Search Documents

By Michael E. Karmis

New and developing communication systems en-able underground miners to, not only connect to the surface from an increased communication coverage area, but also to be discovered in the event of an emergency. Communication and tracking systems are required by the U.S. Mine Safety and Health Ad-ministration (MSHA) regulations, aiming to enhance health and safety and routine production in underground operations. Modeling a mine?s potential communication coverage area will increase overall coverage and efficiency of the communication network itself. Modeling the propagation of wireless communications enables ideal broadcast locations to be found when designing a communications network. Strategic placement of broad-cast devices results in a reliable communication network that can better withstand disruption in daily operation and during a time of emergencies. Research on wireless communication in mines has been ongoing since 1922, when the U.S. Bureau of Mines performed experiments in its experimental mine in Bruceton, PA (Schiffbauer & Brune, 2006a). Ac cording to Dobroski and Stolarczyk (1982), ?as early as 1922, Bureau of Mines experiments showed that radio propagation in mines was possible but not practical.? In 2006, the underground communication technologies available to the mining industry had inherent problems that limited communication capabilities. Because harsh underground mine environments significantly reduce line of sight and propagation range and introduce power and safety concerns, the overall effectiveness of underground communication technologies were limited. After several coal mining accidents in early 2006, the U.S. Congress responded with the Mine Improvement and New Emergency Response (MINER) Act, enacted

Jun 1, 2010

By F. A. Forward, A. H. Ross, J. Halpern

Application of the carbonate leaching process to carno-tite ores has often been limited by the difficulty of obtaining simultaneous high recoveries of uranium and vanadium. The chemical aspects of this problem are discussed and the effect of prior roasting procedures on this discovery is described. IN treating carnotite ores by carbonate leaching it is often necessary to subject the ore to a prior roast. Among the advantages that may result from roasting are: 1) improvement in settling and filtering characteristics of the ore; 2) destruction of carbonaceous impurities that would otherwise contaminate the leach solution and consume carbonate reagent; and 3) substantial increase in extraction of vanadium, which is usually low when the un-roasted ore is leached. Recovery of vanadium may be an important factor in processing carnotite ores, and the fact that vanadium is usually recovered in good yield by acid leaching has often been an economic advantage over results obtained with carbonate leaching. It has been found that response of an ore to carbonate leaching, following roasting, depends primarily on its composition and on the conditions of the prior roast treatment, particularly with regard to the roasting temperature, the atmosphere maintained above the charge during roasting and cooling, and the presence of certain reagents. These factors, especially the last, virtually determine the extractions of uranium and vanadium attainable by carbonate leaching, as well as the reagent consumption on leaching, whereas adjustment of the leaching conditions has only a limited influence. These variables were examined systematically to elucidate roasting and carbonate leaching of carnotite ores and to establish a treatment yielding high recoveries of both uranium and vanadium. Tests were conducted on samples of four different Colorado Plateau ores, described in Table I. Roasting Procedure: The roasting tests were conducted in an electrically heated furnace in which the temperature was controlled to ±15°C. The ore (usually a 500-g charge) was ground to —100 mesh, mixed with the desired reagent, and spread in a silica tray to a bed depth of about 1/2 in. During the roast the charge was rabbled at intervals of 15 min. To provide free access of air the furnace was usually ventilated; however, in a few experiments a controlled atmosphere such as carbon dioxide or hydrogen was maintained above the charge. Leaching Procedure: The pulp, generally comprising 500 g of ore and a 2000-cc solution containing 80 g per liter of Na2CO8 and 20 g per liter of NaHCO3, was agitated in an autoclave at 120°C, under 30 psi 02. Samples were withdrawn periodically, and the solution and ore residue were analyzed. Under the conditions employed, maximum attainable extractions were generally achieved in 4

Jan 1, 1959

By Sun Shao Xian

The Port of Shekou is situated at Shenzhen Bay on the east side of the Pearl River estuary. Geological condition of the site is quite complicated. On top of the sea bed, there is a layer of soft silt 8 - 14 m thick. Under the soft silt, there are intercalated layers of sand, silt and clay. Average surface elevation of the underlying undulatory weathered bed rock is about - 20 m, with a variation of about 10 m. In certain locations, the weathered bed rock is covered with a layer of silt 3 - 4 m thick. This paper gives brief account of three types of wharf structures which are of particular interest, constructed in the last few years: (A) Platform type wharf structure with frontal sheet piling and steel raking pile in the rear; (B) Relieving Platform type structure with steel sheet piling and inclined anchoring HP pile ; (C) Steel pipe pile row supported apron added to a marginal quay. Average construction time of a deepwater berth is about six months.

Jan 1, 1991

Producers with Zero Reportables 2007!: ?New Horizon Mine, Western Fuels Colorado LLC ?Isaacs Run HWM, ICG ADDCAR Systems, LLC ?Savage Mine, Westmoreland Savage Corporation ?South Hallsville No 1 Mine, Sabine Mining Company ?Black Butteand Leucite Hills, Black Butte Coal Company Black Butte and Leucite Hills, Black Butte Coal Company ?Buckskin Mine, Kiewit Mining Group ?Coal Creek Mine, Thunder Basin Coal Company, LLC

Jan 1, 2008

Industrial Minerals production in New Zealand is limited in both quantity and range, but imported in quantities that make New Zealand the world's biggest consumer per head of population. The use of industrial minerals is assured as both population and standard of living increase regularly. But to develop these minerals in the New Zealand environment requires the mineral, or its market (both local and export), to have characteristics that negate the remote geographical location. Volume and/or uniqueness can achieve this.

Jan 1, 1997

By P. Ulrich, V. Svalbonas

The early to mid 1980s was a period of mining consolidation, and many senior design engineers retired from the mill industry. Similar conditions have existed in the last few years. This creates a loss of a tremendous amount of experience. This paper is a look back by two senior mill designers who survived the dips in both time periods. From a continuous design practice of over 25 years, mill designs and fabrication practices are surveyed with a view of identifying what works, and is necessary, and what doesn’t, or is not necessary, in the creation of a safe, economic, long-lived grinding mill.

Jan 1, 2001

By Phillip J. Mackey, Gerardo R. F. Alvear F.

It is now 38 years since the publication of the first edition of "Extractive Metallurgy of Copper" by Professor W.G. Davenport and the late Professor A.K. Biswas. The text book would be issued in a total of five editions, soon became the standard for students and those in industry. Interestingly it was published at the onset of great change in the industry. This was a time when sulphur dioxide controls in the USA were introduced, and almost simultaneously, world oil shocks caused significant increases in the cost of fuel - all leading to efforts to adopt new technology and move away from the reverberatory furnace, which had no potential for sulfur capture and required large amounts of fuel. At the time of publication of the book, new processes such as the Noranda Process and the Mitsubishi Process were in their infancy, while flash smelting (which was first commercialized in 1949 at Harjavalta, Finland) had made significant in-roads in boosting copper output, with some 22 new flash smelters licensed by 1976. Computer technology and associated process control techniques were rudimentary compared to systems today, available physico-chemical data remained largely in tabulated format and needed to be manually entered into the main frame computers of the era, while modeling techniques common today had not yet been developed. The copper industry has therefore seen immense changes since the time of this textbook: world tonnage of smelted copper has risen from 7.34 million tonnes/year in 1976 to 16.7 million tonnes/year in 2012, over a two times increase. Technologies such as the El Teniente Process, or Top Submerged Lance technologies, typified by the ISASMELTTM, not commercialized at the time, now treat large tonnages of copper concentrate in a single furnace. Advanced heat and mass balance software and thermochemical modeling are now used extensively to examine chemical and physical characteristics for process design and to support process optimization. These changes in the industry have been chronicled in subsequent editions of the book. This paper looks at the issues and problems seen in 1976 and over the intervening years, and compares this with the challenges facing the industry with the available tools and technologies today. Some ideas looking into the future are also discussed in the paper.

Jan 1, 2014

? Founded In 1953 ? Mining growth of 83% since 2007 ? We produced over 1 million ounces of Au in 2012 ? We Forecast of 20% Au production in 2013-2015 ? We have paid a dividend 31 years consecutively. Terry Reid ? 1992-93 Electrical Technical, College ? 1994-95 On the job placement College ? 1998 ? Licensed Millwright, ? 2005-12 ? Maintenance Reliability Planner ? 2012- Present Business Process Owner

Aug 1, 2013

By Les Johnston

_ BACKGROUND - About EPCOR - Genesee Generating Station - Phase 3 Expansion _ TECHNOLOGY SELECTION - Selection Criteria - Combustion Options - Flue Gas Emission Control Options _ STAKEHOLDER VIEWS _ PROJECT STATUS _ EPCOR is an integrated utility company for water, gas, electricity and technology services. _ EPCOR has about 1.6 million customers in Alberta, Ontario, Manitoba, BC, and the U.S. Pacific Northwest. _ EPCOR Generation Inc. operates three power stations in Alberta which were in operation before deregulation, including the coal-fired Genesee Generating Station. _ EPCOR Power Development Corporation owns generating stations in Alberta, BC and Washington State and will be building the Genesee Phase 3 expansion.

May 1, 2002

By Juan Garcia de Blas

O presente trabalho aborda o desenvolvimento de liga titânio-nióbio obtida por metalurgia do pó no qual foi introduzida uma operação de extrusão angular em canal (Equal Channel Angular Pressing - ECAP) com o propósito de promover uma consolidação que favorecesse a homogeneização na etapa posterior de sinterização. Após o processamento o material foi caracterizado por microscopia ótica e microscopia eletrônica de varredura (MEV/EDS). Os resultados preliminares indicaram a importância da redução do tamanho das partículas de nióbio.

Aug 17, 2017

By C. C. Clark

The national Institute for Occupational Safety and Health (NIOSH), Office of Mine Safety and Health, Ground Control Engineering Branch is investigating the use of shotcrete in weak rock mass mines with the objective of reducing fatalities and injuries resulting from rock fall accidents. When shotcrete is used as part of a multi-element ground support system, it is necessary to know when the material has developed a compressive strength of approximately 1 MPa (145 psi), the early threshold for safe re-entry of miner and machine into shotcreted mine workings at this value, the material has developed enough strength to be self-supporting and to allow for installation of other ground support components that require drilling of the shotcrete layer without degradation. NIOSH researchers have developed methods and portable test equipment to measure shotcrete strength on site in the first six hours after application using a partial beam test standard, a STM C 116-90 (1990). These advances were demonstrated in tests with five commercially available shotcrete mixes, sprayed as dry shotcrete using field expedient methods and equipment. The strength values from these tests allowed for real-time identification of the early strength threshold and were consistent with strengths reported using laboratory-type equipment. Measuring the early strength properties of shotcrete directly at the mine site can improve mine safety by identifying appropriate re-entry times and providing a convenient means of conducting on site quality control during shotcrete applications.

Jan 1, 2011

By Marius Jacobs

"Safety performance in many companies and even industries has stalled in the few years. Accidents rates are at a "plateau" and yet, serious accidents and fatality rates are not. In more dramatic cases, such as in the BP Texas disaster, organizations that have "exemplary" safety statistics, suddenly have a catastrophic or multi-fatality event occurring. Other classic examples are the Piper Alpha disaster and NASA’s Challenger and Columbia disasters and even the Chernobyl nuclear reactor. Looking into the root causes of these accidents provides an insight into the events and deficiencies that led up to the accident, but what are the common features in the organization’s mindset? What characterizes these organizations’ decision-making, their approach to safety and to risk and are there specific cultural features that can be delineated? The research and review presented in this paper covers a period since 1994, which started in the Australian resource industry and since then covered international events. The features of these organizations are summarized as the seven deadly delusions, based on extensiveresearch since 1997 of organizations that suffered unexpected disasters.The Piper Alpha Oil Rig disaster in the North Sea, on the 6 July 1988, was one of the most pivotal events in safety around the world. It changed the thinking and focus of governments, whole industries and led to numerous books and papers. It resulted in new legislation, textbooks and a critical self-examination by the oil and gas industry.In short, an explosion and fire occurred when a pipe started leaking gas and ignited. A temporary flange, with no safety valve, was used to block off this pipe during a maintenance operation the previous shift. The permit to advise operators not to start the pumps on this line was misplaced and lost. Several deficiencies, problems and system failures coincided. A key factor was that the water deluge system was inoperable at the time and failed to extinguish the large fire that erupted, followed by an even larger gas explosion. The accommodation unit, situated on top of the oil rig, was the main "killing field" - most men gathered here to await instructions (which never came) and where they died from smoke inhalation. Later, a large explosion of the gas pipeline from an adjoined rig exploded and killed more people.The line of events and the associated system failures are all very relevant in the analysis of the accident, and provide the only insight into what caused the accident. But much "further back", inside the organization’s culture, lurks more dark matter. The first inclination is to ask what was "deficient" in the culture. Did they not care enough about safety, or about their people? Did they have a culture where production decisions were more important than safety considerations? Did they ‘coerce’ supervisors and employees to ignore safety precautions or did they just "fly by the seat of their pants"?Not surprisingly, it is very difficult to identify the true nature of the culture in that business because in such an aftermath of death and destruction, no one dare say that the safety culture was a ‘positive one, focused and caring’ or that the company was doing well in safety and that this is only a freak accident. Indeed, there were many deficiencies in the organization’s systems and procedures, such as the permit to work system.But there are some niggling questions: How is then that the Piper Alpha Oil Rig was actually considered the company’s most productive and safest oil rig in the North Sea? Why would this rig win a safety competition, 6 months before the disaster, with the deficient permit as its most outstanding successful system?"

Jan 1, 2014

By Clement K. Chase

Since the dawn of cyanidation leaching techniques for precious metals, certain manganese-bearing silver ores have been a problem due to low silver extraction. Since simultaneous occurrence of silver and manganese is common in nature, this situation has made many otherwise attractive silver deposits uneconomic in the past. Several older techniques have been useful but at $1.29 per ounce of silver, the economics were unfavorable. With the new look in silver prices and some improvements in processing technology, neglected silver districts offer new promise.

Jan 1, 1981

By Brad Wells, Wayne Bull, Wayne Dickinson

"Antiscalants were evaluated for control of calcium carbonate (CaCO3) in gold processing applications. Under severely supersaturated conditions, 100 percent inhibition was achieved with 30 ppm antiscalant. Laboratory and field testing established that an antiscalant could both inhibit scale buildup and remove an estimated 0.5 kg/m2 per annum of pre-existing scale. A program was developed to control CaCO3 at a gold mill experiencing severe scale buildup. Annual accumulation of as much as 3 cm of scale in process piping was reduced to unmeasureable levels when 10 ppm antiscalant was applied. No scale-related upsets in mill operation occurred during a five-month trial period.INTRODUCTION Inorganic mineral scale is a crystalline deposit that forms when dissolved mineral constituents exceed the solubility of the respective mineral phase. Formation of mineral scale adversely affects a wide range of industries and is of particular interest in mining and metals processing. Scale affects numerous stages of metal extraction processes. Restricted flow in piping, nozzles, valves, screens, pumps and other components used to transport mineral slurries, metal concentrates, and tailings as well as scale in millwater and thickener overflow circuits are primary concerns (Alfano & Boffardi, 1994). Heap leaching, comminuation, flotation, vat leaching, carbon adsorption, and heat exchangers as well as oxidation steps used in processing sulfidic ores are among key unit operations that may be adversely affected (Simmons & Gathje, 2003). Antiscalant chemicals are designed to prevent formation and growth of mineral scales such as CaCO3. These chemicals, which include two primary classes – phosphonates and anionic carboxylate polymers and copolymers - are added to the gold processing stream at low parts-per-million (ppm) concentrations to interfere with nucleation and growth of scale forming crystals and to disperse fine particulate material. Application points may be located throughout the gold extraction process. Evaluation of the performance of antiscalants plays a critical role in determining the best product for a specific application. Performance evaluations include laboratory testing, pilot scale studies, in-plant trials, and ongoing performance monitoring during mill operation."

Jan 1, 2014

By Andrea McGlynn

Iron Ore Company of Canada, Labrador City 2011?Canada's largest iron ore producer, leading global supplier of iron ore pellets and concentrates ?Rio Tinto (58.7%), Mitsubishi Corporation (26.2%), Labrador Iron Ore Royalty Income Fund (15.1%)

May 1, 2011

By L. A. Thompson, A. J. Linington

"Copper–cobalt extraction is a reagent-intensive process resulting in acid consumption greatly contributing towards production costs, which in the current market conditions curtail profitability. Nanofiltration (NF) membranes have become an attractive approach in the mining and minerals industry for product concentration and reagent recovery based on the ability of the membrane to separate monovalent ions from divalent ions. NF membranes can selectively separate acids from metals and salts allowing acid to be recycled as well as the concentration and purification of product streams. Membrane technology in the field of copper–cobalt processing focusses on the concentration of Cu2+ and Co2+ in the pregnant leach solution, recovery of acid from waste streams to neutralization, recovery of valuable metals from waste ponds and process water recovery. This paper aims to provide insight into the potential applications of NF membranes in copper–cobalt processing circuits as well as a brief overview of the effects of process conditions on membrane performance and process development. INTRODUCTION The copper–cobalt industry commonly uses inorganic acids, such as sulfuric acid, in large quantities for primary leaching of copper–cobalt oxide ores and releaching during product purification (Stuurman et al., 2014). This results in numerous acidic intermediate streams containing high metal concentrations and acidic waste streams with low metal concentrations. Acid consumption typically accounts for 10–15% of the operating costs of mines in the Democratic Republic of Congo (DRC) and Zambia (Acid Plant Database, 2015). Due to remote mine locations, poorly maintained roads and cross-border conflict, the cost of sulphuric acid can range between USD 300 and 400 per ton. The pivotal role of acid in the copper–cobalt extraction process has driven many mines to build sulphuric acid plants on site to ensure a reliable acid supply, however elemental sulphur still needs to be imported which faces similar logistical challenges and contributes towards operating costs."

Jan 1, 2015

This paper aims to collate the metallurgical test work undertaken on the Barrytown mineral sands deposit. It is intended to serve as a summary of mineral dressing work undertaken by all interested parties up to the time of writing. Areas requiring further investigation are: in situ grades and recoveries of accessory minerals,the question of 'rank' of ilmenite within the deposit,flow sheet development for the recovery of gold and monazite, andcost analysis to investigate the relative worth of other minerals; notably rutile. Flow sheet development with respect to the Accessory Minerals cannot be accurately defined until the importance of each mineral in terms of grade, recovery and expected revenue is determined. To date, ilmenite and zircon flows are well documented. Further work is needed to quantify recovery's and flows of the other minerals; notably monazite, gold and rutile.

Jan 1, 1989

By Kevin M. Ansdell, Irvine R. Annesley, Christine L. Mckechnie

The U-Th-REE mineralization at Fraser Lakes Zone B is hosted by granitic pegmatites and leucogranites, which lie along the deformed contact between Paleoproterozoic metasedimentary gneiss of the Wollaston Group and Archean orthogneiss, approximately 25 km from the southeastern edge of the Athabasca Basin. The pegmatites/leucogranites are subcordant to concordant with the regional foliation and are concentrated within a northeast-plunging antiformal fold nose, the study area, which lies west of Fraser Lakes. The mineralized pegmatites/leucogranites in the western part of the study area (Group A) are typically enriched in U (± Th) with Th/U ~1, and contain uraninite, thorite, zircon, and allanite. Those intruding the central part of the study area (Group B) are generally enriched in Th and LREE, with Th/U >2, and contain monazite, thorite (commonly U-enriched), and zircon. The pegmatites and leucogranites in Group A tend to be slightly enriched in SiO2 and depleted in TiO2 relative to those in Group B and are interpreted to represent more evolved crustal melts. Both groups are peraluminous and show varied chemistry. Partial melting (~850ºC and 9 kbar) of a metasedimentary rock-dominated source, entrainment of accessory minerals as xenocrysts, and assimilation-fractional crystallization processes combined to enrich the granitic pegmatites/leucogranites in U, Th, and REE elements. Transfer of melt from the source region to the crystallization sites was assisted by deformation within and along major structural zones, such as the folded Archean-Paleoproterozoic discontinuity. The character of mineralization and structural control in the study area is reminiscent of the alaskite-hosted deposits at Rössing, Namibia.

Jan 1, 2013

By Marty Hudyma

Large seismic events have been reported in mines in the Sudbury mining camp for more than 70 years. Nevertheless, no detailed record of the events has been compiled. In 2008, the Sudbury Regional Seismic Network (SRSN) research project was initiated to collect more accurate data with regard to the magnitude and locations of mining-induced seismic events in and near the mines in the Sudbury Basin. The data is used to better understand the mechanisms of the events and cause-effect relations between mining and seismic events. Through the collection of a central database of large seismic events, new insight is being be gained into why some mines are much more prone to large events than others. Fifteen low cost seismic stations have been distributed throughout the Sudbury basin. The data from each seismic station is uploaded to a central server using the internet. Data recorded on the SRSN is processed on a daily basis, and a weekly summary of blasts and events is issued to project sponsors. Seismic events smaller than local magnitude +1.0 have been identified and located. Event location accuracy is less than 2 kilometres, however, many events have been located less than 1 km from a mine. The SRSN fills a seismic monitoring gap between the in-mine microseismic monitoring systems and the earthquake monitoring system operated by the Geological Survey of Canada. Since July 2008, more than 600 mine blasts and more than 450 mining-induced seismic events have been recorded in the Sudbury basin. This paper primarily discusses the technical aspects of the design and operation of the SRSN. The SRSN is a Canadian Mining Industry Research Organisation (CAMIRO) research project, with industry sponsorship and support from FNX Mining, Itasca Canada, Vale Inco and Xstrata Nickel.

Oct 1, 2010

By R L. Brathwaite

Previous paleodepth studies of low-sulphidation epithermal Au-Ag deposits in the Coromandel region indicated that economic gold mineralisation was generally limited to a depth zone of 100 to 400 m below the paleosurface. Notable exceptions are Waihi and Karangahake, where ore shoots extended to depths of about 750 and 900 m respectively. These studies have been extended to include Au-Ag, Hg and Sb epithermal deposits in Northland and the Taupo Volcanic Zone. The main paleodepth indicators used are sinters and hydrothermal eruption breccias, hydrostatic pressures estimated from homogenisation temperature measurements on fluid inclusions, and hydrothermal alteration mineralogy. Also the occurrence of lacustrine and fluvial sediments is an indicator of the paleosurface at their time of deposition. Selected paleodepth indicators have been compiled and mapped in a GIS environment. The distribution of the paleodepth indicators are used to define regional variations in erosion levels, and may be useful in predicting areas most likely to preserve the optimum depth window for gold deposition. In the Coromandel region, regional stream sediment geochemical data has also been used to broadly define erosion levels in terms of Zn, Pb and Cu representing deeper base metal zone mineralization and Hg and Sb representing shallower cinnabar and stibnite mineralisation. The interpretations of paleodepth and potential reconstruction of paleosurfaces are limited by the paucity of data, poor age control on the paleodepth indicators and the epithermal deposits, and marked relief and complex stratigraphy in the volcanic terranes.

Jan 1, 2003