Search Documents

By Hirst H, McAfee J

In December, 1934, Mr. R. Sussex extruded some silver lead alloy wires in order to determine their electrical resistance. After the determinations had been made each wire was threaded through a sheet of paper on which the composition was noted. The wires were placed in a more or less tangled mass in a cupboard in March, 1935. It was not until September, 1936, that they were re-examined, and it was found that during the eighteen months some of the wires had corroded very badly. It was not until March, 1938, that the wires and the corrosion product could be examined, and the results are given in the following pages. It is of interest to note that none of the numerous silver-lead alloys which have been used for creep testing in the rolled condition have shown a similarphenomenon. The silver content of the rolled alloys was, however, never greater than 0·1%.GENERAL APPEARANCE OF THE CORRODED WIRESThe wires contained 0·1% up to 28% of silver, and a general examination showed that the corrosion had progressed farther the higher the silver content. This can be seen in Fig. 1, which is a photograph taken in March, 1938, of typical wires at a 'magnification of five diameters. In the early stages the corrosive action seems to be localized and an area of grey, yellow or reddish brown powder appears. The grey corrosion product is by far the one, most frequently seen, and in the later stages the only one visible from the outside. The reddish coloured product is sometimes seen on the residual metallic centre when the grey product has been broken away.The irregular extent of the corrosion can be seen in Fig. 2, which shows (natural size) the 5% silver wire after standing two years. The corroded parts are seen to be much thicker than the slightly corroded ones. The corrosion product, being non-metallic, is quite brittle and falls away from the wire on bending. In the extreme case the' whole wire has corroded and presents a cracked appearance as seen in Fig. 1 (281% silver).An approximate idea of the extent of corrosion can be obtained by measuring the diameter of the corroded part. The original diameter in each case was ·050/ ·051 inches and in Table I are given the diameters of the corroded parts after Hand 3 years respectively. When the diameter...

Jan 1, 1941

Amid some of the worst economic conditions that the mining industry has been faced with in more than a decade, the mood among the large crowd at the 114th Annual Northwest Mining Association?s annual meeting was surprisingly upbeat. More than 2,200 attendees showed up at John Asuaga?s Golden Nugget Casino in Reno, NV for the conference held Dec. 1-5. And more than 200 companies exhibited in 240 spaces, including SME and the Minerals Information Institute. The number of attendees and exhibitors were the most for the conference in more than 10 years. The conference was held in Reno/Sparks for just the second time in its illustrious history but began under the cloud of global financial turmoil. Prior to, and during the conference, the industry news headlines were grim, to say the least. An alarming number of mine plans and expansions had been put on hold; hundreds of miners across the United States had been or were in the process of being laid off; commodity prices were falling and some of the biggest mergers in the industry fell through while miners around the world put the brakes on to take a wait-and-see approach. It was a painful time for many, but the downsizing actions taken by many mining companies was exactly what needed to happen, according to Industry Outlook Luncheon featured speaker Frederick Sturm. He is the executive vice president and chief investment strategist and member of Mackenzie?s Investment team. He has earned a reputation as one of Canada?s leading investors in natural-based companies and he also manages the Ivy Global Natural Resource Fund in the United States Sturm said that the mining industry has fallen hard and that he expects it to bounce back quickly, before falling hard again. In these tough times, he said, the companies that have pulled back on production early are doing the right thing in the long run.

Jan 1, 2009

By M. Abdellatif

Keywords: Pyrometallurgy, furnace, DC arc furnace, smelting, silicon The technical feasibility of silicon smelting in a DC arc furnace was investigated. A graphite-lined furnace was operated at power levels of 150 to 160 kW, and 40 to 60 V. The average feed rate during the silicon production period was about 30 kg/h. The recipe consisted of pre-mixed batches of 28% petroleum coke and 72% lumpy silica. The target furnace operating temperature was set at 1600°C and then raised to 1700°C. In total, about 1.6 tons of premixed feed materials was processed over 16 feeding?tapping operations. The feed was manually charged into the furnace in sub-batches of 10 to 40 kg at a time. The total batch mass was set at 90 kg during the initial part of the testwork, and increased to about 120 kg for the rest of the campaign.

Jan 1, 2011

By John F. Gamble

Amphiboles are hydrated mineral silicates five of which occur in asbestiform habits as asbestos grunerite (amosite) asbestos, riebeckite (crocidolite) asbestos, anthophyllite asbestos, tremolite asbestos and actinolite asbestos] and non-asbestiform habits (grunerite, riebeckite, anthophyllite, tremolite and actinolite). The asbestiform varieties are characterized by long, thin fibers while non-asbestiform varieties such as cleavage fragments form short fibers with larger widths. The U.S. regulatory method for counting asbestos fibers (aspect ratio [>]3:1, length [>]5 µm) does not distinguish between asbestos and cleavage fragments. The method biases toward increased counts of non-asbestiform cleavage fragments compared to long, thin asbestos fibers. One consequence of this regulatory approach is that workers can be erroneously classified as exposed to concentrations of asbestos (asbestiform amphiboles) above the U.S. 0.1 f/mL exposure standard when in fact they are not exposed to asbestos at all but non-asbestiform amphibole cleavage fragments. Another consequence is that the known carcinogenic effects of asbestos may be falsely attributed to non-asbestiform amphibole cleavage fragments of the same mineral. The purpose of this review is to assess whether amphibole cleavage fragments pose the same risk of lung cancer and mesothelioma characteristic of amphibole asbestos fibers. We identified three groups of workers exposed to non-asbestiform amphiboles: two groups exposed to grunerite (Homestake gold miners and taconite miners) and one group exposed to industrial talc containing non-asbestiform tremolite and anthophyllite in St. Lawrence County, NY. In addition to assessing strength of association and exposure?response trends in the non-asbestiform amphibole cohorts, comparisons were also made with cohorts exposed to the asbestiform counterpart (positive control) and cohorts exposed to the mineral (e.g. talc) that does not contain amphiboles (negative controls). The cohorts exposed to non-asbestiform amphiboles had no excesses of lung cancer or mesothelioma. Similar results were observed in the negative control groups, in stark contrast to the excess risks of asbestos-related disease found in the asbestos cohorts. The only possible exception is the twofold increased risk of lung cancer where exposure was to industrial talc containing cleavage fragments of tremolite and anthophyllite. However, this risk is not considered attributable to the talc or amphibole cleavage fragments for several reasons. A similar increased risk of lung cancer was found in Vermont talc workers, studied in the same time period. Their exposure was to relatively pure talc. There was no relationship between lung cancer mortality and exposure measured as mg/m3 years and years worked. A case?control study reported that all the lung cancer cases were smokers (or former smokers) and attributed the excess to smoking. There were two mesothelioma cases among the NY State talc workers exposed to cleavage fragments of tremolite and anthophyllite, but talc is not a plausible cause because of too short latency and potential for previous asbestos exposure. The positive controls of tremolite asbestos and anthophyllite asbestos exposed workers showed excess risks of both lung cancer and mesothelioma and positive exposure? response trends. St. Lawrence, NY talc does not produce mesotheliomas in animals while amphibole asbestos does. In sum, the weight of evidence fully supports a conclusion that non-asbestiform amphiboles do not increase the risk of lung cancer or mesothelioma. ©2008 Published by Elsevier Inc. Keywords: Amphiboles; Cleavage fragments; Lung cancer; Mesothelioma; Asbestos; Non-asbestiform amphiboles; Grunerite; Talc

Jan 1, 2007

By P G. Rutherford, A W. McOnie

A volcanic sequence is described from the Golden Cross Mine, Waihi, New Zealand. The sequence includes seven lithostratigraphic units comprising flow and pyroclastic units of Coromandel Group andesite and dacite and overlying Whitianga Group dacite and rhyolite which is intruded by the Golden Cross dacite porphyry and rhyolite dykes. The sequence is mineralised and is unconformably overlain by two post-mineral units, the lacustrine Waitekauri beds and Omahine Subgroup andesite.   Detailed structural analysis of mine data has identified four deformational events (D 1-D4) and related these to the gold-silver mineralising events. Faulting was coeval with the mineralization and directly controlled the development, localisation, style and geometry of the ore shoots. Mineralization developed in competent lithologies where dilation occurred during faulting. The Empire Fault is the master shear which controlled fluid flow. Mineralised veining developed in response to tectonic pulses occurring at slightly different stages as represented by the underground Empire vein complex and the open pit vein array. The mineralising events culminated with the deposition of barren calcite veins. Post-mineral movement along the Western Boundary fault appears to have offset the orebody.

Jan 1, 1995

By William Babcock

Augered, Cast-In-Place (ACIP) piles can be an economical, reliable, versatile foundation system. They have also been a part of projects that were behind schedule and the subject of lawsuits. The ACIP pile is a specialty system that is more workmanship dependent than most deep foundation systems and is especially vulnerable to the problems and abuse of poor specifications and contract language. Many of the original specifications were based on grouting methods, and numerous misconceptions have followed the method. The Deep Foundations Institute (DFI) has been the leader in debunking the mystique that has hovered over the method and attempted to standardize the industry through publication of the manuals describing the method and how it should be inspected. DFI should be applauded for taking the lead and producing a reference document that can be used to educate the specification writers, designers, inspectors, and owners. It must be must appreciated that there have been other organizations that would not acknowledge ACIP piles as a legitimate member of the deep foundation family. Some consultants and designers have gone to the extreme of making it policy to not recommend the method for use. This presentation is one practitioner's view of the causes of problems as they can be traced back to the contractual conditions. It is intended to provide a broader and different perspective than those provided by the technical specialists. It does not necessarily reflect the position of the DFI or any of the organizations associated with the ACIP pile industry. It is intended to further the spirit of partnering on every ACIP pile project, to further the acceptance and promote the use of this unique system, for the benefit of all the parties. It should be recognized, however, that all of the participants can and do play a role in getting a project into trouble. My view is that projects that get into trouble usually have an early flaw that leads the project to the edge, and the project participants blindly follow the original mistake right over the cliff like lemmings. This instinctive reaction may be a survival tactic by going along with the group, because any one party that departs from the program or shows a position of weakness is a candidate for sacrifice.

Jan 1, 1997

By A. Tsekov, Stefan Neufeind, T. Angelov, G. Savov

"A complementary ion exchange/solvent extraction process for the recovery of copper from low-grade ores developed by Iontech Engineering Ltd. is described. It has successfully been implemented on a full-scale plant level at the Buchim Copper Mine in Macedonia, yielding a maximum copper cathode production of 2400 tonnes per year. Technical and economic aspects of three years of operational experience are comprehensively compared with the Asarel Medet copper plant in Bulgaria, which is utilizing conventional solvent extraction in the enrichment/purification step. INTRODUCTION The concentration and separation of copper from primary leachates is one of the key operations in the hydrometallurgical processing of oxide ores (Langner, 2011). Conventionally, this basic operation is conducted by submitting the pregnant leach solution (PLS), with a 1–5 g/L Cu content, from the initial sulfuric acid leach to a solvent-extraction (SX) process in which copper reports to the organic phase (see Figure 1). After phase separation, the metal is stripped from the extractant/diluent mixture employing sulfuric acid to furnish a concentrated metal solution, usually containing 40–50 g Cu/L. The final products of the overall process are copper cathodes, which are obtained from a terminal electrowinning step.Although considered as “technology of choice”, SX to date is still suffering from several drawbacks, such as the risk of poor phase disengagement and the high capital costs of solvent-extraction plants. Especially, the processing of leachates with lower copper tenors (< 1 g/L) is often economically less attractive. As a result, tremendous efforts have been dedicated to the evaluation of alternative technologies to address these challenges."

Jan 1, 2015

By Gregory Poole

With access to the World Wide Web, many resources are readily available for improving claim reports. With a little time spent on line, a more thorough report can be created. Claimants will accept the conclusions of a report more readily when they can view support information on their own computer, particularly when the support information is not just from blasting related web sites. Some suggested resources are discussed including aerial pictures, local tax maps, topographical maps and home repair web sites. This paper provides suggestions for tracking down support information on the web and information on how to properly reference this information. Case studies of several claim investigations are presented. These are some examples of how a little time spent online provided clear and convincing evidence to support the conclusions of the investigation.

Jan 1, 2006

Detailed mineralogical investigation of a tailing sample from the Juno plant circuit at Tennant Creek was carried out to determine the nature of the unrecovered bismuth and whether any possibility existed for improving bismuth recovery. The investigation showed that the Ibismuth was present in a complex mixture of Bi-Pb-Ou-Se-S minerals (termed &quot;bismuthinite&quot;), of which about 74 per cent was locked (mainly with magnetite) and 26 per cent was liberated (18 per cent in the minus 7 &#181;m slime). The results suggested that attention should be directed to both finer grinding and improved flotation of slime &quot;bismuthinite&quot;, and testwork carried out by Peko Mines N.L. on the basis of these recommendations led to a significant improvement in bismuth recovery.Detailed mineralogical investigation of two Juno concentrates was carried out to determine the nature of the selenium present and whether any possibility existed for improving the selenium grade. The investigation indicated that virtqally all the bismuth, selenium, and lead was present in &quot;bismuthinite&quot;, which showed a composition range of 32-82 per cent Bi, 0-42 per cent Pb, 0-24 per cent Se, and 5-18 per cent S. Differences in the Bi/Se ratios of the two concentrates could be attributed to different average Bi/Se ratios of the constituent &quot;bismuthinite&quot;, and the relatively low selenium grade of the &quot;bismuthinite&quot; precluded the possibility of obtaining a high grade selenium concentrate with high selenium recovery.However, differential flotation and/or low intensity magnetic separation to remove chakopyrite, and magnetite, the main diluents of the concentrate, could be expected to upgrade the selenium content byup to 80 per cent (relative) and .festwork carried out by Peko Mines N.L. on the basis of the recommendations of the mineralogical investigation confirmed that depression of chalcopyrite in the flotation circuit could produce significantly improved selenium grades.These investigations illustrate the application of mineralogy to the practical problems of improving plant performance. Mineralogy has an important role to play in providing quantitative data on which the metallurgist can evaluate plant performance and base a programme of metallurgical testwork, and early mineralogical investigation of feeds, concentrates, middlings, and tailings can lead to the avoidance of much abortive and expensive metallurgical testwork.

Jan 1, 1974

By Y. L. Sun

The feasibility of using the ultrasonic wave attenuation method for measuring in-situ stress is examined theoretically and experimentally. The theoretical analyses show that for a given rock type the relation between stress and attenuation coefficient ratio can be approximated closely by second-order polynomials. Combining the elastic and statistical theories, the magnitude and direction of the existing principal stresses can be predicted by using the relations between stress and attenuation coefficient ratio obtained in the calibration of core specimens. Several experiments are conducted in the laboratory on two types of rock. The experimental study consists of two parts: the attenuation-coefficient measurements in core specimens under uniaxial stress and the attenuation coefficient measurements in boreholes drilled through blocks of sandstone and limestone subjected to uniaxial compressional stress. Compressional waves are used exclusively in the measurements.

Jan 1, 1989

By J Kelly, C Kelsey

The Autogenous Kelsey Axial Displacement (KAD) mill is essentially a short retention time centrifugal mill, designed to effectively harness extraordinarily high concentrations of input energy for efficient particle size reduction. The mill which has an operating duty band extending from primary to ultra-fine also has the unique capacity to generate fine and ultra-fine products from single stage size reductions of either coarse or fine mineral feeds, in both wet or dry operating modes. This paper covers developments following a recent optimisation programme which confirmed that mill shell speed and the velocity differential between the shell and the rotating internal disc assembly tips could be optimised in relation to specific energy for a given feed rate and feed size providing the product size remains constant. Subsequent test-work further demonstrated the versatility of the mill with duties ranging from the removal of surface contamination associated with heavy mineral concentrate particles to the production of premium ultra-fine talc, from a single stage of size reduction. Open circuit grinding of a rougher gravity concentrate to liberate gold ahead of leaching also highlighted the scope for the application of low cost KAD milling for a range of hydrometallurgical feed preparation duties, which involve fine and ultra-fine grinding.CITATION:Kelly, J and Kelsey, C, 2013. Advanced media-free fine and ultra-fine grinding - The Kelsey axial displacement mill, in Proceedings MetPlant 2013 , pp 152-161 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 15, 2013

By Verne E. Hooker

Stress-relief techniques and instrumentation have been developed through many years of research in the Federal Bureau of Mines and successfully used to determine the in situ state of stress in rock. This paper describes the drilling equipment and accessories for use with the Federal Bureau of Mines three-component deformation borehole gage. Operation and calibration procedures for the deformation gage are discussed in detail. Site selection and overcoring procedures are included to provide a complete working knowledge for surface or underground applications.

Jan 1, 1974

By L. M. Kaas

Production planning techniques, particularly a production scheduling model are proposed for use in taconite mining in Minnesota. Applications of the scheduling model, on a two-year mine plan, which evaluates the equipment involved, are detailed. Data and tables are included. INTRODUCTION Fifty years ago Walter Swart, a mining engineer investigating the Minnesota taconites for the Jackling interests, made this report: "There is no doubt in my mind that this taconite mining is a game worth playing and that it can be played to a successful finish. It seems now only a question of men, money, methods and details."&apos; The prosperous industry envisioned by Swart and other taconite pioneers is today a reality. Its growth has been spurred by technological advances in mining and beneficiation, depletion of natural ore reserves, and improvement of the economic climate. However, the massive problems that were solved to make this development possible are only a foreshadowing of the questions of "men, money, methods and details" that will be encountered in the future. The increasing demands for higher quality taconite pellets have already forced producers to examine better methods of quality control for their operations. THE NEED FOR PRODUCTION SCHEDULING The maintenance of fairly constant crude ore characteristics is of major importance to mill quality control. Through careful mixing of ore from storage bins, the concentrator staff can partially reduce the deviations of the feed analysis from the analysis desired. However, the limited effectiveness of bin mixing systems has caused some mining companies to utilize large capacity blending piles to reduce grade variations. Although the analysis of material being reclaimed from such a pile is relatively uniform, raw materials still must be scheduled from the mine into the pile in such a manner that the average analysis of all material is close to the feed analysis prescribed by the mill. PRODUCTION SCHEDULING MODEL Minnesota taconite mining companies have used three analyses to estimate how a certain ore will react to concentration. These factors are the crude magnetic iron content of the ore, the iron content of the plant concentrate produced from the ore at a standard grind, and the grindability index of the ore. The actual laboratory tests used to determine these factors have been described by Apuli.2 These data are obtained from analysis of diamond drill cores, and are the established criteria used by mine planning engineers to formulate taconite production schedules. Variations in the grade of mine output should be controlled by any production scheduling system. However, to be truly practical, production scheduling methods must also consider many of the less tangible variables that affect mine operation. These include pit layout, available equipment, and ownership of ore leases. The number and scope of the variables inherent in this type of mine planning suggested that a computer simulation could be used to solve the problem. The preparation of information for use with a computer simulation program was the initial phase of this project. Meaningful data was developed from logs of diamond drill cores. Analyses were related to their respective areas of influence by means of mine maps, Fig. 1. The three assay variables and tonnages for each area were punched on cards. In addition to these values, a location code number was punched in the first eight columns of the cards. This code is explained as follows: Column 1 Bench number Column 2 Quadrant location as determined by mine reference lines Columns 3-5 East-west coordinate Columns 6-8 North-south coordinate The heart of any simulation techniques is a well engineered mathematical model. To develop a model for taconite production scheduling, the relationship between the three assay variables had to be established. Because changes in each analysis factor affect the mill circuits in different manners, a weighting system was used to determine the relative im-

Jan 1, 1967

By R. Allington, G. Walton

The approach has been applied with success to the restoration of chalk workings in southern England, and research and trials relating to restoration blasting and the replication of limestone dale landforms have been undertaken. An essential prerequisite for application of the technique is rigorous geomorphological analysis of the locality to ensure that final quarry landforms are consistent with the local geomorphological and landscape setting. It is always important to ensure compatibility of the final landform with the intended after-use, and to achieve this it is also essential that such restoration schemes have a sound geotechnical basis. A disadvantage of the approach is that final slopes tend to be flatter, especially in weaker strata where natural slopes are not steep; the implications for reserves may be unacceptable, particularly in quarry extensions

Aug 1, 1994

By James Tarr, Matthew Eichler, Brent Tardif

ANFO was being used as one of the blasting agents on a construction site in New England. Groundwater was encountered in numerous blast holes. The blasting contractor was employing typical explosives loading procedures for wet conditions. An abutter to the project complained that blasting caused her well water to have an odd taste and smell. Through testing, it was determined that there were hydrocarbons and nitrates in the well water. Several days later a second neighbor complained of foul tasting water; again it was determined that hydrocarbons and nitrates were present.

Jan 1, 2003

By S. R. Dindarloo

Although blasting is one of the most widely used methods for rock fragmentation, it has a major disadvantage in that it causes adjacent ground vibrations. Excessive ground vibrations can cause a wide range of problems, from nearby residents complaining to ecological damage. Prediction of blast-induced ground vibration is essential for evaluating and controlling the many adverse consequences of surface blasting. Since there are several effective variables with highly nonlinear interactions, no comprehensive model of blast-induced vibrations is available. In this study, the support vector machine (SMV) algorithm was employed for prediction of the peak particle velocity (PPV) induced by blasting at a surface mine. Twelve input variables in three categories of rock mass, blast pattern, and explosives were used for prediction of the PPV at different distances from the blast face. The results of 100 experiments were used for model-building, and 20 for testing. A high coefficient of determination with low mean absolute percentage error (MAPE) was achieved, which demonstrates the suitability of the algorithm in this case. The very high accuracy of prediction and fast computation are the two major advantages of the method. Although the case study was for a large surface mining operation, the methodology is applicable to all other surface blasting projects that involve a similar procedure.

Jan 1, 2015

By Jorge Navarrete

La Corporación Nacional del Cobre de Chile produce cobre y otros subproductos a través de sus yacimientos y líneas de producción como las pirometalúrgica, hidrometalúrgica y biohidrometalúrgica. En este sentido, el presente texto señala la implantación de un LIMS para la industria minera de cobre. LIMS es una abreviatura genérica para los software de Administración de Información de Laboratorio, cuyo objetivo es relacionar la Informática, Quimiometría y Calidad.De forma que cumpla con los objetivos de adquisición y gestión de la información de pesaje, muestreo y análisis químico producida por diferentes áreas, tanto internos como externos y unidades funcionales.

Jul 17, 2000

By K. Lombard

"‘Roof support awaiting time’ (RSAT) is a term used at Goedehoop Colliery’s Simunye Shaft to describe the potential production time lost due to the continuous miner (CM) standing idle waiting for roof support to catch up. Investigations revealed that in 2013, Simunye Shaft had approximately1400 hours of RSAT, which suggests that the mine could have potentially produced an additional 280 000 t of coal. This project consisted of two parts. Firstly, the causes of the high RSAT and means to improve the situation were investigated. Secondly, as insisted by mine management, the CM cutting sequence was investigated as a possible cause of high RSAT. Machine-related challenges due to the roofbolter installing support too slowly, geological conditions (mostly hard roof conditions and slips),logistical challenges pertaining to the CM cutting sequence, man-related challenges related to operator fatigue, re-support, operator inexperience, and the absence of support targets were identified as main contributors to RSAT. Furthermore, results showed that the roofbolters in the sections at Simunye Shaft are slower than the CMs. A target of 28% reduction in RSAT was set. Experts from Kennametal and Fletcher were consulted to find solutions for the identified causes. In total, eight solutions for RSAT were identified, but the solution that contributed most significantly to reducing RSAT was to use hard roof drill bits as a standard product at Simunye Shaft. Calculations showed that by using hard roof drill bits, RSAT can be reduced by 43%, which is more than the specified 28% target. The cutting sequences at Kriel, Greenside, and Simunye Shaft, togetherwith three newly developed cutting sequences, were simulated using the UCMS (Underground Coal Mining Simulation) program. A re-aligningprinciple was incorporated into the newly developed cutting sequences toalign the cutting sequences to general support work and to reduce RSAT. A decision matrix revealed that a cutting sequence in which boxing takesplace in R3 (third road to the right of the belt road) and in which the re-aligning principle has been incorporated will be the best option for Simunye Shaft. The recommended cutting sequence will lead to a 5% increase in production.The work presented in this paper was carried out as partial fullfilment for the degree BEng (Mining Engineering)"

Jan 1, 2015

By Bernard Woolley

The history of the use of calcium aluminates in mining is discussed including a review of very rapid hardening concretes, anchoring using cement capsules and pumped ground control systems. Specific reference is made to the long term performance of highly abrasion resistant orepass lining in South Africa and the use of rapid hardening materials for a range of applications in Australian coal mine where water infiltration creates difficulties or where rapid repair or return to service is required. The topics covered in detail are, high strength abrasion resistant concretes with a 20 year, 30 million ton ore pass life. Rapid reinstatement of wet and worn roadways using mineral dewatering and rapid roadway rebuild solutions, all in I maintenance shift. The different applications are illustrated using examples from operating mines.

Jan 1, 1997

The failure of a seal in an underground coal mine can have devastating consequences. Traditionally seals have been constructed as flat walls. Large hydraulic dams, on the other hand, are constructed as concave arches. This paper presents an initial analysis of the potential strengthening of seals by concave construction as well as the impact of additional cost in terms of labor and material. A simple finite element analysis of three-dimensional solids under uniform loading allows comparisons between the strength of a flat wall and a curved arch. The models are examined for reasonable behavior and displacements at 20, 50, 100, and 200 psi loads.

Jan 1, 2007