizes large amounts of data and provides a detailed picture of the subsurface. The data processing algorithms used are similar to those in medical imaging of the human body using x-rays, a science called x-ray tomography. This imaging of the ground is called geotomography, which is a shortened acronym for geophysical tomography. Several examples of geotomography applied to imaging ground structure are presented. Our approach has been to probe the ground with electromagnetic and seismic waves. We map the region of interest with signals transmitted between multiple source and receiver pairs lowered in boreholes on opposite sides of the region (Figure 1). The received signals vary according to the transmission properties of the media

Jan 1, 1979

Mineral exploration and mining in New Zealand has had almost five years of new legislation. The requirement for different consents is a challenging, time consuming, expensive exercise but in most cases the new procedure is working, although the matter of obtaining access to land is still a major issue. Priority is critical. After lodgment of an application for a minerals permit there are many other matters to address such as identifying land owners, occupiers and administrators, preparation of access applications, consultation and preparation of various resource consent applications.

Jan 1, 1996

By Douglas Bartley, Jay Elkin

The state of Pennsylvania was at one time one of the leading coal producing states in the east. However, legislation and industry trends over the last 10 years have adversely affected the amount of bituminous coal mined in Pennsylvania and the whole eastern United States. The application for and approval of a new mining permit is a very costly and arduous task. When a new mining operation is established it is crucial that nothing within the operator’s control causes the operation to stop producing. This paper discusses the action taken by a small mine in Pennsylvania when their blast induced vibrations rose to levels that typically would have resulted in a total mine shut down by the regulatory body governing such operations.

Jan 1, 2003