Search Documents

By M. M. Zarnan

This paper presents the results of s study involving characterization of ground subsidence of abandoned lead-zinc mines in northeastern Oklahoma. Two coordinated efforts were undertaken: (1) collection and analysis of available data such as driller's logs, geologic cross-sections, structure contour naps and stratigraphic sections, and (2) development of a numerical (finite element) technique for prediction of collapse and mine subsidence. An in-depth analysis of a major collapse in the region was conducted. The factors which contributed to this collapse were identified.

Jan 1, 1989

By M. Drozd, A. Ibrado, P. Butcher

While effective in treating refractory sulfide ores, pressure oxidation leaves carbonaceous matter unscathed and able to adsorb gold from cyanide solutions. Barrick Goldstrike's strategy to mitigate this problem is to minimize contact between dissolved gold and native carbon in advance of the carbon-in-leach (CIL) process. Measures currently in use include limiting carbonaceous matter in the plant feed by meticulous blending of ore, controlling the degree of oxidation in the autoclaves and blinding native carbon surfaces with lauryl sulfate. The presence of residual cyanide and thiocyanate in the process water remains to be a cause of premature gold dissolution and loss of gold by adsorption on carbonaceous matter. This cyanide is introduced by water that is recycled from the tailing pond. Of several treatment options considered, oxidation by peroxymonosulfuric acid, also known as Caro's acid, is deemed to be the most effective. Laboratory and pilot plant tests show that Caro's acid can oxidize free cyanide, weak¬acid-dissociable (WAD) cyanide and thiocyanate, resulting in significant improvements in gold recovery downstream. The process requires Caro's acid at 125 % of the stoichiometric requirement and pH in the range of 9.5 to 10 to accomplish the desired destruction in about twenty minutes. A cyanide destruction plant is currently being designed and construction should be completed by the end of 2005.

Jan 1, 2005

By R. W. Watson, H. D. Peer

"This paper outlines the history of steel linings in the Autogenous Mills, the factors influencing the decision to convert to rubber lining, and the operating and cost experience with the rubber liners to date. INTRODUCTIONSherman Mine is an open pit iron ore mining, concentrating and pelletizing operation located at Temagami, Ontario. The operation employs 392 hourly employees and 81 salaried employees and has an annual capacity of over one million L.T. of high quality iron ore pellets produced from low-grade magnetite ore.The Sherman Mine is a joint venture; 90% owned by Dominion Foundries and Steel Limited (Dofasco) of Hamilton, Ontario, and 10% owned by the Tetapaga Mining Company, a wholly-owned subsidiary of the Cleveland Cliffs Iron Company of Cleveland, Ohio. The operation and management of the mine is by Cliffs of Canada, Limited. Development of the property was started in 1965, with pellet plant production beginning on March 17, 1968. At the present time, the orebodies contain sufficient reserves to sustain operations at current production levels for 30 years. Mining was originally carried out in three orebodies, the North, South, and West pits. The North Pit has been exhausted and mining operations ceased in the spring of 1980. A fourth pit, the East Pit, will be developed during the early 1980's."

Jan 1, 1981

By Qingming Feng, Bo Huang, Dongbo An, Jinhong Zhang

A study of the application of mine tailings as precast construction materials through alkali activation has been carried out, focusing on efficiently activating mine tailings, reducing alkali consumption, decreasing curing time and improving compressive strength. Firstly, the effect of temperature on the alkali activation of mine tailings was studied. Secondly, the impact of additives, i.e., calcium hydroxide and aluminum oxide, on the compressive strength of samples was investigated. Thirdly, the impact of forming pressure on sample strength was studied. Test results showed that unconfined compressive strength (UCS) of 40 MPa was achieved with the geopolymerization products through optimization. Finally, to elucidate the geopolymerization mechanism of mine tailings, microscopic and spectroscopic techniques including SEM/EDX, XRD, and FTIR spectroscopy were used to investigate the microstructure and the elemental and phase composition of the geopolymerization products. The findings of the present work provide a practical method for applying mine tailings as precast construction materials through alkali activation.

By Qingming Feng, Bo Huang, Dongbo An, Jinhong Zhang

A study of the application of mine tailings as precast construction materials through alkali activation has been carried out, focusing on efficiently activating mine tailings, reducing alkali consumption, decreasing curing time and improving compressive strength. Firstly, the effect of temperature on the alkali activation of mine tailings was studied. Secondly, the impact of additives, i.e., calcium hydroxide and aluminum oxide, on the compressive strength of samples was investigated. Thirdly, the impact of forming pressure on sample strength was studied. Test results showed that unconfined compressive strength (UCS) of 40 MPa was achieved with the geopolymerization products through optimization. Finally, to elucidate the geopolymerization mechanism of mine tailings, microscopic and spectroscopic techniques including SEM/EDX, XRD, and FTIR spectroscopy were used to investigate the microstructure and the elemental and phase composition of the geopolymerization products. The findings of the present work provide a practical method for applying mine tailings as precast construction materials through alkali activation.

"1 INTRODUCTIONThe use of nondestructive testing (NDT) methods to evaluate the integrity of Augered Cast-in-Place (ACIP) and Drilled Displacement (DD) piles has been a subject of significant debate among engineers, contractors and NDT practitioners. This guideline document will illustrate the importance of reviewing all available information in conjunction with the NDT records. ACIP and DD piles have unique properties that must be considered when using a specific NDT method. Any evaluation of the integrity of an ACIP or DD pile must also include a thorough review of the detailed pile installation records and the site specific soil conditions. Long or theoretical descriptions of the methods have not been included in this publication. More detailed information about these NDT methods including their theoretical and historical backgrounds can be found in DFI’s Manual for Non Destructive Testing and Evaluation of Drilled Shafts (2004). Additional information can also be found in the more comprehensive textbook Nondestructive Testing of Deep Foundations by Hertlein and Davis (2006).1.1 PurposeThe intent of this guideline is to provide practical guidance for the proper interpretation of NDT results on ACIP and DD piles. Short descriptions of the main integrity methods available are provided along with several examples of how to use all of the information available to make sound engineering judgments about the results. This publication is a state-of-the-practice guideline to promote accurate engineering evaluations.For engineers inexperienced with NDT, these guidelines provide sufficient background information on NDT methods to help understand the limitations of the testing, assess the results presented to them, and formulate appropriate questions. This is particularly important for engineers charged with the responsibility to determine from those results what, if any, consequences there may be on the performance of the structure under construction."

Jan 1, 2016

By R. Bruce Ferguson

"IntroductionThe Beaverlodge Operation of Eldorado Nuclear Limited is a uranium property located near the north shore of Lake Athabasca about 7 miles from Uranium City, Saskatchewan.The mill is a 2000 tpd carbonate leach operation producing a high grade yellowcake concentrate.The Lamella Thickener was purchased to replace a 55 foot conventional unit which had deteriorated beyond repair. The cost of the unit was considerably lower than for a conventional unit, installation was much simpler and the unit is much more compact allowing it to be installed in the mill basement and be insulated completely.The unit was sized according to the results of tests performed both by the supplier and Beaverlodge engineering staff. The supplier guaranteed overflow clarities of less than 100 ppm suspended solids. The Lamella thickener was developed by A. Johnson Co. of Stockholm, Sweden, is manufactured under license by Parkson Corporation of Ft. Lauderdale, Florida and is distributed in Canada by A. Johnson Co. of Montreal."

Jan 1, 1975

By J. David Chapman

There are a variety of choices of materials for mineral extraction processing. Traditionally, end users have used metallic piping for fluid handling and little is known about the advantages (or limitations) of non-metallic piping systems. This presentation will review custom FRP pipe systems and their use in severe corrosive and erosive process streams. These systems can be designed to various pressure and temperature ratings and different components (such as resin and glass type) can be varied to suit the process conditions

By Michael G. Rulff, Tracy M. Holmes

"Vast amounts of time and money are spent fighting flow problems in plants that involve the handling or processing of industrial minerals. Because these types of projects tend to be capitalintensive, the right decisions, made at the design stage, can have a substantial positive effect on the economics of the project.Some of the problems related to solids flow in mineral processing plants include:•,Flow stoppages•,Uncontrolled flow•,Segregation of blended materials•,Build-up and dead material resulting in loss of live capacityUnfortunately few Universities in North America provide courses in the design or selection of bulk solids handling equipment, let alone the theory of bulk solids flow, with the result that engineers do not fully appreciate the effects of bulk solids handling on their process. The usual method of selecting “standard” equipment, all too often, leaves plant operators hammering on hoppers to promote flow, a technique that is not only usually ineffective but also unsafe and often causes damage to equipment. In short, too little consideration is given, at the design stage of projects, to the particular material and operating environment involved and how these will affect handling between process steps.This paper seeks to give a general understanding of bulk solids flow theory including flow patterns and flow property tests, and presents functional design guidelines to ensure reliable flow. As well, a case history will be presented. Our message is clear: To ensure uniform, reliable flow, a plant design must take into account the specific flow characteristics of the bulk solid to be handled or processed."

Jan 1, 2008

By Nobuaki Sato

For the recovery of uranium from spent nuclear fuel, sulfide reprocessing process, which consists of voloxidation, selective sulfurization, and magnetic separation or selective dissolution steps, are proposed. In this paper selective sulfurization of rare-earth oxides in the presence of uranium oxides was studied by thermogravimetry and X-ray diffractometry. In case of the mixture with UO2, the rare earth oxides R2O3 (R=Nd, Eu, etc.) were preferentially sulfurized by CS2 formingoxysulfides and sulfides, while UO2 remained at temperatures lower than 500 °C. When R2O3was mixed with U3O8, first, the reduction of U3O8 to UO2 occurred at low temperatures followed by the sulfurization of R2O3. The separation of rare earth elements from UO2 in suspensionsolution by the use of permanent magnet was examined. The advantage of the proposed process was also discussed by compared with current process.

Jan 1, 2006

By A. McGarr

The shear stress t that can be sustained by the rock mass in the environs of a mining-induced earthquake controls the near-fault peak ground velocity v of that event according to v=0.25(ß/G)t, where ß is the shear wave speed and G is the modulus of rigidity. To estimate t at mining depths, I review the results of four studies involving Witwatersrand tremors that relate to the bulk shear strength. The first and most general analysis uses the common assumptions that the seismogenic crust is pervasively faulted, has hydrostatic pore pressure before mining, and an extensional stress state that is close to failure. Mining operations reduce the pore pressure to zero within the mine and redistribute the stresses such that, in localized regions, the state of stress is again at the point of failure. Laboratory friction experiments can be used to estimate t in the zero-pore-pressure regime. Second, model calculations of states of stress in the vicinity of mining at about 3 km depth indicated the shear stress available to cause faulting near the centre of a distribution of induced earthquakes. Third, laboratory experiments combined with microscopic analyses of fault gouge from the rupture zone of a mining-induced event provided an estimate of the average shear stress acting on the fault to cause this earthquake at a depth of 2 km. Fourth, moment tensors determined for mining-induced earthquakes usually show substantial implosive components, from which it is straightforward to estimate t. These four different analyses yield estimates of t that fall in the range 30to 61 MPa which implies that near-fault particle velocities could be as high as about 1.5 m/s. To the extent that the causative fault ruptures previously intact rock, both t and v, in localized regions, could be several times higher than 61 MPa and 1.5 m/s.

Jan 1, 2002

By Richard K. Sandaas

Start Date: April 4, 1988 Completion Date: Dec. 29, 1989 Contractor: SCI Contractors Past and present transportation centers will come together at International District Station, located at the south entrance to the tunnel next to the turn-of-the-century Union Station train depot. The area will bustle once again with activity as commuters and visitors converge on the modern transit station at the edge of Seattle's International District. Buses coming from south Interstate 5 and Interstate 90 will enter the tunnel through this station. [ ] International District Station is an open-air station, 1,060 feet long and 82 feet wide (about 15,400 cubic yards of concrete were used to build the station). A concrete lid over the southern portion of the station staging area is held in place by 131 support piles. The station will include entrances on Jackson Street and King Street. Union Pacific Realty is planning to build an office and retail complex upon the lid. The station also has an international flair. Symbols of the Chinese zodiac will be etched into the station plaza floor. The station platform walls will be lined with large steel panels embellished with designs in origami?a Japanese folded paper art form. [ ]

Jan 1, 1990

By Dwayne C. Kicker

This paper introduces the concept of design theory and methodology as applied to rock mechanics for more innovative and efficient design. This is a "frontier" research area in rock mechanics because although design is a fundamental foundation to all engineering branches, very little attention has been paid to this aspect in mining. In discussing the theoretical premise of design, this paper identifies the principles which form the basis of design activity. Also, from a practical viewpoint, the findings from a series of interviews with mine design engineers are presented. These findings lead to the identification of needs arising from overlooked design methodology in practice.

Jan 1, 1989

By John B. Tieder

Arbitration is a legally recognized alternate litigation for the resolution of civil disputes. The parties agree, either before or after a dispute arises, to submit that dispute to an independent third party for resolution. The decision of that third party is binding on the parties. A decision of an arbitral tribunal, typically referred to as an "award," cannot be reviewed by a court except on very limited grounds, such as fraud. See, e.g., Va. Code 8.01-581.010. Indeed, an arbitral award is typically less subject to judicial review than the decision of a trial court, whose decisions are almost always subject to appellate review as a matter of right. Arbitration is typically the result of a contractual agreement between the parties to submit disputes to arbitration. On occasion, arbitration can be required by statute. For example, the California Department of Transportation requires the arbitration of all disputes arising under its contracts. Public Contract Code, Article 7.1 (§§10240-10240.13). There may be a question whether statutorily required arbitration is truly arbitration or an administrative law disputes resolution procedure. The significance of the difference is that the decisions of administrative law bodies are typically reviewable by a court of law as a matter of right while, as set forth above, arbitral awards are almost never reviewable.

Jan 1, 1988

By J. Allan Tice

In the past fifteen to twenty years, the use of drilled piers to support high capacities in coastal plain deposits has become more and more common. With improved construction techniques and better understanding of pier behavior, drilled shafts with capacities of 200 to 500 tons are not unusual. The purpose of this presentation is to review several drilled pier installations from North Carolina to north-east Florida as a means of illustrating the different types of design concepts and installation techniques which are presently being used. ACKNOWLEDGEMENTS The information in this presentation was obtained from work performed by many individuals and companies. The section on limestone socket caissons in South Carolina is an abridged version of a paper prepared by Rob Smith and Neil Gilbert of Law Engineering's Charlotte, North Carolina office, and is used with permission. The section on pier installation in northeast Florida is an abridged version of a paper prepared by Kirk Mcintosh, Tom McDaniel, and Randy Knott of Law Engineering's Jacksonville, Florida office, reprinted here with permission. Additional data discussed in this presentation has been obtained from Farr Foundation Company, McKinney Drilling Company, and Peterson Drilling Company.

Jan 1, 1988

By D. Grabowski, Z. Pokryszka

ABSTRACT: Some residential areas of the iron basin of Lorraine (in the North-East of France) are affected by noxious gas emissions (under oxygenated, carbon dioxide loaded and radon loaded gas mixtures). Site investigations showed that the gas flow was mainly due to natural thermal air circulation between old mines and the external atmosphere. The main hazards associated with this flow of gas and its potential accumulation in confined volumes within buildings are asphyxiation and intoxication. A further study is in progress in order to better understand the origin of the gas generation within the old iron mine workings. Following the first hypothesis, the carbon dioxide emission is mainly due to the specific hydro-geo-chemical process associating the pyrite oxidation with the acid dissolution of carbonates. KEY-WORDS : gas, emission, mine, flow, pyrite. ZUSAMMENFASSUNG: Einige Wohngebiete der Eisenmulde Lothringen (im Nordöst Frankreich) werden von Ausgasung gesundsheitsschädlichen sauerstoffarmen Mischungen, die mit Kohlendioxid und Radon beladen sind, betroffen. Untersuchungen am Ort haben gezeigt, wie diese Gasstroemung von natürlichem thermischen Luftumlauf zwischen den alten Bergwerken und der externen Atmosphäre ausgelöst wird. Erstickung und Vergiftung sind die wichtigste Risiken, die mit dieser Gasströmung und ihrer möglichen Speicherung in begrenzten Lokalen zusammenhängen. Eine weitere Untersuchung wird durchgefuehrt so dass man die Herkunft der Gaserzeugung in den alten Grubenräume besser versteht. Der ersten Hypothese folgend, Ausgasung von Kohlensäure liegt vor allem an dem hydro-geo-chemischen Prozess, der Pyritrösten mit der säuren Auflösung von Karbonate verbindet SCHLÜSSELWÖRTER: Gas, Ausgasung, Bergwerk, Strömung, Pyrit RESUME: Certaines agglomérations du bassin ferrifère lorrain (au Nord-Est de la France) sont affectées par des émanations de mélanges gazeux sous-oxygénés et chargés en certains gaz nocifs (dioxyde de carbone, radon…). Les investigations effectuées in situ ont montré que les écoulements gazeux à l’origine de ces émanations sont liées au phénomène de tirage naturel entre les anciens travaux miniers et la surface. Les principaux risques engendrés par ces émanations de gaz et son accumulation possible dans des endroits confinés sont l’asphyxie et l’intoxication. Une étude est en cours afin d’expliquer l’origine de la modification de l’air au sein des vieux travaux miniers. Les émissions de dioxyde de carbone seraient dues à des processus hydro-geo-chimiques associant l’oxydation de la pyrite et la dissolution de carbonates. MOTS CLES: gaz, émanation, mine, écoulement, pyrite.

Jan 1, 2003

By B Olsson, B Reynolds, R Norman

An unprecedented growth in demand for coal exports has placed pressure on multi-user coal chains to guarantee that their capacity expansion projects will meet the required demand. These projects, however, are taking place in an increasingly complex commercial and technical environment - competing rail and coal terminal service providers as well as a myriad of competing mine operators, all needing to operate in an increasingly integrated manner to get the most out of expensive shared assets.Increasing system complexity and integration has driven the need for more holistic and sophisticated analysis tools. The capacity of coal chain subsystems, such as mine, rail and port, can no longer be determined effectively in isolation. Understanding the nature of the interactions between these subsystems, their sensitivity to uncertainty and the resultant capacity of the integrated system is the key to both maximising value and minimising risk.Recently, TSG has worked closely together with the Integrated Logistics Company and a number of key stakeholders in the Dalrymple Bay Coal Chain to develop independent system master plans. These master plans have provided a quantitative and rational assessment of coal chain capacity in its current state and a prediction of its capacity once a pipeline of committed capacity improvements is in place. This paper provides an overview of the study and a comprehensive guide to the process required to effectively achieve valuable strategic insights in a challenging multi-user stakeholder environment.CITATION:Reynolds, B, Olsson, B and Norman, R, 2012. Using independent system simulation to mitigate risk in the Dalrymple Bay Coal Chain, in Proceedings Project Evaluation 2012 , pp 77-84 (The Australasian Institute of Mining and Metallurgy: Melbourne).

May 24, 2012

By Jilai Xue

Fe-Ni alloys can be used as raw material in making stainless steel. Laterite nickel ore is one of mineral resources for producing nickel alloys. In this work, the laterite ore after dehydration at 800 °C and the anthracite as reducing agent were mixed for pre-reduction at 900 °C, and then reduced to form Fe-Ni alloys at 1550-1620 °C through carbon-thermal reduction process. A high Ni-content alloy component in the metallurgical mixture can be formed through pre-reduction. Better separation of the resulting metals from the slag is found with lower Ni-content alloys produced or higher temperatures during reduction. An effective processing of Fe-Ni alloys needs further understanding of the process fundamentals and optimizing of the process parameters.

Jan 1, 2010

By Paul Krivokuca

Outline Quinsam Coal Mine ?? Location ?? Mine History ?? Safety ?? Production ?? Hiring 4S Mine ?? Depillaring design ?? Structural mapping, Risk assessment ?? Rock Bolt Design Selection ?? Training

May 1, 2008

By T. E. Wakefield

Over several decades in Southern Africa the advance rates when sinking vertical shafts have declined significantly. The upside has been a substantial improvement in shaft bottom conditions and a commensurately improved safety performance, with an increasing number of shafts being sunk without fatalities and disabling injuries. This paper briefly reviews historical sinking rates and matches changed sinking productivity to the introduction of new sinking methods that have been adopted to eliminate/mitigate safety risks. Meeting the challenge of returning to historical advance rates whilst progressing in the quest for zero harm by utilizing three dimensional animated computer modelling is described. Making use of commercial modelling software makes it easier to evaluate different methods, sequencing, in shaft barrel ergonomics, and stage and shaft bottom layouts before procuring project plant and equipment. Benefits accrue not only in better communicating methods and configurations for detailed planning and design, but also during crew training. The traditional engineering ?as-built? drawing practice has been extended to the concept of an ?as executed? sinking model which seeks to capture operational experience and learning for future best practice. The paper concludes with some of the organizational culture challenges being overcome as this non traditional approach to shaft sinking optimization is being introduced.

Jan 1, 2009