Search Documents

By M. du Plessis

This paper describes the evaluation of a limit equilibrium model to simulate the behaviour of crush pillars in platinum mines. An analytical model was derived to calculate the residual average pillar stress (APS) values of the crush pillars. The values predicted by this model were compared to the numerical values obtained from TEXAN simulations. In general, the limit equilibrium model appears to be very attractive for simulating pillar failure as the gradual crushing of the outside of the pillar and the transfer of stress to the intact core can be replicated. The value of the TEXAN crush pillar model was further demonstrated by simulating an idealized layout with crush pillars between two adjacent panels. The simulations illustrated that oversized pillars will not crush close to the face and this may lead to seismic failure in the back area. An important finding of the study is that closure measurements may prove to be a very valuable diagnostic measure in crush pillars layouts. Distinct differences in magnitudes of closure were simulated for a scenario where the pillars crush as expected, compared to the scenario where an oversized pillar is left. Experimental closure data collected in a crush pillar stope provided further evidence regarding the value of closure measurements in these layouts.

Jan 1, 2011

By Thornton L. Neathery

Vertical magnetic surveys have been made over about 3, 150 miles of the crystalline area of east-central Alabama. A contour map (100-gamma interval) showing regional magnetic anomalies has been prepared (scale 1:250,000) from data points located at quarter-mile intervals on all public roads. Small one- and two-station anomalies were eliminated, leaving only areally extensive anomaly features associated with regional geology. The regional gradient was "filtered" from the basic data and the resulting magnetic configuration compared to the regional geology. Regional lines of vertical magnetic intensity trend northeast and follow the structural framework of the area. Correlations can be made between a large number of geologic and magnetic features. The strongest regional anomalies are associated with the Goat Rock, Bartletts Ferry, Towaliga, and Brevard fault structures. The Inner Piedmont area is characterized by a broad regional high. The magnetic values of the northern Alabama Piedmont grades gently northwestward, disrupted occasionally by elongate highs and lows associated with amphibolites or granites. Scattered throughout the Piedmont are anomalous areas of high magnetic intensity; some are related to magnetic-bearing rocks, and some Indicate possible mineralization. Most of the anomalies have not been evaluated,

Jan 1, 1972

By C. C. Clark, P. W. Patton, B. M. Stewart

Handling materials in underground mines continues to be a major safety problem. To help reduce materials-handling injuries, researchers at the Spokane Research Laboratory of the National Institute for Occupational Safety and Health are investigating those materials-handling tasks in underground mines that appear to generate a high number of injuries. Data from the Mine Safety and Health Administration for the years 1989-1999 were studied to find out if there were any trends in materials-handling accidents and if so, to determine what tasks were involved and the sources of injuries. Several underground coal and metal mines were visited to document innovative materials-handling technologies. Considerations for safety training and mechanization needs for continued reduction in materials-handling injuries are described.

Jan 1, 2002

By Williams K. C

This paper presents a brief account of the plant which has been developed at Port Pirie to recover, by vacuum distillation, the greater part of the zinc content of desilverized lead. The present plant is an experimental unit, which is run in conjunction with the normal refinery practice, but can be cut out of the circuit. It will shortly be dismantled and duplicate units will be built on the sites chosen for the final plant installation.The unit described here has treated flows of 16 to 37 tons per hour of desilverized lead, to recover 90 to 95 per cent of the zinc contained in it. It is not intended here to detail all aspects of the vacuum dezincing operation, nor the developments which precededthe adoption of this design. The essential features of the present plant will be described and, where these are peculiar to the present experimental location, the intended alteration for the final plant will also be mentioned. OUTLINE OF PLANT AND PROCESSLead issues from the continuous desilverizing kettle at about 350° C. containing about 0·57 per cent Zn. It is conveyed by a tiled launder to the preheater, where it is heated to 580-620° C.Hot lead from the preheater enters the vacuum vessel via a barometric leg. From a reservoir holding about 19 tons of lead it falls by gravity in a thin film exposed to high vacuum (20-50 microns)3 and leaves the vessel via a barometric leg, entering the lead pot. The lead leaves this pot at 540-560° C., containing 0·03 to 0·06 per cent Zn, which is removed, together with residual antimony of 0.02 to 0·06 per cent, by a separate final refining process.

Jan 1, 1956

By R. Larry Grayson, Joel R. Warneke

The mining industry has searched for a message that will resonate with the public while focusing on the industry’s positive contributions to society. So far, environmental groups remain unconvinced and the public is still largely uninformed. In the authors’ opinion, a number of recent events and experiences have converged to help shape a more effective public communication on mining’s important role. This article presents a perspective on coal’s role in sustaining society by anchoring the message in a transparent way, including a material flow analysis, that links coal’s impacts across a range of social and environmental aspects. Past and continuing image problems In her 1994 paper, Nancy Bingham, with Caterpillar, outlined what the public thought about mining. Based on extensive interviews, the following results were found: • The public believed mining harms the environment. • The public believed mining harms people in nearby communities. • The public believed mining exploits workers. • The public believed mining has little personal benefit to the individual.

Jan 1, 2006

By Mohamed A. Younis, Paul J. Headland, Paul H. Madsen, Vojtech Gall

INTRODUCTION A 100 ft long, 20 ft high and 18 ft wide NATM tunnel was excavated through grouted clean sands beneath a busy city street, including a variety of existing utility lines. The new tunnel associated with a hospital expansion will serve as a pedestrian tunnel connecting a parking structure with a new hospital facility. Tunnel construction started on December 15, 2005 when drilling for the grouting program started and was completed on May 26, 2006 when the tunnel final lining was completed. The tunnel was constructed by Kiewit Construction Company as a tunnel subcontractor to The Christman Company who is constructing the hospital facility for Spectrum Health in Grand Rapids, Michigan. URS was the project designer. GallZeidler Consultants, LLC were the contractor’s NATM consultant. PROJECT DESCRIPTION The Michigan Street Pedestrian Tunnel is a component of the Michigan Street Development located along the north side of Michigan Street NE between Coit Avenue NE and North Division Avenue in the downtown area of the Grand Rapids, Michigan. The Michigan Street Development includes a parking deck and four new towers to be constructed over the proposed parking deck. The tower planned furthest east is being developed by Spectrum Health as the Lemmen-Holton Cancer Pavillion. The purpose of the pedestrian tunnel is to connect the proposed Lemmen-Holton Cancer Pavillion with the future Spectrum building to be located on the south side of Michigan Street NE. The southern end of the tunnel was constructed with a bulkhead until the future Spectrum building is constructed at which time interconnection will be required. The tunnel site plan and profile are shown in Figure 1, Site Plan, and Figure 2, Tunnel Profile. Several challenges were faced during the design and construction of the Michigan Street Pedestrian Tunnel. These challenges included compressed design and construction schedule, maintenance of traffic and protection of old underground utilities. The tunnel was being constructed as part of the Michigan Street Development and coordination with other concurrent construction activities was required. The tunnel was constructed within a specified window of time to allow other associated construction activities to take place without compromising the overall project schedule. The design started in June 2005 and construction was completed by June 2006.

Jan 1, 2007

Judicious placement of a range of geotechnical instruments was employed at the Tasmania gold mine, Beaconsfield, Tasmania, as a key strategy in the monitoring of rock mass conditions over the past four years. The range of instruments employed included vibrating wire stress-meters and hollow inclusion cells to monitor changing stress conditions, resistance wire and multipoint borehole extensometers to monitor the impact of stress changes on the integrity of the rock mass, and instrumented cable bolts and threadbar bolts to monitor the static and dynamic impact of rock mass changes on the installed ground control system. Initially the monitoring was of a qualitative nature, monitoring change from the time of installation. The value of the output was considerable when considered in relation to the ongoing seismic record which was also being monitored. It was clear from the seismic record and the monitoring results that stope blasting was the primary trigger for changing rock mass conditions. However, it was unclear how well observed behaviour was reflecting conditions anticipated by elastic numerical modelling. The latter had predicted significant stress increase in the near field of man-access footwall development. Qualitative monitoring and visual inspection did not support the modelling prediction, and this led to a program of quantitative measurement being undertaken. Measurement of the absolute stress condition in the backs of footwall development immediately adjacent to monitoring hollow inclusion cells provided the benchmark for tracking quantitative stress change. The program provided insight into the evolution of principal stress field magnitude and orientation in relation to rock mass change observed with extensometers and instrumented ground control elements, as well as providing a degree of calibration between the elastic numerical modelling and the virgin stress field. Calibrated monitoring data has also provided a useful benchmark for finite element modelling which is to be used for future mine-wide design.

Nov 25, 2010

By Alain E. Holeyman

After scoping out the objectives of this general report, the report reviews the three assigned main themes addressed by the papers submitted to the session: pile monitoring, testing, and data processing. It focuses on later developments and on issues requiring clarification, thereby identifying topics for potential discussion. Pile Monitoring does not bring much novelty, except for the integration of IT on construction sites. As far as testing, new developments focus on internal pile loading procedures while more confidence is being gained with dynamic and kinematic load tests. Significant advances are noted in the interpretation of data, where variability of results are coped with, loading rate effects are being better addressed, and more routine use of Finite element analyses are observed. Several many older problems remain while new issues emerge from more recent technologies and approaches.

Jan 1, 2006

By Tom A. Armour

Different variations of soil nailing techniques have been used in the United States since the late 1970's. Such techniques owe their origins to French developments, which began in the early 1970's as a spin-off from European tunneling excavation support practice. The growing demands of urban infrastructure development and rehabilitation and environmental protection have created an active and expanding soil nailing market demand for earth retention and slope stabilization in the United States since its early developmental years. There is a clear need for a fundamental review of the large number of soil nailing techniques that are currently being used in the United States. Following a brief summary tracing the historical development of soil nailing and a generic classification of applications, this paper provides a review of the different recent advances in the design and construction of soil nailed systems. Discussion topics include nail design advances, permanent "top-down", structure support/underpinning, alternative face stability measures, composite systems, hollow bar and fiberglass nails and architectural reinforced concrete/shotcrete facings. Case histories will be presented to illustrate each of these advances.

Jan 1, 2003

By Richard S. Dennis

Acid recovery employs ion exchange (I-X) resin as separation media for inorganic acids from dissolved metallic salts by physical adsorption and without the use of chemicals. This technology has been used for years on spent etching and plating liquors to recover acid for reuse in the bath and to reduce waste acid neutralization costs. It is also used for electrolyte treatment to facilitate valuable metal recovery via acidity reduction. TETRA's ccrxr'" I-X contactor has been used successfully for acid separation from its metallic salt counterpart in a simple, continuous operating mode using strong base anion resins. Efficient separation is enhanced by acid reconcentration to nearly its original strength or as high as 14-20%. Continuous treatment also recovers heat to the tankhouse or bath and improves metal quality due to consistent acid quality. Conventional fixed bed ion exchange (I-X) systems are impractical for acid recovery because of complex control design and large resin inventories needed to process very low liquid-to-resin treatment ratios associated with strong acid concentrations.

Jan 1, 1996

By McNicol M. D

Petroleum exploration in onshore Gippsland was directed in the 1950s and 1960s towards plays in the basal Latrobe and Strzelecki Groups, but these became forgotten in the 1970s with the Latrobe play discoveries offshore. The principal explorationists of the time were Woodside Oil and Arco Ltd, who then departed the scene after drilling some 18 wells without major success. In the late-1980s successful hydrocarbon finds in equivalent age Otway Group sediments in the Otway Basin were made and in early 1990 Tyers Petroleum began investigations into Strzelecki Group prospects as applied to the onshore Gippsland Basin. Some 18 anticlines have been mapped, based on shallower coal exploration drilling in the Latrobe Group, which from seismic and gravity evidence are believed to unconformably overlie similar anticlinal structures in the underlying Strzelecki Group. Strzelecki targets of interest within drilling depth are the basal Tyers Conglomerate/Rintouls Creek Sandstone Formations which outcrop in the north of the Latrobe Valley and are analogous to the Pretty Hill Sandstone in the Otway Basin. In addition, intra-Strzelecki Group targets similar to Heathfield and Windermere Sandstone Members are also considered to be present. Good source rocks are abundant including coal seams and carbonaceous sediments of Neocomian and Jurassic age, which lie within the oil window. Seal is provided by the overlying Aptian-Albian aged volcanogenic sediments. The Tyers/Rintouls sandstones - a target in the Woodside/Arco wells, with two exceptions, were not reached. Encouraging intra-Strzelecki shows were reported in many of the wells. Basal and intra-Strzelecki porous quartzose sandstones remain one of the few untested plays left in the Gippsland Basin and, in the onshore, merit extra attention as they he within the oil window at economically drillable depths.

Jan 1, 1992

By D. Harrington

"FOREWORDVirtually all government agencies undertook many additional responsibilities during the period immediately preceding World War II; these responsibilities increased vastly in importance and scope after the actual declaration of war following the attack on Pearl Harbor. The Bureau of Mines was one of the agencies thus affected, and it was called upon to perform many duties foreign to its normal peacetime activities.The Health and Safety Division of the Bureau of Mines, at that time designated the Health and Safety Branch, was given several important and difficult duties and responsibilities of an unusual nature because of the war while of necessity-continuing its normal functions of assisting the mineral industries in the preservation of life and health and the protection of property, this being of especial importance in wartime because of the pre-eminent importance of having maximum output of essentially all types of mineral products. Some of these additional functions were given to the Health and Safety Division because the organization of the Division, with its field set-up dividing the Nation into districts with competent, experienced personnel in charge of its work, provided the nucleus of personnel and procedure through which rapid and smooth expanded functioning was feasible.In addition to the responsibilities directly attributable to definite war activities, such as the administration of the wartime Federal. Explosives Act and the Mineral Production Security Branch a new branch (then designated division) was formed to investigate coal-mine health and safety problems after the enactment of the Federal Coal-Mine Inspections and Investigations Act, which became a law on May 7, 1941, but which actually began to function actively after the declaration of war in December 1941.The purpose of this publication is to provide a brief historical record of the activities of the Health and Safety Division as a whole and of its individual branches during the war. The detailed record has been filed in the Archives Building, Washington, D. C."

Jan 1, 1949

For small particles of niekel flotation eoncentrate (av. size 50 pm) the predominant heat transfer mechanism under suspension smelting conditions, prior to ignition, is conduction from the gas and not radiation from nearby hot bodies. Results of laboratory tests using gas temperatures 380-700°C and furnace wall temperatures 380-1100°C were in accord with heat transfer theory. In practieal flash smelters earlier ignition, and hence better utilization of the space in the shaft, would result from introduetion at the top of the shaft of gases hotter than the ignition temperature of 500-600°C.

Jan 1, 1979

By C. L. Popp

The scope is to address issues confronted by parties in the mining industry such as: Mine planners, survey and engineering departments, field teams and subcontractors. Describing approaches and best practices for assembling a project team to identify and create modeling requirements and to implement beneficial results. 3D Machine Control and Guidance tools continue to reduce project risk and attract quality resources with skill sets new to the earthmoving industry. These tools increase production, reduce rework and help with government permitting.

May 1, 2013

By H. William Zeller, T. E. Westpha1

The U.S. Bureau of Mimes evaluated the effects of two iron-based fuel additives on diesel particulate matter (DPM) emissions. The 5.6-L, six-cylinder test engine is typical of engines used in underground mines. One additive, ferrous picrate, did not measurably affect exhaust emissions. This report is mainly about a ferrocene-based additive that reduced DPM between 4 and 45 pct, depending on engine operating conditions. The report concludes that the DPM reductions were caused by the catalytic oxidation properties of a ferric oxide coating that developed inside the engine's combustion chamber. The ferric oxide coating also decreased gas-phase hydrocarbons and O, but it increased CO, and NO,. The increase in NO,, of about 12 pct, is considered the only adverse effect of the ferrocene-based fuel additive. The results suggest that the effectiveness of ferrocene was partially offset by increased sulfates because of the high-sulfur fuel used. Recommendations for continuing fuel additive research are presented.

Jan 1, 1992

By William J. Neely

Augercast piles are formed by drilling a continuous-flight auger into the ground and, on reaching the required depth, sand-cement grout or concrete is pumped down the hollow stem as the auger is withdrawn. The sides of the hole are supported at all times by the soil-filled auger, eliminating the need for temporary casing or bentonite slurry. The augercast piling method is fast and economical; there is no vibration, very little noise and, if executed properly, no ground displacements during installation. The method is well suited to sands which are easy to drill and are readily transported up the auger. Relatively little attention has been given to augercast piles in the literature which might be part of the reason for the considerable variations in local practice, building code requirements and design methods. The purpose of this paper is to discuss some of the features of augercast pile installation that are known to influence both the structural and geotechnical capacity of the pile, to evaluate several empirical design methods and to look at some important aspects of quality control of augercast pile installation.

Jan 1, 1990

THE furnace described in this paper was installed and has been used by the writer for the melting of rich gold-bearing material, and has given complete satisfaction. It may, therefore, prove of interest to other metallurgists who are faced with a similarproblem. A furnace of this type should be most suitable for the reduction of "cyanide preeipitate," "charcoal ash," "anode sludge," &c. formerly the melting was done in fire-clay crucibles, using coke or crude oil as fuel, but this method is costly, slow, and unsatisfactory. A small water-jacketed blastfurnace was also tried on this material after briquetting it, but was discarded in favour of the electric furnace. The furnace may be described as a simple form of the Heroult resistance furnace, with an adjustable upper electrode and a fixed bottom electrode. This is in accordanee with Stansfield's classification of electric furnaces. The heating is mostly due to the resistance offered the current by the molten slag. The melting chamber consists of a steel drum 14 in. in diameter and 21 in. high, and is lined with silica bricks specially made to fit the shell. The internal diameter is G in. The bricks contain 92 % silica, are made from calcined quartzite bonded with fireclay, and are similar in composition to those used for lining steel converters. They are set in a mixture of finely-ground quartzite and clay, and well dried out. The shell is bolted to a steel plate, which forms the decking of a truck running on rails, so that the furnace can be moved under ahood for carrying off the fumes. A cast-iron slag spout is bolted to the shell below the tapping hole, which is 4 in. from the bottom of the shell. Opposite this another hole 1 in. in diameter is drilled through the shell and lining for the passage of the lower...

Jan 1, 1918

In the early stages of opening up a mine, when there is some uncertainty as to its future career, necessitating caution in laying out works of a permanent character, the want is often felt of an assay furnace, easily built and easy of transportation, should the" mine " prove to be " no mine." Again, cases occur in which parties buy the right to treat comparatively small heaps of tailings, and then shift their plant to other localities. Under these circumstances it is necessary to restrict the plant to the barest necessaries, to suit, so to speak, the nomadic character of the work.An assay furnace that is really portable, easily transported, erected, taken down, of little weight, always ready for action on short notice, is indeed in these cases a desideratum which has long been wished for. The gasoline furnaces introduced intothe Australian market some time since practically fulfil these conditions; but they have the fatal drawback of being dependent on a constant supply of the liquid fuel, gasoline, which is seldom, if ever, obtainable locally in' any wayback mining township...

Jan 1, 1904

By Yates C, Gillie E. W, Finucane K. J

During the year 1940 a complete investigation was made of the whole of the stoping operations throughout the Great Boulder Mine and, as a result, it was decided to convert some of the existing shrinkage stopes into cut-and-fill stopes, and also to mine many of the more recently developed ore blocks by the latter method. The necessity for filling was due primarily to the structure of the ore blocks, the character of the walls and possible excessive dilution, but was influenced also by the grade of the ore-block and by the fact that cleaner mining can be carried out by cut-and-fill stoping.The comparatively few cut-and-fill stopes in operation prior to 1940 had been filled mainly with waste rock from development work, but as the amount of this material available, or likely to become available, would have been wholly inadequate for future operations, it was proposed to construct a system of passes to supply filling material from the surface.Owing to the distribution of the stopes, no central pass or system of passes could be devised which would service all the stopes satisfactorily.However, work was commenced on two passes, one designed to service the cut-and-fill stopes in the Eastern Section of the mine, and another to service those in the Western Section. It was realised that these passes could serve only a small proportion of the total number of Stopes (Figs. 1 and 2). During the progress of this work experiments were undertaken to test the possibility of using filtered tailings underground as an adjunct to the above scheme, but for various reasons these were only partially completed.Early in 1942 it was suggested by the Mill Superintendent that an attempt be made to fill with wet classified flotation tailings as practised at Mt. Lyell in Tasmania and at the Triton Mine at Reedy, West Australia. For the purpose of testing this, an experimental stope was prepared on the 309-ft. level, "X" Lode. This was 100 feet long and averaged 4 feet in width. Water-tight rearings were built at each end of the stope and waste rock fill was spread to a height of 6 to 8 feet above the timber. Used filter cloths were laid on top of the fill and brought a few feet, up the walls of the stope. A two-inch victaulic drainage line was then placed in position, the end passing through a hole in one of the bearings and thence to a sump. In the central portion of the stope two vertical pipes were brought up from this line. These were bored with one-inch holes staggered on opposite sides of the pipe, the vertical interval between each hole being one inch. The holes were then stopped with...

Jan 1, 1945

The rapid advance in the adaptation of scientific knowledge to the treatment of ores, resulting in improved chemical and metallurgical processes, has enormously increased the possibility of working lodes profitably, which a few years ago were passed over as unpayable. By the discovery of chlorination, and later of "Cyanidation," by the highly improved methods of concentration, and by the rapid advance in our knowledge of smelting (for which we are greatly indebted to Americanmetallurgists), and by the gradual replacement of scientifing principles and enlightened management, for rule-of-thumb methods formerly in vogue, many large low grade bodies have been opened, and are now paying dividends, which were,twenty years ago, looked upon as hopelessly unpayable. It has been more especially in these large low grade ore bodies, that modern methods have been benefical; for small lodes must be rich to pay at all, as they cannot be worked on the same gigantic scale, but even in these a percentage of metal is saved which formerly was absolutely lost.To make these large deposits remunerative it is, however necessary to try and find the point of greatest economic advantage, to handle the ore in vast quantities, to erect huge plats to treat it, to substitute automatic appliances for hand labour as far as possible, and to combine several processes supplementary to one another, so that ore which is not amenable to one process, shall be saved, by another; and by doing...

Jan 1, 1901