Search Documents

By V Kveldsvik, N Ragvin, T Eiken, G Grøneng, G V. Ganerød

Catastrophic rock slope failures have caused destructive tsunamis in Norwegian fjords. At the Åknes rock slope the tsunami generating potential is large due to the potential large volume involved in a possible catastrophic failure. Widening of the upper crack has been recorded since 1986, and in recent years, a quite extensive investigation and monitorin campaign has been conducted. Data from some of these investigations are presented and analysed with respect to a preliminary evaluation of the stability of the slope.

Jan 1, 2006

By Kyle Selga, Christopher J. Greet

"The Pulp Chemistry Monitor (PCM) has been installed and operated in a number of concentrators in Australasia, and has produced some very interesting results. PCM measures the pH, Eh, dissolved oxygen, temperature and oxygen demand of process streams within a concentrator continuously and in real time.In the example presented in the paper the cleaner feed pulp chemistry is measured, and related back to changes in the mineralogy as well as variations in metallurgical response. For example, a decrease in Eh and dissolved oxygen as well as an increase in the oxygen demand. These changes in the pulp chemistry appear to coincide with increases in the feed grades, probably higher pyrite grades. Further, these variations in pulp chemistry and feed mineralogy have a negative impact on the concentrate grade and recovery.The implication is that if the pulp chemistry is monitored it is possible to predict changes in the mineralogy of the system, and from this the metallurgical response. Further, the changes in pulp chemistry can be used in a control system to counter the changes in mineralogy and maintain the metallurgy.IntroductionIt has long been recognized at a fundamental level that the flotation behaviour of sulphide minerals is dependent on the pH and Eh of the system (for example: Tolun and Kitchener, 1964; Woods, 1976). However, measuring pulp chemical parameters within an operating concentrator has had limited attention. Woodcock and Jones (1970a and b) were among the first to actually collect data from operating plants. Jones and Woodcock (1984) identified some of the chemical complexities of flotation pulps, and noted that most concentrators already operate at high levels of metallurgical performance but there was still considerable scope for improvement. These gains would, in part come from more effective chemical control. In the same volume, Healy (1984) discussed metal ion hydrolysis and precipitation, redox chemistry and how the surface chemistry of sulphide minerals can be influence flotation behaviour. The impact of grinding environment on the pulp chemistry and flotation response of a complex polymetallic sulphide ore is discussed by Forssberg and Subrahmanyam (1993). Their work essentially contrasts the pulp chemical and flotation performance of pulps ground with conventional ferrous grinding media to a fully autogenous system. The data suggested that the reduction or removal of iron hydrolysis contamination from the system could have a positive influence on flotation behaviour, and perhaps the first stage of “controlling” the chemistry of the system should be in the grinding circuit. Grano et al (1995) demonstrated that the collection of pulp, solution and surface chemical data could identify weaknesses within a concentrator, and from these data develop, test and implement solutions that improved the process. Greet et al (2006) showed that the pulp chemical trends observed through primary grinding and rougher flotation circuits of most sulphide flotation concentrators are approximately the same. There are differences in the magnitude of various pulp chemical parameters (pH, Eh, dissolved oxygen, temperature and oxygen demand) as a result of variations in the feed mineralogy and processes employed. Further, it was noted the Eh shifted to more reducing values of the ten days measurements were collected, and this change could be traced to an increase in the iron sulphide content of the feed. Metallurgically, this resulted in an increase in nickel recovery through the recovery of nickeliferous iron sulphides, and a decrease in nickel concentrate grade."

Jan 1, 2016

1. New books P. Sarnoff. Trading in gold. Cambridge, Woodhead- Faulkner, 1980. 136 pp. £3.50 by airmail. Environmental Planning Professions Interdisciplinary Committee (EPPIC). Proceedings: Joint EPPIC/Habitat Symposium: Shaping Our Environment. Johannesburg, EPPIC (P.O. Box 61019, Marshalltown 2107), 1980. R3 per set of 2 issues. H. P. Patra and K. Mallick. Time-varying geoelectric sounding. Amsterdam, Elsevier, 1980. 420 pp. D.S. $87.75. Die Suid-AfrikaanseSteenkoolverwerkingsvereniging. Steenkoolvoorbereidingskursus. J ohannes burg, die Vereniging, 1930. 335 pp. Members of Chamber of Mines of South Africa R15, nonmembers R40. D. R. Derry. A concise world atlas of geology and mineral deposits. London, Mining Journal Books, 1980. HO pp. £26.25 byairmail. 2. Journal Remote sensing of environment (RSE). 3. NIM reports Report No. 2064 The on-line monitoring of gold in barren solutions. Report No. 2065 The determination, by X-ray-fluorescence spectrometry, of gold, silver, and base metals on activated carbon. Report No. 2068 The determination of platinum, palladiuim, rhodium, and gold in ores and concentrates by the fusion technique with lead as the collector. Report 2061 The determination, by anodic-stripping voltammetry, of copper and lead in silicate reference materials. Report 2062 The reduction by computer of photoplate data obtained by spark-source mass spectrornetry. Report 2071 The determination, by X-ray-fluorescence spectrometry, of tin and tungsten in scheelite and ca8siterite ores and concentrates. Tunnelling Tunnelling '82, the third international symposium in the series, is being organized by the Institution of Mining and Metallurgy, with the co-operation of the British Tunnelling Society, the Institution of Mining Engineers, and the Transport and Road Research Laboratory.

Jan 1, 1980

By Poi G, Madgwick J. C, Davis P, Pannowitz D, Cho D, MacKay B, Chan S. M, Varga R. A, Chun U

Periodic dilute sulphuric acid treatment ofstill, batch-fed, molassesenriched, microaerobic, manganese-dioxide-Ieaching microbial cultures led to marked improvements over untreated cultures. Percentage Mn++ recoveries increased (7X), rate of Mn++ formation improved (3X) and yields of Mn++ per molasses use were more economical (5 X). The yield in terms of molasses used improved with decreasing sugar used (eg 1.17 g Mn++/gram molasses at 0.2 per cent molasses (w/v) feed and 24 per cent (w/v) pulp density MnO2 tailings). The most effective Mn++ leaching in terms ofpercentage recovery (97 per cent) and rate ofleaching (46 mg Mn++/day) was at 0.5 per cent molasses (w/v) and 14 per cent pulp density (w/v) MnO2 tailings.

Jan 1, 1986

In line with DML Resources continual forward management policies, the Roscommon Quarry operation has recently installed and commissioned a Nordberg 7 ft Symons cone crusher and a HP 300 cone crusher. Both machines have enhanced the production capabilities and quality control of the Roscommon comminuition circuit and they will provide efficient and reliable crushing well into the next century.

Jan 1, 1994

The assistance that can be gained by the use of aerial photographs in the geological examination of a mineral field is clearly illustrated by the results of a rapid reconnaissance survey of the newly-discovered Mount Fitton talc, deposits, situated in the north-eastern extension of the Flinders Ranges in South Australia.The talc deposits were found to occur about the margins of a large lenticular mass of dolomitic marble, interbedded with hornfelsic tillites and fluvio-glacial sediments of Upper Pre-Cambrian age. Aerial photographs show clearly the extent of the dolomitic marble on which the growth of a species of eucalypt-Eucalyptus Gillei-is prominently developed, and which assists in defining the limits of this relatively light-coloured formation. (See Fig. 1).Upon field investigation it was found that the talc, deposits are related closely to the margin of the dolomitic marble where the latter has been subject to minor folding and faulting. The deposits themselves have been formed by metasomatic replacement of schistose dolomite. The contact of the dolomite with the underlying and overlying glacial beds is also noteworthy for the presence of minor occurrences of copper, silver, lead and zinc minerals.An examination of photographs covering a wide area reveals an outcrop of a massive granite to the north-east of the dolomitic marble, Fig. 2, which was almost certainly responsible for the regional metamorphism of the dolomitic and glacigene sediments, and the source of the mineralising solutions.All these features, as well as the broader structural features of the area, which are extremely important in the understanding of, individual commercial depQsits, were quickly determined with the assistance of the photographs.It is useful, briefly to relate the procedure adopted in examining this recently developed field as an example which may be well worth following on other fields, even if exposures are not so clearly defined. The method to be outlined, of course, will be of maximum advantage. Where rock exposures are good, where the ore bodies are likely to be widely spread, and where such bodies are related to some major geologi-cal control. Typical of such deposits are pegmatitic, hydrothermal and related ore bodies associated with the periphery of an igneous intrusion, or ore bodies related to particular sedimentary horizons in a regionally metamorphosed province.Procedure.The first requirement is the preparation of a detailed reconnaissance geological plan of as large segment as possible of the potentially mineralised province. The use of aerial photographs is par...

Jan 1, 1950

By Jose R. Hernandez-Aguilar, Jeet Basi

"The study evaluated the impact on overall circuit metallurgy of improving the performance of the two flotation columns that make up the final Mo cleaning stage in the Cu/Mo separation circuit at Highland Valley Copper mine. The results showed that a key factor to improve the overall circuit metallurgy was to control the size of the bubbles generated in the columns. When a large proportion of small (< 1 mm) bubbles were generated, the production rate of solids-in-concentrate increased by a factor of 4-5 compared to typical production figures without compromising concentrate quality. This increase in concentrate production rate reduced the circulating load in the circuit causing a significant increase of Mo recovery. A statistical analysis of historical production data showed a strong relationship between final concentrate production rate and overall Mo recovery. This relationship along with the results from this study indicated an opportunity to increase the recovery of Mo from 90% (typical) to 94% without downgrading concentrate grade. This 4% increase represents about 14,000 lbs or $500,000 worth of Mo each month at current metal prices.To provide a rational interpretation of the results, this study also examined whether the model of Gorain et al. (1997; 1998; 1999) could explain the increase of Mo recovery seemingly resulting from the decrease of bubble size. The data showed that the model predictions did not agree with the experimental data, i.e., for a given change (decrease) of bubble size, the predictions underestimated significantly the observed recovery increase. An interpretation based on the fundamental analysis of Finch and Dobby (1990) and Hernandez-Aguilar et al. (2005) is proposed to explain the discrepancy between measurements and predictions obtained from Gorain et al.’s model.INTRODUCTIONIt is generally accepted that the size of the bubbles generated in a flotation cell – a concept usually referred to as “bubble size” – has a significant effect on metallurgical performance. However, a significant number of mineral processing practitioners often question, with valid reasons, the practical benefits of implementing process improvement strategies based on controlling bubble size. “Small” bubbles are often considered to be “favourable”, but how small they need to be for a particular case, or how to adjust operating conditions to control a target bubble size, or whether the bubbles need to be smaller in the first place are questions that usually remain unanswered. Two reasons explain this situation."

Jan 1, 2009

In general, the metallurgical industry has so far been slower than the chemical industry to adopt ion exchange materials for industrial processes. The atomic energy industry presents a marked exception to this general situation, and the literature shows a rapidly increasing use of ion exchange techniques for the recovery of atomic energy metals on scales ranging from the ultra micro up to that of the largest mining operations. In many cases, the processes used would be equally applicable to more common metals and it is hoped that this review will be of interest to metallurgists outside the specialised atomic energy field. The review is intended to describe developments of ion exchange processes made during the last three years. Earlier studies have been summarised by Kunin and Preuss (1956) and Roland (1957). In order to restrict the number of references discussed, purely analytical procedures have been omitted and only those processes which have been conducted on a reasonably large scale or which, from their nature, areclearly capable of being upscaled, have been considered. The paper is divided into five main sections concerning respectively:Water treatment and effluent disposal.Metal recovery and purification.New ion exchange materials.New ion exchange equipment.Membrane cells.WATER TREATMENT AND EFFLUENT DISPOSALA high proportion of atomic reactors, and particularly those of American design, are cooled by water which is...

Jan 1, 1961

By Walter Valery, Peter Radziszewski

"The NewCrest Cadia operation boasts the largest SAG mill commissioned last June 1998. A request was made to shed some more light on possible SAG mill charge behaviour. Three different software were used to simulate SAG mill charge behaviour:Mishra/Rajamanis MillSoft DEM charge motion program, Radziszewskis agglomerated DEM charge motion program and Powell/Nuricks MillTraj outer trajectories program. The contexts simulated are: 20/30 % charge volume, 65/75/85 % critical speed using the Hi-Lo lifter configuration specified for the mill as well as a Hi-Lo 60 degre lifter face configuration. Further, lifter interval was also studied to determine the effect on power draft. Power predictions are compared with those obtained during the commissioning period.INTRODUCTIONThe NewCrest Cadia operation is located outside of Orange, New South Wales, Australia. With proven reserves of 190 million tonnes at a grade of 0.75 g/t Au, the mill was designed to process 17 Mtpa (2065 tph) of ore with an 86% copper and 73% gold recovery. The grinding circuit (Fig. 1, Table I) boasts the largest SAG mill (Fig. 2) and was commissioned last June 1998."

Jan 1, 1999

By M. T. Baquera

A comparison of microstructures associated with W single-crystal ([001], [011], [111]) rods prior to deformation (as grown), and after quasi-static compression (at a strain rate of ~1/s) by transmission electron microscopy (TEM) shows several orders of magnitude difference in dislocation density. Dislocation substructures were not significantly different amongst the deformed sample orientations. In contrast, [001] W rods penetrated into steel targets, at impact velocities of ~1.3 km/s, exhibited heavy dislocation densities and dynamic recrystallization as very distinct microstructural regimes accommodating the penetration process. Twinning on {112} also occurred as a precursor to, or remnant of, these microstructures near the projectile head. These results suggest that deformation accommodating the extreme strains and strain rates associated with the penetration of a single-crystal rod into a metal target is not adequately represented by conventional deformation

Jan 1, 2006

By Bill Linville

During fiscal years 1967-68, the Bureau of Mines produced 185 technical papers and reports about petroleum and oil-shale research, which were published either by the Bureau or by others as referable scientific literature. Numerous other reports were prepared for Government agencies, State agencies, and organizations of the petroleum and natural gas industry engaged in cooperative research programs with the Bureau. Research performed during the reporting period by the Bureau on petroleum, natural gas, and oil shale was classified by 71 active projects. A basic appropriation of $3,575,000 was supplemented by $1,300,000 in fiscal year 1967, and that of $4,043,000 by $1,402,000 in fiscal year 1968, making the appropriated-to-supplemental fund ratios about 2.8 to 1 for fiscal year 1967 and 2.9 to 1 for fiscal year 1968. In fulfillment of the mission of the Bureau, through planned research programs, methods for producing and utilizing petroleum were improved. The continued conservation of this natural resource of petroleum, including crude oil, natural gas, and oil shale, was pursued through research performed by some 350 personnel at two petroleum research centers and two petroleum research laboratories supervised and supported by administrative personnel of the Bureau and the Department of the Interior.

Jan 1, 1970

By Michael Gauna

An evaluation and analysis of a coal pillar bump in a West Virginia mine indicated that the pillar bump occurred because of the unique combination of controlling factors. The pillar?s development stability factor of 2.6, based on Mark-Bieniawski strength and tributary loading, would typically indicate an adequate pillar size for long-term main entries. A combination of multiple-seam mining geometry and geological conditions resulted in stress concentration leading to the coal pillar bump. No high extraction mining had been performed in the area and the overlying works appeared to have adequate stability factors. However, it was interpreted that long-term flooding had softened the overlying pillar system and rendered all but the largest pillars ineffective. Contributing factors include large overlying pillars transmitting stress through the approximately 60 ft of interburden and the failed pillar?s location at a transition in the immediate roof from shale to hard, massive sandstone. Other contributing factors include sandstone channeling forcing the development section to mine the pillar smaller than surrounding pillars in an attempt to avoid the channel, the relatively high overburden of 1,100 ft, and the pillar?s position in the bottom of a trough within the coal horizon. Pillars subjected to similar conditions on the other side of the section did not fail where the roof was composed of shale, even though the roof exhibited evidence of high stress concentration. An analysis was undertaken to determine appropriate pillar size for future mining. The conditions were evaluated by investigating mine historical conditions, assessing pillar bearing pressures, and using Lamodel 2D coupled with traditional Mark-Bieniawski pillar strength and tributary area loading stability factors to determine the stress levels for the pillar. Recommendations for future pillar sizes were based on the critical load bearing capacity identified by the analysis. To date, no further pillar bumps have occurred.

Jan 1, 2008

By Milson de Andrade Júnior

A Central Termoelétrica número 2 (CTE#2) possui três caldeiras de alta pressão que utilizam principalmente os combustíveis residuais dos processos siderúrgicos, com destaque para o gás de alto-forno (GAF), o qual está disponível em grande volume e com baixo custo. Como o GAF possui baixo valor calorífico, ele é enriquecido em duas misturadoras com gás de aciaria (GLD) e na ausência ou limitação deste, com gás natural (GN). A partir de 2014, devido a problemas com o gasômetro de GLD, passou-se a utilizar o GN com frequência para fazer o enriquecimento do GAF, o que gerava significativo impacto no custo do vapor devido o alto custo do GN. O sistema de injeção de GN nas misturadoras era controlado de forma manual e praticamente não acompanhava as variações no poder calorífico (PCI) do GAF. Percebeu-se que seria possível implementar um sistema de controle para as injeções que levasse em consideração o PCI do GAF, reduzindo o consumo de GN quando o PCI estivesse mais alto e aumentando o consumo quando o PCI estivesse mais baixo. Após a implementação deste sistema houve uma significativa redução no consumo médio de gás natural para enriquecimento do gás de alto-forno na CTE#2.

Aug 17, 2017

By K. Duckworth

"Comparative tests of the conventional Turam survey configuration and an alternative configuration called the Tx-parallel configuration were conducted at the McClean uranium deposit in northern Saskatchewan. Both configurations detected the known conductors at the site but the alternative configuration demonstrated its particular effectiveness in the reconnaissance role. This effectiveness results from the fact that the length of Tx-parallel traversesis controlled only by the length ofthe transmitter and not by its power. In addition, the field strength along a Tx-parallel traverse is uniform unless the traverse approaches the end of the transmitter. This freedom from a strong gradient of the primary field along a Tx-parallel traverse eliminates the gradient-induced anomaly shifts which are common in conventional Turam operations. The locations of each of the McClean conductors, that were obtained from the Tx-parallel profiles, werein better agreement with the locations known from drilling than were the locations obtained from the conventional profiles. However, the conventional profiles gave better estimates of the conductance of the targets.The results obtained over the McClean conductors indicate that current gathering has a strong influence on Tx-parallel results with consequent unpredictable influence on depth and conductance estimates. However, the depth estimates obtained from the Tx-parallel data appear to be in good agreement with the known depth of the McClean south conductor. The Txparallel results provide shallow estimates of the depth of the McClean north conductor which suggest that the fracture zone above the graphitic conductor is a significant conductor as was also suggested by earlier VLF surveys.Comparison with the wide range of published geophysical test surveys for the McClean site showed that apart from the work required to lay the transmitter, the Tx-parallel mode of operation of a Turam exploration system is operationally very similar to a moving source Slingram type of survey. At the McClean test site, it provided the same depth of exploration as a conventionally deployed fixed loop transmitter."

Jan 1, 1988

Electronic noses are being used in the processing industries and in fields such as environmental and occupational hygiene to detect a wide variety of problems from contaminated foods to toxic chemicals in soils. Recently, research has been conducted into the use of these devices for detecting spontaneous combustion in mines with the aim of producing a method for early detection of a developing heating. Gas samples were collected from both SimtarsÆ 16 m3 large-scale spontaneous combustion reactor and the University of QueenslandÆs two-metre column. The samples were analysed using an electronic nose. GCMS and HPLC were used to identify some of the components present. A number of issues both from a practical mine situation and a scientific standpoint have been identified that need to be addressed before these devices can be used to detect a developing heating. Aluminised bags routinely used in the mining industry to collect gas samples for analysis of the permanent gases are not suitable for use with electronic nose devices as they have a æfingerprintÆ from the polymer lining that interferes with the coal heating fingerprint. Tedlar bags used for environmental gas sampling are also unsuitable due to their fingerprint. Gas samples can be collected in glass gas bulbs with aluminium seals and successfully analysed. However the aluminium foil used to seal the bulbs is a restricted item in underground mines. It was also found that the volatile organic fingerprint of the coal heating was extremely weak at temperatures below 130¦C. Before a useful application can be developed, further investigation into the chemical species present in the off-gases from Australian coals is required.

Jan 1, 2005

By Frank B. Fulkerson

A study was made of scrap iron and steel in the South Central States in order to determine trends in processing, shipment, and consumption if this important commodity. These data were derived in part from statistical sources and in part by visits to scrap yards and steel mills. Trends in the industry were reviewed. Dealers in 1963 supplied 1.8 million tons of iron and steel scrap to steel mills and foundries in the south-central area, compared with 2.1 mill ion tons in 1955. Most of the scrap was processed and shipped within 200 to 300 miles of consuming centers. Exports provide a principal outlet for dealers along the gulf coast. Most of the scrap that fills these orders is loaded onto freight cars at yards in Texas and Louisiana and is shipped to ports for direct transfer from railroad car to ship. The tonnage exported varies greatly from year to year. The largest scrap operations are in or near large cities which are heavy scrap generating areas, steel mill sites, or port cities for export of scrap. A tentative analysis indicates that the short-run supply of prepared scrap is inelastic to price changes; therefore, buyers probably are in a strong bargaining position at times of declining demand. One technological development in the iron and steel scrap industry is the use of large presses which can take complete automobiles with frames, wheels, springs, and other heavy parts still intact and reduce them to bundles. At Houston, Tex., and Kansas City, Mo., shredding plants are in operation that reduce car bodies and other light scrap into flat pieces 4 to 6 inches in size.

Jan 1, 1966

Uranium ore at Sleisbeck, N.T., occurs as lenticular bodies associated with zones of bleached carbonized schists lying between walls of closely folded quartzite. The ore consists mainly of uranium micas with Borne pitchblende.INTRODUCTIONThe Sleisbeck uranium prospect is about 70 miles E. of Pine Creek, and 160 miles S.E. of Darwin (Fig. 1). The prospect consists of a well-defined, E.-W. trending line of hills, about I! miles long. The line is composed of 3 major hills called the Eastern, Central and Western hills, with minor interconnecting hills and outcrops (Fig. 2).

Jan 1, 1955

In blasting large tonnages of ore or material, the economy of the operation &apos;depends mainly on the mine manager&apos;s judgment in placing the holes to the best possible advantage and in determining the most effective size of hole to suit the conditions and requirements.The placing of holes is often looked upon as a problem involving so many uncertain factors that the application of simple mathematics is impossible. The uncertain factors arise when dealing with strata of different character, in hardness toughness and resistance to shearing.A study of the practice at many mines where all types of strata from hard ore to relatively soft overburden, and even coal, is being mined, suggests that the problem is not as complex as generally believed. There is, without doubt, some uniformity in the amount of burden given to holes of equivalent dimensions, regardless of the material being mined. The reason is simple. With too great a burden hard rock will not break out and soft rock will &quot;bull&quot;. The nature of the strata is taken care of by the strength, quantity and distribution of the explosive charge and, to some extent, the spacing of the holes.It is because burdens are uniform in all classes of strata met with in mining, that a formula can be used to design blast hole layouts.The formula introduced in this paper is empirical as it is based on prevailing practice. It has been tested and proved remarkably accurate against every example available to the writer. Many thousands of blast holes, at many different mines, are represented by the examples given in the attached tables; to give further examples would only mean, unnecessary repetition. At the Mount Morgan Mine...

Jan 1, 1952

By J. B. Umhau

During 1928 the United States consumed 73,270 long tons of virgin or primary tin, which was approximately 7.5 per cent more than the 68,198 long tons con¬sumed in 1927 and equaled 41 per cent of the world&apos;s production in 1928 (approximately 178,000 long tons). Consumers&apos; stocks amounted to 9,268 tons on January 1, 1928, and 8,587 long tons on December 31, 1928, a net reduction of 681 tons. In addition to the virgin tin accounted for above, 12,106 long tons of secondary metallic tin were used by manufacturers of tin products in 1928. These figures are the result of an inquiry addressed by the Bureau of Mines to manufacturers to determine the amount of metallic tin used by them; in reply, 1,307 establishments reported consumption in 1928. The distribution of the amount consumed by various uses, as shown in the allowing tabulation based on Bureau of Mines canvasses for 1927 and 1928 in comparison with consumption by uses reported by the War Industries Board for 1917, emphasizes the fact that new uses for tin have been developed in only minor or insignificant amounts. Furthermore, although the studies for recent years show that some older uses have been discontinued, the amounts involved were all small and insignificant. Variation in consumption from year to year parallels the fluctuations in demand for the already well-established tin products. For example, the manufacture of bearing metals and solders for motor cars and trucks required 19,000 tons in 1928 compared to 16,000 tons in 1927; the canning industry continues to require the greater portion of the tin plate and also much solder. Growth in the electrical and the more recently developed industries (aeroplane, refrigerators, radio, etc.), while affecting total consumption of bearing metals, solders, etc., has made little change in the proportions required for these basic methods of using tin.

Jan 1, 1929

By Victor Costa de Mello Vasconcelos

O objetivo desse projeto é a preparação nanofolhas de óxido de níquel por calcinação e a formação de híbridos com nanopartículas esféricas de ouro e paládio. O trabalho focou na síntese de materiais com forma e tamanho controlados por meio de metodologias simples e ambientalmente amigáveis e na preparação de estruturas híbridas com dispersão uniforme entre componentes. Foram obtidos hidróxidos, óxidos e híbridos, cujos parâmetros de síntese (como temperatura, tempo de reação, entre outros) foram estudados. Uma vez caracterizadas, empregaremos as estruturas do tipo M/NiO (M = Au, Pd) como catalisadores nas reações modelo de oxidação do álcool benzílico e de redução do 4-nitrofenol, com o intento de estudar a natureza da interação metal-suporte.

Oct 30, 2017