Search Documents

By Othon do Rêgo Monteiro Neto

[The present study has investigated the extraction of copper from a chalcopyrite flotation concentrate using an adapted strain of Thiobacillus ferrooxidans and shake flasks, tank leaching and Warburg respirometer techniques. From the shake flask experiments, the activation energy and the frequency factor have been determined to be ?ka = 59.4 kJ and A = 3.3 x 105 S-1, respectively. The temperature coefficient was found to be Q10 = 2.2 in the range of 20 to 35°C. It was suggested that the reaction mechanism of chalcopyrite leaching by T. ferrooxidans involves the formation of an activated complex. whose thermodynamic values have been calculated to be ?G? = 92.1 kJ, ?S? -148.8 J K-1 and ?H$ = 47.8 kJ. The maximum volumetric oxygen mass transfer coefficient for the reactor leaching was found to be achieved by using an optimum air flow rate of 1970 cm min l at a rotational frequency of 1000 min-1. The highest copper extraction in tank (reactor) leaching experiment was 86.8% after 17 days of leaching, while in the sterile runs the corresponding copper extraction was only 40.1%. The copper extraction was suggested to be diffusion controlled. The power requirement of the aerated reactor was calculated to be Pg = 2.02 watts. During leaching, the oxygen saturation concentration was found to be C* = 6.70 mg dm-3. Using the gassing out method the critical oxygen concentration was assessed to be CCrit 0.05 mg dm 3. From the Warburg experiments, the kinetic parameters of the Monad equation were derived with a new evaluation technique to be Vmsp = 9.0 µm3 02 min-1 mg protein-1 and K = 7.4% pulp density for the effect of substrate concentration. The order of reaction and the overall reaction rate constant were determined from the modified van't Hoff plot to be n = 0.0 and k = 1.49 p dm3 02 min-1 mg Protein -1 for the chalcopyrite concentrate oxidation by T. ferrooxidans. On the basis of this experimental work, a preliminary flow sheet has been proposed for the bioextraction of copper from flotation concentrates.]

Jan 1, 1985

By Julver Álvarez

El presente trabajo describe el comportamiento estructural y mineralización del estaño-cobre en la mina San Rafael, Puno. En este sentido, las pizarras de la formación Sandia del Ordovisco Superior, por metamorfismo de contacto con el intrusivo, han sido transformadas a hornfels, que junto a las cuarcitas se presentan algunas veces como una cubierta superficial sobre el intrusivo. Asimismo, los intrusivos y las pizarras son favorables para la mineralización de estaño, aunque los cuerpos del mineral son más definidos y persistentes en el intrusivo.

Sep 13, 2001

By Liming Yuan

A study of the ignition of non-fire-resistant hydraulic fluid sprays was conducted by the National Institute for Occupational Safety and Health. Both an open flame and a hot steel surface were used as the external heat sources. With the open flame as the heat source, the minimum oil temperature and minimum spray nozzle pressure that resulted in an ignition were measured. The effects of the distance between the open flame and the nozzle and the nozzle orifice diameter on the ignitability of the hydraulic fluid sprays were examined. With the hot surface as the heat source, the minimum surface ignition temperature was determined. The degree of oil atomization and the relative direction of oil injection with respect to the hot surface are discussed. The ignition of oil sprays from the impingement of oil jets onto a vertical surface was also investigated. Finally, the results are compared with those obtained for fire-resistant hydraulic fluids. Keywords: Ignition; hot surface; open flame; hydraulic fluid

Jan 1, 2006

By D. A. Bruce

The Deep Mixing Method is a very valuable tool for combating problems related to in situ soil treatment, improvement, and retention. Many different variations are used throughout the world, and there is a correspondingly rich technical literature on the testing and properties of the treated soil. This paper provides a synopsis of these aspects.

Jan 1, 2001

By M. S. Safarzadeh

Over the last fifty years, the treatment of enargite concentrates has not received much attention primarily because of the availability of other clean concentrates suitable for processing with existing smelting and/or leaching technologies. As traditional copper ores have become scarcer, copper-arsenic ore deposits have garnered more interest. Arsenic release is a significant concern during the treatment of enargite by pyro or hydrometallurgical methods. Enargite is also very refractive in standard leaching procedures. Thus, economical treatment options for enargite concentrates are needed. Preliminary experiments have shown that the acid-bake leach process could be adapted and used for the treatment of enargite concentrates. In this study, low-temperature (100-400 ºC) sulfuric acid baking of an enargite concentrate followed by water-leaching has been evaluated. The results indicate the thermal transformation of enargite to copper sulfate during sulfuric acid baking, with most of the arsenic being released from the concentrate into the gas phase for baking at 400 ºC. The condition for maximum copper extraction (~100%) from the concentrate was found to be 400 ºC, sulfuric acid amount of 0.5 mL/g of concentrate, and 2 h baking time. Part of the arsenic was captured in the form of arsenopyrite (FeAsS). XRD analysis proved the presence of some arsenic in the form of claudetite (As2O3) in the baked concentrate. Acid baking of pure enargite behaved in similar fashion.

Jan 1, 2012

By J. M. Galera, M. D. Rodriguez, V. Pozo, S. Cooper

"Cobre Las Cruces mine extracts copper minerals from a VMS deposit located in the well-known Iberian Pyrite Belt (IPB). As an open pit, it is distinguished geologically from other IPB mines by the presence of around 150 m of Tertiary soft marls, known locally as the Guadalquivir Blue Marls, followed by a regionally important aquifer. Below the marls and aquifer the mineralization is hosted by rocks typical of the Palaeozoic within the IPB, comprising gossan, tuffs, slates, and sulphides.This combination of a substantially soft rock and more competent, older (but still occasionally problematic) Palaeozoic lithologies constitutes a unique geological framework and presents substantial challenges in maintenance of slope stability, and therefore operational safety, at the mine site. This paper describes the fundamental design, excavation, and monitoring measures implemented at the mine to maintain safe production, and the lessons learnt during the mine development. IntroductionAs a modern Spanish mine, Las Cruces is committed to the use of best available technology and practices with the aim of guaranteeing the production of ore in a safe environment. From a practical perspective, this implies the realization of a high quality pit design, ongoing geotechnical mapping of exposed slopes to ensure conformity with design, and use of leading geotechnical surveillance technology to complement visual observations. The focus of this article is to illustrate how, at a mine site with potentially problematic soil/rock conditions, multiple advanced techniques employed from design stage analysis through to final pit configuration and vigilance, were combined to achieve an overall control of the ground conditions. In Figure 1 the layout of the pit is shown, illustrating development at the beginning of 2015."

Jul 1, 2019

Geological hazards such as faulting, basement ridges, and zones of "thin" (< 6 m) coal have a major impact on mining economics of underground operations in Huntly Coalfield. Experience has shown that drillhole-based investigations do not yield sufficiently detailed models of the coal seam to allow management of the planning risks associated with these hazards. Consequently, operational performance is affected by unplanned costs associated with lower productivity, loss of coal reserves, and expensive strata control remedies in problem ground conditions. Huntly Coalfield is a challenging environment for acquisition of good quality seismic reflection data due to the very thick (10-85m) weathering layer. Since 1994, successful acquisition of 2D and 3D data has been achieved through a combination of careful testing of technical parameters and experimental trials prior to committing to production recording. High resolution seismic reflection (HRSR) is proving to be an investigations technique which generates accurate and reliable models of the coal seam and associated structures, such as normal faults and topography of the surface on which the coal seam rests. The HRSR technique has been applied and developed in the Okowhao Sector where Huntly East Mine is developing and extracting coal reserves. Results of a recent 3D survey demonstrate that this technique is capable of revolutionising risk management in mine planning for underground mines in structurally complicated coal deposits.

Jan 1, 1997

Solvent extraction has recently been introduced into Australian hydrometallurgical practice for the production of a high grade uranium concentrate from El Sherana ore by a sulphuric acid leach and solvent extraction process. The solvent is a 5 per cent solution of tri(iso-octyl)amine in kerosene modified with 4 per cent of a long chain alcohol. The stripping reagent is a molar solution of sodium chloride.Preliminary testing for the development of the process showed that the leach liquor was quite amenable to the solvent extraction process and that the equilibrium and rate considerations of both the extraction and stripping steps were very favourable.The industrial plant contains four stages of extraction, three stages of chloride stripping and one stage of secondary carbonate stripping. An internal type of mixer-settler is used for the stagewise contact, the design being based on tests with model equipment.The performance and control of the industrial plant is satisfactory; 99·7 per cent of the uranium is recovered for a loss of 0·3 gallons of kerosene and 0· 4 pounds of amine per 1,000 gallons of liquor treated.INTRODUCTIONThe processing of El Sherana uranium ore from the South Alligator River valley commenced in April, 1959, and thereby introduced into Australian hydrometallurgical practice the unit operation of solvent extraction on an industrial scale. Although there are now some twelve mineral processing plants in the United States and Canada using solvent extraction, its application to the field of primary hydrometallurgy is quite new. Prior to 1956 none of these twelve plants was operating and hydrometallurgical application waslimited to the refining of comparatively high grade uranium compounds and fission products from nitrate and nitric acid solutions.

Jan 1, 1961

By J. E. Tiffany, J. J. McKitterick

"IntroductionThe Bureau of Mines is investigating the fundamental factors in breaking down coal at the face, which govern the production of lump coal in typical mines working, different coal beds. Tiffany and Nelson in 1923-21 conducted tests on methods of blasting and use of different explosives, in a mine working the Pittsburgh bed in Pennsylvania. They determined come of these factors quantitatively, and compared their results with those obtained when the regular mine practice was followed.Results of Previous InvestigationThe tests by Tiffany and Nelson showed that the use of the cartridge of smaller diameter than that used in mine practice, resulted in an increase of 5 per cent in the amount of lump coal passing over a 1-1/4-inch bar screen, with a reduction of 32 per cent by weight in amount of explosive required. On the other hand, they found that on reducing the weight of charge 20 per cent, and using the cartridge of larger diameter, the round would not throw down the coal satisfactorily.Experiments with ""snubbing"" showed a similar improvement in quantity of lump coal, end the coal that was blasted rolled forward into the working place. however, in recent tests at another mine where the coal Lad different physical characteristics, snubbing did not always result in the coal rolling forward, on account of clinging to the ribs, and was not found to be an advantage. Therein the writers of this paper recommend that tests be made before deciding upon the adoption of snubbing in a particular mine."

Aug 1, 1925

By J. Szlazak, A. Tor, M. Borowski, N. Szlazak, D. Obracaj

This article presents the analysis of ventilation systems used in dead-end headings, while being drilled, in coal mines. Special emphasis is put on methane and dust hazard. Mathematical model for distribution of methane concentration in a heading is given as well. This model takes into consideration sources of methane emission and change in air flow rate due to leaks in a duct line. Solving equations presented in this article enabled giving dependencies describing distribution of concentration along the heading. On the basis of these dependencies there is a possibility of determining places with higher methane concentration and ways of combating this hazard. Determining the distribution of methane concentration in dead-end headings ventilated by a separate ventilation system is of great importance as far as work safety conditions are concerned. The information obtained may be of use when finding proper places for installing methane sensors. Three kinds of separate ventilation systems were distinguished: forcing, exhaust and overlap. The development in construction of fans and spare parts of a duct line enables using both forcing and exhaust ventilation systems in headings developed by continuous miners, with length above 1000 m, in the conditions of methane, temperature and health-detriment dust hazards.

Jan 1, 2003

Precast prestressed concrete piles designed to be end-bearing in a sand stratum at Drax Power Station met with extremely variable resistance during driving. Some piles came to virtual refusal almost immediately on entering the sand whereas others were driven to considerable penetration with very low resistance. Redriving and load tests on piles experiencing low resistance on initial drive showed that take up in strength occurred over a relatively short period of time. Investigations involving the use of pneumatic piezometers revealed the development of significant excess pore pressures during driving. Samples from boreholes showed that piles met the least resistance when the sand had a high silt content. Comparison with the original site investigation data demonstrated the difficulties in predicting detailed pile behaviour. The varied behaviour could not be related to the original borehole logs or to SPT or static cone penetrometer results. The factors controlling pile driving behaviour were essentially geological and could only be explained with reference to local soil grading.

Jan 1, 1989

By C. R. Summers

In response to the Coal Mine Health and Safety Act of 1969, mandatory noise standards have been developed that specify time-noise limits of mine personnel exposure. Most affected by elevated noise levels is the pneumatic roof bolter operator, both in terms of levels near or in excess of 115 dbA and in terms of length of exposure. Therefore, the principal emphasis of this Bureau of Mines report is on pneumatic drill noise control. It is not the intent of this report to suggest any drill redesign; instead, methods are suggested to reduce the noise level by complementing existing machines. An integral muffler system and a separate muffler system were tested in an attempt to lower pneumatic drill noise levels. Pneumatic drills, when new, operate at about 115 dbA when drilling in sandstone. Using the drill muffler systems, it was possible to decrease the noise level of a 115-dbA stope drill to approximately 100 dbA.

Jan 1, 1974

By I. Yildirim

Free energy of interaction between particles in water can be calculated if one knows the values of appropriate interfacial tensions, which in turn can be determined from the surface free energies of the particles involved. The latter can be determined using the Van Oss-Chaudhury-Good (OCG) equation. This method requires the measurement of contact angles of well-defined liquids on the surfaces of the particles of interest. In the present work, the contact angles were determined using heat of wetting, capillary rise, and thin-layer wicking methods. The results are compared, and the utility of the surface free energy data obtained from the contact angles are discussed.

Jan 1, 2002

By S. G. Hardcastle, C. K. Kocsis

"Worldwide, metal mines are going deeper. For example, in Canada there are six such mechanized mines planning production at 3000 m (10 000 ft). Working at such depths challenges all aspects of mining including the provision of ventilation to supply an equitable working climate for personnel and machinery.This paper explores the overall challenges of supplying ventilation in Canada’s deepest mines and how the volumes required could be minimized. This is essential because it must be remembered that ventilation and refrigeration are not only costly items to supply, but the magnitude of their cost is also very sensitive to the volume supplied. For the primary ventilation system this is obvious because of the cubic relationship between volume and cost.In deep mines, the main function of ventilation is the removal of heat transferred from the strata and generated by the mining machinery, and the air volumes supplied are designed accordingly. The second consideration is the removal of other pollutants that could be harmful to humans such as diesel and explosive fumes. However, the need for ventilation at its present design levels could be reduced. This paper discusses the implications of such technologies as: tele-remote mining and alternatives to diesel equipment on the magnitude of the volume supplied; ventilationon- demand which recognizes ventilation as a costly and limited resource; plus other aspects, such as the benefits of controlled recirculation, local cooling, and possibly heat rejection back to the strata to gain further advantage from new developments.Furthermore, this paper advances the need to be able to design ventilation systems more cost effectively and how such new advances as process simulators can be used in conjunction with ventilation simulators to explore the diverse options that could affect the air volumes required and provide more realistic economic data upon which to base design decisions."

Jan 1, 2004

By J. A. Stewart

"A common problem in the mining industry involves the overloading of established conveyor systems. This overloading can have a number of causes, such as new production technology or a changing market condition which increases demand. An overloaded system usually spells disaster and leads to clean-up problems, equipment failures and lost production. The Cape Breton Development Corporation's Lingan Mine had a serious overloading situation on its underground coal clearance system, and equipment was being damaged and production was being lost. It was rectified, in part, by increasing the coal clearance capacity through the use of booster conveyors. This paper discusses the problems which led to this situation, the booster concept and the installation of the first unit at the Lingan Mine.IntroductionThe Lingan Mine is a submarine coal mining operation with an annual production of 1.5 million tonnes from three advancing longwalls. Coal is conveyed 3400m up a 13% slope to the surface. Designed and installed in the early 1970s, the system's 820-tonne/hour design initially proved adequate; however, by the late 1970sthe system was handling surge loads of 1640 tonnes per hour due to the introduction of new face equipment.The coal clearance system consisted of three 485-Kw, two 210-Kw and one 105-Kw conveyors. Each conveyor was designed for 820 tonnes per hour using 1050-mm, Type 10 belt with a 35-degree troughing profile.There were many effects of the overloading on the system:• Loading beyond the physical capacity of the belt resulted in spillage along the conveyor, which increased operational and maintenance costs.• Overloading of the drive components resulted in premature equipment failures.• Spillage at the drive pulley often resulted in damage to the belt and pulley lagging and, under extreme conditions, the conveyor would require partial unloading before it would operate. This was a particular problem under wet conditions because the 485-Kw conveyor drives were fitted with single-drive drums."

Jan 1, 1982

By P. E. J. Pitfield, S. D. G. Campbell

The regional structure of shear and deformation zones in the belt, which is recognisable in plan view on Landsat TM images, is interpreted in terms of a conjugate-shear model. Gold mineralisation is related to this framework at a variety of scales. The principal recurrent structural geometries hosting deposits at mines such as Motapa, Durban, Charliesona, Cecil, Sunace, Turk group, Queens district, How, Peter Pat, Matabele Sheba, Goodenough, Old Nic and Bushtick are associated with shear zones and folds and include conjugate systems (shears, shear intersections, kink sets), side-step systems (en echelon segmentation, duplexes, monoclinal inflections, antiform-synform couplets) and interactions of the two. Linear sections of shear zones are generally poorly mineralised. The same geometries are identifiable on all scales from local to regional, so sections of regional structural lineaments or areas within mines should be prioritised for further investigation or development on the basis of the gold-bearing geometries observed to be dominant locally

Apr 1, 1996

By J. M. Houston

"In October 1982, Rio Algom Limited, purchased a tin prospect near East Kemptville, Nova Scotia, from Shell Canada Resources. This purchase led to the development of the first substantial tin mine in North America. This paper deals with the drillingand blasting operations at Rio Algom, in particular the use of emulsion explosives technology.This presentation describes what emulsion explosives and Heavy AN/FO are, and the support system used to deliver these products to the blast site.HistoryThe East Kemptville mine site was discovered by Shell Canada Resources (SCR) in July 1978. SCR started diamond drilling on the tin prospect in March 1979. After 8220 m of BQ drilling, it was estimated a reserve of 56 000 000 tonnes of 0.165% Sn was present.The property, which is located 54 km northeast of Yarmouth, Nova Scotia (Fig. 1), showed, after a feasibility study that, given an ore treatment rate of 9000 tonnes per day, a mine life of 17 years could be expected.GeologyThe tin deposit of the East Kemptville Mine, occurs in granitic rocks at their contact with metasedimentary rocks. The mineralization is in the form of cassiterite with associated sulphides of copper and zinc. The tin occurs in a stockwork of tin bearing Greisen alteration zones.East Kemptville MineThe mine planned an open pit operation with the first five years being mined at a rate of 14 000 tonnes per day, of which 5000 tonnes will be waste and low grade ore. Eventually, the total mining rate will be 21 000 tonnes per day, including 12 000 tonnes of waste and low grade ore. Figure 2 shows the general layout of the mine site.East Kemptville Chooses Emulsion ExplosivesIn December 1984, East Kemptville Mine awarded the Explosives Division of C-I-L Inc. a contract to supply explosives to the borehole. The system chosen gives East Kemptville the on-the-bench choice of regular AN/Fa, or a high density, Heavy AN /Fa product called SuperAN· or a water resistant emulsion explosive called MAGNAFRAC· for holes that cannot be dewatered.Emulsion ExplosivesAn emulsion is an intimate mixture of two liquids that do not dissolve in each other. Emulsions have contributed to our daily lives in such products as insecticides, salad dressings and cosmetics."

Jan 1, 1987

By Jovanir Francisqueto

O objetivo deste projeto foi elevar a produtividade do pátio de placas do Laminador de Tiras a Quente da ArcelorMittal Tubarão através da alteração do processo de sequenciamento do Laminador de Tiras a Quente com a criação do processo de realocação de placas após a formação da chance de laminação. O trabalho iniciouse com a definição de regras metalúrgicas de realocação de materiais e definição dos critérios operacionais e de atendimento a pedidos para posteriormente ser desenvolvido o software de otimização para a execução da realocação automática de placas na chance de laminação com foco na redução de movimentações no pátio do Laminador de Tiras a Quente. Com a implantação do processo/sistema espera-se conseguir uma redução de aproximadamente 60% nas movimentações de placas para formação da chance de laminação, conforme demonstrado nas simulações com dados reais e consequentemente reduzindo número de paradas de forno em função de problemas de produtividade do pátio de placas visando o aumento da produção do Laminador de Tiras a Quente em torno de 15 Kt/ano.

Aug 16, 2017

This is the seventh in a series of reports on properties of commercial motor fuels, made in accordance with a cooperative agreement between the Cooperative Fuel Research (C.F.R.) Committee and the Bureau of Mines of the United States Department of the Interior. The first report gave data on motor gasolines sold during the winter of 1935-36.3/ The present report covering 1,875 samples represents the products of 83 companies plus those from the Pacific coast, which were averaged by the Pacific Coast Technical Group before being submitted and are published exactly as they were submitted. For the regular grade 985 samples consisting of 73 different brands are averaged. The premium grade consists of 489 samples of 40 different brands. The third grade has 401 samples averaged from 51 different brands. In this report the districts have been reduced to 21 by combining North and South Texas into one district. Fl Paso samples are reported with the South Rocky Mountain district, and Amarillo, Tex., has been included with the Middle Rocker Mountain district. In the present survey samples from Fort Smith, Ark., have been included in the Tulsa area, Indianapolis has been included in the St. Louis district. Cleveland represents the State of Ohio. Samples from Little Rock, Ark., and North Carolina have been included in the Memphis district. The Pittsburgh district includes samples only from this State and Wheeling, W. Va. The actual sampling points in each area are indicated an table 1.

Jan 1, 1939

By Bruno Henrique Reis

O pó de aciaria elétrica (PAE) é um importante subproduto da indústria siderúrgica devido ao seu alto teor de Zn. Assim, tecnologias vêm sendo desenvolvidas visando seu aproveitamento, sendo o forno Waelz a mais difundida delas atualmente. Sua operação, por contar com um forno rotativo de grandes dimensões, que abriga uma infinidade de fenômenos físico-químicos, apresenta difícil previsibilidade ab initio. Por essa razão, este trabalho faz uso de uma ferramenta avançada da termodinâmica computacional, destinada à modelagem de processos, chamada SimuSage, a fim de modelar o seu comportamento. Para a criação do modelo utilizou-se também uma base de dados termodinâmicos advinda do software FactSage e a plataforma Lazarus. Com base em dados e resultados operacionais da literatura, foi possível realizar simulações no modo adiabático e comparar os resultados com os da prática industrial. Constatou-se uma grande sensibilidade do modelo com relação à quantidade de ar de entrada considerada no sistema, mas, também, boa aproximação dos resultados com relação à composição química dos produtos Óxido Waelz e Escória Waelz.

Aug 16, 2017