Search Documents

By Artur Augusto Martins

Este trabalho tem como objetivo apresentar o projeto de uma plataforma de cloud computing onde profissionais de diversos segmentos da metrologia, calibração, instrumentação e controle poderão cooperar entre si no desenvolvimento de metodologias de medição, análise numérica e automação. A plataforma permite o modelamento matemático e o estudo analítico e/ou numérico de processos utilizando recursos disponíveis de cloud computing e a apresentação dos resultados e geração de relatórios através de uma interface web. Através do desenvolvimento cooperativo de novos procedimentos para análise de dados, modelos de instrumentos e melhorias operacionais do sistema pretende-se que o mesmo aproxime-se cada vez mais de um LIMS totalmente funcional e que tenha maior aderência à norma ISO/IEC 17025.

Jul 30, 2018

By E Macmillan

For any processing plant there will be deleterious elements or minerals which affect production or quality, and a strategy to predict their occurrence and mitigate their impact is required. An early objective of the Olympic Dam geometallurgy program was prediction of the acid consumption and gelling behaviour of the ore, which affects leach recovery, throughput and circuit availability. The geometallurgical test program measured the response of a wide range of ore types, and then relationships between mineralogy, metallurgy and chemistry were developed. Thus the drivers of acid consumption and triggers for gelling events could be described in ways that were meaningful to plant operations.To enable optimisation of the mine planning and ore blending processes, the parameters driving metallurgical response must be translated to the block model. Data support is critical in populating a block model. Assay information is easily obtained, but mineralogical and metallurgical information is more expensive and time consuming to collect. Hence population of a block model with mineralogical and metallurgical values using a conventional geostatistical approach is not always possible.An alternative approach employed at Olympic Dam was the development of a suite of assay-to-mineral algorithms. These algorithms were calibrated using all available mineralogical information, and this enabled the calculation of mineral abundances for more than 1.5 million assayed samples. Estimation of the minerals in the block model, and the generation of acid consumption values for each block could subsequently occur.The use of back-calculated mineralogy from assays as part of process model generation is an innovative tool which can be used for mine planning and optimisation and to ensure the plant does not receive any unwelcome surprises. Ultimately, one purpose of geometallurgy is to predict potential processing issues and their drivers so that these can be mitigated. A strategy to achieve this is outlined hereafter.

Sep 5, 2011

By B Armstrong

The Proterozoic poly-metallic Trilogy deposit was discovered in 1997, and until recently, mining evaluation was stalled due to poor metallurgical performance. Unlocking the substantial economic value of the deposit required a coming together of geologists, mineralogists, metallurgists and mining engineers, who by working collaboratively, uncovered the detail necessary to allow the required metallurgical breakthroughs to occur. The deposit itself is described as a sedimentary exhalative (SEDEX), with an enriched lead-zinc-silver core surrounded by a broader envelope of copper-gold mineralisation. The geological domains were defined in broad terms based on the style of mineralisation, assay values and lithology. These domains, while adequate for the resource estimation process, failed to translate into representative metallurgical domains. Additional work with new techniques defined regions in the deposit with altered processing properties which could not be recognised by conventional geological logging. Such additional complexities could not be appreciated at the outset of the metallurgical test work program.These regions were defined by applying the EDTA analysis method for recognition of where the valuable sulfides, particularly galena, had been partially modified by oxidising conditions. Hence, the flotation response of the valuable sulfide minerals was diminished and the increased amount of heavy metal cations available in the system significantly reduced selectivity in the flotation process.Understanding the detail of this complexity was essential in determining representative metallurgical domains, which was the first step in the long road of development.

Sep 5, 2011

By Donald H. McLaughlin

ALTHOUGH Cerro de Pasco was well known since the early sixteen hundreds as one of the major silver districts of the Andes, its development on a modern scale did not occur until the first decade of the present century when a syndicate organized by James B. Haggin initiated the enterprise that eventually grew into the complex and widespread operations of the Cerro de Pasco Copper Corporation. Options on a few claims in Cerro de Pasco that had been brought to New York in 1900 came to the attention of A. W. McCune, a mining man from Salt Lake City, who took them to Haggin and soon succeeded in interesting that creative mining financier in the possibilities of the district. James MacFarlane, an engineer well known to both Haggin and McCune, was sent to Peru early in 1901 to make the initial examinations which promptly led to acquisition of a substantial group of claims in the heart of the mineralized area. A syndicate to which Haggin turned over his rights was organized on Feb. 26, 1902 to provide the necessary funds. The original members were J. B. Haggin, who retained a 34 per cent interest, Edward H. Clark (for Mrs. Phoebe Hearst, the widow of Haggin's old associate, George Hearst), H. McK. Twombly, H. C. Frick, D. O. Mills, and J.P. Morgan.

Jan 1, 1945

By K Smith

This paper presents an assessment of the Robertson (2010a) method within the CPTu inversion parameter framework of Been et al. (1987), using CPTu calibration chamber data presented by Jefferies and Been (2015) and in other literature to assess the validity of the method, with particular focus on applicability of the method to TSFs (i.e. its applicability to loose silts and silty sands). The assessment demonstrates that although the method estimates values of k consistent with calibration chamber data, the method estimates values of m that are generally 1.5 to 2 times greater than calibration chamber data. As a result of this, the method generally overestimates Ψ for values of Ψ less than 0, and underestimates Ψ for values of Ψ greater than 0. This may result in both overly conservative assessment of materials as potentially liquefiable and unconservative predictions of material behaviour for loose materials.

Jul 1, 2021

By W. P. Diamond

The Bureau of Mines has been involved in the drilling of vertical, horizontal, and directional coalbed gas drainage boreholes for mine safety since 1964. In that time, boreholes have been drilled in most of the major coal regions of the United States under a wide variety of geologic conditions. Many of the geologic conditions that occur in the coal measures are detrimental to gas drainage; others may be beneficial. Analytical techniques to determine the gas content of coal samples and evaluate regional trends of gas distribution have been developed. Drilling techniques that maximize the acquisition of coalbed gas data and geologic information have been determined. Although some of the geologic factors influencing the placement and potential success of coalbed gas drainage boreholes have been reported in papers on individual projects, a complete, systematic compilation has not previously been available. The objective of this paper is to pro- vide information on specific geologic factors that should be considered prior to, during, and after the drilling of coalbed gas drainage bore-holes. Many of the commonsense considerations that have been learned through many years of Bureau of Mines experience, but have generally not been reported formally, are included for those who may be considering coalbed gas drainage drilling for the first time, or who have not had the opportunity to encounter a substantial number of geologic situations.

Jan 1, 1982

By Mingyang Li, Yan Lv, Xiaolong Ma, Xudong Gao, Jie Zhao, Yingyi Zhang

The reduction process of pre-oxidized ilmenite concentrate powder in 30%CO–70%N2 atmosphere was characterized by thermogravimetric and differential thermogravimetric (TG-DTG) analysis system at the temperature from 1073 to1223 K. The isothermal reduction results show that the reduction process is divided into three stages and the corresponding apparent activation energies are obtained by iso-conversional method and model-fitting method, respectively. For the first stage, the conversion degree increases sharply with increasing time, and the reduction process is controlled by the random nucleation and subsequent growth model (A2 model). For the second stage, the conversion degree increases slowly with increasing time, and the reduction process is controlled by the diffusion of carbon monoxide in the reduced layer (D1 model). For the third stage, the reduction processes at different temperatures are controlled by the diffusion of carbon monoxide in the reduced layer (1073 K and D1 model), phase boundary chemical reaction (1123 K and R2 model), random nucleation and subsequent growth (1173 to 1223 K, A2, and A3 models), respectively. For the whole reduction process, the apparent activation energies obtained by iso-conversional method and model-fitting method are 71.72 and 31.92 kJ mol−1 , respectively

By Arno C. Fieldner

The determination and publication of data o the chemical and physical properties of American coals have been primary functions of the Bureau of Mines since its creation in 1910. In recent years this program has been expanded to meet increasing needs for information on the suitability of coals for the production of coke, gas, and byproducts, and within the last year an experimental coal-hydrogenation plant has been completed. With this addition, the Bureau is able to cover every phase of coal utilization, including combustion, carbonization, liquefaction, and complete gasification. The need for this information is increasing not only to meet the requirements of consumers but also to give the data required to establish the classification and minimum selling price of coal by the National Bituminous Coal Commission.

Jan 1, 1938

By H. Sevim

An innovative approach in designing the haulage systems for underground coal mines is discussed in this paper. The haulage systems are formed by serially connected components. Therefore an economic and efficient design of the entire system is necessary. The computer model that uses a heuristic algorithm solves this design problem globally in a single run. It is a probabilistic model because it considers the probabilistic aspects of face operations. It is versatile because it can accommodate any type of mining and belt conveyor network configuration. The hoisting section can be used to design drum or friction hoisting systems for single or multiple level operations. These systems can have two skips in balance or a skip and a counterweight in balance. The model also has the option to internally determine the capacity of bunker(s) and shaft-bottom bin. The objective is to minimize the expected cost per ton of coal hauled from the coal faces to the surface. At the end of the paper is an example that illustrated the capabilities of the model.

Jan 1, 1987

By Joseph T. Singewald

The possible value of the red hematite iron ore of the southern Appalachian States, if some practicable method of concentrating it could be devised, has long been recognized. The ore is very low grade, and although in enormous quantities, particularly in the States of Alabama, Tennessee, and Georgia, is only at a few points rich enough to work, and even the best of it ranks among the lowest grade iron ores being mined in the United States. A cheap method of beneficiating this ore would make enormous quantities available and vastly increase the iron-ore resources of the country. However, this low-grade ore in effect constitutes a potential iron reserve, and as long as ample quantities of ore can be obtained elsewhere the question of its utilization does not demand immediate notice. Where these ores are in part of workable grade, however, a problem of more immediate importance arises which, from considerations of economy and prevention of waste in their mining, ought to be solved or, at least, attacked as quickly as possible. Where these ores are being worked they are usually intimately associated with lower-grade material that in mining is left behind. The difficulty and expense of going into ground broken by old workings makes the recovery of this lower-grade ore practically impossible and it is lost forever. Success in concentrating the red ores, therefore, would save material that is now being irretrievably lost. The successful large-scale concentration of law-grade ore in the last few years on the Lake Superior iron ranges should encourage the attack of similar problems in the Birmingham district.

Jan 1, 1917

By Donlad B. Lindsay

This report describes a field-test program to determine the effectiveness of a polymeric wall sealant to reduce the excape of naturally occurring radio-active gas radon from the walls of an underground uranium mine into the ventilation air. A 75-foot-long, dead-end drift with a surface area of about 6,000 ft2 was used as the test site in which the average natural radon flux from the normally dry rock was 16 fCi/cm2-s. The effect on radon emanation of wetting the walls with water to a depth of 3 inches was tested, after which the rock was completely covered with a coating of dry-mix concrete to provide a base for the sealant, an acrylic latex. Sealant was applied in two coats to about 0.25 mm thick. An overall reduction of average radon flux of about 75 pct was achieved. Radon production and other environmental values were measured continuously and automatically by a Bureau of Mines data acquisition system. A commercial microcomputer was programed to convert raw data to engineering units and to perform other useful operations while recording all data on magnetic diskettes. Direct measurements of radon flux from the rock surface were made by a charcoal adsorption technique.

Jan 1, 1981

By Turíbio Tanus Sales

Este trabalho descreve a implantação do sistema IBA na fábrica de tubos sem costura da VSB, a mais nova e mais automatizada do país. O trabalho destaca os bons resultados alcançados utilizando o IBA como ferramenta de manutenção e da inovadora visão do IBA na VSB, aonde rompeu as fronteiras da manutenção e atingiu as áreas de produção, desenvolvimento técnico e qualidade. A implementação do IBA na VSB teve grande relevância para a eficiência do comissionamento e start-up da fábrica de tubos. A capacidade de aquisição de dados em alta velocidade associada às diversas funcionalidades de análise de dados propiciaram meios de aprendizado sobre o processo, identificação rápida de problemas e difusão de conhecimento. Todavia, na VSB, a ferramenta extrapolou os limites da manutenção e alcançou funcionalidades também nas áreas de qualidade, produção e desenvolvimento técnico. Outra funcionalidade desenvolvida pela VSB no IBA foi a capacidade de analisar oscilações de variáveis de processo ao longo do comprimento dos tubos produzidos e não só ao longo do tempo, como usualmente é feito. A capacidade do IBA PDA na aquisição rápida de dados possibilitou fazer ajustes finos nos tempos de ciclo de cada equipamento, deixando a medição mais elaborada e precisa, auxiliando a identificação dos locais que são gargalos de produção. A possibilidade de visualizar, com resolução de milissegundos, os eventos que ocorrem ao longo do tempo, ajudou a reduzir o tempo de análise e correção de falhas.

Jul 30, 2018

By Richard F. Hewlett

This report describes how a limited number of preliminary exploration drill-hole assays from a mineral deposit can be used to design grid spacing that is both economic and efficient for subsequent evaluation drilling of that deposit. Relationships between desired precision of the estimate of grade of ore and drilling cost are used to determine the economic drill-hole spacing. The statistical concept of precision in estimating grade of ore is used to determine the efficient drill-hole spacing. Assay data from approximately 50 known copper deposits were studied, and the relationships of the statistical parameters of these deposits were computed. Drilling requirements for various precisions of the estimates of grade of ore were computed for some of these known deposits to serve as guides for drilling future copper deposits. The effect of various geologic factors on the trend in grade of ore and, therefore, on the drilling requirements is shown for certain deposits.

Jan 1, 1965

By J. W. Adams

This report surveys the efforts of six contractors to the U.S. Bureau of Mines with regard to their electromagnetic noise measurement programs. What has been done, what is planned, and evaluations and recommendations are given for each contractor. The main observation is that to date there is not sufficient knowledge of electromagnetic interference in mine environments to design a reliable communication system. This knowledge should be available by the end of June 1972 if certain planned programs are completed successfully. A major effort of this report is to establish parameters to be measured, units to be used, and workable formats for data presentation. This is given in Appendix A. Some details concerning equipment, procedures, locations, and sample data are included in Appendix B.

Jan 1, 1971

By Aline Tatom

This paper presents numerical and experimen¬tal results dealing with the application of ferric ion oxidation of uranium in acidic media. Conclusions are derived from matching numerical results to experimental data taken on one-dimensional laboratory leaches using ore from a South Texas Coastal plain deposit. Since the numerical results can be made quite general, we are able to extract and quantify the effects of oxidant concentration, flow velocity, mass transfer, chemical kinetics, and competitive oxidant consumers (pyrite and molybdenite) on the experimental results. Our results suggest that the leaching of uranium is a mass transfer controlled while that of pyrite is kinetically controlled.

Jan 1, 1981

By T. B. Nolan, R. N. Hunt

In terms of present metal prices, analysis of extant records of the Eureka district indicate past production of the magnitude of $200,000,000 in recovered silver, lead, and gold. Production to date has been thoroughly oxidized ore from massive replacements, fissures, manta, and pipe-like bodies-in large part from the massive Eldorado (middle Cambrian) and Hamburg (middle to late Cambrian) dolomite horizons. In the productive area of about 6 square miles carbonate rocks comprise 80 per cent of the section, which includes early Cambrian to late Ordovician horizons. Four-fifths or more of the district's production came from a block of Eldorado dolomite in Ruby Hill that was moved in over younger horizons on strands of a regional thrust fault. The lower 500 to 600 feet of the block was much fractured and brecciated and became host to the ores. The Ruby Hill fault, a late normal fault, limits the Ruby Hill block of dolomite on the north for its entire length of nearly a mile and terminates the downward extent and exploitation of its ores. It introduced an hiatus of some 40 years in the district's development. Drilling of the past 20-odd years, followed by underground work, has now exposed the down-faulted extension of the Ruby Hill block of Eldorado dolomite and its contained ores, dropped 1800 feet in a dip shift to depths beneath the surface of 2000 to 3000 feet. The ores at depth are the sulfide counterpart of those mined in early years on the footwall side of the fault. The ores of the district may be attributed to the same source as the intrusive quartz diorite outcropping in a limited way south of Ruby Hill but found at depth elsewhere in drill holes. The long north-south axis of the district, its anticlinal structure, its major faults, and the distribution of the intrusives and, in their relation to the surface, the ores themselves, all suggest that erosion has not cut deep enough to expose the extent of intrusives and the ores consequent upon them.

Jan 1, 1968

By E. P. Youngman

In the Unfederated Malay States, with the exception of Johore, the rights of suzerainty, protection, and administration were transferred by giam to the British Government in 1909. In the States of Kelantan, Trengganu, Kedah, and Perlis, the rulers are assisted by State Councils and by British advisers appointed by the British Government.3 With respect to Johore, the largest, richest, and most highly organized of the Malay States not in the Federation, the treaty of December 11, 1885, with Great Britain, defined the relations of the State to the British Govern- ment and allowed the Maharaja to assume the title of "Sultan"; an amendment to this treaty (May 12, 1914) provided that the Sultan should be advised by a British officer, the General Adviser. ...... The political organization of the States is reflected in the mining legis- lation, Johore being the only one having a comprehensive code. The mining enactments now in force, according to the High Commissioner for the Malay States, are as follows:

Jun 1, 1932

By Alberto Nei Carvalho Costa

Devido às novas tendências de design de carrocerias de automóveis, as peças pertencentes a estas carrocerias apresentam características de fabricações cada vez mais críticas, principalmente relacionadas ao processo de estampagem. Uma forma de atuar neste processo para evitar perdas de produtividade, principalmente com o rompimento do material, é atuar na lubricidade entre o material e o ferramental do equipamento. A aplicação do óleo lubrificante na bobina de aço é uma forma de atuar na lubricidade, mas devido à criticidade de estampagem que determinadas peças apresentam, somente o óleo lubrificante não é suficiente para este fim. Visando atender essa necessidade, a CSN e seus fornecedores desenvolveram um sistema de lubrificante para seus aços, conhecida como tecnologia de pré-fosfato. Este trabalho tem como objetivo apresentar as vantagens fornecidas pelo aço pré-fosfatizado no que se refere a estampagem crítica de peças automotivas, bem como avaliar o seu impacto no processo de pintura automotiva. Como resultado verificou-se que a camada de pré-fosfato impactou na redução do coeficiente de atrito do aço zincado de forma suficiente para confecção de peças críticas de carrocerias de automóveis. Verificou-se também que o filme de pré-fosfato é totalmente removido na etapa de desengraxe do processo pintura automotivo, não prejudicando as etapas subseqüentes do processo: fosfatização e pintura.

Jul 30, 2018

By John Convey

This paper, a follow-up to an earlier study, gives the history of Canadian developments in mineral processing from 1921 to the fall of 1964. It deals extensively with comminution and flotation, and then goes on to cover the fields of gravity concentration, magnetic concentration, cyanidation, the processing of uranium ores, and instrumentation. Several outstanding examples of installations are given. The paper concludes with a discussion of present-day trends in mineral processing. Introduction T HE history of the developments in mineral processing in Canada from its earliest times to 1920 has already been published by one of the authors (1). The present paper is thus a logical follow-up to bring this history to date. From 1834 to 1920, mineral processing in Canada, as elsewhere in the world, was in its formative stage. This, however, prepared the ground for developments that have resulted in a mining empire from the Atlantic to the Pacific, a mining empire which could be said to be almost on par with that in the United States.

Jan 1, 1965

By R. E. Siemens, Gary L. Hundley

The Bureau of Mines has devised and demonstrated a process for recovering Ni and Co from low-grade domestic laterites . The process consists of four mmaajjoorr steps : ( 1 ) reduction roast , ( 2 ) ammoniacal leach , ( 3 ) solvent extraction , and ( 4 ) electrowinning . Several solid - liquid separation steps are required that affect the economics of the overall process . In this study , two techniques for solid - liquid separation , centrifugation and thickening , were investigated . This report presents the results of ( 1 ) laboratory and pilot plant studies to determine parameters for sizing centrifuges and thickeners and ( 2 ) an economic study of the two techniques , based on the requirements of a commercial - size ( 5,000 - tpd ) laterite processing plant . Sizing and other equipment - related recommendations , based on data from the Bureau's studies , were obtained from commercial manufacturers . The costs of thickening and centrifugation , including all the unit operations affected , were determined by the Bureau's process evaluation group . The total operating costs for separation using the two techniques ( including depreciation on the capital cost of equipment ) were found to be quite close : $ 17.26 per ton of laterite for centrifugation and $ 18.15 per ton of laterite for thickening . For centrifugal separation , the greatest cost was found to be the initial capital cost for the separation equipment ; using thickeners , the greatest cost was for reagent recovery .

Jan 1, 1983