Search Documents

By David L. Holt

It is well-established that hydrostatic pressure distribution is hardly achieved during uniaxial compaction of powders. All the previous investigations1-4 give consistent results and this variation is attributed to the die-wall friction. The conclusions are based on measurements of the density of very small portions of the compact. Although the analysis of the density or the strain distribution in the compact is very helpful in obtaining information about the stress distribution within a powder compact, it does not describe the problem from a more fundamental point of view. The densification in metal powder compacts takes place chiefly by plastic deformation (ignoring particle rearrangement) at the points of contact of the powder particles. The onset of yielding and subsequent growth of the contact areas (for spherical powders) take place fixed by a constant stress equal to three times the yield stress in tension or compression,5-7 assuming little or no work hardening. Therefore, by deforming spherical powders in the die and measuring the contact areas on each particle, the load at each contact point can be determined. In the present investigation, this was done by hot-pressing uniform spheres of lead, K-Monel, and sapphire. The details of the experiment have been described elsewhere.' The spheres were studied for the size and the number of contact points on each particle using a specially designed goniometer. It was found that the deformed faces that were approximately normal to the direction of pressing were about 2.2 times larger than those parallel to the direction of pressing. Fig. 1 shows the typical deformed sphere. A detailed study showed that the mean value of the contact areas on each sphere was within 5 pct for all the spheres in the die (ignoring those touching the die walls and the top and bottom of the die).' The spheres touching the die walls and the top and bottom of the die were found to have larger contact areas (8 to 10 pct) which indicates higher pressures in these regions of the compact and thus higher compact densities in these regions. These results show that density distribution calculated from such an experiment will give results consistent with the previous investigators. It is concluded, therefore, that the pressure distribution in the die is better understood by studying contact areas on each particle. 'R. Kamm, M. A. Steinberg, and J. Wulff: Trans. TMS-AIME, 1947, vol. 171, p. 439. 'Pol Duwez and Leo Zwell: I. Metals, 1949, vol. 1, p. 137. 'G. C. Kucynski and I. Zaplatynskyj: Trans. TMS-AIIME, 1956, vol. 206, p. 215. 'R. P. Seelig and J. Wulff: Trans. TMS-AIME, 1946, vol. 166, p. 492. 'H. Hencky: Z. Angew. Math. Mech., 1923, vol. 3, p. 241. "J. Ishlinsky: I. Appl. Math. Mech. USSR, 1944, vol. 8, p. 233. 'D. Tabor: Proc. Roy. Soc. (London), Ser. A, 1948, vol. 192, p. 247. 'Ashok K. Kakar and A. C. D. Chaklader: 1. Appl. Phys., 1967, vol. 38, p. 3223. Superplasticity in 60Zn-40Al David L. Holt THE occurrence of superplasticity in Al-Zn alloys is of interest because of its possible industrial exploitation.' The eutectoid composition (78Zn-22A1) has been the most extensively studied;'-= neck resistant flow and high strain rate sensitivity of flow stress (characteristic of superplasticity) are associated with a micron-size grain conferred on the alloy by an homo-genization and quench.5'6 Compositions away from the eutectoid have received comparatively little attention, especially from the viewpoint of relating the structural

Jan 1, 1969

By J. J. Bezuidenhout

The waste-heat boiler is used within the Sulphide flash smelting process as the main dust and energy recovery unit. The large volume of off-gas discharged from the flash smelter is at a very high temperature (1350°C) and contains a significant dust load that subjects the downstream waste-heat boiler to tough and demanding conditions. The boiler cavity is especially prone to dust accretions, fouling, and corrosion caused by accumulation of molten particles and precipitation of sulphuric acid. Computational fluid dynamics (CFD) is applied within a qualitative study to model the flow and heat transfer distribution throughout the waste-heat boiler. The commercial CFD package, Fluent 6.2.16, was applied to a modified waste-heat boiler (23 m ×11 m ×5.4 m) within the Outokumpu flash smelting process. This investigation focuses on the geometric modifications to the typical boiler design, which includes elevation of the ceiling, placement of flow-obstructing baffles and radiation plates parallel within the flow path. Also investigated were various boiler operating conditions such as the circulation of process off-gas, air leakage from the dust discharging hoppers and variation in inlet gas composition. The geometric modifications had the desired effect of increasing the volumetric utilization and therefore enhancing heat transfer between the boiler surface and the gas stream and dust segregation. Introducing circulated off-gas at a rate of 20 m/s and at a 45° angle to the front of the waste boiler further enhanced cooling while reducing the high impact of the furnace-uptake gas-stream on the boiler ceiling. The placement of radiation plates was found to be very effective in enhancing the heat transfer surface and distributing gas flow within the boiler. These results present recommendations towards an improved waste-heat boiler design. Keywords: flash smelting, waste-heat boiler, CFD simulation, off-gas cooling.

Jan 1, 2008

By J P. Clark

Industrial minerals contribute about 50% of the NZ$1.2 billion generated annually by the minerals industry in New Zealand. The value is supplemented by a further NZ$500 million of minerals imported to supply our vital agricultural and industrial activity. As globalisation of the world's economy precedes, sources of minerals are being processed by fewer companies giving an ever-increasing control over global markets. If only to protect its primary production New Zealand needs to aggressively develop its mineral resources. The successful development of a deposit requires identification of the preferred market. While low-value aggregates dominate New Zealand industrial mineral production it is more specialised minerals supplied to the manufacturing and industrial sectors that provide more value per tonne. Minerals that have highly desirable intrinsic properties, or through value-added processing provide desirable properties, have the ability to fill niche markets both locally and overseas. Research and development towards enhancement or creation of desirable mineral properties could benefit New Zealand with both increased mineral potential and export of technological information. But, it is nearly always the market not the resource that dictates the viability of an industrial mineral and, with the globalisation of industrial mineral markets resulting in fewer but larger companies, any supplier must be ready to explore niche markets in order to compete on a more global basis.

Jan 1, 2000

By Jeffrey L. Dean

Now in its twenty-fifth year, the ISEE has grown to more than 4000 members representing 75 countries. The Society and its 35 chapters in the US, Canada and Australia work to educate the public about our industry, provide forums for the exchange of explosives technology, serve as a repository of explosives information, offer expert help to governments, develop standardized methods and terminology, and promote research and education by, creating and conducting certificate and trainktg programs and encouraging the teaching of the safe and controlled use of commercial explosives.

Jan 1, 1998

By Guerold Sergeevitch Bobrovnitch

Amostras de polifurfural (FH) obtidas por catálise ácida foram termobaricamente tratadas em várias temperaturas e sob pressão de 6GPa em um dispositivo de alta pressão do tipo bigorna com concavidade central. Após o tratamento cada amostra foi submetida a análise por microscopia eletrônica de varredura. Os resultados indicam que a FH é um material grafitável e, possivelmente, poderá ser utilizado como matéria-prima para a execução do processo de síntese.

Aug 16, 2017

By Emilio Caballero

El presente texto señala la eficiencia del sistema mecanizado aplicado a las minas subterráneas en Canadá donde se obtuvo rendimientos y costos de producción que permitieron hacer un mejor uso de sus reservas. En ese sentido, se analiza la mecanización y se compara su eficiencia con la Compañía Minera Alianza. Para ello, se revisa el diseño de la mina, selección de equipo, plan de entrenamiento, mantenimiento del equipo y servicio, stock de repuestos, trabajadores en determinada área, supervisión a los equipos y el aspecto laboral.

Jan 1, 1982

By M. M. D. S. Vemba

Paper written on project work carried out in partial fulfilment of B.Sc. Eng (Mining Engineering) degree Engineering refers to the application of mathematics and other sciences to logically develop solutions to problems. However, in opencast mining, due to the randomness of operations, the use of mathematics is often neglected. Instead, practices that have proven successful elsewhere tend to apply. At the other end of the scale, mathematical models have been developed to identify and quantify all the operational parameters involved in the loading and haulage of ore. These are then used to optimize the operation. Optimization in this context, refers to the reduction of cost through effective utilization of the available time and resources. Considering these mathematical models, the loading and transport system at SMC (Catoca Mining Society) will be assessed with a view to its optimization. The discussion will be introduced by considering the mine background and other general information, which will highlight the main operational variables.

Jan 1, 2004

By J. Davies

This paper describes the successful management and construction of the 5.18 m (17 ft) diameter, segmentally lined, North Dorchester Bay CSO storage tunnel in Boston, MA. This 3,300 m (10,830 ft) long tunnel was mined through variable soft ground with only 6 m (20 ft) of cover, using an earth pressure balance tunnel boring machine. These extensive data collected from the projects unique automated and internet accessible geotechnical and TBM monitoring system, will be examined and used to explore the relationships between geological conditions, TBM operating parameters and measured settlements. The paper will also discuss the use of screw revolutions as an indicator of muck volume.

By Fernando Vital Silva

O processo de lingotamento contínuo consiste de uma série de etapas que promoverão a extração de calor de maneira controlada do aço líquido, com o objetivo de promover sua solidificação. Uma vez que a solidificação é considerada uma transformação de fase, regida essencialmente pela troca térmica, o enfoque do processo de lingotamento contínuo se encontra direcionado para o perfil térmico de resfriamento do aço desenvolvido ao longo dos veios da máquina. É extremamente importante para a qualidade final do tarugo que este processo de extração de calor ocorra a taxas controladas, de maneira contínua e uniforme em todas suas faces. Segregação, trincas e romboidade são alguns dos problemas de qualidade que podem ser originados devido a um controle não assertivo ou deficiência do sistema de refrigeração. Os tarugos lingotados do aço 1545-D, produzidos na máquina de lingotamento contínuo da Votorantim Siderurgia Barra Mansa, apresentavam com frequência trincas sub-superficiais nas quatro direções de resfriamento e a uma distância constante da superfície do tarugo. Através de equações de solidificação foi constatado que a profundidade em que as trincas se encontravam nos tarugos correspondia a um trecho da máquina no qual existia gap de refrigeração, provocando reaquecimento do material e o surgimento de trincas devido ao regime de contração/dilatação ao qual o mesmo estava submetido. Tais conclusões permitiram comprovar falha no projeto de refrigeração secundária da máquina.

Jul 30, 2018

By A. G. Spencer

"The horsepower required to drive large grinding mills has increased dramatically during the past ten years. Limitations on the amount of power which may be transmitted by a single gear and pinion have resulted in the application of multimotor drives, with consequent loadsharing problems. It has also sparked the development of some entirely new drive concepts. In addition, the severe demands made upon the electrical system during the acceleration period have required that the selection of motors and electrical system design be closely coordinated. Moreover, the installation of such large process units results in downtime being very costly. The equipment selected and the plant maintenance philosophy must therefore be such as to minimize the risk of unscheduled downtime."

Jan 1, 1972

By Arthur V. Corry

GOLD was discovered in Alder Gulch, Virginia. City, Mont., on May 26, 1863. In a short time some 6000 people flocked to the new discovery, and on the banks of Alder Gulch six settlements sprang into existence, the principal one, Virginia City, alone surviving. This town today has a population of 800, and is the county seat of Madison County. It is estimated that between forty and fifty million dollars in gold was produced up to 1904. Virginia City is situated at the mouth of Alder Creek where that stream leaves the narrow canyon that cuts the steep foothills flanking Old Baldy Mountain, elevation 9572 ft., 12 mi. south. Virginia City itself is 5700 ft. above sea level.

Jan 1, 1936

By Walther Rodolfo Ventura Gallardo

El presente texto señala un ejemplo de desembalse de relaves desarrollado en el campamento Comihuasa, perteneciente a la Compañía Minera Cautelosa S.A., donde se afectó las condiciones naturales de los ríos, población y actividades productivas. Por tal motivo, se ejecutó un plan de acción inmediato y de corto plazo que consiste en un estado de alerta de los establecimientos de salud, protección del ganado para evitar que beban agua de los ríos contaminados, inventario de animales afectados por falta de agua segura para su consumo, construcción de abrevaderos, abastecimiento de agua para ganado, recojo de relaves y suelos afectados, su disposición adecuada y segura, rehabilitación de suelos, recuperación de pastizales, repoblamiento de especies acuáticas en los ríos, supervisión del cumplimiento de las medidas de remediación, y recuperación de la calidad ambiental y sanitaria de los ríos.

Jul 1, 2014

By W. J. Errington

The Isasmelt process was developed at Mount Isa Mines Limited in Queensland, Australia in collaboration with CSIRO, the Australian Government research organisation. Originally developed for primary lead smelting, culminating in the construction of a 60,000 tonnes per annum lead smelter at Mount Isa, this technology now also provides a major part of the current 200,000 tonnes per annum copper smelting capacity at Mount Isa. A programme is now in place to expand copper production to 250,000 tonnes per annum. The technology has also been applied to secondary lead smelting at Britannia Refined Metals, a MIM subsidiary company, where a 30,000 tonnes per annum lead plant based on battery scrap feed has been operating since 1991. Mount Isa Mines Limited decided to license the technology in1988, and copper smelting plants utilising Isasmelt technology are now operated by Cyprus Miami Mining Corporation in the USA and by Sterlite Industries in India. In addition, the technology was adopted by AGIP for smelting copper/nickel concentrates in Australia. Union Miniere are currently constructing an Isasmelt furnace to smelt and convert copper-containing materials at their plant at Hoboken in Belgium. This paper discusses these developments and also some likely future developments which include the application of the technology for continuous copper and nickel converting and applications in the treatment of zinc-containing residues.

Jan 1, 1997

By Jeffrey D. Thatcher, Debra W. Struhsacker

With the burgeoning development of precious metals heap leach mining projects throughout the country regulatory agencies are beginning to take a closer look at the short-and long-term environmental consequences of heap leach mining. This increase in regulatory review is occurring on federal, state and local levels, and is affecting both large- and small-scale mining developments. Small-scale mining developments are receiving especially critical regulatory scrutiny because in the eyes of some regulatory agencies, small developers lack the credibility automatically accorded to major mining companies. This is due in part to a bad image of small miners based upon past environmental problems and permit violations caused by a few, small operators. The proponent of a small mining development thus faces special problems during the project permitting process, and must convince the regulatory authorities of his company's ability and commitment to plan, develop, and decommission a mining operation in compliance with environmental regulations. Not only must the small developer have a thorough understanding of the regulatory requirements affecting his project, he must also devote considerable effort to careful internal planning in order to produce a well organized approach to project permitting. The importance of proper planning cannot be overstated. Project planning is key to convincing the regulatory agencies that the small miner is capable of developing a viable project. More- over, the economics of a small mining project demand permit acquisition at modest cost and in a timely fashion. A well planned permitting effort will thus ensure that permits are received within budget and on schedule. This paper will review the federal, state, and local permitting requirements for heap leach projects, and the variability of these requirements from state to state. The environmental assessment process for projects developed on public lands, and the acquisition of zero- discharge water quality permits, air quality permits, and local special use permits as they apply to small mining developments will be discussed. The paper will conclude with a review of project decommissioning and cyanide neutralization requirements and their implications for small-scale heap leach projects.

Jan 1, 1987

By Christopher Mark

The first International Conference on Ground Control in Mining opened with the topic of pillar design. Two classic papers were presented, one by Bieniwski and the other by Wilson. Unfortunately, the two methods were so radically different from each other that it was nearly impossible to reconcile them. Adding to the confusion were the many other pillar strength formulas (such as the Salamon-Munro, the Holland-Gaddy, and the Obert-Duvall, just to name a few) that were also available. Little wonder that discussions of pillar design in those days often ended with anguished cries of ?but which formula is the right one?? The past 25 years have seen substantial progress in the science of coal pillar design. Indeed, one testament to the improvement is the relative scarcity of papers on the topic at recent Conferences. Two factors have been largely responsible for the progress that has been made. The first has been the collection of large data bases of actual case histories of pillar performance in a variety of settings, from shallow room-and-pillar mines through deep cover longwalls. These have made possible the development of empirical design procedures that are closely linked to real world experience. The second important factor is the development of sophisticated computer models that can accurately simulate pillar behavior and roof/pillar/floor interactions. Together, these two lines of research have led to a new understanding of pillar mechanics that identifies three modes of pillar failure: ? Sudden, massive collapse, accompanied by airblast, for slender pillars (width/height<4) ? Squeezing, or slow, non-violent failure, for most room and pillar applications (4<w/h<10) ? Entry failure or bumps for deep cover and longwall applications (w/h>10) It is particularly satisfying that the insights gained from numerical models broadly support those obtained from the empirical studies. While far less controversial than in the past, pillar design problems continue to arise. One recent example is pillar design for highwall mining. NIOSH has just released a software package, called ARMPS-HWM, which employs a number of modern pillar design concepts. Since highwall mining web pillars are long and slender, the greatest danger is that of a sudden collapse. ARMPS-HWM suggests two possible prevention strategies, one which concentrates on the SF of the webs, and the other which creates a ?pressure arch? using properly sized barrier pillars. The paper will close with a discussion of some current needs in coal pillar design, including: ? Updating older empirical methods, such as ALPS, where changes in technology (new types of roof support, more demanding ventilation requirements, faster retreat rates) may have made some of the original case histories obsolete. ? Methods for determining site-specific coal strengths, focusing on bedding plane strength and other factors that may effect confinement, as input for both empirical and numerical design. ? Improved methods for evaluating coal pillar performance for environmental issues, such as surface subsidence and hydrologic impacts, which consider such factors as depth, w/h ratio, water immersion/drainage, and time dependent seam strength.

Jan 1, 2006

By M. Kawahata

Methane sensors using principle of catalytic oxidation of methane are employed for determination of methane content in ambient air of coal mines. Certain foreign gases or vapors in the air poison the catalyst of the sensor effecting the sensor&apos;s response. After literature search of poison compounds of Pt and Pd oxidation catalyst, experimental studies of catalyst poison kinetics were made for three siloxane compounds, tributyl-phosphate, monobromotrifluoromethane, and hydrogen sulfide, selected as poison vapors. Concentration range of the poison vapors was varied in a range from 3000 to 0.1 ppb (v/v). Three siloxane vapors produced strong catalyst poison effect, followed by tributylphosphate, hydrogen sulfide and monobromotrifluoromethane for the high concentration level of the poison vapors. The poison effects are influenced significantly by concentration of the vapors. Threshold poison vapor concentrations where effect of the poison vapors on the sensor is minimal were determined experimentally. Experimental studies were made further for prevention method of catalyst poison by adsorption techniques. Use of activated carbon cloth inserted on the sensor&apos;s head prevented catalyst poisoning efficiently.

Jan 1, 1981

By Paul H. Lu

Methods and results of measuring three basic parameters for ground stability control, ground pressure, strata movement, and geomechanical properties of mine rock are presented in this paper. It is found that these parameters can be measured in situ by simple and practical techniques with nonsophisticated and inexpensive instruments. Specifically, a drillhole dilation technique employing a cylindrical hydraulic borehole pressure cell (CPC) was used to determine the modulus of rigidity. Premining ground pressures were determined by pressure convergence tests with a combination of one CPC and two pre-encapsulated flat hydraulic borehole pressure cells (BPC) installed in a single drillhole. Abutment pressures and pillar loading were monitored with BPC&apos;s. Differential strata movements and bed separations were measured with self-recording 10-anchor-point extensometers. Roof-to-floor convergence was measured with self-recording convergence meters. Some applications of these in-situ-determined parameters to mine design and ground stability control are also discussed.

Jan 1, 1984

By Y. Nakata, K. Nagata

Plasma is partially ionized gas composed of ions, electrons and activated elements at high temperature. Some flying ash from incinerated municipal waste is melted to become glass by a transfer-type arc plasma furnace. As the glass is ionic silicate, when an electric current passes through anode to cathode, ions in molten slag electrochemically react with electron in plasma at the surface of molten slag. In case of molten Na2O-SiO2, sodium ions in the molten slag carry electric current and SiO2are reduced to evaporate as SiO gas by electron in plasma. The cases of Ag+in NaNO3-KNO3molten salt and Fe2+in FeO-SiO2slag were examined. The amount of cathodic reaction is larger than that of anodic reaction and not apparently according to the Faraday?s law on the electrochemical reactions.

Jan 1, 2004

By K J. Thompson

This paper describes the work which has been undertaken at the Ohai coalfields in Southland to restore overburden heaps during past opencast mining operations, and procedures which have been adopted to ensure that restoration is achieved concurrent with present opencast mining activities. The system implemented for the treatment of wastewater from opencast mining operati6ns is also described.

Jan 1, 1981

By B Rosemberg, F Lemos, A J. B Dutra

The chemistry of cyanide solutions is complex, this complexity being responsible for the ability to act as complex-forming agents in metal dissolution processes, among them gold and silver. Such ionic species are used in hydrometallurgical processes, in particular in gold extraction and electro-plating. Due to the high toxicity of cyanide, the discard of effluent from processes and/or industries demands rigorous treatment so as to minimise its concentration. Among the conventional chemical treatment of such effluents one can mention SO2/air; biological degradation; oxidation by using hydrogen peroxide; oxidation by sodium hypochlorite, etc. However, the electrolytic recycling process is also promising for cyanide recovery and offers the possibility of recycling it to the aforementioned industrial processes. Such a process does not use additional chemicals but enables direct re-utilisation to the main process aiming at adjusting the cyanide concentration.

Jan 1, 2002