Search Documents

By Ananta L. Yennamani

Blast movement measurement (BMM) transmitters are a practical method to measure three-dimensional (3D) rock movement because of blasting. The BMM transmitters are activated, programmed and installed in specially designed drill holes prior to the blast and the BMM detector locates the transmitters after the blast. The BMM software then calculates and summarizes the 3D movement of each BMM transmitter ball. This information helps to redefine the ore and waste boundaries and enables improved ore and waste selection, resulting in a genuine step change in grade control. The BMM program was carried out at Newmont Mining Corp.?s Phoenix Mine, in northern Nevada near the town of Battle Mountain. The mine is in a historic mining district that contains gold, silver and copper. The geology of the pit consists of different formations made up of sandstone, siltstone, limestone, chert-pebble conglomerate, shale, skarn and quartzite, to name a few. Some of the rock is extremely hard and a powder factor of up to 0.5 kg/t (1 lb/st) is required to get adequate fragmentation to ensure sufficient throughput through the crusher and the mill. The result of using such a high powder factor translates into considerable blast movement and heave. This movement means that the ore/waste digging polygons estimated by the ore control engineer from sampling the initial blast holes will no longer be located in their original posi-tions. The purpose of this project was to test the measurement method and to see if locating the digging polygons in the broken muck pile and excavating to those polygons will improve grade control through the mill. Case studies (Zhang, 1994), (Taylor, 1995), (Gilbride, 1995), (Harris, 1997), (Taylor, 2003), Barrick Goldstrike (Gold-strike Mine, 2008), Ruby Hill Mine (Hilkewich, 2009), (Porcupine Mine, 2005) and (Aguirre, 2010) have shown that, by accounting for the blast movement, there is a potential to increase mineral recovery by as much as 25 percent for individual blasts for only a modest cost increase.

Jan 1, 2011

By G. ALBORNOZ, S. Utili, A. AGOSTI, C. VALDERRAMA, R. PELL, N. Morales

The steepness of the slopes of an open pit mine has a substantial influence on the financial return of the mine. The paper proposes a novel design methodology where overall steeper pitwalls are employed without compromising the safety of the mine. In current design practice pitwall profiles are often planar in crosssection and the profile in between ramps especially tend to be planar and defined by a constant inter-ramp angle. Sometimes rock layers exhibiting different strengths require the inclination of the profile to vary with depth, but the inclination across each layer is usually constant. Here instead, a new geotechnical software, OptimalSlope, is employed to determine optimal pitwall profiles of depth varying inclination. OptimalSlope seeks the solution of a mathematical optimization problem where the overall steepness of the pitwall, from crest to toe, is maximized for an assigned lithology, geotechnical properties and Factor of Safety (FoS). Bench geometries (bench height, face inclination, minimum berm width) are imposed in the optimization as constraints which bind the maximum local inclination of the sought optimal profile together with any other constraints such as geological discontinuities that may influence slope failure. The obtained optimal profiles are always steeper than their planar counterparts (i.e. the planar profiles exhibiting the same FoS) up to 8 degrees depending on rock type and severity of constraints on local inclinations. The design of a copper mine is first carried out employing planar pitwalls, secondly adopting the optimal pitwall profiles determined by OptimalSlope. The adoption of optimal slope profiles leads to a 34% higher net present value and reductions of carbon footprint and energy consumption of 0.17 Mt CO2 eq and 82.5 million MJ respectively due to a 15% reduction of rockwaste volume.

Mar 2, 2022

By Jean-François Boulanger

The production of rare earth elements from ore usually consists of three steps; the separation of a concentrate of REE bearing minerals; the cracking of the REE minerals to liberate the REE into an aqueous solution and separation of REE into individual elements. This paper describes the results of laboratory tests conducted on a carbonate-rich REE ore containing bastnaesite and monazite. The tests cover the whole processing sequence of beneficiation, preparation of the REE solution using a caustic leach followed by acid leach to break monazite and bastnaesite and liberate REE into an aqueous solution and the partial separation of the REE using solvent extraction. Details on the product quality and process performances (recovery and impurities removal) are given for each studied step. The paper also discusses the economic advantage of separating the REE rather than producing a mixed REO product to be sold to a refinery for REE separation. A mini-pilot plant version of the process is currently planned.

By Mackenzie Burnett

This program was initiated by USBM to quantify the respirable dust problem caused by the use .of roadheaders in underground metal/nonmetal mines with special emphasis on this problem in uranium mines. The contract called for the development of methods or equipment to alleviate the respirable dust and to implement the solution in a mine. Attempts to quantify the dust problem were made in the following way: survey of MSHA records, survey of state mine enforcement agencies, survey of mine records, dust measurements taken at two mines using roadheaders. The results of this study are not conclusive due to very limited and sometimes less than useful data; however, the study does indicate that a serious dust problem could and may exist. If and when roadheader use becomes more popular, it is almost certain that development of dust control procedures and equipment will be necessary. This contract was concluded without developing this equipment since only one roadheader is currently in use in an American uranium mine and the mine prefers not to participate in the program at this time. This report discusses the available data concerning respirable dust problems and presents a solution which can potentially help to solve the problem. The solution requires the use of blowing ventilation, on-board dust extraction at the source, and filtration, as well as continued use of water sprays. The on-site tuning of such a system is necessary to demonstrate the degree of improvement possible.

Jan 1, 1981

By Aníbal Gatañaga Coll

Dada la peligrosidad del sílice libre como principal problema en el campo de la higiene industrial, el objetivo del trabajo es controlar y evaluar la concentración de dichos polvos a través del uso de tres métodos: El método químico, el de difracción de rayos X y el petrográfico. El primero (N. A. Talvitie), utiliza un reactivo que descompone y disuelve a todos los constituyentes de la muestra, excepto al cuarzo, quedando calcinado y filtrado; el segundo método es eficaz, pero requiere de un equipo muy costoso, mientras que el método petrográfico muestra una mejor identificación de los minerales, determinando las cualidades de los materiales que se producen en la composición del polvo, así como precisa la pequeñez de las partículas encontradas en los polvos industriales y sobre todo de la capacidad del operador.

Jul 20, 1955

By R. J. Craig

Introduction All mining operations produce rock dust. Inhalation of rock dust, particularly if it has a high silica content, causes silicosis. Silicosis is, therefore, recognized as a hazard of the mining industry and has been made compensable throughout most of Canada. Most of the dust in any mining operation is caused by rock drilling and blasting operations and the movement and transportation of broken rock. Dust from blasting cannot be eliminated, but it can be controlled by means of increased ventilation, the use of water sprays, and the control of blasting hours. Dust from ore movement can be reduced by keeping the broken rock in a moist condition at all times. The dust from the rock drilling operation has been found to be the most difficult to control. Concentrations of dust caused by rock drills in stopes can usually be reduced to the safe minimum of 300 particles per cubic centimeter (p.p.c.c.) by diluting the air with increased ventilation. In development headings, where the machines are more confined, this is not always practicable. Therefore, the dust must be eliminated at its source. This paper deals with the reduction of dust from Leyner machines by adopting improved designs.

Jan 1, 1947

By W. G. Miller, J. D. Scott, D. C. Sego

ABSTRACT An overall study was conducted to evaluate the properties and processes influencing the rate and magnitude of consolidation for oil sands fine tailings produced using different extraction processes. As part of the overall study, a comprehensive description of physical and chemical characteristics of fine tailings generated by caustic and non-caustic processes was carried out. Ultimately, the influence of these fundamental properties on the compressibility, hydraulic conductivity and shear strength properties of the fine tailings was assessed. The characteristics of the fine tailings are presented in terms of index properties, mineralogy, specific surface area, water chemistry, liquid limits, particle size distribution and structure. A difference in water chemistry was concluded to be the cause of substantial differences in particle size distributions and degree of dispersion of the comparable caustic and non-caustic fine tailings. The degree of dispersion was consistent with predictions for dispersed clays established by the sodium adsorption ratio (SAR) values for these materials. A linear variation of increasing dispersion with increasing SAR up to a SAR value of about 40 has been suggested, above which fine tailings are completely dispersed. The observed dispersed or flocculated structures (viewed using a scanning electron microscope) supported the predictions based on SAR values.

Jan 1, 2010

By Margaret R. Egan

The Bureau of Mines experimentally burned Pittsburgh Seam coal and other combustible materials found in mines in order to obtain a better knowledge of their emission products. These experiments were conducted in the Bureau's intermediate-scale fire tunnel, which simulates environ-mental conditions in underground mines. Smoke characteristics, gas concentrations, mass loss, and ventilation were measured. From these values, heat-release rates, particle sizes, obscuration rates, combustion yields, and production constants were calculated. This information was sought as part of a comprehensive study of combustible materials that will ultimately advance the design of more efficient fire detection and suppression systems. The coal combustion measurements presented in this report, together with previous analyses of wood and transformer fluid fires form a data base by which future studies of other mine combustibles can be compared.

Jan 1, 1987

By Jack Craft

Local Environment Atmospheric conditions (or lack thereof) Drilling fluids are impractical Cuttings removal is a major concern Heat dissipation is a major concern Some tried-and-true mechanisms need air to function properly Gravity Low gravity means low downforce Microgravity means even less downforce Regolith Local dust may be highly abrasive Packaging for Spaceflight System mass is highly constrained The drill must fit within the spacecraft?s launch envelope Power is constrained

May 1, 2013

By Ludwig Schmidt

This report, the second of a series, presents the results of laboratory corrosion studies which were made in connection with a one-year test on aluminum lease tanks conducted by the United States Bureau of Mines. Part I of the report contains the results of the field teats.5 The studies were made on an oil lease in a so-called "sour district," near Borger, Tag., where free hydrogen sulphide accompanied the production of oil, gas, and salt water. Steel tanks previously used on the lease had suffered severe corrosion, because steel is inherently susceptible to attack by hydrogen sulphide. Because of the high resistivity of aluminum to the action of hydrogen sulphide, it Was believed that this metal had promising possibilities as a material for the construction of lease tanks in "sour districts." The results of the one-year field teat proved that aluminum lease tanks will withstand corrosion by hydrogen sulphide, but it was found that aluminum was susceptible to attack by salt water, which was invariably present in certain portions of the tanks, and that hydrogen sulphide accelerated this salt-water corrosion in an indirect manner, as will be explained hereinafter. In order to study corrosion conditions encountered in the tanks during the test period, a laboratory was maintained at the site of the aluminum lease tanks.

Jan 1, 1931

By J Franz, S Bock, N Hentrich

Artificial ground freezing is the unrivalled method for groundwater control during mine shaft sinking. Moreover, ground freezing may also provide temporary ground support. The fast development of fibre-optic temperature monitoring devices, three-dimensional freeze pipe survey methods and numerical modelling software provide grounds for developing new and reliable tools for ground control during freeze shaft sinking. This paper presents examples of predictive numerical models that are based on back-analysis and calibration of temperature data that covers the complete construction cycle from pre-freezing through to artificial thawing. The back-analyses showed that standard numerical models are not capable of predicting the prevailing thermo-mechanical conditions satisfactorily. This paper describes the development and implementation of new tools for improved consideration of concrete hydration and latent heat, along with the introduction of other algorithms that improve and simplify the efforts of managing complex numerical models. A function is presented that allows for an automated correction of the model’s mesh based on results of three-dimensional freeze pipe surveys. This paper demonstrates that the latter consideration is important, because the often employed assumption of idealised freeze circle geometry in numerical models impacts on the accuracy of such model’s predictions. Subsequently, the verification of these extended numerical models is demonstrated. Due to its flexibility, the FLAC3DTM code was employed for the numerical modelling. This software provides the possibility of implementing additional functions written in internal FISH or Python language into the models. It is concluded that state-of-the-art techniques for freeze hole drilling and surveying, on-site monitoring and advanced numerical analysis provide a significant potential for both the design and the operation of largescale ground freezing measures. The application of the extended numerical models for predictive simulations during construction allows for temporary shaft lining optimisation, for assisting in operational decision making and for compensating temporary loss of monitoring data. Suggestions are made for required future work in order to further improve the developed ground control tools. CITATION:Bock, S, Franz, J and Hentrich, N, 2018. New tools for ground control in freeze shaft sinking, in Proceedings The Fourth Australasian Ground Control in Mining Conference (AusRock), pp 393–406 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Nov 30, 2018

By F. G. Miller

[Petroleum tscknologists nnd progressive operatorr. constantly are striving to increase the percentage of oil thnt may be recorered from reservoir rocks through wells. The exhaustive studies that hve boen made of the function of natural gas in the production of oil, for example, havo aided operators greatly in increasing tho quantity of oil recovered from reservoirs. Natural gas dissolv.3d in and otheraiso asnociatod under pressuro with oil in rsservoir rocks, howovor, is not tho only source of energy available for rnovi~~ oil through sands to wells. In becomine Veservoi~enorgy conscious^^ encineera havo lonrned that in nnny petroleum resorroirs the edgewater flanking the oil accurrulation constitutos a potantinl source of enorgy cnpnblo, through pro1,sr control, of increasing oil-recovory officioncies materially. ?To longer is tho oncronchmont of mter into the oil- and gas-fillod uart of tho reservoir conridsred as evil to be combatted by dovious mothods but rnthar a nrtturrtl consequence, incident to the withdraval of oil nna gas from tho rolls, thnt mP.y be used nd~~mtngeoualy in lengthening the flowing life of wells ,md incre~sing the oconornic recovery nf oil and gns. Little is knom a3out tho nac'n-~nisrn by mhich wnter qor-rtos in driving nil through reservoir rocks, nnd thjro is n scnrcity of published informa- tion on rates of rnovzrnant of ~ntcr +,hat will result in naxilnm oil recoveries. Bureau of Xine s er.gir.ess nr r'reciate the ~aucity of scientific knowledge on the best methods of lying the natural rater drive to in- crease oil-recovery efficiencies arid ar9 initiating stildies that rill, they hope, contributo to tho procont small fund of information now available on the subject. This rh~.ort is s syr,o_nsis or brief c03pilation of published dAta and thought nccumulntod 30 far, groliminary to la-uorgtory ox~eriment+ tion NI& further resaarch on the principlgs und~rlying the nnturnl wnter drive RS it nffocts oil rocovory. The vrritors hopo th2t the omosition of available information prosentod in tho rey~ort rill stindate constructive thought and efforts loading torard moro comrlote extraction of oil and gas from resorvoirs.]

Jan 1, 1938

By H. X. Li, A. Correa, M. M. Zhang, W. Xuan, M. Andrade

"With increasing demand for steel and depletion of high-grade iron ore deposits, more research efforts are being directed toward extending the life of existing ore reserves and developing technology to treat low-grade iron ore resources. Among all the reported technologies, biotechnologies in mineral processing – specifically bioleaching and microbially induced flotation – have emerged to be considered as low-cost, environmentally friendly potential alternatives to many of the current mineral processing techniques. This paper provides a comprehensive review of current research on the use of microorganisms for iron ore beneficiation and, further, discusses the applicability of bioleaching, bioflotation and bioflocculation for the beneficiation of low-grade iron ores.IntroductionIncreasing global demand for raw materials has led to diminishing resources of high-grade iron ore. As a result, the mining and utilization of low-grade hematite, limonite, specularite, siderite and goethite ores have attracted more and more attention. However, these types of iron ores are of complex paragenesis and fine disseminated grain size, and often contaminated by phosphorus in the form of solid solution. The distribution of phosphorus throughout the iron mineral crystals prevents the effective use of physical separation techniques, and these complex ores are at present largely untapped due to a lack of cost-effective and efficient processing methods. Chemical leaching and roasting-magnetic separation approaches have been mainly tested only on the laboratory scale and are all either cost prohibitive or ineffective when used on low-grade complex iron ores."

Jan 1, 2015

By William F. Hahn

The Bureau of Mines recognized the problems encountered in low seam mining illumination systems. It was determined that the best way of implementing an illumination system is to integrate the design during the design and fabrication of new machinery at the factory. The purpose of this program was to integrate an approved lighting system in a low seam battery powered scoop and evaluate its performance. This report documents the work performed on this program and the results obtained.

Jan 1, 1980

By A. C. Richardson

[During the past two and a half sears the U. S. Bureau of Mines and the University of Alabama, with the cooperation of the different coal operators, have been making an extensive studs of coal preparation in the State of Alabama. Considerable time has been devoted to the studs of the washing characteristics of the Mars Lee bed and the various methods used In preparing from it a low-ash coal suitable for the manufacture of metallurgical coke. One of the phases of this problem is the utilization of middlings products from the washing plants. This paper gives the results of treating jig middlings on a coal-washing table at the Bureau of Mines laboratory at Tuscaloosa, Ala. The sample used was secured from the Sayreton washery of the Republic Steel Corporation, Sayreton, Ala. WASHERY PRACTICE The Mary Lee bed is very bony, and operators find it difficult to produce from this bed a washed coal much under 10 per cent ash. Experience has shown that in the preparation of a coking coal from the Mary Lee bed it is best to use a process which permits the recovery of a middlings product. Middlings are desirable because separation according to specific gravity is never perfect, and a middlings product makes possible a low ash in the primary warned coal without excessive losses of combustible in the refuse. The general washery practice on the Mary Lee bed is to crush the run-of-mine coal through some maximum screen size and wash it upon some one type of jig without re-treatment of any of the products made. The maximum size treated varies from 3 inch to J inch. The middlings product from multiple-cell jigs is usually termed "boiler fuel" and when possible is utilized as such. At present the production of boiler fuel is often in excess of power requirements, and the surplus, due to its high ash content, becomes waste.]

Jan 1, 1931

By M Brady, O Salisbury, C Claassen, B Beamish, H Baxter

Monitoring for signs of elevated spontaneous combustion in the active goaf behind the longwall face is crucial for early intervention of any potential heating incidents. Typically, trigger action response plans (TARPs) are established at the start of longwall mining and often are only reviewed when triggers are activated frequently and become ‘nuisance alarms’, or in the worst case scenario after a heating event. Narrabri Mine has adopted a proactive approach of reviewing the longwall active goaf spontaneous combustion monitoring TARP at the commencement of each longwall block and prior to reaching a known ‘mylonite zone’ of crushed coal, which is associated with increased coal oxidation. The review is based on information recorded from the monitoring data of the previous longwall blocks as well as interpretation of relevant spontaneous combustion propensity results for the coal. This has resulted in the mine implementing a zoned TARP approach for each longwall block covering both the longwall retreat through normal undisturbed coal and the zone where the goaf is influenced by the increased coal oxidation associated with the mylonite coal. The consequence of this approach is that it has removed the issue of having nuisance triggers being activated during mining through a known increased oxidation zone, while maintaining a high awareness of indicators of spontaneous combustion.CITATION:Baxter, H, Claassen, C, Salisbury, O, Brady, M and Beamish, B, 2015. Implementation of a zoned trigger action response plan associated with changing mine conditions at Narrabri Mine, in Proceedings The Australian Mine Ventilation Conference, pp 113–120 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 31, 2015

By Martin J. Gavin

"Before discussing oil shales it may be well to consider briefly the conditions surrounding the petroleum industry in the United States, because these largely explain why so much interest is being manifested in oil shales. The United States is not only the greatest producer of petroleum in the world, its output amounting to about 65 per cent of the world's total production; but is also the world's greatest consumer, using more petroleum than it produces within its own borders. For the past four or five years it has been necessary to import oil at a continually increasing rate to make up the deficit between domestic production and domestic consumption. Experts who have made a close study of the future supply and demand for, crude petroleum are satisfied that under present production practice and with the development of possible undeveloped productive areas, the gap between domestic consumption and production will steadily .increase.As possible solutions for the impending domestic shortage of oil, various expedients are receiving attention. These may be grouped under three heads, as follows:(1) Temporary measures, such as curtailment of consumption, development of more efficient methods of production, and more efficient utilization of supplies of petroleum still available. It is unlikely that there will be any great curtailment in consumption of petroleum in the United States; rather, consumption will continue to increase unless a real shortage of oil actually forces curtailment of consumption. The other two possibilities mentioned deserve, and are resolving, serious thought. Much experimental work along these lines, some of which has already yielded excellent results, is being done. Obviously, however, any of these remedies are temporary ones only, so far as regards domestic production of petroleum."

Oct 1, 1920

By John Beaumont

The Plate-Steckel mill combines the asset utilization of the strip rolling process with the grade and width range of the reversing plate mill, delivering a broad range of steel products at low cost. Among rolling mill types, plate mills are distinctive in the way that they exploit the metallurgical attributes of their product. The downside of this flexibility, though, is a low level of asset utilization. The Plate-Steckel mill was originally developed to combine the utilization of the strip mill and the width of the plate mill. The Plate-Steckel mill is now setting new benchmarks in accessible grades and applications, whilst pushing the width boundaries of the process. Long experience in the Steckel process control and coiler furnace design is coupled with caster and plate mill expertise to deliver high level of performance in this increasingly important plate and coil rolling technique. Several new design features have been incorporated and the vertical integration of mechanics with process models is the key for better product quality and flexibility at these plants. The use of fully automatic thermo-mechanical rolling using the latest physical models and intelligent sequencing strategies achieves the optimum grain refinement and thus improves mechanical properties. The novel profile and flatness strategy relies on comprehensive physical models and makes use of SmartCrown® as a powerful actuator, enabling large reductions to be taken without risking poor flatness. Throughout the rolling and cooling stages of processing, accurate calculation of the thermal-mechanical state of the product is performed by the temperature monitor. This enables tighter control of the final plate mechanical properties by providing an insight into the plate evolution during the thermo-mechanical processing. Advanced pacing functionalities provide an optimized mill throughput, utilizing new cooling bed charging strategies. Considering the rolling process, process automation applies state-of-the-art model calculations to achieve saleable coil/plate target dimensions even in non steady state rolling conditions.

Aug 16, 2017

By Shu Xinqian, Zhou Weining, Shan Zhiqiang, Feng Jifu

"Modified calcination conditions on the extraction of rubidium resources from muscovite (KAlz[AlSi301o](OH)2) ore are systematically studied. The impact of various factors on the rubidium leaching rate is also analyzed, including the agent types, roasting time, the mass ratio, roasting temperature, etc. The results indicate that the best agent is a combination of sodium chloride and calcium chloride, its mass ratio ofmuscovite/NaCl/CaClz is 1:0.25:0.25. Calcined at 8500 for 30 minutes, the rubidium leaching rate is up to 90%. The reaction of muscovite ore with the chlorinating agent CaC12 has been studied by TG/DSC, the calcined intermediates are identified by XRD, and the surface morphology before and after leaching is characterized by SEM. Rubidium chloride products can be obtained with a purity of 92% by using t-BAMBP extraction, hydrochloric acid reextraction and purification.IntroductionRubidium is one ofrare alkali metals, which is found in 1981 by German R.W. Bunsen and G.R. Kirchhof. Rubidium includes the following features: atomic number is 37, each atom weight 85, the body-centred cubic lattice, each unit cell has two metal atoms, and the density is 1.532g/cm3. The properties of low melting point (312.46 K) and malleability make rubidium have a strong chemical activity and photoemission. Rubidium provides a main material for manufacturing phototube with a wide range oflight waves, which possess high sensitivity and stability. Efforts are being made to carry out research on rubidium ion gngine, magnetic flux generators and thermoelectric transudcer, etc. Rubidium exists in muscovite ore(KA12[AlSh01o](OH)2 (monoclinic system and hexagonal layered structure) as isomorphism and replace the large radius of the potassium atoms, as well as part of rubidium locate between structure layers. The complex components bring great difficulty in comprehensive recycling."

Jan 1, 2013

By C. S. Parsons

Introduction Up to the present, the operation of small mills for the treatment of gold ores has not been favoured in Canada to the extent that it has in other countries. For instance, a list of the operating properties in Southern Rhodesia, published in The Rhodesian Mining Journal of November, 1934, shows for the month of September, 1934, that there were over 500 small mills treating less than 50 tons per day, and the majority of these between 5 and 25 tons. They are operated by individuals, syndicates, and small mining companies. It is presumed that the operations are profitable, although from the published figures of the tonnages treated and the yields, it is difficult for one familiar with Canadian operations to understand how this can be possible, in the majority of cases. Most of these small mills employ stamps with plate amalgamation and with, occasionally, tables to produce a concentrate. Enquiries have been received from many parts of the world respecting milling practice suitable for small gold mines and the type of plant used in Canada. The tenor of these enquiries leaves the impression that the majority of the writers assume that the practice would be similar at all small properties. This, of course, is not the case. Conditions vary widely, and what would be a suitable mill for a typical Nova Scotia ore would not necessarily be wholly adaptable to many ores in Ontario, Quebec, or British Columbia. This paper has been written with the intention of inviting discussion, and it is hoped that, by such discussion, the subject will be more fully dealt with than has been possible in the time at the disposal of the writer. Only more or less standard principles and practices have been dealt with, and, purposely, no reference has been made to plants using mills of the Hadsel, the Nutt, or the Gibson type. As there is available but little reliable information on the costs of installation and operation of small mills, it is also hoped that those contributing to the discussion of milling practices for small mines will be in a position to give these data for the benefit of those contemplating the erection of small plants in Canada. Although it is difficult to generalize, it can be said that there are three types of gold mills commonly used at small mines: (1) Amalgamation and Gravity Concentration; (2) Amalgamation and Flotation; and (3) Cyanidation.

Jan 1, 1935