Search Documents

By Satu Jyrkönen

A single-particle laminar-flow technique was used to study oxidation of four synthetic nickel mattes, which were screened into three size fractions, Experimental conditions were: reaction gas from N2 - 21 to 75 vol-% O2; gas preheating temperatures ranging from 500 to I 100'C. The four mattes were synthesized so that Ni/Cu ratios of I and 10 were obtained with high and low iron contents. Chemical analysis of the particles was used to determine the oxidation degree of the materials, and optical and scanning electron microscopy were used to detect their morphology, internal composition and structure. The best sulfur removal from the synthetic nickel mattes was achieved under the most oxidizing conditions with the finest size fraction. The matte with Ni/Cu = 1 and high iron content was found to be most reactive. The least reactive matte was with Ni/Cu = 10 and low iron content; the coarse fraction particles did not react at all under the conditions studied.

Jan 1, 1996

By W. G. Stevenson

The centennial celebration of the AIME provides an opportunity to review some aspects of developments in mineral exploration since 1871 and to reflect on the changes that have occurred. During this period seven Factors have fundamentally altered the procedures, techniques and philosophy of mineral exploration. Although most of these developed gradually, and unheralded, they have drastically altered the art of exploration and discovery. 1. ADVANCES IN MINING AND MILLING The development of huge shovels, draglines, trucks and track-mounted drills, to replace the wheelbarrow and single Jack has drastically expanded the rate of production for both underground and surface mining. The development of selective flotation has had a far-reaching affect on mineral exploration and has made it possible to extract metals from the metallurgically complex deposits discovered years before. These developments have reduced the costs of mining and treatment, and have transformed material into ore that was considered waste one hundred years ago. These advances have permitted exploration for progressively lower grade and larger mineral deposits.

Jan 1, 1971

By M. Kinnunen

Handling of municipal solid waste (MSW) and control of its potential resources is becoming increasingly important in modern society. The OECD (Organization for Economic Co-operation and Development) average on municipal waste produced in 2003 was that of around 570 kg per inhabitant. In European Union countries around half amount is of MSW landfilled. In Finland still 88% of MSW was landfilled in 2004. Since incineration reduces MSW volume significantly while producing heat energy, it has become one of the most common waste handling techniques. The shortcoming of incineration is however, that incinerated MSW is often not pre-sorted and it produces slags and ashes as side streams from which recovery of metals is difficult. This paper looks into possibilities of scrap metal recovery for recycling from municipal solid waste incineration (MSWI) bottom ash. In order to do that, a flow sheet of physical separation methods was developed and tested with Finnish rotary furnace MSWI bottom ash. In addition, an empirical model for estimation of the recoveries of scrap metals with physical separation methods for treatment of MSWI bottom ash was developed. According to the results of this study, for 1 Mt of incinerated MSW with 30% mass reduction, a minimum resource potential of 100 kt for magnetic metal scrap of roughly 24 % grade and about 19 kt of non-magnetic metal scrap of roughly 65 % grade. In other words, 57 kg magnetic scrap and 12 kg non-magnetic scrap per inhabitant at the mentioned grades, respectively. Although wide variations of parameters affect the MSWI bottom ash quality, it can be said that a considerable amount of metals is drained into MSWI bottom ash. Results of this study show that from MSWI bottom ash significant material streams metal scrap can be reintroduced into the resource cycle which would otherwise be lost.

Jan 1, 2014

By N. C. J. Dempers, J. A. L. Parker, R. A. Wildenboer

More than half of global cobalt reserves are located in the Southern African Copperbelt, stretching over the northern tip of Zambia and southern area of the Democratic Republic of Congo. In these areas, cobalt is not typically produced as a primary product but as a byproduct of copper production. Ores from this region often contain uranium, which is readily leached under typical copper leach conditions and enters the process. Uranium does not pose a challenge to copper production, but it becomes a significant problem when it follows cobalt to the cobalt precipitation process and results in unacceptably high levels of U in the final Co product. This paper evaluates the existing process technologies that can be used to remove uranium from cobalt-bearing process streams, including phosphate precipitation and ion exchange. Advantages and disadvantages of the uranium removal processes are discussed, and important design considerations are highlighted.

Jan 1, 2023

By Siavash Mahvelati, Alireza Kordjazi, Joseph Thomas Coe

Deep foundations are often constructed as end bearing members with a significant amount of their capacity derived from bedrock. Sites with highly variable bedrock conditions therefore present a unique challenge when attempting to estimate the design elevation of deep foundations. Typical subsurface characterization techniques such as drilling, standard penetration testing (SPT), and cone-penetration testing (CPT) may fail to adequately establish top-of-rock elevation in geologic settings prone to karst and/or significant amounts of residuum, saprolite, and deformed bedrock. Seismic surface wave geophysical methods have been increasingly used to map bedrock topography in such settings. However, the current standard of practice for these methods introduces resolution limitations in spatially variable subsurface conditions due to averaging effects from the analytical framework used to process the acquired data. This study explores the use of a tomographic approach with full waveform inversion (FWI) to map top-of-rock elevations at a numerically simulated site representative of highly variable bedrock topography. Comparisons are made with seismic refraction (SR) and a dispersion-based multichannel analysis of surface waves (MASW) approach as more commonly used in geophysical subsurface investigations. The results highlight that FWI provides a superior estimate of top-of-rock topography than SR and MASW at a cost of a significant increase in the required computational resources and time.

Sep 8, 2021

By Siavash Mahvelati, Alireza Kordjazi, Joseph Thomas Coe

Deep foundations are often constructed as end bearing members with a significant amount of their capacity derived from bedrock. Sites with highly variable bedrock conditions therefore present a unique challenge when attempting to estimate the design elevation of deep foundations. Typical subsurface characterization techniques such as drilling, standard penetration testing (SPT), and cone-penetration testing (CPT) may fail to adequately establish top-of-rock elevation in geologic settings prone to karst and/or significant amounts of residuum, saprolite, and deformed bedrock. Seismic surface wave geophysical methods have been increasingly used to map bedrock topography in such settings. However, the current standard of practice for these methods introduces resolution limitations in spatially variable subsurface conditions due to averaging effects from the analytical framework used to process the acquired data. This study explores the use of a tomographic approach with full waveform inversion (FWI) to map top-of-rock elevations at a numerically simulated site representative of highly variable bedrock topography. Comparisons are made with seismic refraction (SR) and a dispersion-based multichannel analysis of surface waves (MASW) approach as more commonly used in geophysical subsurface investigations. The results highlight that FWI provides a superior estimate of top-of-rock topography than SR and MASW at a cost of a significant increase in the required computational resources and time.

Oct 1, 2021

By Howard Lum, Sergio Valles, John Bednarski, Gordon Enas, Jay Arabshahi

"Water drawn from the Sacramento-San Joaquin Delta provides water supply to 66 percent of California’s population and supports the state’s agriculture industry. The existing through-Delta water system is outdated and unreliable with environmental risk to some fish and wildlife species. The Bay-Delta Conservation Plan (BDCP) has been established to environmentally retrofit and modernize California’s water delivery system through the Delta by restoring habitats, constructing new diversion points in the north Delta and providing a means to transport water supplies under the Delta, rather than through sensitive natural channels.Under BDCP, the Delta Habitat Conservation and Conveyance Program (DHCCP) has developed several alternatives to convey water from the Sacramento River in the north to the existing pumping facilities in the south Delta through an isolated conveyance system. The new conveyance system would become an integral part of the State Water Project (SWP) and the federal Central Valley Project (CVP) by transporting water to the export pumping plants for each of these projects. The DHCCP is managed by the California Department of Water Resources (DWR), while state and federal water contractors provide technical support to the program.The initial conceptual study efforts on the overall program commenced in 2007 and examined various options for the proposed conveyance system. Several conveyance alternatives were analyzed at that time. The Conceptual Engineering Report published on Oct. 1, 2013 identified the modified pipeline/tunnel option (MPTO) as the preferred alternative to be included in the BDCP environmental documents. MPTO includes three river intakes and pump stations along the Sacramento River, various sizes of pipelines and tunnels, junction structures and two forebays that are capable of delivering up to 4 million gpm (9,000 cfs) from the Sacramento River to the SWP and CVP. The river intakes are located near Hood in Sacramento County approximately 64 km (40 miles) from Clifton Court Forebay (CCF) in Contra Costa County. This route would cross portions of Sacramento, San Joaquin and Contra Costa counties. Figure 1 depicts the configuration of the MPTO alternative."

Apr 1, 2016

By Thomas M. Barczak

The effect of load rate on the load-carrying capabilities of wood cribs is investigated in this Bureau of Mines study. The modulus of deformation (stiffness) of wood crib blocks has been shown to increase with increases in rates of load application, causing larger load reactions for increases in convergence rates. Since wood cribs are tested in the laboratory at convergence rates that are orders of magnitude faster than typically would occur underground, wood cribs tested in the laboratory will react larger loads than the same cribs would react underground for the same displacement. Tests conducted in the Bureau's mine roof simulator on green wood crib blocks indicate that the increase in stiffness for increasing load rates diminishes at displacement rates beyond 0.1 in/min, making crib load nearly independent of load rate for rates faster than 0.1 in/min. Seasoned wood specimens were not as con-sistent in load-rate dependency. Some possible explanations of observed load-rate behavior on wood crib specimens are also postulated in this paper.

Jan 1, 1988

By G. Asai

The Bureau of Mines has been engaged in a program to increase the utilization of chromium by providing samples to individuals and institutions requesting chromium for research investigations. This report consists of a tabulation of the disposition of chromium samples distributed from July 1953 through June 1961; 109 requests for chromium were answered by providing chromium as electrolytic plate, powder, or wrought forms. The demand for samples reached a peak in fiscal year 1959 and declined to a relatively low level in fiscal year 1961. The largest number of requests came from individuals engaged in mechanical property studies; there were also many requests from those concerned with vaporized metal and physical properties studies. Most noteworthy application for chromium was the experimental use of the radioactive form, Cr61 in radiotherapy of cancer.

Jan 1, 1964

By G. Asai

The Bureau of Mines has been engaged in a program to increase the utilization of chromium by providing samples to individuals and institutions requesting chromium for research investigations. This report consists of a tabulation of the disposition of chromium samples distributed from July 1953 through June 1961; 109 requests for chromium were answered by providing chromium as electrolytic plate, powder, or wrought forms. The demand for samples reached a peak in fiscal year 1959 and declined to a relatively low level in fiscal year 1961. The largest number of requests came from individuals engaged in mechanical property studies; there were also many requests from those concerned with vaporized metal and physical properties studies. Most noteworthy application for chromium was the experimental use of the radioactive form, Cr[51], in radiotherapy of cancer.

Jan 1, 1964

By Gerald Edmunds

THE liquidus line on the phase diagram for temperature versus composition of a binary alloy system, representing the boundary between the homogeneous melt and the heterogeneous melt plus solid, besides showing the minimum casting temperature, is useful in determining eutectic compositions and the presence of phase changes such as peritectic transformations and intermetallic compound formation. The liquidus often is determined by the cooling curves of thermal analysis, but supercooling frequently occurs, so that the temperature values are low. An alternative method, the one employed here, consists of determining the com- position of samples of the melts from heterogeneous alloys that are at equilibrium. With meticulous attention to fundamentals, this method is capable of yielding values limited in precision only by the temperature control and measurement and analyses. APPARATUS By starting, on the one hand, with a supersaturated solution and allowing the excess solute to precipitate, and on the other hand with an undersaturated solution and allowing more of the solute to be dissolved, both processes being carried out at the same temperature, equilibrium may be said to have been approached from both directions; that is, from above and from below. If the analyses show the solutions to contain the same fraction of solute when equilibrium has been approached from above and from below, one is assured that equilibrium has been reached in both determinations. In order to carry out such determinations, it is necessary to have equipment for obtaining and maintaining the proper temperatures; for holding the melt, measuring its temperature, and stirring, sampling and analyzing it. The present work required temperatures from 420° to 900°C. The equipment consisted of: A furnace, which was a vertical alundum tube, 1 ¾ in. diameter inside and 18 in. long, wound with Nichrome resistance wire, surrounded by a 3-in. i.d. alundum tube wound for 5 in. of length near each end, for compensation of end losses. This muffle was contained in an iron shell with Transite end plates, the intervening space being packed with Sil-O-Cel. The outside dimensions of the furnace were 12 in. in diameter by 18 ½ in. in height. Heating current was supplied by three independent variable-voltage transformers (Variac), one connected to each end compensator winding and manually controlled, and one connected to the main winding through a series resistance of 5 ohms. This resistance was short-circuited for

Jan 1, 1944

By William R. Webster

I have continued the investigation of the Pottstown Iron Com pany's basic Bessemer keel plates on the line referred to in my paper of last October (Trans., xxi., 766)) and have added a study of the hardening effects of sulphur, which were not taken into account at that time. The results are so encouraging that I now give them in full. For some months we have graded all the steel at these works by the table given in my former paper, and checked the grading by the forging-tests as described in the paper of Mr. Joseph Hartshorne, read at the same meeting (Trans., xxi., 748). The steel thus graded was bloomed for the plate orders. Then one slab was rolled into a plate for the order, and a tension-test was made of this plate. By the result of this tension-test we were guided in rolling the balance of the heat. Out of several hundred heats graded in this manner, 95 per cent. met the requirements of the orders in every respect, and were accepted; but these results will no doubt be improved upon, when the influence of sulphur is also considered.. The hardening effect of sulphur seems to be about 500 pounds per each .01 per cent. of increase. In the table accompanying the pres ent paper, the ultimate strength with .06.5 per cent. sulphur agrees with the old table where sulphur was not considered; that is, for all steels with less than .065 per cent. sulphur we now get lower re sults, and for those with more sulphur, higher results. Making this allowance for sulphur, the assumed ultimate strength of a 3/8-inch plate of pure iron is reduced from 38,000 pounds per square inch to 34,750 pounds. With this as a basis, I have constructed my new table, giving each of the elements, carbon, phosphorus and manganese the same hardening effect as before, to wit : Carbon is credited with a constant effect of 800 pounds per each, 0.01 per cent. Phosphorus shows greater effect in high-carbon than in low-carbon steels. For 0.07 and 0.08 C, it has about the same effect as carbon, that is, 800 pounds for each .01 P. This increases to 1500 pounds per .01 P in 0.15 C steel, or nearly twice the effect of carbon. This

Jan 1, 1894

By R. W. Harper, M. C. Fuerstenau, J. D. Miller

Data were obtained with hematite with octyl hydroxamate and oleate as collectors to determine the mechanism of collector adsorption and also to establish the roles that conditioning time and temperature assume in this system. The presence of hydroxy complexes of iron are apparently necessary for chemisorption of collector to occur, and it appears as if extended conditioning times and elevated temperature promote greater dissolution of the mineral and hence greater concentrations of hydroxy complexes. Data were also collected with two natural hematitic ores. With one ore that was ground to 70% - 15u, an addition of 0.4 lb per ton hydrox-amate resulted in a final concentrate recovery of 86% at a grade of 64% iron. Satisfactory concentrate grade could not be obtained with fatty acid under these conditions. The effect of conditioning time prior to the addition of collector was also examined with another ore. When the ore was conditioned for 3 min, 19% of the iron was recovered in the concentrate at a grade of 67% Fe. With a conditioning time of 7 min, 73% of the iron reported to the concentrate at a grade of 62% Fe. These products were obtained with an addition of 0.2 lb per ton hydroxamate. This ore also responded well to flotation with fatty acid. The use of potassium octyl hydroxamate as a collector for iron oxide has been the subject of an earlier study.1 From this initial study, it was suspected that hydrolysis of surface ferric iron was involved in collector adsorption. More recent work in other systems has shown that slight mineral dissolution, followed by hydrolysis of cations common to the mineral lattice, is apparently necessary, and that adsorption of these hydroxy com- plexes probably occurs prior to the adsorption of collector. In view of these facts, work has been continued on the hydroxamate-hematite and oleate-hematite systems to gain better insight into the mechanisms of collector adsorption on iron oxide. Microflotation experiments in conjunction with infrared analysis were used in this regard. In addition it was felt necessary to establish more clearly the responses that can be obtained from natural ores when hydroxamate is used as collector as compared to those obtained when fatty acid is used. Experimental Materials and Techniques Pure potassium oleate, potassium octyl hydroxamate, synthesized from hydroxylamine hydrochloride and methyl octanoate, and a distilled Tall Oil were employed as collectors. Conductivity water was used in the

Jan 1, 1971

By G. Derge, Lo Ching Chang

The chemical and physical propertties of slag systems are of special interest to metallurgists, for nearly all metals are in contact with molten slags during the primary reduction from their ores and then during the subsequent refining and alloying processes that determine their ultimate use. These processes are carried out at high temperatures and involve such complex chemical systems that funda-mental scientific knowledge of the Properties and behavior of these slags is inadequate. Various hypotheses have been Proposed to explain known slag characteristics. The commonest of these regard the molten slag as constituted of compounds that are dissociated in varying degrees into their constituent oxides, as illustrated by Schenckl and the recent Papers of Chipman and co-authors. Another proposal is that these compounds dissociate by com-plete6 or partial ionization, the evidence for which has been reviewed by Martin and Derge.? whatever hypothesis is favored, the exact formulation of these compounds is incomplete. It is based on three principal types of information: 1. Studies of solidified 51% samples by X ray diffraction, petrography, and similar methods that can be used at room temperature. The correlation of this information with the high-temperature properties of the molten slag is uncertain. 2. Studies of slag-metal equilibria, which have the advantage of providing observations on the molten slag at high temperature. However, even these data present problems of interpretation because they require a complete knowledge of the metal phase. 3. Direct measurements of properties of molten slag at the temperature of greatest metallurgical interest. Viscosity, electrical conductivity, specific heats, and similar properties have been measured, but the data of this type are widely scattered and frequently difficult to interpret. Additional direct measurements of properties of molten slag that can be interpreted in terms of chemical behavior are required, and this paper shows that the standard physical-chemical measurement of reversible electrode potentials, which measure the activity of specific constituents, is a fruitful source of such information. The purpose of this investigation, therefore, was to find an electrode combination that would yield reversible electromotive force measurements when dipped into the molten slag to be studied. Slags of the systems cao-sio2 and cao-120,-SiO2 were chosen for study because graphite containers could be used and the data could be correlated with those for viscosity, conductivity, and other proper-

Jan 1, 1948

By G. Derge

The chemical and physical propertties of slag systems are of special interest to metallurgists, for nearly all metals are in contact with molten slags during the primary reduction from their ores and then during the subsequent refining and alloying processes that determine their ultimate use. These processes are carried out at high temperatures and involve such complex chemical systems that funda-mental scientific knowledge of the Properties and behavior of these slags is inadequate. Various hypotheses have been Proposed to explain known slag characteristics. The commonest of these regard the molten slag as constituted of compounds that are dissociated in varying degrees into their constituent oxides, as illustrated by Schenckl and the recent Papers of Chipman and co-authors. Another proposal is that these compounds dissociate by com-plete6 or partial ionization, the evidence for which has been reviewed by Martin and Derge.? whatever hypothesis is favored, the exact formulation of these compounds is incomplete. It is based on three principal types of information: 1. Studies of solidified 51% samples by X ray diffraction, petrography, and similar methods that can be used at room temperature. The correlation of this information with the high-temperature properties of the molten slag is uncertain. 2. Studies of slag-metal equilibria, which have the advantage of providing observations on the molten slag at high temperature. However, even these data present problems of interpretation because they require a complete knowledge of the metal phase. 3. Direct measurements of properties of molten slag at the temperature of greatest metallurgical interest. Viscosity, electrical conductivity, specific heats, and similar properties have been measured, but the data of this type are widely scattered and frequently difficult to interpret. Additional direct measurements of properties of molten slag that can be interpreted in terms of chemical behavior are required, and this paper shows that the standard physical-chemical measurement of reversible electrode potentials, which measure the activity of specific constituents, is a fruitful source of such information. The purpose of this investigation, therefore, was to find an electrode combination that would yield reversible electromotive force measurements when dipped into the molten slag to be studied. Slags of the systems cao-sio2 and cao-120,-SiO2 were chosen for study because graphite containers could be used and the data could be correlated with those for viscosity, conductivity, and other proper-

Jan 1, 1948

By Rainer Hüsken

Over the last decades long BOF campaign lives have successfully been established due to improved quality of the refractory material and due to intensive use of slag splashing. On the other hand, steelmakers are more and more faced with elevated phosphorous contents in the hot metal. This phenomenon is a global tendency caused by the increasing pressure to utilize cheaper iron ore sources. In India, iron ore sources have traditionally elevated phosphorous contents. The phosphorous removal challenge calls for using bottom stirring at the BOF converters, as these combined technology of top oxygen blowing and inert gas stirring through the bottom, helps significantly to improve bath mixing and thus in shifting the process towards the optimum metallurgical equilibrium conditions. All this is common knowledge and daily business in the steelmaking shops all over world. Unfortunately, focusing on a long BOF refractory campaign by means of slag splashing and maintaining optimum conditions for high efficient bottom stirring are naturally conflictive aims. Applying slag splashing causes unavoidable bottom built-up which in turn covers or even blocks the bottom tuyeres. Most of the steelmaking shops today are either operating slag splashing without bottom stirring or bottom stirring without slag splashing. Some are trying slag splashing with bottom stirring but mostly only for a certain short period of the whole campaign. Baoshan Meishan Steel is an integrated steel plant, located in Nanjing (China). The plant is operating two BOF shops (3x 150t and 2x 250t), producing various steel grades. Because of the iron ore source used, the hot metal phosphorous content is rather high with up to 2,000 ppm. In order to achieve low phosphorous contents in the molten steel below 200 ppm, Meishan uses the TBM (Thyssen Bottom Metallurgy) bottom stirring technology in both of their steel plants, successfully applying slag splashing and efficient bottom stirring for campaigns up to 10,000 heats. This paper describes the operation procedures, strategies, and the maintenance concept established at Meishan Steel which is suitable to meet both conflicting targets at the same time.

Jul 30, 2018

By Neillm Alastair S.

"This paper looks at what has happened in the past decade in the rare earth industry, particularly for those companies outside China trying to develop alternative projects to the Chinese dominated supply chain. The rare earth industry has gone through a metamorphosis over the past decade. The industry was basically unknown outside China until overnight it became the next hot topic on the financial streets of Canada and Australia. Suddenly various junior miners shifted from uranium and other out-of-favor commodities to rare earths as funds were easy to access from an investment community that did not understand the complexities of the space. The initial funding was done on traditional junior mining metrics of grade and deposit size. This has morphed over time to:1) Lights versus heavies2) Making a concentrate3) The importance of separation4) Off-take agreementsAt the peak of the market frenzy certain flagship operations were built using the “Not Made in China” moniker. Unfortunately certain errors were made during implementation, which are finally coming to the surface and making the rest of the pack wondering what will happen next. A review and update of some of the mistakes made and lessons learned will be discussed.BACKGROUNDAbout ten years ago awareness started to form around the rare earth industry and various groups recognized that because of the closure of Molycorp, Mountain Pass, and the dominance of China, there was a risk of uncertainty of reliable supply. This was not news for those active in the industry like Rhodia (now Solvay), the Japanese, South Koreans and other key consumers but to others it was like a light went on and rare earths became the new “.com” trend for investment banks, investors and some mining companies looking for the next hot topic.In the late 1990’s Molycorp accounted for around 20-25% of the world’s supply of rare earths, mostly lights (La, Ce, Pr and Nd), with small amounts of heavies from other sources. Then environmental issues forced the closure of the operation at Mountain Pass. Within six months China had increased production to plug the gap in supply. Around that time China was developing a strategy to leverage their position in rare earths and implemented a series of regulations to increase the value added component of rare earths inside China."

Jan 1, 2016

By Srijit Bandyopadhyay, Aniruddha Sengupta, G. R. Reddy, Raj Banerjee

The objective of the present endeavor is to compare the performance of a pile raft system in foundation sand subjected to lateral loads. To study the behavior of pile raft system in sand a laboratory test was conducted on small scale model foundation system. The raft and pile was modeled by square concrete foundation of 250 mm x 250 mm x 15 mm in length, breadth and thickness and 25mm diameter and 250mm long circular pile located at the center of the raft. The system was tested under static lateral loads of 6.25N, 12.5N, 18.75N and 25 N respectively resting on dry Kasai River sand. A vertical surcharge pressure of 1.5kPa (10 kg) was applied on top of the model raft for each case. The results of the model tests have been simulated by a general purpose 3-D finite element software and the model has been validated with experimental results. The moments of the pile obtained from the model tests and those predicted by the numerical analyses for all the lateral loads matches reasonably well. For matching the trend of bending moments obtained from experiments, validation with theoretical results have been done with the help of Matlock and Reese (1960) approach for a single value of lateral loading. Moreover, a parametric study has been conducted with 5mX5mX0.3m raft size with 0.5m diameter and 5 meter long pile with increasing number of piles namely 2, 5 and 9 respectively to study the response in terms of moment and lateral deformation under available earthquake loadings, like Loma Prieta (1989) and Darfield Christchurch (2010). Bending moments of piles and load deformation curves for lateral loading have been studied for each case in which it is observed that the bending moments of pile significantly reduces (around 4 times) as the number of pile is increased to two, but it decreases to a nearly constant value (it saturates) as the number of pile is increased to five and nine. Moreover, the lateral deformation of piled raft system drastically reduces (around 2.4 times) for two pile system, and it saturates to a constant value with five and nine pile system. All these results indicate the constancy of stiffness irrespective of the number of piles in the piled raft.

Jan 1, 2015

By Marvin L. Whisman

Several parameters controlling the reproducibility of tritium determina¬tion in organic compounds by liquid scintillation counting were evaluated by the Federal Bureau of Mines. These included optimum volume of scintillator solution for maximum counting efficiency, reproducibility of counting a sealed commercial standard and comparison with duplicate counts on laboratory-prepared samples. The error introduced by using microliter pipets, optical differences in counting vials, reproducibility of counting organic samples where quenching is a factor, reproducibility of counting laboratory-prepared samples with an added internal standard, optimum ratio of internal standard activity to sample activity, effect of sample volume upon counting efficiency, count rate at which coincidence losses become apparent, and reproducibility of organic compound radioassay by the standard addition technique are outlined. From the evaluation of these parameters, a technique that can be applied routinely to organic compounds containing tritium has been established, and details are included in this report.

Jan 1, 1961

By William J. Gillich, Gerald L. Moss

PREVIOUS studies of the shock loading of randomly oriented polycrystalline aggregates have firmly established that, after rather short load duration, hydrostatic compression closely approximates the shocked state.' However, McQueen deduced from pressure measurements with good time resolution that, during shock loading, metals begin to undergo a stress relaxation at the yield stress. He suggested that the relaxation is due to plastic deformation accompanying the change from a one-dimensional compression to a three-dimensional, hydrostatic, compression.' Stress relaxation may occur faster as stress is increased above the yield stress, but the existence of unidirectionally compressed states for finite times suggests that the concept of a unidirectionally distorted lattice should furnish considerable insight into the mechanical behavior of materials subjected to shock loading. Here, a crystallographic analysis is presented for the hypothetical situation where atom motion may be considered as unidirectional which, as indicated above, is a useful extension of the macroscopic concept of shock loading to the microscopic domain. Only motion caused by the com-pressive forces is treated; i.e., lattice vibrations upon which this motion is superimposed, as discussed by Fitzgerald, are ignored.3 The purpose of the analysis to be presented is to develop a description for single crystals of the lattice rotations that occur for idealized uniaxial strain deformation. The usefulness of such an analysis in realistic deformation is to give a method of specification of those properties of an initially distorted lattice which would affect the subsequent deformation. Non-axial complications that arise experimentally, such as off-axis rarefaction waves, must be treated in proper context. Consider the material element shown in Fig. 1 and let the compression be uniform at all regions of the element. Then, any interior point of the element is displaced in proportion to its distance from the base of the element. Accordingly, if the top of a unit element is displaced by an amount, (-K), with respect to the base, a point P(X, Y) will be displaced by (-KY). Crystal planes are, therefore, rotated by the compression. Analysis of this rotation may be accomplished from the geometry shown in Fig. 1 where the line OP is the edge of the plane {hkl} and N is its normal. The orientation of the crystal plane with respect to the shock direction is specified by the angle, before deformation. After deformation the edge of plane {hkl}

Jan 1, 1969