Search Documents

The Institute has set important objectives for 1988 to make the Institute still more purposeful. Precious metals The Second International Symposium on Mining, Extraction, and Processing of Precious Metals will be held in Las Vegas, Nevada, USA, during the 118th TMSAIME Annual Meeting in March 1989. The First International Symposium on Precious Metals.

Jan 1, 1987

By Richard P. Stahura

During the next five years, there will be a trend toward performing belt cleaner maintenance while the conveyor is in operation. Most mines and industrial sites that use belt conveyors have an in-house safety rule that the belt must be stopped before maintenance work can be performed on any belt-cleaning device. This is a good rule. Most cleaning devices are positioned against the belt with hardware that requires the service technician to reach or climb into the chute to change the cleaning blades. But this simple rule becomes more complicated as production demands require higher conveyor availability and provide fewer conveyor outages. In many cases, today’s conveyors are expected to be available 98% to100% of the time.

Jan 1, 1996

By J. P. Wilson, T. Cook, H. Kling

The Tessenderlo-Kerley Leachprocess has been shown to be effective in the removal of residual copper from molybdenite concentrates. Concentrates of varying mineralogy, including those containing relatively large amounts of chalcopyrite, have been successfully leached on laboratory and pilot plant scales. The lixiviant system is ammonia andammonium bisulfite with air / oxygen addition. An abrasive is added which greatly enhances the kinetics, and it is subsequently screened out and reused. The dissolved copper is easily recovered using existing technology. Extraction profiles, reagent consumptions, and mineralogical data are presented.

Jan 1, 1999

By Ch. R. V. S. Nagesh, Ramesh Naidu Mandapati, Venkata Swamy Nalajala, Tondepu Subbaiah, Naga Jyothi Kothamasu

Leaching studies of magnesite obtained from Tamilnadu Magnesite Limited, Salem, have been carried out using hydrochloric acid leaching and percentage of magnesium chloride recovered was estimated. The variables considered in this study were the following: duration of leaching, volume percentage of hydrochloric acid, temperature, and pulp density. Percentage recovery of magnesium chloride increased with duration of the leaching, volume % of concentrated hydrochloric acid, and temperature. Percentage recovery of magnesium chloride decreased with increase of pulp density. The optimum conditions found to be pulp density (10%), hydrochloric acid concentration (30%), duration of leaching (2 h), and temperature (348.15 K). Iron was removed by treating the leach liquor with hydrogen peroxide and by raising the pH to 3.5–4. The purified leach liquor was subjected to spray drying for producing high pure magnesium chloride.

Jun 7, 2022

I have headed this paper with a question and for the impatient among you ûthe answer is no we have not run out of developments but, and it is a big æbutÆ, we need to be innovative and ahead of the game or ænoÆ will be æyesÆ before we know it.Why do I believe that our future lies in innovation? Thirty years ago, knowledge doubled every 14 years. It is now doubling every seven years. In 1965, Gordon Moore, one of the founders of the chip maker Intel, made an observation that growth in memory chip performance is doubled every 18 months which became known as MooreÆs Law. Now there is fibre law, where the transmission line capacity doubles every nine months and storage capacity, under disc law, doubles every 12 months. What does this mean? Well, firstly there is a massive rise in information flow and availability with no limits in growth for at least the next ten years. Secondly, unlike our grandfathers, we are most unlikely to be employed by the same firm for our working career - we may not even have the choice to stay with the same company. In a phenomenon Richard Foster and Sarah Kaplan (2001), borrowing from Schumpeter, termed æcreative destructionÆ, companies are unable to sustain market-beating levels of performance for more than ten to 15 years. In the 1920s the turnover rate of companies in the United States was 1.5 per cent, so a company could employ almost three generations from the one family. A company had a half life of 60 years. In other words, you could well be in the same working environment as your grandparents. Today the churn rate is estimated to be eight to ten per cent. A company has a half life of five to six years. So for large companies, as an employer or employee or as a contractor, your working environment has a 50 per cent chance of changing in five years. Innovation is the driver of this rapid rate of change. Innovation is not for the faint hearted (Cutler, 2001) but it is the core for success in the global economy. The rate of change in our world is not going to decrease. We must learn, not only to manage change, but to enjoy the process of changing û to ride the tsunami of the knowledge economy.

Jan 1, 2002

By D. G. MacBeth

Most belt scales on the market are factory calibrated to minimum accuracy figures of 0.1% - 0.2% at several load points. However, if the same belt scale is not properly installed and maintained on the customers conveyor then the scale will not measure up to the claims of the manufacturer or to the requirements of the operator.

Jan 1, 1975

By Mariana Carla Mendes Rodrigues

Os aços ferramenta para trabalho a frio são utilizados em diversas aplicações em decorrência de propriedades como elevada estabilidade dimensional, alta resistência ao desgaste e elevada temperabilidade. Tais características estão diretamente associadas à microestrutura do material, isto é, à quantidade, à distribuição, ao tipo e à morfologia dos carbonetos presentes e à quantidade de martensita revenida e austenita retida. Neste contexto, no presente trabalho foram caracterizados mecanicamente e microestruturalmente quatro aços ferramenta para trabalho a frio empregados na fabricação de cilindros de laminação a frio. Para isso, amostras foram retiradas dos próprios cilindros e foram realizadas análises de dureza, microscopia óptica, microscopia eletrônica de varredura, espectroscopia por energia dispersiva e espectroscopia de emissão atômica por plasma. De acordo com resultados, uma comparação entre as propriedades dos aços foi conduzida visando concluir qual deles é o mais adequado para a referida aplicação.

Aug 16, 2017

By Aline Silva Magalhães

Nas últimas décadas a crescente demanda por carros mais seguros, econômicos e menos poluentes exigiram das montadoras, siderúrgicas e comunidade científica investimentos na pesquisa e no desenvolvimento de novos materiais, tais como os aços avançados de alta resistência. Dentro deste contexto, neste trabalho foi realizada a análise da microestrutura e das propriedades mecânicas de um aço bifásico na condição inicial e submetido a tratamentos térmicos com aquecimento na região intercrítica e resfriamento brusco. Foram analisadas a proporção dos constituintes na microestrutura e as propriedades mecânicas por meio de microscopia óptica e eletrônica de varredura, de difração de raios X, dureza e de tração. Observou-se, em geral, que o aumento da temperatura intercrítica levou a uma elevação da fração de martensita e, consequentemente, influenciou de forma a aumentar os valores de dureza, resistência mecânica e diminuir a ductilidade.

Aug 16, 2017

By Thiago Cesar de Souza Pinto

Os teores de umidade (U) presente no minério de ferro, após o processamento mineral, se torna uma dificuldade para seu transporte marítimo à medida que este teor ultrapassar os limites de TML (Transportable Limit Moisture). O presente trabalho teve por objetivo a identificação dos mecanismos de secagem em concentrados de minério de ferro tipo sínter feed em unidade experimental de secador de bandejas em escala de laboratório. São apresentados e discutidos resultados em que os mecanismos identificados se revelam como água livre superficial e capilaridade, para a faixa de umidade de interesse (13<U<6%). Uma regressão não linear foi realizada identificando o peso das variáveis em estudo, permitindo assim um modelamento dos resultados de redução de umidade. O modelo apresentou boa aderência aos resultados experimentais com desvios menores que 10% entre os dados previstos e observados.

Aug 16, 2017

By V. Rajaram

R.C. Rex, Jr. V. Rajaram's paper does not accurately reflect the status of Eastern oil shale development as it stands today. Today, there are numerous firms and research organizations pursuing development of the Eastern oil shale resource. Details of the current projects can be found in the symposium proceedings for the 1985 Eastern Oil Shale Symposium held in Lexington, KY, in November 1985. Additionally, the comparison of the Paraho and HYTORT processes is invalid because the HYTORT process design used it not an accurate representation of the HYTORT process. I will briefly address this point. It is disconcerting to see the author reference hydroretorting work conducted at the Institute of Gas Technology (IGT) (circa 1978) in the introduction, which indicates hydroretorting (the HYTORT process concept) yields of up to 250% of the Fischer Assay oil yield, and then turn around and base the remainder of the paper on the 1981 "Synthetic Fuels From Eastern Oil Shale Report," which depicts the HYTORT process as yielding only 115% of Fischer Assay. Indeed, work conducted at IGT to 1981 indicates commercial oil yields for the HYTORT process would be in the range of 200% to 210% of Fischer Assay. A more thorough literature search by the author would have yielded a 1981 publication by Schora et al., entitled "Update on the HYTORT Process" presented at the Symposium on Synthetic Fuels From Oil Shale in Nashville, TN, October 1981. This paper thoroughly discusses the shortcomings of the referenced study with respect to the HYTORT process. For the interested reader, I can also recommend a June 1984 report entitled "An Economic Comparison of Five Process Concepts for Using Eastern Oil Shale," published by Los Alomos National Laboratory (LA-10106-MS, Parkinson et al., NTIS No. DE84-015981). This study applies a realistic HYTORT design (circa 1982) and indicates that HYTORT is the most econom¬ical method of processing Eastern oil shales (about $20/bbl less than Paraho). Additionally, completion of the HYTORT feasibility study in June 1983 by Phillips Petroleum Co., Bechtel Group Inc., HYCRUDE Corp., and IGT has resulted in development of designs that will make the use of HYTORT on Eastern oil shales even more economic. HYCRUDE Corp., a second-tier subsidiary of IGT, is involved in commercialization and licensing of the HYTORT process and is active in efforts to develop the Eastern oil shale resource. As such, I am disappointed to see outdated material that has the potential for adversely affecting development of Eastern oil shale resources published in MINING ENGINEERING. I can only hope that this response will serve to mitigate any negative opinions that may have been formed. Today, activity in commercializing Eastern oil shales dominates the oil shale scene in the US and indicates a realization of the potential for these shales. Reply by V. Rajaram I appreciate the updates on the HYTORT process provided by R.C. Rex, Jr. I hope that Hycrude's work will lead to the funding of a pilot plant to demonstrate that yields of greater than 200% of Fischer Assay can be achieved in a commercial plant using eastern US oil shales.

Jan 9, 1986

By Kaihui Yang

Volcanogenic massive sulfide deposits are generally considered to have been formed by hydrothermal fluids that leach ore metals out of footwall rocks. However, the necessity for a metal-rich magmatic component in the ore-forming fluid of "giant" ore deposits has been debated over the decades. The solution to this issue is important not only for metallogenic models but also for the mineral exploration. In the hydrothermal leaching model, massive sulfides at mid-ocean ridges are deposited from hydrothermal fluids containing 80 ppm Fe, 6 ppm Zn, 2 ppm Cu, 350oC, and 0.7 g/cm3 density (average data for 21oN East Pacific Rise). A simple calculation demonstrates that such a dilute fluid is unlikely to have been responsible for the formation of the largest ancient massive sulfide ores of greater than 100x106 tonnes, such as Kidd Creek, Brunswick No. 12, Neves Corvo, and Rio Tinto. For such a deposit consisting primarily of pyrite, sphalerite, galena and chalcopyrite (other minerals, including gangue, might account for an additional 10-20%) and even assuming 100% precipitation and retention of the sulfides, more than 790 km3 of vent fluid would be required. For typical water-rock reaction ratios of about 2, this fluid would have to have reacted with about 395 km3 of rock to acquire its metals by conventional leaching processes. This estimate, however, conflicts with the observation that even a giant massive sulfide ore body is usually underlain only by a few cube kilometers of obviously altered rocks. Moreover, this model is not consistent with the observation of hanging wall alteration in many large massive sulfide deposits. The close spatial association between massive sulfides and volcanic rocks, in both ancient and modern sea floors, suggests that direct magmatic contribution should be taken into account in the genetic model. Magmatic fluids, capable of carrying abundant ore metals and volatiles and escaping from magma by depressurization, are well known from modern active volcanoes on land. High concentrations of metals occur in CO2-rich magmatic fluid trapped in felsic volcanic rocks nearby large presently-forming VMS deposits in the eastern Manus Basin (Pacmanus, Suzette) and also in the footwall rocks of Ordovician giant Brunswick #12 deposit in the Bathurst district, New Brunswick. Only 1% of such metal-rich magmatic fluid mixed with heated sea water, that has leached its metals from rocks, would contribute 85% of the total metals to form an orebody. Such magmatic fluids are most likely to be formed from volatile-rich felsic magmas that are prevalent in back arcs, and, if added to the normal circulation system, the fluids could be responsible for the formation of "giant" ore deposits. If this is true, then the study of magmatic fluids in the seafloor volcanic rocks may provide criteria for the exploration of large ore deposits.

Jan 1, 2011

This report is the 23d in a series summarizing research and technologic work by the Federal Bureau of Mines on coal and related investigations; it is the fifth report to be issued on a calendar-year basis.2/ Publications by Bureau personnel in 1958 are cited;3/ in addition work in progress during the year is briefly described. To conserve our reserves of coal the Bureau of Mines conducts a program concerned with the development of fundamental information on coal characteristics and behavior, and the improvement of technology related to its production and utilization. The ability to anticipate and meet future demands for coal depends on a number of factors: (1) Knowledge of reserves from a stand- point of both quantity and quality; (2) the development of improved mining methods, health and safety measures, and preparation techniques that will insure its most efficient exploitation; and (3) knowledge of the controlling factors in efficient use of coal in combustion, carbonization, gasification, direct and indirect hydrogenation, and other new processes. The Bureau is concerned with each of these areas.4/,5/

Jan 1, 1960

By W. Beckering

IN CHARACTERIZING tars obtained by the low-temperature carbonization or North Dakota lignite, infrared spectra have been an invaluable aid in both qualitative and quantitative examination. Quite early it became evident in the tar-research program of the Bureau of Mines, U.S. Department of the Interior, that the small number of published spectra available for hydroxy aromatics would be inadequate for comparative purposes when dealing with the wide range of compounds present in coal tar; therefore, compiling a catalog of spectra was initiated as a continuing part of the tar program. As these spectra should be valuable to other investigators in this and related fields, they are being presented in this report. This group or spectra (figs. 1-98) represent 97 compounds, largely phenolic materials. The major problem of this project has been the availability of materials for examination. Samples have been obtained from commercial and private laboratories or synthesized at the Bureau of Mines Lignite Experiment Station, Grand Forks, N. Dak.

Jan 1, 1959

By Nicolangelo Del Busso

A soldagem é um processo industrial empregado na indústria do petróleo e em minerodutos devido ao sua excelente resistência mecânica. Os seus parâmetros provocam alterações metalúrgicas significativas no metal de solda. Neste trabalho foi estudado o aço microligado da classe API-5L-X70 em termos de microestrutura (metalografia e fratografia por microscopia óptica e eletrônica) e propriedades mecânicas (ensaio de tração a temperatura ambiente, dureza, dobramento e ensaio de impacto Charpy a – 20o C e a 0o C) após soldagem em arco submerso, nas regiões da zona fundida (ZF), zona termicamente afetada (ZTA) e metal de base (MB). O exame metalográfico apresentou microestrutura bandeada consistindo de ferrita poligonal, perlita e bainita, com pequeno tamanho de grão. Os resultados mostram o aumento da resistência mecânica influenciada pela presença de ferrita acicular. Análise fratografica apos ensaios mecânicos revelam comportamento dúctilfrágil.

Aug 16, 2017

By Faustino Roel

AMONG the problems confronting the mining engineer in Mexico in recent years, labor conflicts have come to occupy s prominent place. Each day they have become more serious and frequently have caused- the ruin of companies. It is therefore necessary for the engineer to understand the Federal Labor Law, the rights and obligations of companies and of their workmen, and the reasons for conflicts; to keep in mind the expense which may be caused companies; and to endeavor to avoid difficulties as far as possible. Our labor legislation is primarily to protect the workman and the constant tendency of the tribunals, including the Supreme Court of Justice, is to support the work- man in his demands against employer$, even at times granting him more than he asks, with no limit other than the economic capacity of the company to com-

Jan 1, 1937

By Luan Bezerra Silva

O presente trabalho pretende estudar o comportamento mecânico do cobre eletrolítico C11000 e da liga de cobre cromo C18200. Esses dois materiais são objetos de estudos da equipe técnica que está desenvolvendo a câmara de combustão do motor foguete propelente líquido L75. Atualmente, não há disponível na literatura informações sobre o comportamento mecânico desses materiais em altas temperaturas. A fim de suprir essa necessidade, foram realizados ensaios de tração a quente, no intervalo de temperatura de 27 a 500°C. Adicionalmente, foram realizados ensaios de dureza Vickers e metalografia para avaliar a capacidade do material em resistir mecanicamente em altas temperaturas. Os resultados obtidos demostraram que o cobre eletrolítico sofre amolecimento a partir de 400ºC e que o cobre cromo, apesar de apresentar elevada resistência mecânica quando comparado com o cobre eletrolítico C11000, é um material frágil.

Aug 16, 2017

By A. Y. Senchenko, Y. V. Kulikov

"Different methods aiming at specific energy calculation and design of AG/SAG circuits are used in mining. They include JK DWT/SMC test, SAGDesign test and CWi/RWi/BWi tests. The simplest methods with no secret equations and giving energy required for grinding in kWh/t were proposed by F.?. Bond and J.H. Starkey. D.J. Barratt proposed to use results of CWi/RWi/BWi tests for AG/SAG mill sizing. The present paper gives an alternative for forecast of specific AG/SAG energy. The principle is similar to the theory proposed earlier and consists in cumulative AG/SAG energy calculation using indices of rod and ball grinding (RWi+BWi) without impact crushing index (CWi). Then total energy is divided between two grinding stages using special formulas based on extensive statistical information. The forecast indices of AG/SAG and ball grinding are similar to the SAGDesign testing results. Hereinafter the predicted indices are used for mill sizing of the whole grinding circuit. The method considered in the paper enables prediction of AG/SAG energy based on the test results according to Bond method. The proposed method version was not widely published earlier. The aim of the work was to elaborate cost-effective, reliable and accessible way to determine specific AG/SAG energy. At this stage of method development, it is recommended to use it only for works at preliminary Geometallurgy stage (Scoping, Pre-Feasibility). At design stage the obtained data should be confirmed by appropriate testing using alternative JK DWT/SMC and SAGDesign methods.INTRODUCTIONAppropriate crushing and grinding testing is required to design efficient comminution circuits. It is obviously important to obtain accurate information about ore hardness properties since the main energy consumption at the plant is associated with comminution processes. Moreover, it is required to apply the processes that make it possible to minimize operating costs and efficiently use capacity of the installed equipment installed.When studying ore hardness properties, it is required to take into account that breakage of the material is performed using different equipment. That is why accurate selection of the equipment and the circuit calculation without relevant testworks is impossible. Ideally, the testworks should provide answers to the following questions: determination of ore hardness properties, determination of specific energy consumption for comminution as well as obtaining of sufficient amount of statistically significant results from the tests. The results from crushability and grindability testworks in the first place provide assessment of ore hardness properties and in addition correlate with throughput of the respective equipment. The data obtained can be used for modeling of comminution circuits at the stage of the technology development"

Jan 1, 2016

By Renan Celestino Silva Santos

O presente estudo trata da análise de falha de um cabo de aço utilizado em grua de construção civil. Para a análise da falha foram feitas metalografia, microdureza, análise dimensional e análise por microscopia eletrônica de varredura. Também foram feitos ensaios de tração, a fim de determinar a diminuição da resistência mecânica em decorrência de diminuição de área do cabo. A análise em campo detectou a presença de um dispositivo de acionamento do motor da grua que mantinha contato com o cabo e foi o responsável pela falha. Os resultados demonstraram que todos os fios estavam desgastados. Na maioria dos fios foi detectado aspecto de fratura plana frágil. A análise metalográfica e de microdureza não indicaram nenhum defeito metalúrgico nos cabos. Os resultados do ensaio de tração indicaram a diminuição significativa da resistência mecânica devido à redução de seção dos fios.

Aug 16, 2017

By A. Adu-Acheampong

Photogrammetry and laser scanning has been employed at a number of Newmont mine sites to mitigate risks associated with conventional structural mapping, determining the geometry of voids from old underground workings, and generating topography in areas of slope instability. Laser scanning has also been used to evaluate as-built pit slope configurations with respect to design assumptions, operational practices, and rock fall potential. Recently, remote sensing applications carried on an unmanned aerial vehicle (UAV) were used to generate base topography at some Newmont sites. UAV are generally more convenient and less expensive and can be utilized in areas where cloud cover prevents manned aerial photography missions. This paper discusses these applications, and provides commentary on their benefits and limitations based on recent experience.

Feb 27, 2013

As part of the Phase I study activity, a questionnaire was sent to a representative sampling of mining companies to obtain information on the uses, use conditions, personnel policies and other user concerns associated with front-end loaders. On-site visits to several of the mining companies were also parried out and the questionnaire was used during these visits as well. Five major areas were dealt with in the user questionnaire. These included: 1) Front-End Loader Critique - An open-ended form was employed to permit the mining companies to describe the particular things they liked and disliked about front-end loaders, in general, and/ or specific models in particular. 2) Usage - A form indicating the functions performed by front-end loaders and the numbers, makes and models of front-end loaders being used by mining companies. 3) Environment - A form where the user indicated the various types of conditions encountered in their use of front-end loaders. 4) Personnel - A form for describing factors pertaining to the qualifications of front-end loader operators. 5) Miscellaneous and Comments - A form permitting the user to comment on his feelings toward standardization of front-end loader operator stations.

Jan 1, 1973