Search Documents

By K. Jomoto, H. Majima

"Experimental work has been attempted to find a useful criterion of comminution which can be determined simply in a laboratory. The suitability of the ratio of the square of tensile strength to Young's modulus, St2/E, previously derived from the theory of elasticity as a criterion of comminution, was examined measuring tensile strength, Young's modulus and critical height for drop-weight impact of five different rocks. However, satisfactory correlation between St2 /E and critical height has not been obtained, suggesting the necessity of further experimental verification of the representative value of Young's modulus of rocks. The plot of St2 vs. critical height, however, shows one-to-one correspondence, and this finding suggests that St• may be a useful criterion of impact crushing. Also, a close relationship was observed between st• and the energy index for tumbling mill grinding of •the sample rocks. It is confirmed from these findings that the quantity St• is a useful criterion of comminution of rocks, not only for impact crushing but also for tumbling mill grinding. As shown in the experimental part of this paper, the determination ol St with irregularly shaped specimens is simple."

Jan 1, 1972

By Mahdi Soudkhah, Akhter Hossain

Vertical micropiles are generally considered to be low in lateral resistance. Therefore, battered micropiles are often used when additional lateral load carrying capacity is required. However, battering of micropiles can sometimes be restricted due to existing adjacent structures or utilities, especially in highly urbanized areas. For example, presented in this paper are lateral load test data from a 43-story building project in New York City where vertical micropiles were used due to proximity to adjacent structures. Three static lateral load tests were conducted on micropiles consisting of 13.375-in-outside diameter and 25- to 51-ft-long casings, and socketed 10 to 12.6 ft into the bedrock (gneissic schist). The subsurface profile above the bedrock consists of loose to very dense, mostly sandy and silty soils. The design load for the three test piles was 14,000 lb and the maximum load applied during the tests was 200% of the design load. Lateral load- displacement behavior of the free pile heads from the load tests are compared with the results of p-y analyses based on a widely used p-y method for sandy soils and using a lower and an upper bound estimates of soil index properties and strength parameters. Since the existing p-y curves were formulated for larger diameter driven piles at a specific geographic location, major differences are observed between the results of the load tests and the p-y analyses. In general, the lateral displacements estimated based on the p-y analyses using upper bound soil parameters are relatively closer to the results of the field load testing. Modified p-y curves specific to the sandy and silty soils representative of the general subsurface conditions of New York City matched with the lateral load tests are presented in this paper. INTRODUCTION Micropiles generally are limited in lateral load carrying capacities due to their relatively higher slenderness ratios (ratio of depth to diameter) compared to more conventional deep foundation alternatives, such as driven piles and drilled shafts. So, micropiles are not typically considered as deep foundation solutions when significantly high lateral loads are expected on the substructures. Various means to increase the lateral resistance of micropiles include battering and installing an oversized casing in the top portion of the piles (FHWA 2005; and Richard and Rothbauer 2004). However, it is often not possible to install micropiles in a battered position in highly urbanized areas due to existing adjacent structures or utilities. Installation of oversized casing is often restricted by limited space availability and concerns of losing lateral capacities due to closely spaced group of piles. Thus, estimation of lateral resistance of vertical micropiles can become highly important for geotechnical engineering projects in urban areas when a small to moderate amount of lateral resistances are expected from the substructures, often to withstand seismic and wind loads.

Jan 1, 2019

By R. Blazej

Machinery Systems Division (MSD) in the Institute of Mining Engineering at Wroclaw University of Technology specializes in belt conveying systems analyzing, calculating and design. Within the division operates the certified Laboratory of Belt Transportation (LTT) and Laboratory of Rollers. Since few years, a group of several people have begun work on developing a comprehensive system for the automatic evaluation of condition of conveyor belts working in the mines. Group uses both magnetic devices developed by specialized companies servicing belts and its own machine vision system developed for assessment of belts covers and edges during belt movement (up to 7 m / s) on the specially designed for this purpose the test conveyor. Recently they have got the research grant funded by the National Centre for Research and Development (NCBiR) for development of the system for automatic diagnosing of conveyor belts? condition and aiding of rational belt management. On the basis of previously created diagnostic tool called ABCDE (Automatic Belt Condition Diagnostic Equipment) the five modules: vision-A magnetic-B, preventive-C, forecasting?D, and determining safety factor-E will be developed. They will automatically interpret data about conveyor belts? condition to indicate the extent and timing of repairs, to prevent failures and to select the optimum moments for their replacements. The system will use results of ongoing research & development and planned research concerning modeling of belt wear using evolutionary genetic algorithms. The reached stage of research can not yet allow to start the implementation work by potential users. It is therefore necessary to pursuit research in real scale, the development of new modules (C-E) and intensive testing of the system in working condition with system calibration to optimize the economic effects.

Aug 1, 2013

By M. Younis, E. Comis

"The success of a tunnel project relies on many factors, but one of the most important is also the most overlooked: coordination by all parties involved during the design stages. This is particularly true of segment design and TBM design. Tunnel lining with segmental rings is usually designed according to the standards of reinforced concrete construction based on a given GBR. However, for TBM tunneling, the determination of loads during ring erection, advance of the TBM, earth pressure, and bedding of the articulated ring are all part of the tunnel lining design as well. TBM design can be heavily affected by the segment arrangement, dimension, and weight, but these are usually given as a fixed input to the TBM manufacturer—a process that can cause unnecessary complications. The authors propose that the industry evaluate the process as it stands. In order to find the optimum balance between lining design and TBM cost and operational workflow, both designs should be finalized concurrently. This requires coordination between the TBM manufacturer and segment designer from the early stages. The aim of this paper is to evaluate the influence of the segment lining design on TBM cost and performance, and to provide commentary on existing design guidelines to optimize lining and TBM procurement. INTRODUCTION The conventional project setup for tunnel lining design and the design and manufacture of the tunnel boring machine (TBM) should be coordinated in a timelier manner. It is widely acknowledged that the design of segments must consider the forces exerted by TBM rams during tunnel construction, but other inputs are most frequently provided to the TBM manufacturer as fixed parameters to design around. This paper describes other important factors in TBM design that impact not only the interaction with the segments, but also the construction of the tunnel in terms of overall production and even safety. For example, the segment width and tapering have direct influence on shield body length and thrust cylinder size. Furthermore, TBM geometry can also affect the backup (trailing gear) layout and length."

Jan 1, 2016

By J. S. Becker

Technology developed and first implemented in the United Kingdom enables very low grade aluminum scraps containing oils, organics, plastics and ferrous metals to be directly charged, without pretreatment, into a unique melting furnace. The system has been in full scale production for four years. The oxy-fuel-based furnace design incorporates internal afterburning in the furnace's hot zone, producing excellent thermal efficiency and very low emissions. The furnace is inherently low in NOx. This paper will provide both theoretical background and extensive operating results for this new melting concept. Applications describing both purpose built new furnaces and retrofits of existing reverberatory furnaces will be presented. Extensive operating emissions data will be presented.

Jan 1, 1997

By John A. Emery

The Pea Ridge iron ore deposit near Sullivan, Missouri, is a dike-like mass of magnetite enclosed in Precambrian porphyries. The ore body tops at the Precambrian surface at a depth of 1300 feet below the present surface and extends to an unknown depth. It dips nearly vertically, intersecting the dip and strike of the enclosing porphyries at an extremely sharp angle. Faulting, both pre- and post-ore, appears to be of minor consequence, and present knowledge indicates that no preferred structural conditions existed prior to emplacement. The ore body is composed of magnetite with specular hematite, quartz, apatite, and pyrite occurring as accessory primary minerals. Specular hematite in appreciable quantities occurs on parts of the cap and the footwall of the ore body. Fresh porphyry breccia is enclosed in the magnetite along the hanging wall and in the western portion of the ore body. Hanging-wall quartz-amphibole and footwall quartz-hematite occur as replacements of certain porphyries. Further alteration has caused sericitization of parts of these zones. The ore deposit is interpreted as having been formed essentially by a single injection of a magmatic differentiate with hydrothermal end phases forming the quartz-amphibole and quartz-hematite portions of the deposit.

Jan 1, 1968

By C Swamydas

VV Mineral (VVM) group of companies is the largest and the first private producer and exporter of beach sand mineral products in India. During 2010, the company produced and marketed around 750 000 tons of saleable products. Their operations are mainly in the state of Tamil Nadu and Andhra Pradesh, India. Almost all the wet pre-concentration plants use sea water as the concentration medium, since there is no fresh water source available near the deposits. The mines are located along the south-east coast of India in the states of Tamilnadu and Andhra Pradesh. The orebody varies in terms of mineral assemblage, slime content, grain size, and surface coating resulting in different behaviour of the minerals. Three different deposits containing ilmenite of different TiO2 content were studied. The study shows that there is no significant impact of using sea water for wet concentration prior to high tension separation of ilmenite. There is no significant variation in recovery and purity of ilmenite produced from these deposits when wet concentration of the deposits were carried out with sea water as the concentration medium and whether the concentrates were washed with fresh water or not before dry separation using High Tension Roll Separators (HTRS).

Oct 5, 2011

By M. P. Sinha, Rashmi, Tata Steel Ltd., S. Jaiswal, A. Bhatnagar, P. Garg

Reagents form a crucial part of flotation process as they have the power to control the surface properties of minerals. In case of coal flotation, collectors and frothers are two the important and commonly used reagents. But other types of reagents such as promoters, modifiers and depressants are also finding wide applications because of their availability to improve selectivity and increase recovery. Because of these chemicals the scenario has changed from flotation being used mostly for high rank hydrophobic coals to low rank, oxidised or inferior coals. In the present work a case is presented in which two non-ionic surfactants (abbreviated as A & B) known to act as emulsifier have been studied to get a better flotation performance for a preparation plant with varying feed characteristics. Laboratory flotation tests were conducted with both the surfactants using three feed samples of the plant by varying the dosage at three different levels. The highest combustible matter recovery (more than 80%) was obtained for surfactant B at a dosage of 75 ppm (parts per million) for feed 1. But at the same dosage the recovery decreased by 21% and 10.2 % respectively for feed 2 and 3. On the other hand surfactant A showed a consistent result for all the three feed samples giving the highest value at a dosage of 50 ppm followed by a decrease beyond this point. The tests were complemented by contact angle measurements that demonstrated the same trend. In addition to this the reproducibility of data for Surfactant A was checked and found that the standard deviations for both separation efficiency and combustible matter recovery were within the permissible range (less than 5%). Finally an in-plant process optimization study to evaluate the performance and applicability of surfactant A at industrial level was done and has been discussed.

Jan 1, 2016

By Douglas B. Silver

"Editor’s note: Douglas B. Silver, Portfolio Manager, Orion Resource Partners, was the keynote speaker at the 2017 SME Annual Conference & Expo in Denver, CO on Feb. 19, 2017. He also gave the keynote address to the SME Annual Conference in 2008. The following is his 2017 keynote address with a few of the slides that were presented. The full speech is available on YouTube https://www.youtube. com/watch?v=uF0qwGJIX3UIn 2008, I had the privilege of giving SME’s keynote address. At that time the financial markets were on the verge of collapse and my presentation described the issues. Unfortunately I was correct, and global markets went into a steep nosedive, creating the largest economic downturn since the Great Depression.In hindsight, there were plenty of signs that this was coming. The Supercycle had created massive new wealth. This wealth was largely invested in the United States due to the country’s political stability and credit worthiness. In 2004, the large investment banks convinced the U.S. Securities Exchange Commission (SEC) to allow them to triple their borrowing leverage ratios. This made the banks more vulnerable to market volatility. The banks then lent money to NINJAS - people with no income, no job and no assets. Even worse was the fact that these unqualified home owners used adjusted-rate mortgages (ARMs) which they, of course, intended to refinance prior to interest rates rising. These mortgages were then bundled up by the banks and sold to investors as “safe” investment products. The money flowed into these products because the rating agencies gave these instruments high marks. These same agencies earned their fees from the very same banks seeking high ratings. (No conflict there). Private debt exploded and peaked out in 2008.These mortgage products were sold in an unregulated shadow banking system and the ARMs came due. Toxic mortgage default rates skyrocketed and the mortgage-backed securities collapsed in value. This house of cards had a negative feedback loop that accelerated the market crash and resulted in more than $1.5 trillion being lost in the securitization sector, a 47 percent decline in the Dow Jones Industrial Average, foreclosure rates skyrocketing and housing prices collapsing. The financial markets were in a nosedive."

Jan 8, 2017

By E. Herrera Alarcón, L. Mariscal Samaniego

The Teniente Converter (wet charge type) was commissioned in august 1995 and was designed to smelt 744 tpd (metric tons per day) of dry copper concentrates. Its products are white metal (73% Cu) that is sent to the Peirce Smith converters, slag that is cleaned in Reverberatory Furnaces and the process gases that are sent to the Sulfuric Acid Plant. Since its start up, the Teniente Converter smelting capacity was increased 1.6 times, from 800 tpd to 1,280 tpd using 33% oxygen-enriched air, and reaching an operative availability of 97%. By the other hand its campaigns have reached a record duration of 530 days without hot patching tuyeres and a partial refractory lining repair in the last four campaigns. This paper describes the most relevant improvements, as well as the strategies that had been used to reach these achievements.

Jan 1, 2007

By H. Y. Sohn, Y. Mohassab, D. -Q. Fan, M. Elzohiery, A. Abdelghany

The Flash Ironmaking Technology being developed at the University of Utah is aimed at producing iron directly from iron oxide concentrate. In this technology, the concentrate is reduced by H2 and CO gas mixtures formed from the partial oxidation of natural gas in a flash reactor. Natural gas represents an economically and environmentally superior reductant/fuel for the flash ironmaking. The rate equations for the reduction kinetics by H2, CO and H2 + CO gas mixtures were determined in the temperature range 1150–1600 °C. These rate equations were applied to experimental results from a laboratory flash reactor using Computational Fluid Dynamics CFD simulation. A new mini-pilot reactor, which is capable of operating at 1150–1550 °C with a concentrate feeding rate of 2–5 kg/h, has been installed. Commissioning of the reactor with an emphasis on preheating of the reactor, production of reducing gas mixtures and the feeding and collection of iron ore concentrate and product particles has been completed.

Mar 1, 2017

By I D. Gregson, A S. Garcia, K M. MacAndrew

The design work undertaken by Rock Mechanics Technology (now part of Golder Associates (Golder)) has played a major part in successfully establishing mechanised room and pillar working in Indian coalmines, both for the development of new districts and for the re-establishment of old districts prior to pillar extraction on panel retreat.Golder has used appropriate design of pillars, extraction sequences and final snook sizes to minimise ground control risks during pillar extraction. Where the strata will not cave reliably, partial extraction systems leaving either a crush pillar or a substantial yield pillar have been adopted.Remote monitoring of selected pillars during the extraction process using stress cells, extensometry and convergence measurements provides confirmation of pillar behaviour and verification of designs.A new telltale device, giving a visible warning of impending caving, is now installed at all Indian pillar extraction sites and is proving very successful.CITATION:MacAndrew, K M, Garcia, A S and Gregson, I D, 2014. Coalmine pillar design and performance during mechanised pillar extraction in India, in Proceedings AusRock 2014: Third Australasian Ground Control in Mining Conference , pp 347–358 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Nov 5, 2014

By I Canbulat, A Mcquillan

This paper presents a parametric analysis showing the impact of virgin in situ stresses on a shallow (less than 100 to 150 m) high slope in a jointed sedimentary rock environment. Slope stability is assessed at varying ratios of slope orientation and horizontal stresses. The results of this study indicate stress conditions should be included in stability assessments of excavated slopes, particularly where structure is orientated perpendicular to the direction of horizontal stress. Some consideration of stress state is applied in deep open cut pits (eg those with planned excavations of 400–1200 m) (Myrvang et al, 1993; Stacey et al, 2003; de Bruyn et al, 2014; Kozyrev et al, 2015). Dodd and Anderson (1972), Kalkani and Piteau (1976), Lee (1978), Coulthard et al (1992), Noorani et al (2011) have studied the effect or horizontal stress and its impact on slope stability, showing that tensile stresses tend to develop at the crest of the slope, with larger tensile zones for higher horizonal stresses and steeper slope angles (Stacey, 1970, 1973; Sjoberg, 2013). However, the consideration of virgin stresses on shallow slope stability is less frequent (Lynch et al, 2005; Dight, 2006; Lucas, 2006; Sjoberg, 2013). This has led many geotechnical engineers to believe the impact of virgin in situ stresses on open cut slope stability is minimal and not worth time or consideration in modelling, or their effects on slope stability are still poorly understood (Stacey et al, 2003; Sjoberg, 2013).

Nov 29, 2022

By C. Cristonffanini, S. Nazari

"In the past, simulation was considered to be an offline tool disconnected from plant operation. Advancements in the computation power combined with utilizing physics and chemistry sciences have allowed us to significantly improve the modeling and simulation technology for mining and mineral processing. This paper investigates the benefits of first principle models and simulation by connecting them to real time operation. Process data are connected to high fidelity models executed in parallel to the operation. In recent literature, this concept is known as Digital Twins. The Digital Twin is used for various purposes such as optimization, virtual instrumentation and condition monitoring. Using IDEAS™ simulation software we are able to construct a digital twin for different equipment inside a mineral processing plant. Two case studies for building a digital twin for the primary hydrocyclone feed pump and thickener underflow are presented. Using the pump’s model, a digital twin is developed and is installed in a gold extraction plant that is able to infer the slurry density in real time. Additionally, it is used for detecting sanding in the pipes and impeller condition monitoring.INTRODUCTION Since the eighties, thanks to advances in computation technologies, computer based simulation of processes using first principle models has become a well-known engineering tool for various industries. As our understanding of processes has increased, their representative models have become more realistic and more sophisticated. Due to this increase of accuracy, use of simulation is becoming more fundamental in process industries. The main goals to use accurate simulation is to decrease the engineering and construction cost, optimize the process design and improve the operation performance by decreasing operation cost and increasing efficiency. The term Digital Twin was first introduced in 2010 by NASA (Shafto et al., 2012) in aerospace industry. Subsequently, the concept quickly spread through other industries. As of today, no standard organization has provided an official and unique definition of Digital Twin for process industries. However, there are three important aspects that are common throughout various descriptions. When simulation is core functionality of the process (1) along the entire life cycle of the plant (2) with direct linkage to operation (3), it is called that process has a Digital Twin. According to Gartner, the concept of Digital Twin has elected as fourth most important disruptive technology for the year 2018 (https://www.gartner.com/, 2017)."

Jan 1, 2019

By Donald E. Ranta

An ore zoning technique developed by Climax geologists during the past forty years has been used to contour drill-hole assay values on cross-sections for fourteen porphyry molybdenum deposits in western North America, including the Climax and Henderson orebodies. Detailed geological studies of these large, complex deposits are essential in determining ore controls, which are the factors most critical to the zoning of MoS2 assays and to conceptualizing geologic models. The technique provides a detailed representation of the size, shape, grade distribution, and geologic continuity of the individual deposits. It demands a disciplined approach and adheres to rigorous rules while maintaining flexibility for adaptation to widely varying geologic conditions. By defining the limits that guide and control manual, computer-assisted conventional, and geostatistical reserve estimates, it exerts a strong geologic influence on the estimation process. A combination of ore zoning and geostatistical analysis of molybdenum deposits produces a significantly more accurate, precise, and defendable geologic reserve estimate than other methods.

Jan 1, 1983

By C. B. Yu

The ore comprise of chalcopyrite, valleriite, pyrite, pyrrhotite and so on. Serpentine and talc are chief gangues. Copper phase of the tail shows that mostly valleriite be losed in tail, 70% mineral of copper is valleriite in tail, so severity reduce the recovery of copper. The traditional flow-sheet in acidity mine pulp to flotat the valleriite, but copper-sulphur separated in high alkaline pulp, so the valleriite be losed else. Explores the characters of the valleriite?s surface, studys on the flow-sheet of flotat valleriite and copper-sulphur separated. In neutral mine pulp, adopt of cationic collector to flotat valleriite, adopt of hyposulphite to depressant pyrite in low alkaline pulp can advance the recovery of copper to 5.06%.

Jan 1, 2014

By W. C. Whittaker

COMPLETED in November, 1943, at a cost of over $1,500,000, Elk River colliery of the Crow's Nest Pass Coal Company, Limited, has been laid out and equipped for an ultimate annual production of 1,000,000 tons and replaces the recently closed Coal Creek plant, which has been operated by the Company for the past forty-five years. The project has involved the opening of mines in three seams, the construction of a complete set of colliery buildings, including a modern preparation plant of 360 tons per hour capacity, and the laying out of the necessary yard tracks and spur connecting the new development with the Company-owned Morrissey, Fernie and Michel railway, which, in turn, connects with the Canadian Pacific railway at Fernie. The colliery is three and a half miles east of Fernie, B.C., near the southern end of the Crow's Nest coal field, which contains the largest and most important body of coal in the Province of British Columbia. The coal-bearing horizon is the Kootenay formation, present in the form of a syncline covering an area of 230 square miles. Most of the coal seams occur in the lower 2,000 feet of the formation, the covering beds being largely coarse sandstones and conglomerates of great thickness, the presence of which accounts largely for the preservation of the coal measures. James McEvoy, in the report of the Geological Survey of Canada for the year 1900, states that the basin appears to contain a fairly constant coal content of nearly 172 feet in 23 seams of a thickness of one foot or over. Coal has been mined in the Fernie district since 1897 and the first shipments were made from Coal Creek colliery in the following year, over the then newly constructed British Columbia Southern railway. Since that time, a total of over 16,000,000 tons of coal has been produced, an average of 350,000 tons per year. The7ears of peak production were 1910, 1912, and 1913, with an all-time high of 924,000 tons in 1913. The lowest output in the history of Coal Creek was that for the year 1933, when only 60,340 tons were produced, the colliery being closed for some months. Present production from Elk River colliery averages 1,150 tons per day, the output being considerably less than it could be were sufficient man-power available.

Jan 1, 1944

By Marc. A. Meyers

The analysis of the phenomena involved in the determination of the compressive strength of iron-ore agglomerates leads to the identification of the important parameters. It is shown mathematically that the pellet rupture strength is proportional to the cross-sectional area. Fracture is initiated at the center of the pellets by the tensile stresses developed by the compressive loads normally to the compression axis. The variation in strength between individual pellets of identical composition and subjected to identical treatments is due to internal voids of varying sizes, that act as stress-concentration sites. Two novel testing procedures are proposed. The first consists of testing the pellets between two plates having three steel spheres each. This configuration simulates much better the environment actually encountered by the pellets. The second procedure consists of a thick-walled cylinder in which a piston penetrates; a large group of pellets is tested simultaneously, as the stress versus strain plot is being recorded. This latter test presents significant advantages over the conventional testing procedure; the main one is that one single test is sufficient to characterize the mechanical response of the pellets.

Jan 1, 1981

By V. Runkana, N. K. V. Nadimpalli, S. Sahu

"IsaMill™ has been in operation in the recent past for fine grinding of low grade ores to extract non-ferrous minerals. IsaMill™, typically, consists of a series of uniformly spaced identical disks mounted on a rotating shaft which is encased in an outer shell. The mill offers high energy efficiency for fine grinding and an inherent scalability. But, it encounters certain operational challenges such as non-uniform distribution of grinding media coupled with high wear rate of the disks and solid walls of the mill at specific locations—which adversely affect the mill performance. To circumvent these operational challenges, design modification of the disks through heuristics, by introducing a reduced diameter disk (RDD) at specific locations, is a common practice in industry. But there is no systematic scientific study in this regard. In the current work, we developed a discrete element method (DEM) based model and simulated for the IsaMill™ operation to study the effect of RDD on the efficiency of the mill and wear rate of the solid walls and disks. Since the first set of disks experience the high wear rate due to the high loading of the charge, the RDD was introduced at the first two disks. The simulations were performed at different diameters of the RDDs and at different media loadings. The performance of the mill was analyzed based on the power consumption, the wear rate on disks and the distribution of media particles inside the mill. Besides, the performance variables such as mean velocity of media particles and total impact energy provided useful insights into the milling operation. It was observed that the reduction in disk diameter yields lower wear rate of the disks at the cost of decrease in power draw at a constant high media loading. Whereas, when the media loading was decreased, the amount of wear and power drawn was comparable for both the most reduced and least reduced disk diameters. Therefore, there is an optimum choice of RDD for a given mill loading to maximize the mill performance while reducing the wear rate of the disks."

Jan 1, 2018

By Ali Azizian, Brian Hall

"Driven piles were selected to support the Fraser Heights Bridge bents. Piles were a key component of the top-down construction approach, which was adopted for minimizing potential impacts on an environmentally sensitive wetland. Project requirements mandated verification of pile capacities using dynamic methods. More than 40 Pile Driving Analyzer (PDA) tests were performed. The subsurface conditions were highly variable. On the east side, piles extended through loose sands, soft silts/clays, and two peat layers and were founded in glacial till-like soils at about 45 m depth. However, on the west side, till-like materials were so shallow that it was difficult to drive the piles sufficiently deep to obtain the necessary lateral support. This paper provides an overview of the geotechnical considerations of the bridge design and top-down construction approach, and expands on the presentation of PDA results and how they compared to pile capacity estimation methods and parameters recommended in the applicable design codes.INTRODUCTIONThe Fraser Heights Bridge (FHB) was a component of the Fraser Heights Connector (FHC), a 2 km section of the South Fraser Perimeter Road (SFPR), constructed as part of the Port Mann/Highway 1 (PMH1) Improvement Project. The FHC is located in northeast Surrey BC (Fig. 1).Two major design and construction determinants were: 1) a mandated tight schedule to provide a non-tolled alternative to a new toll bridge; and, 2) an obligation that construction had to occur with minimal impact on the environmentally sensitive wetland the FHB crossed, including limiting the footprint of the permanent and temporary works to less than 45 m2, and prohibiting construction access onto the wetland. Construction equipment was only allowed on the wetland on temporary trestles or on the finished structure. This latter requirement resulted in the bridge being constructed span by span, using a top-down approach."

Jan 1, 2016