Search Documents

The Skorpion process comprises three processing steps, atmospheric leaching in sulphuric acid, zinc solvent extraction and electrowinning to produce special high grade zinc. The major mode of impurity transfer was attributed to crud runs in the solvent extraction circuit. Crud may be described as a heterogeneous, partly inorganic, partly organic mass of material which accumulates predominantly at the interface between organic and aqueous solutions. The paper describes the route causes of the crud formation in the solvent extraction circuit and optimisation strategies which are being followed to prevent impurity excursions in electrowinning. Keywords: zinc oxide, solvent extraction, crud formation, colloidal silica

Jan 1, 2007

By Jack Magtoto, Lysa Voight, Tom Martin, John Forero

SUMMARY Commitment by all parties to partnering goals established early in the contract aided Affholder, Inc. in constructing 2,360m (7,700') of soft ground tunnel in Rancho Cordova, CA. Despite two zones of known contamination, encountering a zone of loose cobbles and boulders in a matrix of flowing sand, some perched water tables and a flooded tunnel after 2 upstream safety plugs failed, the Contractor finished the work 33 days early and only 1.91% over his original bid.

Jan 1, 2007

By R Ratlou

Increased contamination due to sand in spiral feed has had a negative effect on the efficiency of spiral concentrators at Navigation Plant. The no. 1 seam at Kromdraai opencast, which was previously mined by underground bord and pillar methods, is now susceptible to spontaneous combustion because of air ingress into the old workings which are exposed in the opencast high wall. This posed a risk in the loss of reserves to burnt coal. As solutions, buffer blasting of the preceding cut to collapse bords and soft overburden dressing of un-collapsed bords were implemented to prevent air entering the workings. The latter remedy resulted in increased contamination due to addition of sand in Run of Mine. After evaluating alternatives, a low capital option was selected. The 110t/hr Teetered Bed Separator (TBS) has been installed, primarily to desand and upgrade the feed to the spiral concentrators. The unit indicated an upgrade with a yield increase of 0.4% during test work and is currently showing an overall plant yield increase of 0.97%.

Jan 1, 2006

By Jaqueline Couri Rolim

Com o mundo globalizado, surgiu a necessidade de um novo ordenamento em termos de espaços produtivos e de dinâmicas comerciais, acarretando novos paradigmas nos sistemas portuários, em especial nas cidades com portos. Partindo-se da premissa que os portos apresentam não somente caracteres técnico-operacionais, e sim representam instrumentos a serviço do desenvolvimento, interligando sistemas de cidades e fortalecendo economicamente uma região, buscou-se descrever os principais aspectos de um sistema portuário em geral, apresentando exemplos de portos eficientes mundialmente. Foram, também, avaliados os impactos e interações com as cidades, e as condições necessárias aos portos. Objetivou-se identificar, especialmente para a cidade do Rio de Janeiro, o estado da arte do porto, bem como apresentar uma postura mais moderna e descentralizada com relação à gestão portuária. Considerou-se a importância que este porto agrega para o país, porque as atividades econômicas desenvolvidas em um raio de 500 km são responsáveis por 67% do Produto Interno Bruto (PIB). A metodologia utilizada neste trabalho foi pesquisa bibliográfica, exploratória em documentos com conteúdo atualizado sobre o tema proposto. As análises do conteúdo foram levantadas de forma indutiva. Como resultados, ressaltou-se a possibilidade de implantação de uma nova tecnologia de automação utilizada em vários portos do mundo, que prioriza a agilidade nas conexões que transportam bens ou serviços, tornando mais eficiente e eficaz os processos relacionados a porto-cidade. Foram também abordadas e propostas melhorias nos aspectos relativos a uma possível modernização na infraestrutura, na logística portuária, nos fluxos, nos aspectos socioeconômicos e nas políticas públicas, com intuito de melhorar a produtividade portuária, apontar soluções para o desenvolvimento e para a reaproximação do Porto do Rio de Janeiro com a cidade.

Aug 16, 2017

By Clair Murdock, David Heath

The 1,280 MW Sir Adam Beck II Hydroelectric Project was constructed in the1950s, at Niagara Falls, Ontario, Canada. The twin intake tunnels total over 17 kilometers in length and pass deep below the City of Niagara Falls. The tunnels were excavated using drill and blast methods, with a top heading and bench approach. The shot rock was loaded with electric shovels and transported to the five shafts with off-highway trucks. The tunnel muck was hoisted to the surface by skip and transported by truck to disposal areas. The volume of underground excavation for the 15.55 meter diameter tunnels and the shafts exceeds 3,500,000 cubic meters, then and now the largest underground civil works excavation by drill and blast in the Western Hemisphere. The lining required over 900,000 cubic meters of concrete. All of this work was completed in three years, remarkable progress, considering the technology of the day, comparing very well with the rapid excavation and tunneling methods of the twenty-first century. Big, fast, and deadly—at least 20 lives were lost in construction accidents.

Jan 1, 2007

Despite a long history of production of industrial minerals and rocks, New South Wales still offers significant opportunities for exploration for and development of these minerals. Exploration for opal, sapphires, and zeolites in the State has been particularly encouraged by pioneering geological studies by the Department of Minerals and Energy, which have resulted in the development of important new geological concepts and exploration techniques. Large areas with potential for these minerals have not yet been tested. In the case of sapphires, the studies have identified a new type of deposit which is'the source of most of the sapphires mined from alluvial deposits. Recent price increases for heavy minerals, a re-evaluation of previous exploration in coastal regions, and a recognition of suitable environments in inland New South Wales have stimulated renewed exploration both onshore and offshore and have led to increased production. Significant potential also exists for development of a number of other minerals, including: topaz, which occurs in large, unusual and perhaps unique deposits in northern New South Wales; dimension stone (particularly granite); bentonite; diatomite; and silica for metallurgical use. Potential also exists for development of construction material resources, particularly construction sand, which is in short supply in the Sydney region.

Jan 1, 1989

By T. T. Chen

Copper anodes generated from copper scrap are relatively rich in Sn, Zn and Fe. Because of the presence of oxygen, only trace amounts of Sn occur in solid solution in the copper crystals. Thus, Sn occurs mainly as SnO2, Cu-Sn-Ni oxide and Sn-Ni-Zn oxide in the copper anodes, and Zn and Fe occur mainly as minor constituents in the Sn-Ni-Zn oxide and Cu-Sn-Ni oxide. During electrorefining, these oxide species are liberated from the copper anodes and report directly to the anode slimes. The trace amounts of Sn present in solid solution in the copper crystals dissolve but reprecipitate as Sn arsenate or a Sb-As-Sn-O phase. Accordingly, high Sn contents in copper anodes do not lead to elevated Sn concentrations in the electrolyte.

Jan 1, 2010

By M I. Pownceby, N A. S Webster, R Pattel, N Ware

The decrease in quality of Australian iron ore, coupled with the demand for more efficient energy use, necessitates closer monitoring and optimisation of process conditions for iron ore sinter production. Sinter properties are correlated with the mineralogical content and traditionally, quality control has relied on methods such as Fe2+ determination, point counting via optical microscopy and automated electron beam techniques such as QEMSCAN; these can have a typical turnaround time of several days between sampling and reporting of results. As well, there is additional uncertainty around quantifying some of the complex mineralogical phases in sinter such as silico-ferrite of calcium and aluminium (SFCA) and SFCA-I, which are key phases influencing sinter quality. There is a clear need for the implementation of alternative analytical methodologies that offer a turnaround in hours or even minutes to provide information to accurately maintain production conditions.X-ray diffraction (XRD) is a technique widely used for the quantitative mineralogical phase analysis (QPA) of ores and processed materials in the iron ore industry. Partial least squares regression (PLSR) analysis methods have recently been suggested as an indicator of sinter Fe2+ content from powder XRD data without the need for rigorous and often time-consuming mineralogical analysis by the operator. In this study we provide results from the implementation of PLSR to predict the strength of iron ore sinter. Results are sourced from a well-constrained data set comprising strength properties (as quantified by a tumble index (TI)) from a series of compact laboratory test samples. Using this data set it was determined that PLSR has potential to be used as a method for calculation of sinter TI from powder XRD data and, therefore, process control.CITATION:Webster, N A S, Pownceby, M I, Ware, N and Pattel, R, 2017. Predicting iron ore sinter strength through X-ray diffraction analysis, in Proceedings Iron Ore 2017, pp 331–334 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 24, 2017

This is the seventh in a series of reports on properties of commercial motor fuels, made in accordance with a cooperative agreement between the Cooperative Fuel Research (C.F.R.) Committee and the Bureau of Mines of the United States Department of the Interior. The first report gave data on motor gasolines sold during the winter of 1.935-36.3/ The present report covering 1,87 samples represents the products of 83 companies plus those from the Pacific coast, which were averaged by the Pacific Coast Technical Group before being submitted and are published exactly as they were submitted. For the regular grade 985 samples consisting of 73 different brands are averaged. The premium grade consists of 489 samples of 40 different brands. The third grade has 401 samples averaged from 51 different brands. In this report the districts have been reduced to 21 by combining North and South Texas into one district. El Paso samples are reported with the South Rocky Mountain district, and. Amarillo, Tex., has teen included with the Middle Rocker Mountain district. In the present survey samples from Fort Smith, Ark., have been included in the Tulsa area, Indianapolis has been included in the St. Louis district. Cleveland represents the State of Ohio. Samples from Little Rock, Ark., and North Carolina have been included in the Memphis district. The Pittsburgh district includes samples only from this State and Wheeling, W. Va. The actual sampling points in each area are indicated on table 1.

Jan 1, 1939

The National Institute for Occupational Safety and Health conducted laboratory and field tests to evaluate the effectiveness of dust collector bags for reducing dust liberation and operator exposure from a roof bolter?s dust collection system. The laboratory tests evaluated the bag?s effectiveness to contain dust and the effect on canister filter loading in both a bag and bagless condition. The dust emissions from the collector?s exhaust were also measured in each condition during laboratory testing. Laboratory results show that nearly 100 percent of the test dust fed into the collector was captured by the dust bags. Loading and pressure drop on the dust collector?s canister filter is greatly decreased when using the bags, enabling longer periods of drilling without filter removal/cleaning. The field results showed that, even though dust standards were met, respirable dust in exhausted emissions was reduced around the bolter. Laboratory and field results show that benefits from use of the bags are realized in all areas of operator exposure.

Jan 1, 2008

By G. van Aswegen

The geometry and morphology of a set of low-angle fractures around a stope in a deep Witwatersrand gold mine are explained in terms of extension fractures forming under variable conditions of stress. Primary extension fractures (E1) form some distance ahead of an advancing stope along the s1, s2 plane. With stope advance, a couple of these fractures end up in a stress regime conducive to transpressional shear and a secondary set of extension fractures(E2) is formed at a high angle to the primary fractures. i.e. at a low angle to the stope. As the E2 fractures are undermined, they migrate into a stress regime of transtensional shear and a third set of extension fractures (E3) may develop between E2 fractures. These have sigmoidal shapes, being parallel to the E2 fractures at the E2 discontinuity where s3 is negative, and curved through the un-fractured rock between E2 fractures where s3 is positive at the instant of fracturing. The fractures all display fractographic features characteristic of dynamic extension failure with striae indicative of the direction of rupture propagation and the local, instantaneous orientation of s1.

Jan 1, 2012

By Harold J. Bennett

This study was performed by the Bureau of Mines to evaluate the potential supply of primary copper from domestic resources. A tonnage-price relationship was developed indicating the quantity of copper that could be produced economically from known deposits at various copper prices and at various rates of return on the required capital investment. Costs of production are based on estimated capital and operating costs for mining, concentrating, smelting, and refining the copper. Total known recoverable copper resources are 189 million short tons of which 83 million tons could be economically recovered assuming a price of $0.50 per pound of copper, credit for the recovery of byproducts, and a 12-percent rate of return on capital investment. The quantities of recoverable byproducts associated with the 83 million tons of recoverable copper are molybdenum, 1.8 million tons, gold, 43 million troy ounces, and silver, 740 million troy ounces.

Jan 1, 1973

By Dan A. Brown

This paper describes a method of conducting rapid lateral loading tests of deep foundations in which the load is applied to the foundation with a time duration of less than one second. For purposes of this paper the loading is applied using a pyrotechnic loading system commonly referred to as Statnamic. However, the method should apply to any lateral loading system which produces a force time history with a loading duration of 20 msec to 1 second. The test provides a measure of the dynamic and static response of the soil/foundation system and must be evaluated as a dynamic loading. Interpretation of the test includes a simple single degree of freedom (SDOF) model which can account for the inertial effects of foundation mass, system damping, and static foundation stiffness. The results of the test measurements are compared with four case histories in which comparative static load test data are available, including pile group foundations and large diameter drilled shaft foundations.

Jan 1, 2007

By S. T. Kok

This paper presents a case study in West Malaysia for passive piles failure in very soft marine clay in open excavation. In this particular case, the thickness of the very soft marine clay ranges from 5 m to 7 m (16 ft to 23 ft) from the ground surface. Preliminary site investigation reported SPT ?N? value of zero for the very soft marine clay. The design was based on a deep foundation utilizing driven piles to support the superstructure. During pile cap construction, the piles were subjected to uncontrolled open excavation, inducing bending moment in the piles, resulting in some cracked and broken piles. Analyses were carried out using an existing three-dimensional finite element code with a non-linear soil model to predict the response of these piles during excavation. Finally, the predictions of pile responses during excavation were compared satisfactorily with the observed results.

Jan 1, 2009

By J. Hindman, E. Moeller

Vermiculite is currently mined from shallow (less than 25 m or 80 ft) surface deposits throughout the world. The largest producers are Palabora Mining of Phalabowra, South Africa (ore stock is a phlogopitemica), Xinjiang Yuli Xinlong Vermiculite of Korla, China, and W.R. Grace of Enoree, SC (ore stock is a biotite mica). Smaller operations are in Australia, Brazil, Russia and Zimbabwe. They also produce vermiculite on a continuous basis but do not export any significant amounts of product to North America. Intermittent and poorly documented production on a minor scale is reported from Argentina, Egypt, India and Uganda. Worldwide vermiculite production in 2004 increased1.7 percent to 432.8 kt (477,000 st). North American production declined, while African and Chinese production continued to increase.

Jan 1, 2005

By L. K. Weaver

The objective of this study is twofold, The first is to present the composition of the offshore petroleum industry in terms of lease bonuses and the value of hydrocarbons produced from Federal offshore tracts. The second is to present costs of producing petroleum (oil and condensate) in the Gulf of Mexico with a financial analysis of an offshore operation. To prepare a financial analysis of an offshore operation, a model was derived to show the costs necessary to explore, acquire, develop, produce, and abandon a 5,000-acre block and the estimated income from the sale of the hydrocarbons produced. To establish cost and income guidelines for the model, a group of seven oilfields in the Gulf of Mexico ranging from 7 to 75 miles from shore and in water 20 to 130 feet deep was selected for study. A net profit or loss statement was prepared for each field and a discounted cash flow rate of return was calculated. Discounted cash flow rates of return for the seven fields range from 1.1 to 19.5 percent. Under the two specified conditions set up for the model (a 20-year and a 30-year oil depletion model), the rates of return are 17.2 and 13.7 percent, respectively. To January 1, 1959, the top four operators in the Federal offshore areas had paid approximately 40 percent of the amount spent on all lease bonuses and produced about 56 percent of the total hydrocarbons.

Jan 1, 1972

This Bureau of Mines report concerns two subjects important in the application of electric power in mining systems. Electrical transients and their suppression are discussed, and several considerations are explored with regard to the use of explosionproof or other electrical enclosures.

Jan 1, 1979

By R. Sankey, L. Gatty, F. Bizzozero, G. F. Shannon, F. Savaglio, L. McDonald

State mining regulations in Queensland stipulate that a mine be provided with an earth installed on surface and that all underground equipment that needs to be earthed should be connected via a copper conductor to this surface grounding point. The regulations further require that all exposed metal surfaces in underground substations be connected to an earth. In a study of earthing conditions at Mount Isa mine it was found that the physical anchoring of metal work at substations (with rockbolts and associated steel mesh) also provides an excellent electrical connection to the country rock. It was established that not only is the mine's earthing system grounded at numerous underground locations but also that such anchor points offer, in general, a path to ground with lower resistance than does the legally required grounding point on the surface. It is recommended that metalliferous mines should utilise a multiple-earth system and not a run earth connected to a single, above-ground earth point

May 1, 1991

By L. A. Cornish, S. N. Prins, R. Süss

The work is being done using the Thermo-CalcTM software, and the database is being built up by obtaining good thermodynamic descriptions of all of the possible phases in the system. The database supplied did not cover all of the phases, and these had to be gleaned from literature, or modelled using experimental data. Similarly, not all of the experimental data were known, and where there were gaps or inconsistencies, experiments had to be undertaken. A preliminary version of the database was constructed from assessed thermodynamic data-sets for the binary systems only. The binary descriptions were combined allowing extrapolation into the ternary systems, and experimental phase equilibrium data were compared with calculated results. Very good agreement was obtained for the Pt-Al-Ru and Pt-Cr-Ru systems, which was encouraging and confirmed that the higher-order systems could be calculated from the binary systems with confidence. Since some of the phase models in databases were different, these phases had to be remodelled. However, more work is ongoing for information concerning the ternary phases present in the Al-Cr-Ru, Pt-Al-Ru (two ternary compounds in each) and Pt-Al-Cr (possibly more than three ternary compounds) systems. At later stage of the work, problems with the thermodynamic descriptions of the Cr-Ru and Pt-Cr binary systems were found. A programme of experimental work to overcome these has been devised, and is being undertaken. Keywords: Pt-based alloys, phase diagram calculations.

Jan 1, 2006

By T. Patten

Inter-Mountain Labs, IML, performed a study comparing mining waste rock sample analysis by Net Carbonate Value (NCV) and Modified Sobek acid-base accounting procedures. The study looked at 468 waste rock samples and compared the data for Neutralization Potential (NP), Acid Generation Potential (AGP), Net Neutralization Potential (NNP), and the ratio of NP/AGP. The study found that a majority of the samples were below 50 Tons CaCO3/kTons. This subset of ?low-level? samples was also examined separately for Acid Base Accounting parameters. The analysis compared the NCV procedures to the Modified Sobek procedures and concludes that the NCV procedures are as protective of the environment as Modified Sobek procedures.

Feb 27, 2013