Search Documents

By C. Sunderman, G. Feagan, C. Stazick

Galvanic corrosion between dissimilar materials, such as steel and graphite, leads to safety concerns for many industries, including mining. In this study, researchers from the National Institute for Occupational Safety and Health (NIOSH) analyzed rock samples from two mines in the United States that exhibit electrochemical properties similar to graphite through laboratory measurements to investigate their observed in-situ influence on underground metal support. Uniform corrosion rates of mild steel coupons, inflatable bolt coupons, and friction bolt coupons galvanically coupled to rock samples were obtained using both potentiodynamic polarization and zero resistance ammetry. Increased uniform corrosion rates were witnessed between the coupled rock and steel system, over those of just the steel alone. Surface analysis of the metal samples showed the presence of pitting corrosion, reflective of bolt samples removed from partner mines. Corrosion pitting of ground support structures in contact with graphitic rock in underground mines poses safety concerns for mine workers by increasing the rate of corrosion and decreasing bolt strength over time and will be further investigated for intervention strategies.

Feb 1, 2023

By Francis Welington Moraes da Cruz

O sistema de despoeiramento primário da Aciaria da thyssenkrupp CSA é um equipamento complexo utilizado durante o sopro no conversor para captação, limpeza e resfriamento dos gases. Estes gases são indiretamente resfriados em uma caldeira de recuperação de calor quase vertical de grande altura. Em seguida passa por resfriamento direto (resfriador evaporativo) com injeção de água e vapor, onde há uma decantação das partículas maiores. Em seguida os gases penetram no precipitador eletrostático, onde é retirada quase a totalidade do pó restante. Um ventilador de grande potência faz a exaustão destes gases, através da caldeira, resfriador evaporativo e precipitador eletrostático, para em seguida comprimi-los para a chaminé ou para o último resfriamento dos gases antes do envio para o gasômetro. A chaminé possui um queimador piloto que queima o monóxido de carbono (CO) transformando-o em dióxido de carbono (CO2). Do gasômetro, os gases podem ser fornecidos para outras unidades da usina onde é consumido como combustível. O objetivo deste trabalho foi aumentar a energia do gás BOF (Basic Oxygen Furnace), através de um conjunto de ações, visando à redução de emissão de gás CO2, redução de consumos de gás natural e aumento da geração de energia.

Jan 16, 2018

By U König

The use of high speed detectors made X-ray diffraction (XRD) an important tool for quality and process control in the mining industries. Besides knowledge about the mineralogy of a sample it provides useful information in terms of quantification of the crystalline phases and the amorphous content. Cluster analysis of XRD data can facilitate multi-dimensional mapping of ore deposits and drill cores, identifying regions of favourable mineral compositions. The studies of this paper demonstrate how XRD and data clustering can be used for grade control, process optimisation and quality control of iron ores and iron ore sinters. These new developments have an enormous potential as an inexpensive, reliable tool, useful in the characterisation of iron and sinter materials implemented in an industrial environment.

Jul 11, 2011

By A. T. Tye

This paper describing the concentrator practice of the Cananea Consolidated Copper Co. at Cananea, Sonora, Mexico, is one of a series of articles on milling methods and costs being prepared by the U. S. Bureau of Mines. The Cananea concentrator treats 2,400 tons of copper ore per day by preferential flotation, whereby the copper sulphides are floated and the iron pyrite depressed. During the first half of the year 1929 the heads to the concentrator averaged 3.29 per cent of copper, the recovery was 95.74 per cent of the total copper, and the concentrates produced contained 21.44 per cent of copper.

Jan 1, 1930

By Lloyd H. Banning

ELECTRIC smelting tests were conducted at the Northwest Electro-development Experiment Station, Albany, Oreg., to develop a feasible process for producing silicomanganese from siliceous manganiferous material. The Jackson County, Oreg., material used was massive and contained rhodonite as the most abundant mineral. Both raw and beneficiated materials were tested; various proportions and types of fluxes and reductants were used to make up the furnace charges. The silicomanganese product was used successfully in manufacturing various steels at industrial plants. The manganese content of the samples ranged from 23 to 28 percent; silica plus alumina content was as high as 55 percent-about four times the maximum specification for Metallurgical-grade ore. Sink-float laboratory tests indicated that the manganiferous material was amenable to beneficiation. Over 2 tons of rhodonite concentrate was prepared for smelting tests in a sink-float operation. Only the minus-3/4-inch, plus-8-mesh fraction was fed to a heavy-medium cone; over 97 percent of the manganese was recovered in the sink product, which contained 32.4 percent manganese and 44 percent silica plus alumina. About 25 percent of the silica was removed in the float product.

Jan 1, 1959

By G. F. Liu, S. Owada

Platinum Group Metals (PGMs), Pt, Pd, Rh, have been widely used as a three-way catalyst to clean discharged gas from automobiles and therefore a considerable amount of the spent catalysts is generated annually. This paper proposes a novel concentration technology of PGMs by utilizing the double-deck structure of PGM bearing alumina-ceria and cordierite phases. The applied technologies are a combination of heating-quenching, selective grinding and screening for separating alumina-ceria phase from cordierite. Temperature change as a function of quenching time and the thermal stresses applied to both phases were simulated and calculated by FEM, and it was clarified the mechanism of micro-cracks generation at the phase boundary and micro-cracks in alumina-ceria phase, which indicated that separation of alumina-ceria phase from cordierite and selective breakage of alumina-ceria phase could be achieved in the subsequent selective grinding with an attritor. This process could concentrate 46 wt% of alumina-ceria phase into fine fractions with 86 % recovery efficiency. The remaining alumina-ceria phase can be further recovered by applying flotation and so on.

Jan 1, 2015

By Rosa Malena Fernandes Lima, Kerollan da Silva Ramos, Joyce de Assis Silva, Geriane Macedo Rocha

This study evaluated the effects of collector type amide-amine compared with those of conventional etheramine acetate (both cationic collectors) on the surface properties of quartz and hematite. An examination of certain properties of the reagents indicated that the new collector amide-amine has CMC (critical micelle concentration) and pKa values (100 mg/L and 8.2, respectively) significantly lower than those of etheramine (800 mg/L and 9.4, respectively). Microflotation tests showed that the recoveries of quartz with amide-amine in all the concentrations tested were higher than those with etheramine. This is attributed to its lower CMC and pKa values. The selectivity window between quartz and hematite flotation using amideamine was higher at pH 10.5 (approximately 80% for 5 mg/L). Therefore, the use of starch is not necessary in siliceous itabirite flotation by amide–amine collector. Zeta potential measurements and infrared spectra reveal that the adsorption of amide-amine collector on quartz surface occurs mainly by electrostatic attraction. Considering the better collectability of amide-amine for quartz flotation and lower adsorption affinity for hematite surface than etheramine, the amide-amine is a promising collector to be used in reversal iron ore flotation.

Jul 30, 2021

By Muhammed Şener, Ahmet Gültek

The flotation chemicals are important in mineral processing, and new progress is made in this area day by day. For sanidine purification, some commercial collectors, which can be harmful to the environment, are used. In that respect, the poly(amidoamine) (PAMAM) dendrimers, which are non-toxic for the environment, are good candidates for flotation applications. In this study, the second-generation PAMAM dendrimer was used as a collector to remove magnetite from sanidine by microflotation method, and obtained results were compared with commercial collectors. The results showed that the PAMAM dendrimer is an efficient and selective collector for magnetite. PAMAM adsorption mechanism was determined by zeta potential and FTIR spectra. According to the microflotation results, 87.76% of magnetite recovered at pH 8 by using PAMAM as a collector. It was found that the flotation recovery with the PAMAM dendrimers is similar to the Aero 704 between pH 2 and 6 but less between pH 6 and 9 and more between pH 9 and 12. All experiments were carried out five times and the standard deviation of all results was evaluated with p = 0.05 confidence interval. The second-generation PAMAM dendrimers can be an alternative flotation chemical to the commercial ones concerning usability at a wide pH range, recovery potential, and environmentally benign.

Apr 28, 2023

By A. R. Miller

A fuel cell locomotive incorporates the advantages of its competitors, namely catenary-electric and diesel-electric units, while avoiding their disadvantages. It possesses the environmental benefits, at the vehicle, of an electric locomotive but the higher overall energy efficiency and lower infrastructure costs of a diesel locomotive. The natural fuel for a fuel cell is hydrogen, which can be produced from many renewable sources or via nuclear energy, and thus a hydrogen-fuel cell locomotive will not depend on imported oil. Hydrogen produced from renewable primary energies or nuclear energy would provide a totally zero-emissions vehicle, that is, with zero carbon in the energy cycle. A project partnership among Vehicle Projects Inc of the USA, and South African partners Anglo American Platinum, Ltd, Trident South Africa, and Battery Electric, has designed and is launching a series of five prototype fuel cell-powered mine locomotives.

Jan 1, 2012

By J. T. Dunham

The Bureau of Mines studied by dilatometry the effect of titanium on the thermal expansivity of hot-rolled zinc and Zn-l percent Cu alloy. The titanium content of the alloys was varied up to 0.3 percent. Expansion coefficients were determined from measurements made both parallel and perpendicular to the plane of the rolled sheet. Titanium reduced expansion parallel to the plane of the sheet, especially in the rolling direction, but increased expansion perpendicular to the sheet. Basal-plane pole figures showed that the degree of preferred orientation increased with the titanium content in the alloy, and that anisotropic expansion can be correlated to sheet texture.

Jan 1, 1965

By E. W. Dean

This report on the physical and chemical properties of typical crude oils of Oklahoma is the sixth in a series of preliminary chapters of a bulletin covering the producing districts of the United. States. Preceding reports* may be obtained on request. The details of the methods used in this survey in collecting samples, making laboratory tests, and interpreting results are discussed in the first three papers. If any errors or omissions are noted by readers, it is hoped they will be brought to the attention of the Bureau of Mines for correction before the appearance of the permanent report. Samples of Oklahoma crudes analyzed in this report were taken from those fields representing the major production of the State. The Oklahoma Geological Survey designates 172 different oil and gas fields in the State, S1 being in Osage County, 14 in Tulsa County, 14 in Okmulgee County, 9 in Washington County. The list of samples collected by the Bureau of Mines represents only 5 fields in Osage County - Bigheart, Burbank, Hominy, Osage Junction, and Pershing - yet these samples, together with those from adjoining fields, are representative of nearly all crude produced in the county. The sample 'from the Pershing field, for example, is representative of the crude produced in several fields in that part of the county - such as Nelagoney, Pawhuska, Wyomona - and the sample from the Skiatook,

Jan 1, 1922

By T. Kerr, C. Mattich, J. Wilson

"In refractory gold concentrates, gold is occluded in sulphide minerals preventing efficient cyanide leaching. Hence, roasting is used to oxidize sulphur and organic carbon, the latter being necessary to minimize recovery loss through the preg-robbing effect. In 2009, Outotec commissioned the circulating fluidized bed roaster at Syama gold mine in Mali. Since 2013 Resolute and Outotec have been implementing improvements to the roaster performance with the capacity increasing from 8000 t/month in 2013 to above 13,000 t/month in 2016, while achieving a residual sulphide sulphur and organic carbon contents of below 0.1 wt.% and 0.4 wt.%, respectively. Thus a gold recovery in the CIL of above 90% is attained. In 2016, Outotec audited the Syama roaster. The analysis resulted in the Low Carbon Roaster (LCR) upgrade concept which (i) allows re-processing of calcine dust from the spray cooler and ESP after pelletization and (ii) allows the roasting of a further fine-organic carbon rich feed, i.e. de-slime circuit tailings. The LCR upgrade aims to reduce organic carbon to <0.2 wt.% and increase roaster-leaching gold recovery by >3%. Project development included extensive testwork. The LCR process is expected to become operational during FY 2019.INTRODUCTION Double refractory sulphide ores exhibit the characteristics of gold locked within pyrite grains, in the presence of preg-robbing natural (organic) carbon. Hence, to achieve high recovery during subsequent processing steps, i.e. cyanide leaching, oxidation of sulphide sulphur is required, producing a porous calcine by way of a roasting step. This allows for the gold contained within the pyrite grains to be accessible during cyanide leaching. Furthermore, it is necessary to oxidize the organic carbon. Oxidizing the organic carbon is essential as gold recovery loss occurs as a result of gold-cyanide complexes being adsorbed on organic carbon, this phenomenon is termed as preg-robbing (Miller et al., 2016). The gold absorbed on the organic carbon is lost, reporting to the tailings stream. Hence, the aforementioned oxidation of sulphide sulphur and organic carbon is the process goal. Nonetheless, the latter must occur at a controlled temperature which is concentrate/ ore specific, since the pores of the produced calcine should not sinter, as this makes the gold contained in the calcine less accessible during leaching, leading to gold recovery loss. The tight temperature control requirement is a decisive factor in the choice of a Circulating Fluidized Bed (CFB) as the roasting reactor, due to the excellent mixing characteristics of the CFB which results in temperature homogeneity of (+/-10°C). Roasting of double refractory ores, as described above, can be included in the flowsheet after comminution and grinding, a process termed as whole ore roasting, or by including a flotation circuit termed as concentrate roasting. Roasting the flotation concentrate results in less solid flow, increased sulphide sulphur grade and organic carbon content resulting in a higher heating value and higher gold content. A typical composition of the Syama ore and concentrate is given in Table 1. Ore average values presented correspond to the period 2015, while concentrate values are typical for the flotation performance throughout the period 2012–2015."

Jan 1, 2017

By R. Gilges

The implementation of effective techniques for meeting the maintenance requirements of the new Utah Copper Division smelter, one of the largest in the Western Hemisphere, is a goal of the smelter management and supervisory personnel. Kennecott&apos;s Metal Mining Division Computing Center has been working with smelter personnel to implement a computer program to provide instantaneous access to equipment specifications, maintenance and cost histories, spare parts, preventive maintenance scheddes, etc. for several hundred pieces of equipment. This information will be available to all smelter personnel via visual display terminals. The system will dramatically reduce the time now spent in search of pertinent information required in effectively performing the maintenance functions. It will also be used to analyze practices, detect trends, prepare budgets, and substantially reduce the paper work normally associated with the running of a large and complex maintenance organization.

Jan 1, 1977

By F. Baczek, S. S. Rocks, D. Chaiko, T. Walters

The atmospheric leaching of chalcopyrite concentrates using acidic ferric sulfate lixiviants is well known to suffer from slow leach kinetics and poor copper recoveries. A number of approaches have been proposed for improving both leach kinetics and recoveries in this system. Many of these, while effective, suffer from high CAPEX and/or OPEX. As many mine sites begin transitioning from heap leaching of copper oxides to processing of primary copper sulfides, cost-efficient leach processes that are compatible with existing SX/EW processes will be needed to maintain existing cathode production. To this end, FLSmidth is exploring process options and reactor technology for the hydrometallurgical processing of primary sulfides. One approach that appears to be highly effective at increasing copper recoveries takes advantage of the enhanced reactivity of transitory, surface-defect structures generated during particle fracture. Significant process efficiencies are gained by matching the rate of grinding to the rate of electrochemical leaching in Mechano-Chemical leach processes. The patent-pending FLSmidth® ROL process uses a Stirred Media Reactor (SMRt reactor) to achieve copper recoveries of 97+% in 6 hours or less. This approach overcomes many of the surface passivation problems that have hindered other atmospheric leach processes. New insights to leach mechanisms are presented.

Jan 1, 2015

By S. C. Termes

To help develop the basis for new fine-particle separation methods, the Bureau of Mines has investigated the use of cross-linked starches containing four chelating groups--carboxylate, iminodiacetate, dietha-nolamine, and xanthate--as flocculants for selected metal oxide and hydroxide mineral fines. It was found that those starches capable of interacting with the mineral surface by a chemisorpti,on mechanism (as indicated by zeta potential measurements) produced the highest recover-ies and&apos;grades of the metal oxide or hydroxide when flocculated from a binary mixture with quartz. The effects of pH, dispersing agent, stirring rate, stirring time, and starch dosage on selective flocculation were studied for binary mixtures of hematite and chromite with quartz. Floc strength becomes important in achieving maximum recoveries by mechanical postflocculation separations.

Jan 1, 1985

By G. Deschenes

"This literature survey discusses the recovery of gold from thiourea solutions. An overview of techniques used and general comments on the basic cyanidation methods are presented. The chemistry and mechanisms of cementation, activated carbon, resins, electrowinning, solvent extraction and pressure reduction are examined. Conclusions and recommendations give orientation for future research and development activities in this field.RésuméCette revue littéraire traite de la récupération de I ‘or des solutions de thiourée. Elle fait un survol de I ‘ensemble des techniques utilisées tout en introduisant des commentaires généraux sur la méthode classique qu&apos;est la cyanuration. La cémentation, Ie charbon active, les résines, l&apos;électroextraction, I ‘extraction par solvant et la réduction sous pression sont les méthodes analysées tout en considérant leur caractère chimique respectif ainsi que les mécanismes qui y sont rattaches. Des conclusions sont tirées et différentes recommandations sont suggérées pour orienter la recherche dans ce domaine."

Jan 1, 1986

By Sean Gallagher

The restricted workspace present in low-seam coal mines forces workers to adopt awkward working postures (kneeling and stooping), which place high physical demands on the knee and lower back. Method: This article provides an analysis of injury claims for eight mining companies operating low-seam coal mines during calendar years 1996-2008. All cost data were normalized using data on the cost of medical care (MPI) as provided by the U.S. Bureau of Labor Statistics. Results: Results of the analysis indicate that the knee was the body part that led in terms of claim cost ($4.2 million), followed by injuries to the lower back ($2.7 million). While the average cost per injury for these body parts was $13,100 and $14,400, respectively (close to the average cost of an injury overall), the high frequency of these injuries resulted in their pre¬eminence in terms of cost. Analysis of data from individual mining companies suggest that knee and lower back injuries were a consistent problem across companies, as these injuries were each among the top five most costly part of body for seven out of eight companies studied. Application/Impact: Results of this investigation suggest that efforts to reduce the frequency of knee and low back injuries in low-seam mines have the potential to create substantial cost savings.

Jan 1, 2009

By H. L. Gilbert

Zircon sand may be reacted with sodium hydroxide at 600° C. to form sodium zirconate and sodium silicate. Sodium zirconate is water insoluble and so may be washed free of sodium silicate. The sodium zirconate may then be converted to zirconyl chloride by the action of hydrochloric acid and the zirconyl chloride crystals separated by cooling the solution. This approach produces zirconyl chloride of satisfactory purity with less cost than is involved in buying anhydrous zirconium chloride and converting it. A proposed design for a plant is given, INTRODUCTION This work was conducted by the Rare Metals Branch as a part of research on zirconium at the Bureau of Mines Northwest Electrodevelopment Laboratories, Albany, Oreg., under the guidance of S. M. Shelton, Regional Director. The work was supervised by W. W. Stephens, head of the Rare Metals Branch (now with Carborundum Metals Corp.).

Jan 1, 1954

By Tim Arnold

"Justified is a show on FX that takes place in Kentucky coal country. The two main characters, a cop named Raylan and a criminal named Boyd, are adversarial to the very end, yet they manage to maintain a seemingly inexplicable bond of friendship through it all. The final episode ends (spoiler alert) with Boyd asking Raylan why that is. He responds, “If I allow myself to be sentimental, there is one thing I wander back to” Boyd responds, “We dug coal together.” Fade to black.What creates these types of bonds between friends and co-workers in mining? I don’t know about you, but many of my best friends I met in mining. Certainly the people I respect the most in this world are a part of our industry. Good, honest, honorable men and women. And I am not just talking about the leaders of our industry. I am talking about great miners who taught me how to do the right thing and also be productive.I have had the pleasure to work for some great people and the misfortune of working for some of the loudest screamers. What I consider the worst butt-chewing in my life may surprise you. I once worked for a man I respected, because he showed me respect. He went on a business trip and left some instructions. For some reason, I was able to justify to myself that they applied to everybody but me, and I disobeyed them. When he returned he called me into his office and said to me: “Tim, you pissed me off when you did that.” He said it quietly and with no anger. I had lost his respect. This devastated me more than any screaming shift boss ever could have. I learned a lot about values from that conversation.Most of us will spend more time at work than we will with our families over a lifetime. It is natural that tight bonds be created at work. What I believe makes mining special is that these bonds are so strong. They are strengthened by the incredibly hard work our miners do. They work at all hours, on holidays and in all sorts of extreme weather conditions. The physical demands of the job are sometimes exhausting. Our bonds are further reinforced because the work is dangerous. Not only does management watch out for the wellbeing of their people, but each and every one of us looks out for one another. The bonds are made tight because our people are so passionate about what they do, no matter the department or profession. Finally, they are strong because of the thousands in the industry that keep doing the right thing, every day. We make great friends in this industry because of the strength of character of our people. That is why Boyd and Raylan respected one another so much."

Sep 1, 2016

By Daniel G. DiCanio

Investigation of the costs of industrial accidents dates back to the 1920s. The Bureau of Mines was one of the pioneers in accident cost investigation with numerous studies published between 1928 and 1933. The bulk of these early investigations dealt only with costs which appeared as payouts on company books; that is, the direct cost of insurance premiums and the costs of medical expenses which resulted from industrial accidents. These early investigations, especially the Bureau&apos;s study of accident costs in Pennsylvania and Indiana coal mines provided the first real evidence that promotion of industrial safety pays back in dollars as well as in human life and wellbeing. In the 30s and 40s, investigations began to accumulate evidence that industrial accidents impacted more than just the direct operating expenses of a company (i.e., higher insurance premiums). The work of Heinrich pioneered these investigations, and produced strong evidence that the un¬insured costs of accidents far outweighed those costs covered by insurance. Heinrich developed and published a ratio of insured to uninsured costs of 1.4. Despite his cautionary statements about blanket application of this ratio it is used even today to estimate total costs of accidents. Simonds, in the late 40s and early 50s, extended the definitions of uninsured or indirect accident costs and developed what is now regarded as the principal method for estimating the total economic impact of industrial accidents. Simonds&apos; method served as the basis for development of the logic of the Accident Cost Indicator Model (ACIM). However, several departures from Simonds&apos; method were made to satisfy certain requirements imposed by the Bureau of Mines, and because information gathered during the course of our investigation justified a departure. These departures are noted in the discussion which follows.

Jan 1, 1977