Search Documents

By R. Owens, C. Roos, B. Hill, S. Rosenthal

It is common practice, and even legally required in many jurisdictions, to design two-lane haul roads in open pit mines to three and a half times the widest dimension of the haul trucks operating on the road. In open pit gold mines with high strip ratios, the road width has a significant impact on the economics of a design. It is possible to minimize the flattening of the highwall if the road width is reduced, assuming the width used is not needed to flatten the slopes for geotechnical purposes. With the use of autonomous haulage and pullouts, it may be possible to operate safely and efficiently on a reduced road width of two times the width of the hauling equipment.

Mar 2, 2022

By Éder Domingos Oliveira, Carlos Antonio Morais, Ruberlan Gomes Silva

The objective of this study is to assess the impact of different reagents, such as limestone, lime, magnesium oxide, and sodium hydroxide, in experiments carried out in the single purification step and in two consecutive purification steps by raising the pH of a rare earth sulfuric liquor with the aim to remove or reduce the impurity concentrations in the rare earth sulfuric liquor. The choice for the best purification condition was made based on the minimum loss of rare earth elements (REEs), reagent consumption, and residue generation. The exploratory experiments show that it takes place in the two consecutive purification steps, the first one consists in dosing the limestone pulp until it reaches a pH of 3.5 followed by an addition of a lime pulp reaching a pH of 5.0. Under this condition, the results were a total removal of Fe3+, PO4 3− , and Th4+ ions and a reduction of 99%, 87%, and 37% w/w in the Al3+, UO2 2+, and SO4 2− concentrations, respectively, in the purified rare earth liquor. Furthermore, the lowest REE losses (8.3% w/w) and reagent consumption (4.3 kg/m3 ) and also a low residue generation (7.5 kg/m3 ) were observed in this condition. Despite reaching similar results regarding impurity removal, the experiments done with the addition of limestone, lime, magnesium oxide pulps, and sodium hydroxide solution in the single purification step, where the pH was raised to 5.0, presented higher REE losses (64.9%, 42.5%, 44.8%, and 60.9% w/w, respectively) and a higher residue generation (43.2, 25.1, 11.1, and 13.6 kg/m3 , respectively). This occurred due to the co-precipitation of salts containing rare earth elements in their composition. The experiments conducted with limestone, lime, and MgO resulted in a higher consumption of reagents, while the same result was observed when NaOH was used (4.3 kg/m3 ). In the experiments carried out with the addition of magnesium oxide and sodium hydroxide, the respective purified rare earth liquors presented a high concentration of magnesium, sulfate, or sodium, which could impact the quality of the marketable rare earth salts, whereas the salts obtained under the best condition observed in this study seem to be amenable for use as raw material in an attempt to obtain rare earth products with an acceptable chemical quality.

By Éder Domingos Oliveira, Carlos Antonio Morais, Ruberlan Gomes Silva

The objective of this study is to assess the impact of different reagents, such as limestone, lime, magnesium oxide, and sodium hydroxide, in experiments carried out in the single purification step and in two consecutive purification steps by raising the pH of a rare earth sulfuric liquor with the aim to remove or reduce the impurity concentrations in the rare earth sulfuric liquor. The choice for the best purification condition was made based on the minimum loss of rare earth elements (REEs), reagent consumption, and residue generation. The exploratory experiments show that it takes place in the two consecutive purification steps, the first one consists in dosing the limestone pulp until it reaches a pH of 3.5 followed by an addition of a lime pulp reaching a pH of 5.0. Under this condition, the results were a total removal of Fe3+, PO4 3− , and Th4+ ions and a reduction of 99%, 87%, and 37% w/w in the Al3+, UO2 2+, and SO4 2− concentrations, respectively, in the purified rare earth liquor. Furthermore, the lowest REE losses (8.3% w/w) and reagent consumption (4.3 kg/m3 ) and also a low residue generation (7.5 kg/m3 ) were observed in this condition. Despite reaching similar results regarding impurity removal, the experiments done with the addition of limestone, lime, magnesium oxide pulps, and sodium hydroxide solution in the single purification step, where the pH was raised to 5.0, presented higher REE losses (64.9%, 42.5%, 44.8%, and 60.9% w/w, respectively) and a higher residue generation (43.2, 25.1, 11.1, and 13.6 kg/m3 , respectively). This occurred due to the co-precipitation of salts containing rare earth elements in their composition. The experiments conducted with limestone, lime, and MgO resulted in a higher consumption of reagents, while the same result was observed when NaOH was used (4.3 kg/m3 ). In the experiments carried out with the addition of magnesium oxide and sodium hydroxide, the respective purified rare earth liquors presented a high concentration of magnesium, sulfate, or sodium, which could impact the quality of the marketable rare earth salts, whereas the salts obtained under the best condition observed in this study seem to be amenable for use as raw material in an attempt to obtain rare earth products with an acceptable chemical quality.

By Fabiana Fonseca de Morais

A sinterização é um dos mais importantes e mais antigos processos de aglomeração da indústria metalúrgica. Entender a realidade atual do processo de sinterização e as qualidades requeridas para o sínter é primeiro passo para o desenvolvimento de equipamentos ou processo. Este trabalho visa entender o impacto das diferentes características de minério e resíduos empregados em uma sinterização, seu comportamento na qualidade do sínter e a sugestão de equipamentos para amenizar problemas encontrados. Parâmetros como CaO/SiO2, SiO2, Al2O3 e MgO são avaliados para entender a tendência do mercado e o efeito na qualidade final do sínter. A correta avaliação das necessidades da planta para otimização dos equipamentos a matéria-prima disponível se faz necessário para o melhor resultado no alto-forno. A granulometria da matéria-prima também é um ponto importante a ser analisado. O sinter feed tradicionalmente possui uma maior fração entre 0,7 e 6 mm, uma fração menor entre 0,2 e 0,7 mm e um conteúdo de ultrafino (<0,150 mm) limitado a 15%. Estudos identificam uma tendência do sinter feed com maior conteúdo de sílica e o consequente aumento da utilização de ultrafinos. Como resposta ao incremento de ultrafinos na sinterização as grandes siderúrgicas já estão investindo em equipamentos que minimizem grandes perdas de produtividade, como a instalação do misturador intensivo, utilizado em projetos da Pau Wurth. Outra solução inclui a instalação de uma mini-sinterização dedicada para receber este material mais fino e resíduos. O sínter produzido poderá ser adicionado diretamente no forno e/ou ser utilizado como nuclueante na sinterização grande para aumento de sua produtividade.

Aug 16, 2017

[Module 10. Internally Cued Operating Contingencies Prerequisite: Modules 1-7 - Estimated Instructional Time: 2.42 hrs. Module Abstract Trainees, using programmed instruction, describe the cues, consequences, operational sequences, and possible causes resulting from loss of air pressure from power fluctuations, and from a failure of the automatic lubrication system. Although some of the contingencies may be initially signaled by an alarm or from the oiler, each trainee will demonstrate proficiency in the appropriate operating techniques and procedures. This module also includes a review component for those trainees identified in the assessment exam as requiring less detailed instruction.]

Jan 1, 1976

By C. W. K

This little sketch of the late Willet G. Miller, Provincial Geologist of Ontario, is intended to be neither a biography of his career nor a eulogy of his life. His biography has already been written in an incomparable manner by Mr. T. A. Rickard, his eulogy by Canon Cody. What more can be said of Dr. Miller than is summed up in the words of that great Canadian divine, Canon Cody, that he was "Big in body, big in heart, and, as we learned, big in brain." This article, then, will merely record a few personal reminiscences of the man himself, and while they are necessarily disjointed, they may at least serve to illustrate certain traits in his character which are not generally known or appreciated outside of the circle of his intimate friends. In the latter part of May in the year 1904, Willet G. Miller, with two? assistants, set out for the small village of Haileybury to begin his geological work in the area a few miles to the south which he was soon to name Cobalt. At that time the Timiskaming and Northern Ontario railway was not finished, although the right-of-way was cleared and partly graded. The nearest railway station was on the Canadian Pacific at the south end of lake Timiskaming, from which point the old steamer Meteor carried passengers and freight up the long, narrow and deep waters of lake Timiskaming, a very pleasant trip of some sixty miles. On this particular trip there was a fairly large crowd on board consisting of settlers going into the clay belt north of lake Timiskaming, of lumbermen, and of a few merchants and commercial travellers who were interested in the small business centres of Haileybury, New Liskeard and Ville Marie. Scarcely any attention was paid to the reports of the newly found silver deposits, although the daily papers had announced discoveries in the district six months before. As a matter of fact, the chief excitement on board was afforded by a moose, which, in swimming from the Ontario to the Quebec shore of the lake, crossed the bow of the boat, the captain steering to within a few yards of the terrified animal.

Jan 1, 1925

By J. C. Williams, M. J. Blackburn

MANY aspects of the formation of the metastable w phase in titanium-transition metal alloys have been described in several recent papers.1-4 These papers have reviewed earlier work on the w phase and have further defined most of the important features related to the formation of this phase, e.g-., its crystal structure, composition, and morphology. There are, however, several important points regarding formation of the w phase in titanium alloys which have been described in less detail. Two of these are the relationship between lattice misfit and w phase morphology and the influence of lattice misfit on the mode of formation of the equilibrium a phase. In this communi- cation we will present transmission electron microscopy results relevant to these two points. The alloys used in this study were prepared by non-consumable electrode arc melting, each 30-g button being remelted a minimum of twelve times. The alloy compositions we have studied are listed in Table I. Thin foils were prepared using standard techniques described elsewhere. Two distinct c' phase morphologies have been reported in earlier papers. The phase is ellipsoidal in the Ti-Mo3 and Ti-Nbl system and cubical in the Ti-V3 system. Results of the present study show that the w phase is also cubical in Ti-Mn, Ti-Fe, and Ti-Cr alloys as illustrated in Fig. l(b) to (d). Fig. l(a) shows the ellipsoidal morphology in Ti-MO3 for comparison purposes. It was suggested in an earlier paper3 that the w phase morphology may be controlled by the lat-

Jan 1, 1970

By Susan M. Moore

Many challenges are faced by workers in lower-seam (42 inches or less) mines. The lower-seam heights confine mine workers to their knees as they perform their daily tasks such as installing roof bolts, delivering supplies, repairing belt, or cutting coal. Miners working in these lower seams often consider kneepads to be their only line of defense against knee injuries. However, healthy knees do not start and stop with kneepads. Other interventions such as changing postures, proper hygiene, and work station design may also be used to reduce mine workers? risks for developing knee injuries. Incorporating these and many other interventions into a mine worker?s ?way of life? is an important step to ensuring a long, healthy career and retirement. Keeping knees healthy is also a key aspect to reducing costs in low-seam mines as the industry battles rising health care costs, and training/recruitment of replacement workers is time-consuming and costly. Educating the workforce about the possible interventions to reduce knee injury risk is a primary objective for the National Institute for Occupational Safety and Health?s (NIOSH) Pittsburgh Research Laboratory (PRL). Therefore, NIOSH researchers, along with industry and academia, developed a training package to educate the mining com­munity about some possible interventions beyond kneepads that may be used to help decrease knee injury rates. Increased awareness and simple changes are the first steps to reducing knee injuries.

Jan 1, 2008

Jan 1, 1929

By J. F. Poland

B. C. Burgess-—Prior to hearing this paper presented at the San Francisco meeting, I travelled by car from Yuma, Ariz., across south-central California and up through the San Joaquin Valley. After hearing the paper I returned by the coast route to San Diego then along the Mexican border to Yuma. The striking feature of these trips, related to this paper, was the dry river and creek beds at a time of year not the dry season. Contrasted with this was the wasteful use of water in irrigation canals and laterals. Poland says "at least 90 pct of the ground water pumped is used for irrigation." That being the case, it would appear that first consideration should be given to conservation of this use. Probably a small part of this is actually reaching the plants. Some measure of this loss between pump and crops would be revealing. Methods that might be employed to reduce this loss are pipe lines and spraying of some crops such as the banana planters are using in Central America. Another idea which might be investigated is to line canals and ditches with some water-repelling mineral like pyro-phyllite. Perhaps a comparatively thin sprayed-on

Jan 1, 1951

By J. F. Poland

B. C. Burgess-—Prior to hearing this paper presented at the San Francisco meeting, I travelled by car from Yuma, Ariz., across south-central California and up through the San Joaquin Valley. After hearing the paper I returned by the coast route to San Diego then along the Mexican border to Yuma. The striking feature of these trips, related to this paper, was the dry river and creek beds at a time of year not the dry season. Contrasted with this was the wasteful use of water in irrigation canals and laterals. Poland says "at least 90 pct of the ground water pumped is used for irrigation." That being the case, it would appear that first consideration should be given to conservation of this use. Probably a small part of this is actually reaching the plants. Some measure of this loss between pump and crops would be revealing. Methods that might be employed to reduce this loss are pipe lines and spraying of some crops such as the banana planters are using in Central America. Another idea which might be investigated is to line canals and ditches with some water-repelling mineral like pyro-phyllite. Perhaps a comparatively thin sprayed-on

Jan 1, 1951

By Daniel R. Stewart

The function of the geological engineer is to assist in mine planning and operations by collecting, interpreting, and applying geologic data to the solution of engineering problems. The geologist supports this effort by collecting additional geologic information specifically useful to the engineer. This use of geologic information reinforces the value of mine geology to the mining process beyond the traditional role of orebody definition. Work discussed includes: evaluation of caving strategies at the Climax and Henderson mines; support definition and slope stability at the Climax mine; and some uses of geology in cavability estimation for the Mount Emmons project.

Jan 1, 1983

By Mark Eisner

ONE'S JOB is the watershed down which the rest of one's life tends to flow write the Lynds in the first pages of their classic social study, "Middletown in Transition." Certainly engineers will confirm this statement after a check among those in their own profession with whose lives they are at all familiar. I have no hesitancy in acknowledging the truth of their observation for the men and women who are engaged in the profession of the law. It has been often remarked that American public life is overrun with members of the law profession. The highest public office in the land, that of President. has been occupied by lawyers almost to the exclusion of citizens of any of the other professions. Twenty-two Presidents of the United States out of the total of 31, were members of the bar. For the most part, members of Congress, the governors of the states, the state legislators and the mayors and other local leaders, men who occupy important positions of responsibility and public trust, have had legal training. Now this fact is no mere accident. Those who were fitted for the "job" of the practice of the law are favorably placed with respect to their participation in public life. Thus public service and public office is the watershed down which the "lawyer's" life tends to flow.

Jan 1, 1940

By E. H. Sellards

ON Oct. 9, 1929, a sink formed in the Sour Lake salt dome oil field in Texas, and on Oct. 12 a second smaller sink formed at the north margin of the first. The purpose of this paper is to give such observations as it has been possible to make on the earth movement incident to this subsidence. Sour Lake salt dome is typical of the salt domes of the Gulf Coastal Plain of Texas. Structurally the dome is a plug of salt which rises to within 900 ft. or less of the surface. Above the salt is a cap rock consisting of anhydrite with more or less calcium carbonate. The salt plug, as contoured on the cap rock, is circular in outline with, however, some appreciable irregularities. Overlying the cap rock are relatively uncompacted sediments consisting of sand, clay and gumbo.. At the crest of the dome these deposits are no more than 700 or 800 ft. thick. However, the sides of the dome are steep, and the sediments thicken rapidly away from the crest. The sink formed about 1500 ft. northeast of the crest of the dome where the sediments overlying the cap rock are from 1000 to 1200 ft. thick. The cavity permitting the subsidence was quite certainly either in the cap rock or in the salt below the cap rock, so that the sink was formed by the caving of as much as 1000 or 1200 ft. of earth.

Jan 1, 1930

By D. A. Riva

"The Line Creek Project is located in southeastern British Columbia, approximately 25 kilometres north of Sparwood. The design is to produce a total of2.7 million tonnes of coal annually. This is made up of1.4million tonnes of thermal coal and 1.3 million tonnes of metallurgical coal.Construction commenced in the spring of 1980 and mining operations began in July 1981. The thermal processing plant, maintenance and dry facilities, as well as extensive road and bridge construction, were completed in early 1982. A collective agreement was signed with the International Union of Operating Engineers, Local 115, in June 1981.The first unit train left Line Creek on February 18, 1982 with a load of thermal coal bound for the Ssangyong Corporation in Southern Korea. It was the start of a ten-year contract to supply 350,000 tonnes annually to fire their cement kilns. Additional contracts for 750,000 tonnes will fuel the boilers of Korea Electric Company's San Chon Po and Go-Jeong power stations. Metallurgical coal shipments are scheduled to leave the Roberts Bank port in Vancouver in April 1983.Tracking an introductory presentation given at the 1981 CIM Annual General Meeting in Calgary, this paper highlights the salient developments by which ""The Line Creek Project"" has progressed during the past year to the"" Line Creek Operation"". Line Creek has com e on stream as scheduled and will meet all contractual commitments pertaining to timing, volumes and quality for thermal coal. The first train load left the plant in mid-February, and the first boat load to Korea departed Roberts Bank in mid-April. Metallurgical coal deliveries will commence in April 1983."

Jan 1, 1982

By Robert J. Anderson

"Introductory Statement:In melting the nonferrous metals and alloys for foundry and rolling-mill work, even with the best practice, there is always a loss, due principally to oxidation. Melting losses are a serious source of financial loss in brass and bronze practice, but they are especially serious in the case of aluminum and its light alloys because of the relatively high price of aluminum. The indications are that the melting losses in many aluminum foundries of the United States are at times high, and in some plants (especially where certain furnaces are used) they are entirely too high when compared with the average practice. The fact that the oxidation losses in melting aluminum and its light alloys are high is well known, but it is doubtful whether the factors governing the most suitable methods of melting for a minimum of dross are equally well known. The metal losses involved in melting are worthy of especial attention now because of the rapidly growing importance of the aluminum industry.Factors in the operation of furnaces which affect metal and fuel losses:The essential requirements in the commercial melting of any metal or alloy are that the melting losses should be low, the melting should be rapid, and the melting cost should be low. Certainly it may not be possible to obtain these requirements in any furnace selected at random, and it follows that the design and the operation of furnaces for melting different metals are subjects that warrant the most extensive study and tests. As a general rule, in the industrial operation of furnaces, run on aluminum and aluminum alloys, an effort is made to keep the dross and oxidation losses as low as possible. In attempting to hold dross losses low, numerous factors involved in metal melting may be overlooked, or at least disregarded, and the net practical result may be that the furnace is exceedingly wasteful of fuel. In the case of aluminum and its light alloys, the effect of increasing the temperature of melting, at least in an atmosphere containing free oxygen and nitrogen, is to increase the net melting loss."

Apr 1, 1921

Jan 1, 1957

By Guy Demers

"This paper defines the responsibilities and functions of the Maintenance Department, and its organization, physical and human assets, highlighting the unique operating problems. Due to the self-sufficient aspect of the Asbestos Hill Deception Bay project, the Maintenance Department cover-s fields that are numerous and very dissimilar: production, mobile, processing, service, power generation, fire protection, heating, water and sewage disposal equipment. Added to this, buildings, plant and camps, wharves and communications equipment all demand versatility, adaptability and expertise from maintenance personnel. Good maintenance practices are a necessity in this environment and are more critical than at southern locations; that is, high-quality replacement material, complete and well-controlled preventive maintenance, major repairs on a component-replacement basis, updated inventory, efficient training and permanent contacts with suppliers, combined with an equipment improvement program, updated specifications on lubricants, hoses, seals, filters, etc., are mandatory. The seasonal aspect of the operations applies a great deal of pressure on the maintenance team, as the production months do not permit major repairs. Short- and medium range planning and accurate evaluation of equipment conditions highly influence production efficiency. Maintenance control, planning and scheduling do not follow the accepted standard routines, as personnel turnover normally does not permit an accumulation of knowledge of the equipment history and condition by the •individual tradesman."

Jan 1, 1976

By John B. Cook

Most of today's open pits take the form of conical-shaped excavations in the relatively flat or undulating terrain surrounding them. Ore is usually hauled uphill from the pit bottom by truck, rail, or skip to crushing, beneficiation, railroad loading, and stockpiling facilities near the edge of the pit. There are, however, a few orebodies whose locations in mountainous terrain causes special problems that generate different technical solutions. LAMCO's 10.5 million metric tons per year high-grade iron mine in the Nimba Range in tropical Liberia is probably one of the most extreme of these exceptions (Fig. 1). At Nimba there is a 2,000-ft difference in elevation between the upper- most levels of the orebodies and the start of the railroad below at the foot of the mountain. Haulage to the crusher is usually downhill at grades of up to 12% dictated by the topography of the rugged terrain. Ore is transported from the crusher down the mountainside by a conveyor sys- tem 10,096 ft long, whose average grade is 18%. The belt is braked by asynchronous generators, feeding power into the local network. The original crusher must be relocated at a lower elevation outside the final pit limit to allow that part of the mountain on which it now stands to be excavated. HISTORY The LAMCO Joint Venture is owned 75% by the Liberian-American- Swedish Minerals Co. (LAMCO) and 25% by Bethlehem Steel Corp. LAMCO is comprised of a 50% interest by the Liberian Government and 50% interest by Liberian Iron Ore Ltd (Fig. 2). This joint venture was launched to develop the high-grade iron ore deposits of the Nimba Range.

Jan 1, 1969

[†AARONSON, ALFRED E., Vice-Pres., Mid-Co. Petroleum Co., Mid-Co. Bldg., Tulsa Okla. '18 ABADIE, EMILE R., Min. Engr Box 927, Porterville, Cal. '76 ¦ABADILLA, QUIRICO A. Student, Colorado School Of Mines, Golden, Colo. '20 ABBOTT, CLARENCE E., Gen'l Supt. Iron Mines Div., Tenn. Coal, Iron & R. I. Co., 1405 Minnesota Ave., Bessemer, Ala. '04] [ ]

Jan 1, 1925