Search Documents

By Holger Witthaus

There is more than a century of experience in multiple seam mining in Germany. In several mines up to 20 seams had been excavated within the last decades. Due to the nature of the deposit and the history of technical development the older panels cause a complex stress distribution for the lower seams and the current longwalls in descending order of mining. The depth of the longwalls reaches up to 4000 ft. This causes a maximum vertical stress that reaches between 30 and appr. 60 MPa. To handle these conditions several support systems are applied for roadway heading. A central knowledge management system for ground control is used for design and dimensioning of support within the DSK. This paper gives an overview to the nature of German multiple seam mining and the solutions in matters of panel layout and support design. It describes the full lifecycle for roadways in the seam starting with the geological and geotechnical evaluation, the basics of roadway deformation in great depth, the development of planning tools and standards for German coal mines, the range of alternative of support systems and roadheading techniques, as well as the reinforcement measures and the processing of support at the T-junction of the face entry. This paper uses exemplary descriptions that are consolidated in a specialized reference book ?Gebirgsbeherrschung von Flözstrecken? ? ?Ground Control in Roadways? which summarizes the standards of ground control based on the development of the past 25 years in German coal mines.

Jan 1, 2007

By Patrick Cloutier

Presentation objectives ? Introduce discrete-event 3D computer simulation as a tool to design, improve and optimize construction projects: ? Describe a real typical construction project planning issue. ? Present an applied use of simulation to solve this issue. ? Detail benefits of using simulation versus traditional planning methods.

Aug 1, 2013

By Peter Zhang

The immediate roof at the test site consisted of laminated clay shale that is likely to be susceptible to weathering. With seasonal dry-wet cycles in the mine ventilation air, the roof in the intake air would deteriorate and lose integrity over time. In many instances, the weathering-prone roof would gradually scale off piece by piece between bolts and over the entry corners. In some long-term entries, roof weathering could develop up to 2-3 ft deep with columns of bolted roof hanging under the upper intact roof. If wire mesh is used, the roof bags down and reduces the entry height, and the weight of the bagged roof tends to pull the bolts out and poses a safety hazard. An effective measure is always sought to support this type of weak roof that is sensitive to moisture degradation. One solution is to seal the roof shortly after entry development to prevent moisture penetration so that roof integrity can be maintained for the long term. In this application, a polymer-based sealing material was tested in the Rockspring mine for weathering protection and reinforcement. The material is a one-component polymer powder for spray application onto the roof and rib. The sealant material is mixed with water in the spraying nozzle to apply to the roof and rib as a paste. The product sets within 5-10 minutes and forms a membrane as thin as about 1/8-in. The membrane will quickly develop tensile and bonding strength within minutes and completely cure within a few days. Through sealing, bonding and lateral reinforcement, the integrity of the weak roof can be maintained. The material has been tried in a long-term evaluation over several months in a set of main entries in the Rockspring mine owned and operated by Rockspring Development, Inc., affiliate of Foundation Coal. Preliminary evaluation has shown that the material is an effective and economical solution to ensuring the long-term stability of weathering-prone roof.

Jan 1, 2009

By Charles H. Jacoby

The solution mining of evaporites has a history of approximately 5,000 years. The insitu leaching of metalliferous ore will have many of the same characteristic problems which have confronted industry for years in the production of evaporite minerals. Basically we will be converting the less soluble forms of valuable metals into their more soluble salts and producing these in much the same manner as, for example, sodium chloride. There are a number of problems which we are faced with that are more complex and complicated and, therefore, will require a higher degree of sophistication than previously employed. One of our most important undertakings will be the clearcut definition of the problems involved. While a great deal of expertise can be drawn from the solution mining of evaporites and the oil industry, problems peculiar to the hydrometallurgical field will need to be solved. One of these is the introduction of permeability into an impermeable rock so as to expose the sought after values of metals which by volume are infinitesimal when compared with sodium chloride, potash or other type water soluble mineralization. After establishing this permeability which will be miniscule when compared to a solution cavity, there will be the maintenance of this permeability. In general, salt deposits are of a somewhat uniform chemical composition and thus their chemistry was relatively simple. Each metalliferous ore body is somewhat unique in its chemistry and will need to be treated accordingly.

Jan 1, 1974

By G. I. McPhail

The authors have conducted several investigations into the prediction of the beach profile of high-density tailings and have found that there are a number of important considerations that need to be taken into account over and above the reliability of the beach profile prediction methodology. These considerations relate to the chemistry of the slurry and specifically the influence of pH and flocculation, both of which have a significant influence on the rheology of the slurry at the discharge point. A number of examples are discussed and a potential testing protocol that will assist in assessing the influence of chemistry ahead of the beach profile predictions is presented. A methodology for assimilating the results of the testing into the likely field situation is discussed, and suggestions are made on application of the results in beach profile prediction. The suspected influence of residual flocculation on the stratification

Jan 1, 2012

By P. R. Dugan

Sulfur removal from high sulfur coal has several objectives including: a) reduction of the atmospheric load that contributes to the problem of acid precipitation; b) reduction of ash, which contributes to decreased energy transfer in boilers, as well as ash disposal; and c) alleviation of the social and economic dislocations reluted to uneven geographical distribution of sulfur in coal reserves. Cost in relation to the value of refined coal will govern the development of an emerging coal refining industry. Estimation of the premium paid by power companies for coal with a low sulfur content is a good estimate of the value that will be added as the result of refining. Estimates of premiums paid in 1984 are $28.65/t ($26 per st) for reduction of total sulfur from 3’% to 1% S and greater than $28.65/t ($26 per st) for removal below 1% sulfur.

Jan 8, 1987

By Dennis R. Dolinar, John L. Ellenberger, Gabriel S. Esterhuizen, Anthony T. Iannacchione

A survey of pillar conditions was carried out at 21 operating limestone mines that use the room-and-pillar method. The surveyed pillars were all located in rock that was classified as “Good” to “Very Good” using the RMR rock mass classification system. The average pillar width was 14.5m and the width to height ratio varied between 0.53 and 3.52. Pillar conditions were rated using a visual rating system that accounts for the effect of geological structures as well as stress related fracturing. Nine cases of pillar instability were recorded. Pillar instabilities were typically limited to individual pillars or small groups of pillars within an otherwise stable layout. Local geological structures such as inclined discontinuities or weak bedding planes contributed to instability in seven of nine cases that were observed. Elevated pillar stresses contributed to instability in the two remaining cases. All the unstable pillars observed had width-to-height ratios of less than 1.5. It is concluded that pillar instability is most likely to be caused by unfavorable geological structures in pillars with width to height ratios of less than 1.5. Stress related instability such as rib spalling becomes more prevalent when the average pillar stress approaches approximately 20 MPa.

By Sandra Lúcia de Moraes

O presente trabalho visou contribuir para o melhor entendimento do mecanismo inerente ao uso de agente coloidisante/dispersante no processo de pelotização de concentrado de minério de ferro. Avaliou-se a influência dos agentes coloidisantes em comparação aos aglomerantes Peridur e bentonita. Para este fim, foram realizados ensaios de bancada visando a identificação de possíveis ações destes agentes no grau de dispersão das misturas, bem como a sua influência na liberação/aglomeração dos finos. Os resultados destes parâmetros foram confrontados com os resultados de caracterização das pelotas confeccionadas com os diferentes agentes pelos quais foi possível identificar que os dispersantes tem forte atuação sobre o conteúdo de finos do concentrado de minério de ferro. A ação principal se dá pela remoção das partículas ultrafinas que recobrem os grãos mais grosseiros presentes na amostra e as dispersam, no caso dos dispersantes, aumentando a disponibilidade do conteúdo de finos <4 µm, principalmente os finos <1 µm (coloides). No caso do aglomerante orgânico, observa-se também essa ação, no entanto, os finos presentes são aglomerados na faixa entre 26 e 4 µm.

Aug 16, 2017

By S. Vézina

"Environmental issues have evolved considerably over the last two decades. The main contributing factors, to name a few, have been the changing values of modern societies, the globalization of trade and its linkage to environment, evolution and accessibility of information/ communication technologies, better educated populations, climate change, longrange transport of toxics, and the increasing influence of non-governmental organizations (NGOs) and multistakeholders.As well, environmental management of mining operations had to be realigned in order to meet these new realities and to respond to more elaborated regulations oriented towards sustainability. Environmental management systems (EMS) have been introduced not only to meet the assurance of conformance to regulations but also to prevent pollution and to apply the continuous improvement of mining processes. EMS models have been developed and certification to international standards (e.g. ISO 14 001) is a common practice.Globalization has imposed challenges and additional requirements to environmental management. Developing a mine in emerging countries implies dealing with international agencies, local communities, and a variety of government infrastructures to obtain a “license to operate.” This paper presents the structure of Cambior’s EMS and how it was adapted and implemented in the company’s operations in South America."

Jan 1, 2006

By M. K. Larson

The U.S. Bureau of Mines conducted a study to evaluate support interaction between conventional bolts and the rib at two Western coal mines. The principal goal was to develop guidelines for designing rib support under various conditions. At mine A, seven rib bolts were installed with load cells and monitored over a 4-month period. Fifty-seven pull tests were conducted with two types of anchors at various depths. At mine B, 163 pull tests were conducted. Results showed that during the 4 months of monitoring bolt load, tension in the bolts decreased over time in some situations and that anchorage capacity was reduced in a yielded zone. Load-versus-deformation plots from pull tests in the rib showed fundamental differences in anchorage behavior at the two mines, particularly when comparing results of tests in old pillars at mine A and tests in new ribs at mine B. Numerical modeling experiments indicate that coal bonding strength was the most significant factor in determining postyield anchorage capacity. Correlation of anchor yield point with anchor depth were more pronounced at mine A than at mine B; measuring torque may be a reasonable method of monitoring deteriorating anchorage capacity in a rib undergoing fracturing and yield.

Jan 1, 1996

Laboratory scale equipment was developed to recover zinc as oxide fume from granulated lead blast furnace slag. The cyclone furnace process is characterised by high treatment rates combined with continuous and independent operation.Results were sufficiently encouraging to warrant pilot plant scale trials being undertaken.INTRODUCTIONSince granulation of lead blast furnace slag started at Port Pirie in 1921 the stockpile of this material has increased to nearly 5 million tons which averages 17·5 per cent zinc by weight. Although a number of processes for recovering the zinc have been examined, economic considerations indicate that a slag fuming process is likely to be most suitable.In the conventional slag fuming process zinc is extracted by injecting pulverized coal and air into a molten slag bath. By maintaining a suitable air to coal ratio the oxidised zinc contained in the slag is reduced to metal. Volatilization of the zinc is followed by reoxidation in the gaseous phase with the addition of further air above the bath. The zinc oxide fume so produced is collected by normal gas cleaning methods.By examination of the thermodynamics of this process Bell, Turner, and Peters (1955) determined the zinc oxide activity of the slag over the duration of the fuming cycle.A combination of high temperature and high carbon monoxide/carbon dioxide ratio was found necessary for rapid zinc elimination.Since melting of the slag is an essential step in the slag fuming process, only two treatment methods appeared possible at Port Pirie until recently...

Jan 1, 1964

By J. L. Morning

During recent years, the Bureau of Mines has conducted an extensive investigation of the materials for making iron and steel. This work includes iron ore concentration, agglomeration, direct reduction of iron ores and concentrates, the production of pure manganese, chromium, and cobalt by electrolytic processes, the production of ferroalloys from low-grade domestic ores, and the development of special alloys to utilize these products. As a part of this general program, a Congressional appropriation allowed the con¬struction of an electric-furnace, semicommercial, ingot-producing plant at Shasta Dam near Redding, Calif. The primary objectives of the pilot plant were to determine the costs and operating problems involved in the production of steel and ferrous alloys in which sponge iron was used as melting stock, and to determine the physical properties of the materials produced. The pilot-plant equipment and the results of sponge iron-melting tests in the basic lined, electric arc furnace have been reported in previous publications.3/4/

Jan 1, 1953

GENTLEMEN, lt is with much pleasure I meet you tonight at this the second meeting of the Australasian Institute of Mining Engineers, held in Western Australia, and I sincerely thank you for the honour you have conferred upon me in electing me as your President. I greatly appreciate the distinction, and will endeavour to fulfil the duties of the office to the best of my ability, and hope to prove a worthy successor to those gentlemen who have held the position before me. On behalf of the local members of the Institute, I extend a hearty welcome to the members from the other States of the Commonwealth, who have come so far to attend this meeting, and also to the non-members whom we have invited this evening. We are especially pleased to have Mr. Gregory, our Minister of Mines and Railways, and the Government and School of Mines officials with us; and I take this opportunity to thank the Premier, Mr. Gregory, and the Government officials for the assistance given us, and for doing so much to make the visit of our members from the other States so pleasant and instructive. I have also to thank the Mayor and Councillors of Kalgoorlie for the courtesy and hospitality given to our members, which is much appreciated.I assume you want me to follow the time-honoured custom of giving a Presidential address...

Jan 1, 1909

By F. T. Cawood, M. A. Jooste

This paper describes the survey monitoring processes at Venetia, which are discussed under visual inspections, ad hoc investigations, system monitoring and slope stability radar monitoring. This is followed by a description of the main survey monitoring methods. The next section briefly states typical problems, i.e. the atmospheric corrections required to adjust total station distances, maintenance of the system and management of the monitoring process. The paper ends with some important lessons that could be applied to similar monitoring programmes. These lessons are firstly, communication is most important, process a vital part of the system, a champion must take responsibility for the programme and system planning ensures that the monitoring results are needs driven.

Jan 1, 2006

By Narasimhan K. S, Sastri S. R

A typical high silica low grade magnesite from the Salem area of Southern India, was used in studies to develop a suitable flotation system involving commercially inexpensive sodium oleate as the collector together with other reagents which can give a product of the required grade with an acceptable recovery. It was found that the presence of metallic ions such as Cu+, Fe+++ or Ca++ introduced by the addition of their salts, or by their formation with the addition of hydrochloric acid to react with magnesium and calcium carbonate in the me, can act as effective depressants for silica. The addition of 'hydrochloric acid' was found to give best results.

Jan 1, 1980

By Robert C. Horton

The Getchell Mine is located on the east flank of the Osgood Mountain Range in the Potosi Mining District, Humboldt County, NV. Mining in the area first began in 1883 for copper, lead and silver in skarn-related deposits. Tungsten was discovered in the skarns in 1916 and was mined sporadically until 1957. The first major discovery was made in 1933 when two Winnemucca prospectors, Edward Knight and Emmett Chase, found gold at the present site of the Getchell gold mine. In 1934, after a small amount of preliminary prospecting, the claims were purchased by Noble H. Getchell of Midas, NV. The Getchell Mine Inc. was organized and exploration and development work began on a broad scale. Major funding was provided by George Wingfield and investors he assembled. Laxalt described Wingfield’s immediate history prior to his financing of Getchell as follows.

Jan 1, 1999

By Kenneth Gavin

The accurate prediction of the shaft capacity of drives piles in sand continues to present problems for foundation designers. Research in this field has been carried out for many years and has yielded a wide range of design approaches -some of which have been shown by recent experimental work to be based on questionable assumptions. This Paper reviews some of the current popular design methods for piles in sand in the context of recent information obtained from high quality field tests conducted by institutions such as Imperial College London. A database of driven piles in cohesionless soils has been compiled from well documented (and reliable) case histories that have been reported in the literature. The measured shaft capacities of the piles in this database are compared with predictions made by the various methods and an assessment is made of the predictive performance and reliability of each method

Jan 1, 1996

By Lei Pan, Venkata Atluri, Xuming Wang, Yuesheng Gao, Jan D. Miller

The wetting characteristics and water film stability at the talc surface have been studied, particularly the effect of polysaccharides such as guar gum, starch, and dextrin. Talc is a gangue mineral in the flotation of base metal sulfide ores, precious metal sulfide ores, and platinum group metal (PGM) sulfide ores. Talc surfaces were investigated using surface analysis techniques including atomic force microscopy, high-speed video bubble attachment measurements, and wetting film stability measurements using a synchronized tri-wavelength reflection interferometry microscope (STRIM). In the presence of polysaccharides, there is a significant increase in bubble attachment time at the talc surface, but only a slight change in contact angle, which suggests that polysaccharide depression of talc is due primarily to the slow rate of bubble attachment and not due to a change in contact angle. The critical rupture thickness (hc) for a hydrophobic talc surface was found to be 56 nm, while the hydrophilic phlogopite surface of similar structure has an equilibrium film thickness (he) of 25 nm. At low polysaccharide concentrations, the wetting films formed on the talc surfaces were unstable, but at high concentrations the wetting films became stable with similar thickness values as the critical rupture thickness, and bubble attachment did not occur. However, it was found that the critical and equilibrium film thickness values do not change significantly with the polysaccharide type or concentration. The results from this research help us understand further details of film rupture and displacement during bubble attachment.

By Arnold M. Lansche

[Selenium and tellurium are rare elements in the earth's crust. Their scarcity and primary dependence of supply on copper and lead output are in consonance with the relatively small quantities consumed at 1964 level. Production depending on output of copper and lead creates a supply situation- which would appear to militate against development of large-scale usage of these elements. However, supplies have adequately met. demand in the past decade and can be increased substantially if warranted by new uses for either selenium or tellurium Ores of copper and lead re the principal sources of selenium and tellurium. Byproducts from the smelting and refining of copper and lead concentrates are incorporated in refinery anode slimes from which selenium and tellurium metal are recovered.]

Jan 1, 1967

By Gaulton R

The Commission maintains a data base first computerised in 1957 and containing information from over 18 000 boreholes located mainly in the Latrobe Valley area. Some of the borehole derived information dates from the turn of the century, although most of it has been collected as a result of Commission investigations conducted over the past 40 years. The Resource Data Base contains not only information gained directly from the drilling itself but includes the results of chemical and physical testing on many hundreds of thousands of samples retrieved from boreholes. Replacement value of the Resource Data Base has been estimated to be around $200 million, and it's integrity and accessibility is clearly of paramount importance, not only to existing mining and power generating functions but to the future evaluation and use of the vast brown coal Resource.

Jan 1, 1992