Search Documents

By Lewis Stansfield

A rotary displacement method was used to install permanent steel casings for bored piles through an asbestos tip. This method was chosen in preference to alternative driven systems because it was quieter and more versatile if obstructions were encountered. New equipment was designed and made specifically for the project, and stringent health and safety regulations had to be observed.

Jan 1, 2000

By James A. Madonna

Information gathered while studying geological parameters that govern fine gold deposition in the a1luvial environment can be applied to the technological development and selection of fine gold recovery systems. It is recognized that substantial gold losses occur in the minus 1.5 mn (minus 12 mesh) fraction using conventional sluicing systems. Within the past two decades much attention has been given the design and efficiency of these thick bed concentrators. Studies and comparisons drew information from several foreign and domestic placer operations. These studies concentrated on: 1) the physical and chemical properties of alluvial gold 2) the parameters that control fine gold deposition 3) the geometrical form, components and general working structure of conventional sluicing systems 4) the physical properties which contribute to the overall efficiency of a sluice system 5) the comparison of three major styles of conventional sluicing systems. A dramatic improvement regarding fine gold recovery and water quality was observed when using modern multiple-channel sluicing systems in place of conventional single-channel sluicing systems.

Jan 1, 1988

By A. T. Iannacchione

Underground stone mining represents an emerging sector for the U.S. mining industry. As this expansion takes mines under deeper cover and as more efficient mining methods are utilized, adequate stone pillar design methods will become more important. It is the purpose of this paper to examine current design practices and to discuss issues for safe mine layouts so that a rational first approach towards balancing the demands for increased production can be weighed against increased risk to worker safety from rib instabilities and pillar failures. Seventy-two stone mine pillar designs were examined. Pillars with width-to- height ratios below 1.5 and subjected to excessive stress levels appear more likely to fail. When width-to- height ratios fall below 1 .0, defects in the pillars, such as through-going discontinuities, can have a significant influence on stability. Discontinuity persistence, dip, material properties, and orientation are important factors controlling pillar strength. The influence of discontinuity dip, a characteristic easily identified in the field, was examined so that its presence could be accounted for in developing generalized guidelines for pillar design.

Jan 1, 1999

By Priscila Alves da Silva Machado

A busca por pesquisas que provem soluções e inovações que utilizam parte de tais resíduos vem ganhando grande destaque. O poli (tereftalato de etileno) é um polímero termoplástico, e é o material base para produção de embalagens plásticas que são comercializadas mundialmente. Sabe-se que é de grande volume os resíduos sólidos provenientes de tais embalagens plásticas. Com o objetivo de solucionar um problema ambiental e verificar a viabilidade técnica, foram fabricados em proporções de 0%, 5%, 10% e 15% m/m, materiais compósitos de base cimentícias reforçados com fibras de poli (tereftalato de etileno) provenientes de resíduos de garrafas plásticas (PET), posteriormente amostras passaram por caracterizações mecânicas. Destacou-se um aumento das resistências a compressão axial e diametral do material produzido com fabricação de adição de poli(tereftalato de etileno). Tais resultados referente a resistência foram positivos, propondo assim a utilização do polímero na composição de novos compósitos.

Oct 30, 2017

The Upper Waimangaroa mining permit is part of the Buller Coalfield and lies on the eastern side of the Stockton-Denniston Plateau. The mining permit area is estimated to contain a total in-ground coal resource of 58 million tonnes, contained within 13 separate coal resource .blocks. The coal is Bituminous High Volatile B rank with export potential as semi soft coking or thermal coal. The Northern Opencast mine is the first mine proposed for Upper Waimangaroa and consists of the three resource blocks at the northern end of the permit area. The highwall of the mine will cut into the Mt William Range resulting in overburden cover of up to 150 metres in some areas. The ability to rehabilitate the area after mining was a major consideration in the design of the mine. The Northern Opencast area has been geologically mapped, extensively drilled and effectively modelled using Vulcan software. Three distinct coal seams are present and the mineable in situ resource is estimated at 8.7 million tonnes of which approximately 7.1 million tonnes is likely to be recoverable. It is proposed that this resource will be mined using opencast methods and the void will be backfilled with overburden. The life of the mine is at this stage estimated at 19 years based on an annual production of 500,000 tonnes at 1.8% sulphur and the Upper Waimangaroacoal will be blended with low sulphur coal from the Greymouth Coalfield to meet export specifications. The Northern Opencast area contains a range of native flora and fauna and physical features which make it an environmentally significant area. Mining will totally modify the area, thus an effective rehabilitation scheme is an integral part of the mine plan. Various rehabilitation methods will be used, and wherever possible, the backfilled areas will be rehabilitated so as to resemble the original area as closely as possible.

Jan 1, 1998

Much attention in controlling blast vibrations has been centred on the probability of causing damage to structures in the area adjacent to where blasting is carried out. In most cases these structures are residential properties and the effect of the vibrations on the occupiers has not been studied to any great extent. This paper looks at the sources of disturbance caused by blasting and their psychological effect. A comparison of ground vibration levels for compliance is examined within the framework of structural and human response.

Jan 1, 1998

By M. England

Keywords: Bi-directional tests, Osterberg cell, O-cell®, static load tests, Timeset® Static load testing, where loads are applied vertically to the top of the pile and often referred to as 'top down testing', has been used for many years and has become a 'standard' test for the world of foundation engineering. The method, although well developed, cannot be used under certain circumstances, magnitude of load being a particular issue. There is a finite limit to the load capacity that can be applied with either kentledge, the use of reaction piles or anchors, and as the loads increase, the costs escalate dramatically. A novel test method seeks to overcome all the associated problems of large scale and restrictive area "top down testing", utilising static load testing techniques. The method requires the foundation element to be divided into two or more sections and these can be loaded axially as required using a portion of the foundation element as a reaction. This paper presents some recent applications and developments in the use and application of the bi-directional testing technique using the Osterberg Cell or O-cell® and outlines some of the many advantages of the system. Recent bi-directional test loads applied to bored piles have mobilised capacities of 279 MN and with flight auger piles up to 25 MN.

Jan 1, 2006

By Eric Konigsmann, Doug Spence, Scott Jones

"The Williams Gold Mine is located in the Hemlo camp of Northwestern Ontario and is one of Canada’s largest gold producers with annual gold production of 400,000 ounces. The operation is owned and operated as a 50:50 joint venture between Teck Cominco Limited and Barrick Gold Corporation.In July 2002, the decision was made to introduce paste backfill produced from mill tailings as the primary backfilling method in the mine and to decommission the existing cemented rock fill system. This required a fast track design to be completed for both a surface paste backfill plant and an underground paste distribution system followed by an intensive construction phase through the fall and winter of 2002/2003. The paste system was commissioned on schedule in late April 2003 and was in full production within 4 weeks of the initial start up. Overall, the project duration was only 42 weeks from initial project release to commissioning and it was completed $2 million under the budget of $14 million.This paper presents an overview of the lab testwork and process flowsheet design, process control methodology and describes the construction and commissioning phases of the project. Preliminary paste plant performance and operating cost data is also presented.IntroductionThe Williams Gold Mine is located in Northwestern Ontario adjacent to the Trans Canada Highway in the Hemlo Gold Camp as shown in figure 1. The mine currently produces approximately 400,000 ounces of gold annually and is owned and operated as a 50:50 joint venture between Teck Cominco and Barrick.The deposit was discovered as part of the Hemlo gold discovery in 1981 which led to the development of three mining operations within a 2 kilometre radius. The neighboring operations are the Golden Giant Mine, currently owned and operated by Newmont Gold, and the David Bell Mine, currently owned and operated by the same joint venture which is running Williams. David Bell ore is blended and milled in the Williams concentrator."

Jan 1, 2004

?? Intro ?? Mass blast principle ?? LaRonde evolution toward mass blast ?? Overview ?? Mining method ?? Longitudinal ?? LaRonde evolution (2002 to today) ?? Drill and blast design ?? Consumptions and statistics ?? Mucking strategies ?? Case study ?? Examples ?? Conclusion ?? As underground mines extends to greater depths, few questions must be asked: ?? How to: keep operations safe eep operation effective reduce the cost maintain and control the dilution ?? Geomechanic method and practices; significant advances have been observed in the field of: ?? ground support ?? mining sequencing ?? Drilling and blasting; research and development has been less extensive, probably due to the following characteristics: ?? Drill and blast are mainly production-oriented ?? Drilling and blasting are more oriented toward productivity ?? Technology relies heavily on suppliers ?? Highly stressed ground conditions ?? generally help the explosives to break the rock for fragmentation ?? intensify over-breaks or blast-induced

Feb 1, 2008

By William M. Gleason

The war in Vietnam stretched into another decade, an American President was at the brink of impeachment, the earth was given its own day, twin tower monuments of American ingenuity were completed in New York and would stand high above the Manhattan skyline for 31 years. Inflation, oil shortages, low commodity prices and America’s 200th birthday were part of the decade — it was the 1970s. For the mining industry, the demands of the decade would be high and the challenges would be significant. Because of the many challenges that lined up in front of it, the mining industry was forced to work smarter and more efficiently. The industry also expanded its borders in search of new resources and struggled along with the rest of the world through a fuel crisis, inflation and a recession.

Jan 1, 2007

By J. H. Morris, G. M. Steed

Paper presented at Mineralisation in the Caledonides, the Mike Gallagher memorial meeting held in Edinburgh, 27-28 June 1996. Oxygen isotope analysis indicates that quartz, carbonates and muscovite could all have formed in near-isotopic equilibrium with the mildly saline H2O-CO2 ore fluid at 330 degrees C. Calculated values for O, C and S in the ore fluids imply derivation from a deep, homogeneous source region and are consistent with formation either as a direct or an indirect result of igneous processes. Values for delta-O18 plot a little outside the accepted magmatic range, but have almost certainly been modified by exchange reactions with wall rocks. These reactions were also the most likely cause of deposition of the ore constituents. The chemical and isotopic character of the fluid was similar to that in many Archaean and later mesothermal auriferous vein systems, especially the Mother Lode region of California. If the Southern Uplands-Longford Down accretionary complex conceals an Ordovician arc, the tectonic setting was also broadly comparable

Jun 19, 1905

Humankind's interest in measurement of human physical strength probably dates to the first humans. At that time, life was truly a struggle in which the fittest survived. To a great extent, fittest meant strongest. Interestingly, current interest in human physical strength in the workplace stems from 1970-1980s vintage research demonstrating that persons with adequate physical strength are less likely to be injured on physically demanding jobs. Survival in many modem workplaces may still be a case of survival of the strongest. There is, however, a flip side to this issue - that persons with limited strength are more likely to be injured on "hard" jobs. To address this problem, we can apply what we know about physical strength to job design. "Hard" jobs can be redesigned to be within the physical strength capability of most people. Since physical strength is important to these jobs, we must find ways to quantify it through testing. This publication concerns human physical strength testing. Its purpose is not to recommend any particular type of testing, but rather to describe the types of testing available and their uses. It is up to each individual user of strength testing to decide which testing technique is most appropriate for his or her particular application. This booklet discusses four types of strength testing: isometric, isoinertial, psychophysical, and isokinetic. Human Strength Before describing the different types of strength measurement, we must define the term "strength" and explain the concept of strength measurement. Strength is defined as the capacity to produce force or torque with voluntary muscle contraction. Maximum strength is defined as the capacity to produce force or torque with a maximum voluntary muscle contraction.(1,2) These definitions include some key words that must be explained. A voluntary muscle contraction is "voluntary." When a person's physical strength is measured, only the effort the person willingly puts forth at the time is measured. Thus, when we test a person's "maximum strength," we are not measuring his or her actual maximum, but some lesser value representing what he or she is comfortable expressing at the time with the existing equipment and environmental conditions. Interestingly, when researchers startled persons being tested (e.g., by setting off a starter's pistol behind them), they have found significant increases in measured strength.(3) It has been hypothesized that the lower strength displayed during normal testing provides a margin of safety against overloading and damaging muscle tissue. The test equipment and the tested person's familiarity with the process also influence the "voluntary" strength output. The interface between the tested person and the test equipment is particularly important. A poorly designed interface induces localized tissue pressures that vary from uncomfortable to painful. In this situation, testers are measuring voluntary discomfort tolerance - not strength. It is important for strength researchers to keep the "voluntary" nature of their data in mind when they are designing their equipment and protocols.

Jan 1, 1998

By A. D. McMahon

Changes in world mine and smelter supply sources of zinc have led to changes in zinc supply patterns in the United States during the past 3 years, 1970-72. The result has been a growing reliance on foreign sources of zinc metal to furnish an ever-increasing portion of expending domestic requirements. This review of fundamentals and historical developments is intended to provide background in order to place the future of the U.S. zinc industry fn perspective. The properties and uses of zinc are described. A new study on U.S. reserves is presented with description by geographical region and comparisons with older reserve data. The technology of the zinc industry from prospecting through refining is described with emphasis on the metallurgy involved in the various methods of smelting. Production, consumption, and imports are discussed and illustrated with graphs and tables to review the past and present patterns. Government actions affecting the industry are shown.

Jan 1, 1974

By D. M. Wyslouzil

"This paper was prepared for presentation at the 16th Canadian Mineral Processor's Annual Meeting, Ottawa, Ontario, Jan. 17 to Jan. 19, 1984.This paper gives an account of the development of treatment procedures for the differential flotation of refractory copper-zinc ores. Special references are made to the effectiveness of various zinc depressants and their combinations.Studies carried out on refractory copper-zinc ores demonstrated that conventional zinc depressants such as cyanide and zinc sulphate were not particularly effective when secondary copper minerals were present in the ore; the flotation activity of sphalerite was enhanced in the presence of cyanide.Among the various zinc depressants evaluated, the following depressant combinations were found most effective: Zn(OH) 2-S02 , 802-CaO, Na2S-Na2S03-S02, Na 2 S-S02 and Na 2S-S0rDS22.The practical application of any of these systems depends on the type of ore treated and other conditions such as pH, levels and points of collector and depressant additions.In this paper the effect of each depressant combination on different ores is described with reference to the selection of collectors."

Jan 1, 1984

By D S. Preece

The aim of the present work is to investigate the effects of shooting multiple explosive charges, in the same borehole, on the amplitude and frequency content of the generated seismic wave. The work also investigates the effect of the coupling medium used in the borehole on the quality of the generated seismic wave. The delay period between the shots is on the order of months and up to a year. The investigation utilizes a numerical modeling approach which is capable of modeling the detonation of explosives as well as shock and stress wave propagation in solids.

Jan 1, 2012

By Doug Tesarik

Researchers from the National Institute for Occupational Safety and Health1 (NIOSH), together with employees from The Doe Run Company, are monitoring and evaluating the stability of a pillar retreat section at the Fletcher Mine, a lead/zinc, room-and-pillar mine near Bunker, MO. Cemented rockfill is being used to provide roof support as high-grade, remnant ore pillars are mined. Earth pressure cells and deformation meters placed in backfill panel pillars monitor stress change and vertical deformation, respectively, as nearby ore-bearing pillars are extracted. Similarly, biaxial stressmeters and borehole extensometers are used to monitor mining-induced stress change and deformation, respectively, in long-term support pillars. Data from these instruments indicate that when ore-bearing pillars were mined, stress was redistributed from support pillars to a backfill panel pillar. The data also indicate that the backfill and support pillars have remained stable for two years after pillar extraction was completed in the area. This research demonstrates the importance of using reliable instruments to document the geomechanical behavior of pillars and backfill. Gaining a better understanding of roof support and stress redistribution mechanisms is a fundamental part of NIOSH's goal to reduce and/or predict rockfalls, which are still among the leading causes of injuries in metal/nonmetal underground mines.

Jan 1, 2006

By B. M. O'Harra

Zinc smelting is frequently termed a ba.ckward art. The term is hardly true, for great progress has been made in recent years in the design and in the thermal efficiency of the retort furnace, in the quality of retorts, in the recovery of zinc, and in the ability to treat more impure and complex ores. The fact remains, however, that the peculiar physical and chemical properties of zinc have delayed such immense advances-large smelting units, high recovery, lowunit costs, and ability to treat low-grade ores-as have been made in the metallurgy of lead and copper. In current retort-smelting practice, the ores, if carbonates, are calcined to remove carbon dioxide; or, if sulphides, are roasted to remove sulphur. The sulphur must be eliminated as completely as possible, usually to less than 1 per cent. This means that the roast must be continued for a long time at a high temperature, with resulting high cost and small capacity per furnace. The roasted ore is mixed with about 50 per cent of its weight of reducer, which may be fine coke, anthracite, or nonbituminous coal. This mixture is charged into horizontal fire-clay retorts. The retorts used in this country are about 8 inches in internal diameter by 4 feet in length and hold 50 or 60 pou~ds of ore. The diameter of the retort is limited by the tirrie required for the heat to penetrate to the center of the charge; the length by the strength of the retort, which at the high temperature employed can not support the weight of the charge if the span is more than about 50 inches. The retorts are heated externally by coal, natural gas, qr ·producer gas to a temperature of 1,200° C. or more. The zinc oxide is reduced to zinc, which is volatile at this temperature, and passes into a conical fire-clay condenser. attached to one end of the retort, where it conde_nses to liquid zinc and is removed. Twenty-four hours are required for distillation, and because of the low heat conductivity of the retort walls 11.nd of the ore charge itself, the heat efficiency even of the most modern regenerative furnacei;; is only about 12 per cent. The retorts have a short life, 30 to 6Q days, at the high temperature required-; zinc losses are heavy, usually 10 per cent or more; and the proportion of impurities in the retort charge must be carefully controlled to prevent the rapid corrosion of retorts. For these reasons, much work has been done in an e:ff ort to, find cheaper and more efficient methods o.f recovering zinc from its ores. Various methods have been proposed for smelting in the blast furnace. Some of these contemplated the production of zinc vapor and its condensation to liquid; others attempted to produce liquid zinc directly by smelting under pressure. It is now realized that fundamental difficulties render these proposals impracticable. The electric furnace for smelting offers obvious advantages in the way of the efficient utilization of energy, large units, easy attainment of high temperatures, and the possibility of treating complex ores. E. H. and A. H. Cowles first suggested a design for an electric furnace for the reduction of zinc ores and patented their process in 1885. Their attention was soon directed to other uses for their furnace and nothing further of importance was done in the electric smelting of zinc until about 1900. Several investigators then started work upon various processes and had more or less success. The chief difficulty they encountered was the impossibility of obtaining more, than a small amount of the zinc as liquid metal because most of the zinc vapor condensed as blue powder. Interest in the electrothermic metallurgy of zinc increased, many patents on processes and furnace design were taken out, and the literature on the subject grew, until in 1914 and 1915 the problem seemed to be approaching solution. About this time the hydrometallurgy of zinc, the development of which had been lagging somewhat behind that of the electrothermic metallurgy, sprang into the limelight and a commercial process was soon perfected. This rapid development, perhaps aided by the war premium on the high-grade spelter produced by electrolytic deposition, distracted attention from electric smelting to some extent, though progress continued. With the perfection and standardization of the electrolytic process has come a better realization of its limitations, especially the necessity for large-scale operation ·and the difficulty of obtaining high extraction. Because of these limitations the electrothermic metallurgy of zinc still has a field of its own and in fac-t promises to become a strong competitor of both hydrometallurgy and retort smelting except under conditions highly favorable to the latter methods. Because of the imperfections of the retort and electrolytic processes and the promise that the electric furnace offers in overcoming these imperfections, the. United States Bureau of Mines, in cooperation with the Missouri School of Mines and Metallurgy, has undertaken a study of the electrothermic metallurgy of zinc.

Jan 1, 1923

By R. V. Ramani

This report is volume 2 of an eleven-volume final report for a Grant completed by The Pennsylvania State University for the Bureau of Mines to develop a dynamic general purpose computer simulation model for underground coal mining. The simulator developed under the Grant has a wide range of possible applications in the design and evaluation of underground coal mining systems from the standpoints of health and safety, productivity, and mine environment. The Master Design Simulator consists of nine free-standing function-oriented subsystem models linked together into an integrated, comprehensive model of an entire mining system. The subsystems comprising the Master Design Simulator include geology and reserves, methane generation, roof support, subsidence, production, rail haulage, cost, water generation, and ventilation. This volume of the final report describes the Geology and Reserves subsystem of the Master Design Simulator. The two functions of this subsystem are: 1) the design of a geological data library to provide input to the other subsystems of the simulator; and 2) the calculation of coal reserves and associated values and grades under various user-specified conditions. The subsystem uses a weighted moving average method to interpolate between the borehole values, and provides output in report format, graphical plots and/or storage on magnetic tape or other storage devices for later retrieval. The application of the subsystem as an independent model with test results and comparisons with other methods of computing reserves is also presented. The appendix comprises a users manual for the model, and includes a program listing.

Jan 1, 1974

By James C. Patterson

Sintered fly ash was shown to have promise as a modifier for poorly drained soils. Turf grown in mixtures of sintered fly ash and soil benefited from increased water-infiltration rates, greater total pore space, and higher moisture availability, The result was an improved turf stand with increased grass yield and root density.

Jan 1, 1970

Bacterial leaching represents an unusual problem in biochemical engineering, because the substrate for bacterial growth is not supplied directly, but is a product of another reaction, the leaching of mineral particles. Leaching arises from the bacterial oxidation of ferrous ions to ferric ions, which in turn oxidize the mineral. For the bacterial dissolution of pyrite, these reactions are: [ ] (Y represents a stoichiometric yield factor, and N represents the amount of bacteria.) Equations [1] and [2] represent a cyclic auto-catalytic system since more ferric ions are added to the system with an increase in the extent of leaching.

Jan 1, 2000