Search Documents

Gold recovered on the strikes at the Central Norseman mill, Norseman, Western Australia, has an approximate assay fineness of 850. Bullion recovered from the cyanide plant at the mine is of much lower value, and occasionally its assay fineness has been as low as 250. This indicates either that the fine gold particles in the ore consist of an alloy richer in silver than the coarse particles or else that a silver mineral, as well as the gold, is dissolved by the cyanide solutions.It had been observed at the mine that the amount of silver in the bullion appeared to increase when galena appeared to be more abundant in the stoped ore. Interest was, therefore, attached to the possible occurrence of a silver mineral associated with galena and, at the same time, soluble in cyanide.Four specimens of ore from different horizons in the mine were collected by the mine staff for examination as to whether any marked difference in the fineness of gold was apparent on a polished surface and for determination of the silver minerals. As the Norseman ore-body is a quartz reef containing a very small percentage of sulphide, the specimens were selected either because they cont;:lined free gold or because they were, relatively rich in sulphides. They were obtained from the following localities at the Phoenix shaft.1. Level 16, section 28.2. Level 16, section 31.3. Level 8, section 31.4. Level 14, section 38.Specimens Nos. 1 and 2 were thus obtained from different positions at the same mining horizon, while specimens Nos 2 and 3 were obtained from different levels in the same vertical section of the mine.All the specimens consist of quartz characterized by thin, discontinuous seams of sericite and the presence of a little ankerite. Gold and sulphides tend to be localized along these seams, but particles of gold and sulphides are also scattered throughout areas of white quartz. This scattered distribution of the sulphides in relatively wide areas of quartz has involved the preparation of two or more polished sections from each specimen.The outcome of the microscopical examination of these specimens has been to determine that there is no appreciable variation in the colour of the polished particles of gold and, therefore, no marked difference in the amount of silver alloyed with the coarse and fine particles. The presence of small quantities of the tellurides sylvanite, hessite and altaite has been revealed, and found to vary in abundance with the abundance of galena.

Jan 1, 1944

By Roger Payne, John R. Goode, Feng Gao, James Brown

The Eco Ridge deposit is located in the Elliot Lake mining camp in Northern Ontario, Canada. Between 1955 and 1996, the area produced more than 138,000 t (300 million pounds) of U3O8 and very significant amounts of thorium and heavy rare earths. Based on the NI 43-101 Preliminary Economic Assessment by Roscoe Postle Associates (RPA) dated June 2012, and the economic review by RPA as announced in Pele Mountains’ Press release dated September 12, 2013, the Eco Ridge Mine Project would extract and process 46 Mt of material to produce about 19,000 t (42 million pounds) of U3O8 and about 65,000 t of rare earth oxide (REO) over a 14-year life. This paper discusses process optimization studies including beneficiation and hydrometallurgical testwork. The proposed modified flowsheet includes the flotation and processing of 1) a pyrite concentrate, 2) a dominantly light rare earth elements (LREE) concentrate, 3) a concentrate containing most of the balance of the uranium and heavy rare earths (HREE), and 4) a relatively inert tailings.

Jan 1, 2014

By Eduardo Gomes Vieira

O Projeto 4ª Pelotização surgiu com o propósito de aumentar a capacidade de produção de pelotas da Samarco em 37%, por meio da implantação do 3º Mineroduto, com capacidade de 20 Mt/ano, a 4ª Usina de Pelotização com capacidade de 8,25 Mt/ano e o 3º Concentrador com capacidade de 9,5Mt/ano. O projeto proposto visa estruturar o processo de Manutenção do Concentrador 3 através do sistema de gestão de dados utilizado pela Samarco Mineração, o software SAP, com foco na criação de um modelo taxonômico de níveis hierárquicos contendo informações técnicas dos novos equipamentos e respectivos sobressalentes, dando base para definição de uma política de estoque, a implementação de planos de manutenção e estudos de confiabilidade. Objetiva a redução do Risco Operacional, consolidando no sistema os processos que compõem a função manutenção, referente à terceira Usina de Beneficiamento de Minério de Ferro da Samarco Mineração. Para isto, foi utilizada a metodologia Kaizen para estruturação e desenvolvimento do trabalho e estabelecimento de metas para controle das informações. Verificou-se uma grande demanda de avaliação de criticidade e cadastro dos equipamentos e sobressalentes, além disto, a falta de organização das informações de forma estruturada poderia acarretar dificuldades de se analisar itens faltantes. Foi necessário também o estabelecimento de critérios para implementação de planos de manutenção visando à preservação da integridade e funcionalidade dos equipamentos.

Aug 16, 2017

By F. Ziaie

Line electrical resistivity method using physically infinite distance between current line electrodes is proposed to determine the location of mine workings. In this method at least three line electrodes are used. One of the current electrodes is used as a sinkhole electrode while the other two are used for different activiations of line electrodes when the survey area is between one of the line electrodes and outside the other one. The resistivity profiles perpendicular to the current line electrodes for different activation of electrodes is plotted versus the distance of the midpoint of the measuring potential electrodes. The anomaly due to presence of any locally lateral resistivity variation (e.g. mining cavity) will represent itself as peak or trough depending on resistivity contrast between the source of the anomaly and surrounding medium. Physical simulation of the proposed model was conducted by using a tank model in the laboratory. The results of experiments appear to be consistent with the theoretical model. Experiments for different depths and different spacial locations of the simulated cavities appeared to be successful for locating the depth and size of the cavity.

Jan 1, 1989

By L. M. Lowe, D. G. Feasby, J. R. Goode

"Rare earth resources usually contain minor amounts of radioactive elements. The most widely recognised sources of radioactivity are associated with thorium and uranium. However, also present in the resources are isotopes of rare earth elements (REE) that are themselves radioactive, including lanthanum (La-138), lutetium (Lu-176) and samarium (Sm-147). These radioisotopes, as well as remnants of the natural thorium (Th-232) and uranium (U-238, U-235) decay series, can contribute to significant levels of radioactivity in mixed REE concentrates and in separated products. Levels such as these can present challenges for transport, transboundary movement, product storage, workers’ health and safety, as well as waste management issues at the facilities that separate out the individual REE’s. These are discussed in this paper. A particularly challenging radioactive isotope is Ac-227 (a decay product in the U-235 decay series). Actinium behaves chemically similar to lanthanides and hence normally concentrates with REE multi-element composites. Reliable analysis of Ac-227 is not widely available and the methodology required to deal with this challenge is briefly described. A principle reason for minimization of radioactive content throughout REE processing is restrictive specifications by concentrate purchasers in order to reduce waste management challenges. Approaches to the minimization of radioisotope content in REE concentrates and separated products are outlined in this paper."

Jan 1, 2014

By J. E. Nesset, F. Rosenblum, J. A. Finch

"The self-heating of sulphides can be a major hazard in mining operations and concentrate handling, particularly during transportation and associated storage. Self-heating results from the oxidation of sulphide minerals and can vary from being insignificant to highly reactive and potentially hazardous to both humans and infrastructure. It is essential that there be a reliable test methodology that can measure and categorize a given sulphide material as to its self-heating potential. By their nature, sulphide ores and concentrates are complex and variable mineral mixtures making it difficult to predict their self-heating behaviour a-priori based on mineralogy or with a simple “snapshot” test. Furthermore, self-heating behaviour will depend on the state of oxidation of the sulphides as well as time, temperature and humidity. A review of available testing apparatuses and protocols that can be used to assess self-heating potential is presented. Each of these methodologies was examined in relation to its ability to measure and reliably predict the latent self-heating hazard of a sulphide material. Several of the methods were tested and compared to illustrate their strengths and weakness. The results indicated that a number of the test protocols may produce false negative indications of self-heating potential, constituting an obvious concern to the industry.INTRODUCTION Sulphides as well as other materials (coal, wood chips, hay, powdered milk, to name a few) that are stockpiled in an air atmosphere may undergo oxidation reactions which can result in the evolution of heat (Beever, 1984) (Hudak, 2002) (Blanchard, 2007). If the rate of heat generated exceeds the rate of heat dissipation, the stockpile temperature will rise, potentially leading to “hot spots” in the most reactive areas, and possibly even fires. The heat generation rate, the “self-heating” rate, depends on many factors such as the type and composition of material, particle size, moisture content, oxygen availability, ambient temperature and humidity, and of prime importance, the extend of prior oxidation, or more specifically, the presence of oxidation products. The desire of operators that mine, process or transport sulphide-bearing materials with a potential for self-heating is to have an accepted and reliable method for evaluating and quantifying the potential hazard of their material. The challenges are how to best measure the self-heating properties of given samples, and based on results, predict the behaviour of the bulk material over time and in-situ. Generally, when evaluating a given material one derives the self-heating characteristics of that sample at the time and under the conditions of testing, which will be referred to as a “snapshot test”. If that material is invariable, i.e. it will not change its response over time, then it may be considered to be a “predictive test”. However, if as a result of continuing oxidation or other changes, the material becomes more or less reactive with time, then a “snapshot test” is unreliable with respect to predictive ability."

Jan 1, 2014

By Sergei Decterov, Peter Hayes, Evgueni Jak, Taufiq Hidayat, Denis Shishin

Copper smelter operations around the world are under sustained pressure to reduce costs and increase output. Through the provision of reliable data on fundamental properties of the chemical systems the opportunities for improvements of industrial copper production can be identified. Experimental and modelling studies on phase equilibria, thermodynamics of copper slag/matte/metal/gas systems have been combined into an integrated research program undertaken at PYROSEARCH. Experimental phase equilibria studies involve high temperature equilibration in controlled gas atmospheres, rapid quenching and direct measurement of compositions of equilibrium phases with electron probe X-ray microanalysis (EPMA). Thermodynamic databases development and modelling is undertaken using the computer package FactSage in conjunction with advanced models used for complex solution phases. Progressive development of these research methodologies has brought significant advances in characterisation of these complex systems, including a new optimised thermodynamic database for the copper-containing slag system Cu2O-Al2O3-CaO-FeO-Fe2O3-MgO-S-SiO2.The new data and models can now be applied to assist in improvements of the processes. The effects of changes to chemistry and process conditions within the smelting reactor can be examined. Several examples of new descriptions of the phase chemistry of the Cu2O-CaO-SiO2 and Cu2O-FeO-Fe2O3-SiO2 systems in equilibrium with metallic copper showing calculated and experimental data are presented.

Jan 1, 2014

By J. Bruce Clemmer

In the experimental concentration of Vermont talc-magnesite ores, talc concentrates and tailings rich in magnesite were obtained. On account of the possible market value of the magnesite, the tailings are given consideration' in this report along with the talc. After some comments about the talc industry, the magnesite that accrued as tailings will be considered. Then the flotation results will follow.

Jan 1, 1936

By Robert A. Jankowski, J. Drew Potts

In this U.S. Bureau of Mines study, four underground respirable dust surveys were conducted to determine factors affecting belt entry dust levels and how using belt air to ventilate work areas affected dust exposures. Belt entry dust levels on the surveyed longwall and continuous miner sections averaged 0.59 and 0.26 mg/m3, respectively. The stageloader-crusher contributed an additional 0.5 to 0.9 mg/m3 of dust to belt air, while the feeder-breaker contributed 0 to 0.2 mg/m3 of dust. A 1,000-ft increase in belt entry length or a 200- to 500-st-per-shift increase in production resulted in roughly a 0.1-mg/m3 increase in dust. Using the belt entry as an intake entry on the continuous miner section appeared to reduce dust levels by 0.1 to 0.3 mg/m3 during cutting. Belt air was not used to ventilate the face on the longwall section.

Jan 1, 1992

TIMBER supports for large underground cavities are temporary expedients until the permanent filling can be put in. Nevertheless, timber supports are very necessary in some form. The general problem is to support the cavity in all directions withthe minimum of timber, disposed in the strongest way. The simplest way of filling an irregular space with timber sets is to form triangles.The right-angled isosceles triangle (Fig. 1) leads to the true square set, in which caps are equal to struts. The right-angled unequal-sided triangle and the scalene isosceles triangle (Fig. 2) lead to the oblong square set, where caps are longer than struts.The scalene triangle (Fig. 4) leads to the rhombic or oblique set. The equilateral triangle leads to the hexagon set (Fig. 3), in which the caps and struts are all equal. These five plane figures, the triangle, square, rectangle, rhomb and hexagon, are the only figures that will completely fill any irregular plane figure, without interstices. Hexagon sets were first suggested by the writer in 1902 to a mine manager at Broken Hill, who did not see his way to use them.

Jan 1, 1912

By Harlan L. Kebel

Gypsum, the dihydrate form of calcium sulfate, has a history of usefulness to man dating back several thousand years, and a worldwide industry has been built on the mining and processing of this versatile industrial mineral. However, anhydrite, the other prin¬cipal calcium sulfate mineral, has very limited use, so much so that separate statistics for it are not always kept, but are usually included with those for gypsum. Although often found in close association, the two minerals have important chemical differences in that anhydrite is the anhy¬drous form of calcium sulfate (CaSO4) whereas gypsum is the dihydrate (CaSo4.2H20). These two molecules of combined water result in significant differences in hardness, density, and solubility of the two minerals. Of most importance, however, is the difference in thermal properties wherein gypsum, upon the application of a modest amount of heat, can be converted to the hemihydrate of calcium sulfate (CaSO4 '21H20) or plaster of paris, an intermediate product upon which is based over 90% of the value of all calcium sulfate end products. Anhydrite, on the other hand, is inert at these temperatures and its uses have been limited to only those few cases where calcium sulfate in the anhydrous form may have an advan¬tage. The earliest known use of gypsum plaster dates back some 5000 years to the time of the Pharaohs of Egypt who had discovered that gypsum rock, when exposed to fire, broke down into a powder which, when mixed with water, would form a putty that could be plastered on a rough mud brick or stone wall to make a smooth finish. It was used down through the centuries in a limited way for ornamental purposes, but did not achieve wide acceptance because of the quick (25 to 30 min) setting or hardening time which made it difficult to use. The first real understanding of gypsum chemistry was developed in France about 1755, and the gradual growth of its present utilization dates from that time. In the United States, the first utilization of gypsum was to grind it to a fine material for use as a soil conditioner at about the time of the Revolutionary War, and the term land plaster for ground gypsum was coined and has remained in use. Another cementitious material-lime or calcium oxide-had become the usual plastering material, but by about 1870 a method for retarding the set of gypsum plaster was discovered; today it has almost completely replaced lime as a plastering material. In recent years, gypsum products sold in the United States have reached a total valuation of approximately $2 Gpy as illustrated in [Table 1].

Jan 1, 1994

By R. Biss

"Niobium or columbium, as usually called in North America is becoming a more and more important metal in the industrial world because of its attractive properties.Eventhough discovered in the early nineteenth century, it was not until the 1930's that its use became more widespread. The discovery of large commercial deposits in the late 1950's and the demand of industry for steel with high strength and toughness further promoted its use. To assure its adequate supply new or-e processinr technologies had to be developed. So, beside the traditional gravity concentration, the flotation process was employed for the partial upgrading of pyrochlore concentrate at S8ve (Norway) plant in 1953. The flotation process was equally used at St-Lawrence Columbium plant in the province of Quebec, Canada. The new plants at Araxa and Catalao in Brazil and at St-Honore, Canada, which supply almost of all niobium used today in the non-Communist world, also adopted the flotation process. The processes using long chain aliphatic rnonoarnines, diamines or sulfonates as collectors proved to be difficult especially on weathered types of ores or on those having a substantial content of silicate gangue minerals. They almost completely failed in case of alkaline intrusive rocks as syenites, nepheline syenite, ijolites and pyroxenites, composed almost entirely of silicate minerals. A lot of effort was devoted all around the world on research of new, more efficient flotation processes. So in 1982, Les Services T.M.G. Inc. (Niobec), sole producer of pyrochlore concentrate in North America, developed the direct pyrochlore flotation process from carbonatites. In 1983, at about the same time, the Quebec Department of Natural Resources Laboratories and Les Services T.M.G. Inc. announced a successful recovery of niobium Minera1s from a low grade nenheline syenite ore."

Jan 1, 1984

By C Johnstone

Project management is not a task to be undertaken lightly. Mining projects generally present even more challenges due to ChinaÆs remoteness and complexity. Having experiences in project management in the West is certainly an asset, but China can present the uninitiated with any number of headaches. To undertake a project there can have many problems that are unique to China. For the last 15 years, China has seen an increasing number of foreign capital investment projects in the mining industry. Practices involved in mining project development have experienced/are experiencing an evolution. Since 1996, Sino Gold Mining Ltd has delivered three mines in China, ie Jianchaling Gold Mine, Jinfeng Gold Mine and White Mountain Gold Mine. Through the work, Sino Gold has established a solid knowledge base and a capable and skilful workforce in effectively undertaking mining projects in China. This paper is concerned with the experiences accumulated so far by Sino Gold in project management in China. An overall review is conducted regarding the reform of the mining project development in China. Opportunities and challenges are highlighted within the political, economic and culture context. Brief summaries of the development of the three gold mines are presented.

Jan 1, 2009

Up to the end of World War n, flat-back cut and fill stoping with or without square sets was the universal method of ore extraction. Rapid changes in practice occurred during the post-war years; first, ore extraction was fully mechanized; secondly, the stope design for new levels, notably No. 17 Level Zinc Corporation Ltd. and No. 19 Level New Broken Hill Consolidated Ltd., was modified to suit this mechanization; and thirdly, sub-level and shrinkage stopes were developed in orebodies where cut and fill methods would be uneconomical. The following is a brief survey of the changes that have occurred-most of which were inaugurated during the last five years.ROCK DRILLINGDuring 1951 open stoping was investigated in detail. In order to reduce steel handling problems, forged steel onepass detachable bits were introduced, but were soon superseded by the "Swedish method". Investigation showed that when using a bar and arm mounted 3-in. drifter the overall drilling time was approximately 6 min. per ft. compared with 4 min. per ft. using the light jackhammer-airleg combination with 1-in. hex. by 4-in. collared shank tungsten carbide-tipped steel.Although competitive with tipped steels on a cost per foot drilled basis (excluding miner's time), detachable steel bits proved most unsatisfactory for hard drilling conditions.Rapid blunting necessitated frequent bit changes and thus caused lost drilling time. This, together with rapid gauge...

Jan 1, 1957

By Douglas Rudenko

Have you ever had a neighbor complain about a blast one day, but says the next day’s blast was better, even though the Peak Particle Velocity (PPV) increased? How about neighbors that complain about a small trimming shot, but don’t complain about a big production shot? Have you ever reduced the pounds/delay and gotten more complaints ? Mine operators are often bewildered when trying to correlate blast design parameters to homeowner complaints. When complaints come, standard practice is to set up a seismograph in the neighbor’s yard to monitor the blast. Immediately after the blast, the neighbor usually reappears from the house wanting to know the seismograph reading. When told that the PPV was 0.1 in/set, well below damage levels, the homeowner explodes saying “Your machine is wrong”. Perhaps he is right. Understanding why people complain about blasting is not about PPV, it’s all about structural response. People could care less about how much the ground vibrates; they only care about how much their house vibrates. In this paper we will examine the primary factors that control structural response. Through the use of a large array of digital seismographs, the effects of two production blasts on a community surrounding a quarry are studied. The predicted structural response resulting from each blast is calculated at 175 seismograph locations. The predicted response is then correlated to previous research on human perceptibility to vibrations. The results of this analysis and correlation give a better understanding of what the residents actually feel in their homes. The detonations of two single-hole signature blasts are also recorded by the array of seismographs revealing the dynamic characteristics of the geology ‘surrounding the quarry. Once the influence of the geology was understood, blasts were configured to disrupt the natural rhythm of the site through the use of millisecond delays.

Jan 1, 2000

?Why TSM in Canada ?How it was developed ?Architecture and Goverance ?COI panel ?Performance indicators and how they work ?External Verification ?Reporting ?The national organization of the Canadian mining industry ?Mining, smelting and refining of base and precious metals ?Mining of iron ore, diamonds, uranium, oil sands, coal and industrial minerals ?Many associate members ?www.mining.ca

May 1, 2011

By Louise Pearce

?Environmental and social impact assessments (ESIAs) are: ??process-driven and scientific processes ??The process entails a number of steps and procedures which result in obtaining a licenceto operate ?and moving more towards a social license to cooperate. ?However, the primary premise of ESIA is to facilitate the consideration of environment and the communities in planning and decision-making which would ultimately make it possible to arrive at decisions that are ?sustainable?. ?Hence, ensuring the development of the mining sector on a sustainable basis is a critical challenge that needs to be addressed by the global community.

May 1, 2011

By J. B. Brodie, C. Pelletier

"The vulnerability of Canadian and U.S. companies, their directors, officers and employees to onerous penalties associated with violations of environmental statutes and common law actions has provided the impetus for the increasing use of environmental audits. This trend is developing in direct proponion to the cost and difficulty of obtaining liability insurance. Companies operating in British Columbia should be cognizant of developing legislative and enforcement trends and their implications for individual and corporate responsibility. Canadian mining companies doing business in the U.S. should be particularly aware of the environmental exposure which may be assumed with property acquisition or by operations which produce or use any of an ever-increasing list of regulated substances.The environmental audit is now a key component of prudent business planning which will identify noncompliances and environmental liabilities, outline defensive strategies, and assist in a legal defence should charges be laid. This paper will discuss the purpose and mechanics of an environmental audit with emphasis on those features which will maximize protection against statutory and common law actions.IntroductionThe environmental audit is but one weapon in a comprehensive defensive strategy for corporate and individual survival in an increasingly litigious world. The principles of the environmental audit have been formulated as a logical response by management to an ever-growing list of environmental vulnerabilities, which often have the potential to result in plant shutdowns, prosecutions or fmancial liability of major proportions. Accordingly, the audit may play a critical role in maintaining profitability as well as assisting in the defence of a company and its employees against actions taken by regulatory agencies and citi7.cns under statute and common law. Should convictions result from these actions, the penalties are likely to be ameliorated by the demonstration of due diligence through management policy supporting the audit procedure.An awareness of environmental sensitivities, strict adherence to licensing requirements, and planning for environmental emergencies are now generally considered to be as important to profitable performance as operating costs, metal prices, and labour peace. Why is this so? The increased priority given to environmental matters is partly a result of changing attitudes amongst the mining profession, but perhaps more importantly, it is also a direct consequence of the proliferation of ever more stringent environmental legislation, the targeting of management for responsibility and the draconian penalties imposed for violations of such legislation. Contributing to this trend are recent court decisions involving disputes of an environmental nature in which the standard of care required for a successful defence now requires almost super-human diligence in environmental management. The principle of ""strict liability"" (in which negligence or permit violation does not have to be shown) is also being increasingly applied in the resolution of civil actions."

Jan 1, 1988

By R. Dippenaar

The emergence of new steel grades is largely driven by the need to produce high quality steel at a competitive price. The principal aims are to attain ultra-high purity, (especially low interstitial elements) and ultra-cleanliness (by the control of the inclusion content and size). Whereas the steel used to build the Titanic contained 650 ppm sulphur, resulting in MnS stringer-inclusions 25 mm in length, modern quality requirements for arctic pipelines would only allow 10 ppm of sulphur and inclusions in ball-bearing steels must be smaller than 5µm. Most developments are aimed at hot-metal treatment before refining and ladle treatment after decarburisation. Because ferroalloys are added during or after the refining step, it is the secondary (ladle) refining production technologies that are of specific interest to the ferroalloy producer. Through ladle treatment, hydrogen and nitrogen contents are reduced, ultra-low levels of solute impurities are attained and the shapes as well as the composition of inclusions are modified. Steelmakers are concerned about the cost effectiveness of the use of ferroalloys such as consistent product analysis and delivery, improved financing arrangements and technical support. Minimal variation in product sizing is vital because it impacts on handling problems and because particle size determines the rate of particle dissolution. The required ferroalloy product quality depends on the specific use but in general sulphur, phosphorous and nitrogen contents are of concern. Apart from the presence of trace and impurity elements, ferroalloys also contain inclusions. For example, ferromanganese may contain MnO-MnS-SiO2 inclusions while high-carbon ferro-chrome may contain different kinds of Cr-Mn-spinels. The presence of these impurities and inclusions has a significant impact on steel production techniques and cost and hence, on the selection and use of ferroalloys. The interrelationship between ferroalloy quality and steel production technology is plant and product specific and hence, effective communication between ferroalloy suppliers and steel producers is essential.

Jan 1, 2004

Interest in industrial minerals in recent years has increased to such an extent that it has taken them into the mainstream of the Australian mineral industry. Notwithstanding that time series data on the values of production, exports, and imports show that industrial minerals are overshadowed by metals and energy minerals, their contribution to the national economy is important and more significant than would seem to be indicated by the statistics. Whereas the ex mine value of metals generally includes some processing (at least to a concentrate stage), most industrial minerals are valued at little more than their extraction cost, in addition to which such costs are generally low because most industrial minerals are exploited in low-cost surface operations. Consequently, values of mine production of metals and industrial minerals are not strictly comparable in that values of mine production of metals tend to be overstated Short term growth of the industrial minerals sector is assured because of several new projects already commissioned but not yet reflected in the statistics. Longer term growth is also assured, based on various other major projects that are likely to come on stream in the early to mid 1990s.

Jan 1, 1989