Search Documents

The polymerisation of silica is found to interfere with thickening of leach pulps at Risdon. Hydroxyl ion and fluoride ion are catalysts for this reaction. Stability may be obtained by the presence of aluminium or ferric iron.INTRODUCTIONAt Risdon it has been a matter for satisfaction that, although the concentration, of silica in leach solutions is appreciable, it has ,given relatively little cause for anxiety.However the margin of safety is small and some intermittent difficulty in thickening leach residues during the last few years has prompted a further investigation, certain parts of which are described here since they may be of general interest.Leaching and ClassificationThe method of leaching which is practised at Risdon has been described in, two previous articles, by W. C. Snow (1936) and S. W. Ross (1949) to whiCh the reader is referred for detail. Continuous leaching is practised, the circuit solution flowing through five air agitated pachucas in series, to tlie first of which calcine is added. The circuit solution, which also enters the first pachuca, consists of spent electrolyte from, the electrolytic cells and contains 90 -gm. of free sulphuric acid per litre. About 80 per cent of the solublezinc oxide is extracted from the calcine in the first pachuca, at a pH value of 1-1 (7 gm.H2S04/1 at 55 to 60°C. In the later pachucas the leaching rate decreases sharply. The leach pulp which leaves the 'last pachuca contains an average of 17 gm. of free acid per litre, corresponding to a pH of 1.7; but, owing to variations in extraction, the end point fluctuates between 2.5 and 0·3 gm. free acid per litre (pH:> 1·5 to 2.5). The average flow through the plant is 1,250,000 gallons per day, which corresponds to a production of 300...

Jan 1, 1958

By Patrick J. Cain

The fatigue-failure characteristics under high-frequency (10 KHz) cyclic loading were determined for a marble, granite, and quartzite. The rock speci-mens were cyclicly loaded (using a high-power piezoelectric sonic transducer) at a constant strain amplitude generated by forming a longitudinal standing stress (strain) wave in the cylindrical test specimen. The number of load cycles required to fail each rock type at a given strain amplitude was deter-mined. The fatigue fractures were tensile in nature and the fracture load amplitudes were as low as 30 pct of the static tensile strength. Also the internal heating of the rock caused by the material damping (internal friction) was measured. The damping and internal heat generation in the specimens was analyzed to show that nearly all of the power input can be accounted for as a change in enthalpy in the specimen. Using these results the thermal strain in the rock was calculated to evaluate its contribution to fatigue failure. The thermal strain was found to range up to 30 pct of the dynamic strain amplitude depending on the load amplitude and the number of load cycles. The specific energy required for failure was determined and possible applications of the high-frequency fatigue fragmentation process are discussed.

Jan 1, 1975

By L. B. Berger

The Haldane gas-analysis apparatus used by the Bureau of Mines is patterned after the device developed by Haldane 4/ and differs from it only in structural modifications that have been added to facilitate operation and simplify construction. The apparatus was developed to permit determination of carbon dioxide, combustible gases, and oxygen with a degree of accuracy not attainable with apparatus of the types ordinarily used for the analysis of fuel gases, flue gases, and similar mixtures. The Haldane apparatus is used by the Bureau of Mines chiefly in the analysis of air samples collected in coal and metal mines and other underground workings and is applied also in the analysis of many other types of gas mixtures when accurate determination of certain constituents is desired.

Jan 1, 1938

By L. Connolly, F. R. De Luca

"Rubber liners at Denison Mines Limited are used in 10 1/2x 24' low discharg0 pebble mills. These were originally 10 1/2 x 13 Dominion overflow type ball mills. Experience here shows that the wear of rubber and ni-hard lifters is approximately the same in the feed end half of the mill, while the wear of rubber lifters is much greater in the discharge half. The wear of rubber plates is considerably less than white iron in the feed end half of the Mill and slightly more in the discharge end half of the Mill. Rubber components are lighter to handle but their installation is time consuming. This leads to the conclusion that a combination of ni-hard lifters a~~ rubber plates is the most economical compromise in Denison's case, for the Mill. Rubber discharge grates are superior to steel grates, while steel feed end liners are superior to rubber.The Use of Rubber Mill Liners at Denison Mines LimitedGrinding is done in two identic0al circuits each consist-ing of one 10 1/2 x 14' Dominion overflow rod mill, two Dorr Oliver quadraplex rake type classifiers, two 10 1/2 x 24' Dominion low discharge grate pebble mills and ancillary pumps and conveyors for pebbles. There is one centrally located distributor box that receives the discharge of the 4 pebble mills and splits it out to the classifiers."

Jan 1, 1974

By C Adams

Reports of delays and cost blowouts in major study and construction projects are becoming increasingly prevalent in the resources industry. This is mainly being attributed to an escalating cost environment associated with the increased number of projects in the development to construction pipeline and a scarcity of competent skilled resources to deliver these projects. However, not all this effect can be directly attributed to the current environment. Historically the mining industry has not performed well in its ability to deliver projects according to the financial and physical parameters forecast in the feasibility study process. To manage the risks associated with delivery of major projects, resource companies need to ensure they use a standardised approach to management of their project development to satisfy project objectives and enable more efficient use of the increasingly limited available resources. Each discrete step in advancing the project from scoping study to operations needs to be integrated, reducing the amount of rework and duplication. This paper is primarily a consolidation of existing ideas on project management systems but also introduces new concepts to solve current issues. It describes the basic components of a typical mining project, the issues that commonly arise, the key attributes, and critical steps required for an effective integrated project management system covering projects from initial scoping studies through to project commissioning and operation. This paper focuses on technical study components of the mine development project with allowance for transitioning to design and construction and operation phases.

Jan 1, 2006

By A. B. Cecala

A few years ago, the National Institute for Occupational Safety and Health and Unimin Corporation developed a clothes cleaning system that is able to quickly, effectively, and safely remove dust from a worker?s clothing without dust exposure to the worker, the work environment, or co-workers during the cleaning process. To perform the process, a worker enters a cleaning booth and activates an air spray manifold which blows the dust from the worker?s clothing. Since the cleaning booth is under negative pressure, all the dust and product removed are contained. In the original design, this dust-laden air was exhausted to a dust collector system. However, since most operations do not have excess dust collector capacity, it was decided to determine an alternative method to provide for a stand-alone cleaning system. This was achieved by ducting the exhaust outside the plant and into the atmosphere. This technique was recently tested and shown to be a viable method to provide for a stand-alone clothes cleaning system.

Jan 1, 2009

By B. A. Wilcox

ThERE are several reports in the literature which indicate that both solid-solution hydrogen and hydride precipitates can promote low-temperature em-brittlement of tantalum.1-3 For example, Imgram et al.2 showed that hydrogen additions in the range of 140 to 580 ppm promoted a ductile-to-brittle transition at slightly above room temperature in both wrought and recrystallized tantalum. This contrasts with the observation that tantalum of norma1 purity is very ductile, even at liquid-nitrogen temperature. Imgram et al. also found that hydrogen additions caused a deterioration of notch tensile properties of tantalum. The purpose of this communication is to present some limited evidence that hydrogen can also cause fatigue embrittlement of tantalum. The material used in this investigation was wrought, stress-relieved (1000°C, 1 hr), are-melted tantalum rod (5/8-in. diameter) containing the following impurities in weight percent: 0.005 C, 0.007 02, 0.0005 H2, 0.003 N2, 0.08 Cb, 0.01 W, and 0.01 Fe. Hydrogen charging was done in an atmosphere of flowing dry hydrogen for 3 hr at 600°C, followed by an homogenizing anneal in purified argon for 15 min at 600°C, and cooling in an argon atmosphere. Typical micro-structures of the hydrogen-free and the hydrogen-charged materials are shown in Fig. 1(a) and Fig. 1(b), respectively. Fig. 1(b) shows the appearance of hydride precipitates which, in many cases, formed preferentially parallel to the rod axis. The hydride dispersion was uniform across the diameter of the specimen. The fact that the precipitate was a tantalum hydride was tentatively confirmed by X-ray diffraction on a metallographically prepared surface. After hydrogen charging, chemical analyses by vacuum fusion revealed the hydrogen content to be 0.0295 wt pct. In addition, the oxygen and nitrogen contents were slightly raised to 0.0095 O2 and 0.005 N2.

Jan 1, 1964

By Burton Scott

A device for detecting carbon monoxide at ppm levels is described which is based on the measurement of infrared absorption at 4.65 microns. The unique feature of the nondispersive infrared instrument is contained in the optical design which includes a confocal cavity, increasing the effective optical path length by a large factor, thus greatly reducing the required package size. The cavity has the effect of reducing the total amount of radiation passing to the detector, but at the same time increasing the percent attenuation observed when adding CO, by a factor called gain. The radiation is chopped by a filter wheel which contains narrow band filters at 4.0 and 4.65 microns. The resultant signal produced by the pyroelectric detector is demodulated by the electronics to product an automatic gain control signal, proportional to the total radiation, and a difference signal, proportional to the CO present. Tests of a breadboard model are described which show cavity gains of 10 with noise levels equivalent to 2 to 10 ppm CO.

Jan 1, 1975

By J. D. T. Steyl, C. A. Biley

"The chemistry of electrolyte systems containing iron remains generally poorly understood despite their prevalence in many natural and industrial processes, particularly in hydrometallurgy. These systems are typically challenging to study and model due to their affinity for complex formation and precipitation even at low pH. Recent developments in the hydrometallurgical processing of nickel laterites at Anglo American have called for a deeper understanding of the fundamental chemistry of the Fe2(SO4)3–FeSO4–H2SO4–H2O system. This paper details the development of an internally consistent, Pitzer ion-interaction model of this system, with explicit recognition of important contact ion pairs (CIPs). The primary application of this model is a thermodynamic framework for the interpretation of kinetic processes occurring during iron(III) reduction with SO2. Adopting a rigorous thermodynamic basis for the system chemistry facilitates the formulation of simple rate expressions that are capable of inherently capturing complex effects. While the iron(III) reduction case study remains the focus of this work, the developments have more universal applications and the thermodynamic speciation model can be extended into other systems containing acidic ferric sulfate.INTRODUCTIONIron is present in nearly all hydrometallurgical refining circuits typically as both a necessary and unwanted impurity and needs to be removed and disposed in a safe and efficient manner. This is generally performed by precipitation to form a range of solids such as hematite, goethite or jarosite. Numerous studies in the open literature have focussed on the removal of iron from refractory gold sulfide ore (Berezowsky & Weir, 1989; Berezowsky et al., 1991) and zinc pressure leaching (Buban, 1999; Ismael, 2003), and PGM matte sulfide circuits (Dutrizac & Monhemius, 1986). Moreover, since ferric iron is a strong oxidizing agent, it has been used extensively as a leaching agent for sulfide minerals (Dreisinger, 2006). Given the outlook of challenging economic conditions, declining ore grades and increasing levels of impurities, effective iron management is going to become increasingly critical to all hydrometallurgical processes.Against this background, and considering the widespread importance of acidic iron sulfate systems throughout natural and industrial processes, it is unexpected that the knowledge of the fundamental solution chemistry of these systems contains such significant gaps, particularly at the conditions typically found in hydrometallurgical applications. Existing literature describing the measurement and modelling of solution speciation in these systems have highlighted their significant chemical complexity (Magini & Caminiti, 1977; Magini, 1979; Lee & Tavlarides, 1985; Stipp, 1990; Papangelakis et al., 1994; Gil et al., 1995; Majzlan & Myneni, 2005; Kormanyos et al., 2008; Yue et al., 2014). Partially responsible for the lack of quantitative speciation measurements is the strong tendency of ferric to hydrolyse at even low pH (Flynn, 1984), complicating the laboratory study of such systems. Moreover, the large number of aqueous species that may co-exist simultaneously makes the study of individual species and the modelling of the numerous interactions between these species extremely difficult (Dry & Bryson, 1988; Stipp, 1990; Majzlan & Myeni, 2005; Kobylin et al., 2007)."

Jan 1, 2016

By Edgardo Torres Hernández

El Proyecto Optimización de Ángulos de Taludes en Explotación de Minas es un proyecto desarrollados por E-Mining Technology (EMT), socio estratégico de Prodimin en Perú, para Codelco Chile en uno de sus yacimientos del Norte de Chile. El desarrollo de este proyecto estuvo enmarcado en el Programa de Proveedores de Clase Mundial; programa que tiene como misión desarrollar un sector de proveedores intensivo en conocimiento, mediante la generación de soluciones tecnológicas empujadas desde la demanda de la minería y desde la propuesta del sector de proveedores que puedan ser escaladas a otros sectores y mercados.

Sep 1, 2017

By J. Ling, L. Racine, P. Cousin, A. R. Laplante

"The problem of gold recovery by gravity from high density gangues is first discussed from a fundamental perspective. Three potential difficulties are presented: poor liberation and fine gold particle size, concentrate bed erosion by coarse dense particles, and slow percolation of gold particle through the high density gangue bed. Two case studies are presented to illustrate the impact of these three problems on circuit performance and the feasibility of gravity recovery. It is concluded that careful testing can determine the scope of the first problem and feed preparation can limit the extent of the second. The third problem is clearly the most serious and results in lower gravity recoverable gold recoveries than would be achieved with the same recovery effort on a low density gangue application.IntroductionSince the commercialisation of the Knelson Concentrator in 1980, gold gravity recovery has experienced a surge in interest, in Canada and the United States first, then Australia, Zimbabwe and Russia, and finally worldwide. Table I details number of units sold in various countries, which corresponds approximately to their importance as gold producers 1. Exceptions. such as the low rank of South Africa or the importance of Zimbabwe, despite the much higher gold throughput of the former, are generally the result of differences in the effectiveness of the local marketing strategies, as well as a reflection of the ""philosophy of recovery"" prevalent in the country.The impact of the Knelson has not been felt equally in all plants. Typically, a highly successful application falls into the following categories: (a) alluvial or hard rock recovery for which gravity is the sole recovery method, (b) hard-rock free gold milling with ores which have a very high gravity-recoverable gold (GRG) content, (c) low grade sulphide copper-gold ores which include flotation ahead of cyanidation and (d) free-milling gold ores ahead of Other applications can be successful, but are not as common. The ""explosion"" of centrifuge concentration, of which the Knelson is the most successful but by no means the sole model, has created a certain euphoria which can be summarized as ""gravity recovery will improve the profitability of gold milling, no matter what."" This presentation is about applications that are not so successful, or even downright unsuccessful. The rationale is not to down-play gold gravity recovery, but to set it in its rightful position: metallurgically, it is not appropriate all of the times; it can become inappropriate if poorly designed; and it can be metallurgically possible but economically unjustifiable. In this paper, this will be illustrated and explained rather than demonstrated, with the use of both industrial plant surveys and laboratory test work. Alternate gravity approaches will be suggested."

Jan 1, 1997

By C. O. Karacan, S. J. Schatzel, W. P. Diamond

In coal mining, longwall mining is a preferred method to maximize production by extracting large blocks of coal that have been outlined with a set of development entries. In U.S. mines, longwall panels are typically 305 m (1,000ft) wide (with a continual trend towards even wider panels), and usually over 3,050 m (10,000ft) in length. The increasing size of longwall panels, while helping to increase coal production, may also increase methane emissions due to the exposure of the mining environment to a larger area of fractured, gas-bearing strata. Thus, understanding the impact of increased panel widths on methane emissions, and designing gob gas ventholes and bleeder systems accordingly, can enhance the safety of the underground workforce by reducing their exposure to potentially explosive accumulations of methane/air mixtures. As part of its mine safety research program, NIOSH’s Pittsburgh Research Laboratory has initiated a reservoir modeling effort to better understand the interaction of the various geotechnical factors influencing gas flow within and to the underground longwall mining environment. A focus of this modeling effort has been 1) the prediction of the incremental amount of methane emissions to be expected due to increasing longwall panel widths, and 2) optimizing gob gas venthole completion practices to capture more of the gas in the subsided strata above longwall panels before it can enter the ventilation system of the underground workplace. The history matching phase of the study has been carried out on a 381-m (1,250ft) wide panel in the Pittsburgh Coalbed. Simulations have also been completed for a 442 m (1,450ft) wide panel to estimate the incremental increase in methane emissions and the performance of current gob gas venthole placement configurations. Additional venthole placement configurations were simulated to investigate options for optimizing methane capture from the subsided strata above the wider longwall panel.

By Carl Hendricks, Malcolm Scoble

There currently exists no viable means of obtaining continuous, quantified feedback on blast efficiency. This paper describes the adaptation of a loading shovel to serve as a diagnostic tool in evaluating the success of ground preparation practices. Work undertaken in a large western Canadian open pit involved microprocessor-based instrumentation for the performance monitoring of an electric mining shovel. The monitored shovel responses proved to be reliable indicators of variations in muckpile d&ability. This approach is considered to provide a very comprehensive survey of post blast conditions since the shovel must physically interact which every cubic yard of blast fragmentation.

Jan 1, 1991

By Chen Xizhe

The caisson is adapted to the foundation of concentrated heavy building. As there are the flowing sand, boulder or cobble and other serious obstruction, the open caisson can't sink, the caisson can solve these problems easily. Especially for the stability of the neighour building, the merit of the caisson is outstanding. Therefore, there are the pier, the foundation of heavy instrument and the large water pumping station etc. using the caisson in China. This paper introduce several caissons and successful experience by author's investigation. It contains the feature and application of the caisson : the examples of caissons such as a huge pier of a bridge acrossing a big river, a large instrument foundation and a large water pump station beside a river; the problem of the design of the caisson and notice items during the caisson construction etc.

Jan 1, 1991

By L J. Ingle, K L. McPhee, A G. Hunt

Iron Road Limited (IRD) is currently developing the Central Eyre Iron Project (CEIP) at Warramboo on the Eyre Peninsula, South Australia. The project consists of a 30 year open pit mine, magnetite processing facilities, standard-gauge railway and deep water, Cape class capable port. Major South Australian government approvals have been received and funding arrangements confirmed.The 4.5 Bt Mineral Resource (3.7 Bt Ore Reserve), the largest in Australia and among the largest globally, is to be mined to produce 24 Mt/a high-grade, 67 per cent Fe, magnetite concentrate. This in-demand, premium product has a P80 of ~100 µm, suitable for both direct sinter feed and an additive in pelletising.The extensively drilled, homogeneous orebody is unique in both geology and mineralogy; only averaging 15 per cent Fe yet coarse-grained with almost negligible phosphorus and sulfur content. This has allowed significant opportunities to tailor the mining method to the orebody, utilising both optimised blasting as first stage comminution, as well as in-pit crushing and conveying (IPCC) to reduce the heavy haulage diesel fleet and optimise the pit shell.Approximately 1 Mt/d of total material, ore and waste, is required to be moved from the pit daily, introducing materials handling challenges, overcome by a flexible IPCC set-up, multiple overland conveyors and an exacting mine plan. Non-conventional waste and tailings storage is utilised to allow for significant water savings, progressive rehabilitation and minimisation of land impact.The processing facilities utilise both the magnetic and density properties of the magnetite to beneficiate the ore. The coarse-grained nature of the ore is exploited to minimise comminution yet still liberate a high quality product. Utilisation of modular construction methods allows risk reduction during construction and reduced pumping requirements during operation.This paper highlights the uniqueness of the CEIP, with focus on the mineralisation of the orebody, and the beneficial impacts this has on both the proposed mining method and processing. Magnetite mining is not new and IRD has used the learnings of others, and input from various vendors and industry experts, utilising knowledge and expertise to engineer an innovative, yet supported, project design.CITATION:McPhee, K L, Hunt, A G and Ingle, L J, 2017. The Central Eyre Iron Project – developing a new iron ore mine in a challenging climate, in Proceedings Iron Ore 2017, pp 613–620 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 24, 2017

By Javier Támara

Para aumentar la productividad de la empresa minera es necesario conocer el sistema de aire -en tanto se prioriza los intereses de los clientes, y así se puede suplir todos los componentes necesarios para garantizar una máxima eficiencia y confiabilidad del sistema completo de aire comprimido que va desde el filtro de admisión hasta el punto de uso. En ese sentido, el presente texto describe las estrategias para realizar Solucionazing en ahorro energético y así aumentar la produtividad de los sistemas de aire.

Aug 25, 2002

By Roger L. Baer

Marine disposal of mill tailings has been practiced worldwide for over a century. However, only recently have the environmental effects of marine disposal been systematically studied. Some early attempts at marine disposal of tailings resulted in adverse impacts to marine life. However, recent advances in tailings disposal methods have included the introduction of engineered submarine tailings discharge systems, advanced environmental assessment and monitoring methods, and oceanographic modeling systems. Successful submarine tailings disposal (STD) has occurred at several mines. The U.S. Bureau of Mines (BOM) has undertaken studies of the disposal of mining and milling wastes in the marine environment. The BOM Alaska Field Operations Center, Juneau, initiated a review of the technology, regulations, and economic aspects of STD. The review illuminated the need for organization of literature on the subject, therefore the Bureau compiled this extensive bibliography on marine disposal of mill tailings. The bibliography presented here contains 1483 references and is also available through diskette in the Word Perfects format. A review of the references indicates that literature on submarine disposal inadequately covers the subject. The majority of the references listed only peripherally relate to the subject. Published literature on the engineering and environmental aspects of STD is severely limited.

Jan 1, 2011

By Chas. F. Jackson

The annual reports of the supervising engineers of the seven sections comprising the Mining Division are assembled in the following pages and constitute the annual report of the division. In planning activities, the aim has been to adapt the work to changing conditions and needs of the mining industries and to avoid becoming bound to any particular type of investigation when others are found to be of more pressing interest.

Jan 1, 1939

By A. K. C. Chan

Recent hotel investment projects in China often involve very tight programmes for design and construction. An example given in this paper involves a 24-storey reinforced concrete hotel tower with 460 bedrooms and a 3-level podium commercial complex. The building is supported by relatively widely spaced columns and shear walls below which 88 number large diameter piers were excavated through fill, silty and bouldery clay on to dolerite and slate at depths between 15 to 3 0m below ground level. Whereas much experience has been accumulated in Hong Kong, hand-excavated pier foundation was only adopted for the first time in Dalian. This paper describes and discusses the various factors influencing the choice of the type and design of the foundation system. The criteria for determining appropriate founding levels are then explained. During installation, revisions to the acceptance procedure were made to cater for local conditions. Emphasis is placed on the role of the geotechnical engineer in making on-site decisions during construction. The advantage of the foundation system in accommodating on-site changes resulting from local complex ground conditions is demonstrated. The pier foundations were successfully completed ahead of programme.

Jan 1, 2010

By W. R. Herrera

A research effort was conducted to present or develop methodology for evaluating candidate potting materials intended for use in explosion-proof enclosures. The primary purpose was to develop acceptance guidelines based on arc decomposition products. Acceptance criteria can be based on: ? Inherent thermo-chemophysical, mechanical and electrical properties; ? Arc decomposition products: ? Nature of volatile products produced, e.g., flammability, explosivity, synergistic effects on existing environment in the enclosure, toxicity; ? Quantity produced as a function of arc power and duration; ? Acceleration aging tests to evaluate breakdown under electrical stress.

Jan 1, 1982