Search Documents

By Franziska Wolf, Rainer Ellmies, Helmut Mischo

"Mining is an important part of the economy of Namibia. In 2016, 11.1 percent of the GDP was the result of mining activities with 22 active mines (The Chamber of Mines of Namibia, 2016). Only one of them consists of an underground mining operation.The global annual production of fluorspar is approximately 5.4 to 6.3 Mt (6 to 7 million st) (U.S. Geological Survey National Minerals Information Center, 2017). Okorusu has produced on average about 45 kt/a (50,000 stpy) in recent years (U.S. Geological Survey National Minerals Information Center, 2015).The Okorusu Mine is Namibia’s only fluorspar mine. Fluorspar was mined in an openpit mine with four individual pits (A-D) since 1980. In 2014, the mine closed due to the increased stripping ratio and beneficiation problems. The mine assets were bought by Gecko Namibia. Currently, Gecko uses parts of the processing plant for beneficiation of graphite from a neighboring mine. Figure 1 shows a panoramic view with the four pits and the mine village.The intent is to develop a concept for the further underground development of the mine. There are still about 6.3 Mt (7 million st) of measured resources left in the deposit, with an average grade of 27.5 percent CaF2. This study focuses on the underground mine design. The above-ground plant and facilities are considered as remaining unchanged.For solving the task to design the mine, a site visit for data collecting was conducted. Resource estimations were calculated based on existing drill data, and consequently, block models were created. The development of the mine design included the selection of the most suitable mining method, mining technology and mine organization. Moreover, some economic considerations are pointed out, followed by a profitability assessment."

Jan 2, 2018

By F. N. Kissell

U.A. Mine Safety and Health Administration (MSHA) coal dust compliance data sometimes shows high silica levels at roof bolters. However, it is unclear whether this silica normally originates from the bolter itself or from other dust sources upwind of the bolter research studies to answer this question at individual mines have been conducted. However, operational practices vary from mine to mine thus, the information gleaned from any one study cannot be accurately extrapolated to describe silica dust sources in most mines. In this paper, three decades of bolter dust research are reviewed the results showed that, while inadequate maintenance on the bolter dust collection system can result in excessive dust, more likely reasons for high silica levels are inadequate ventilation of the mine entries being bolted and dust traveling downwind from the continuous miner to the bolter. Scrubbers on continuous miners may not be removing as much silica dust as expected. Mining Engineering, 2011, Vol. 63, No. 10, pp. 78-82. Official publication of the Society for Mining, Metallurgy and exploration, Inc.

Jan 1, 2011

By Robert C. Laudon

Spectral reflectance data for 335 minerals, including 228 minimum-maximum combinations for anisotropic minerals giving a total of 563 data sets, have been collected from the literature and combined into a single database. Quantitative color values for x, y, Y, Ad , and Pe referred to ICI standard i11uminant C have been calculated from the spectral reflectance data and are included in the database. The programs plot spectral reflectance curves together with all quantitative color data for each mineral in the database. The plots and data can be directed to a dot-matrix printer such that a databook of quantitative color and spectral reflectance having one mineral per page can be generated for the ore microscopy laboratory. In addition, by sorting the database and grouping the minerals, groups or individual minerals can be plotted on the chromaticity diagram, and this plot can also be sent to a dot-matrix printer. The programs are written in compiled BASICA for an IBM-PC with graphics capabilities and at least 128KB random access memory (RAM). The databases are accessible either through the BASIC programs or through any commercial database system capable of loading and writing to an ASCII format sequential file. The programs and database are available by sending a blank diskette and self addressed, stamped envelope to the authors.

Jan 1, 1987

By P V. A van der Westhuyzen

Namakwa Sands is a heavy minerals mining and beneficiation business in the Exxaro Sands Division, and operates along the West Coast of South Africa (see Figure 1). The business encompasses mining, mineral concentration, separation, and smelting operations. Inflated commodity prices and increasing operating costs demands greater attention to the management of process performance and the company wide coordination of resources. Consequently, the task of deploying operational/technical skills and budgets into the most appropriate parts of the business assumes great importance in order to increase productivity from its capital assets. The mineral sands industry is under the same sort of economic scrutiny that all other industries find themselves, and as such, Exxaro – Namakwa Sands has taken the strategic initiative to improve overall resource utilisation within the processing steps and to measure the costs associated with obtaining this value.This paper provides details of the successful implementation of a Kelsey Centrifugal Jig (KCJ) at Namakwa Sands to recover primary and secondary zircon products from the wet gravity (quartz) rejects generated and stockpiled at the Mineral Separation plant (MSP).

Oct 5, 2011

By C Delwig

ThyssenKrupp specialises in the manufacture of high-grade steel-sheet products. Its main customers include the automotive, construction, household appliance, energy and packaging industries.At its works in Duisburg, Germany, ThyssenKrupp Steel Europe produces 12 Mt of crude steel annually, making Duisburg one of the world’s largest steel hubs.ThyssenKrupp have installed an online elemental analyser and limestone dosing control System on one of three Sinter strands at Duisburg in an attempt to control the sinter raw mix with better precision. Traditionally, set point changes to the raw mixture were made after sampling and laboratory analysis of the sinter product. The analyser chosen uses prompt gamma neutron activation analysis to determine the elemental content of moving material on a conveyor each minute and was supplied by Thermo Fisher Scientific. The project goal was to control the CaO/SiO2 ratio (basicity) and reduce its variability in the sinter feed.Evaluation of the system has shown that the addition of the online analyser reduces the time lag related to the former method, therefore upset conditions can be reacted more quickly by the control system, and this has resulted in a more stable sintering process. As a result, the sinter feed variability in case of the basicity has been reduced by half. While CaO/SiO2 control was the initial aim of the project, a number of other benefi ts have been realised, such as a reduction in return fi nes and a financial benefi t of 0.11 €/ton of sinter attributed to the reduction of coke breeze and limestone. ThyssenKrupp Steel Europe has identifi ed that additional information available from the analyser could be used to optimise the complete sinter process.The project was carried out with a financial grant of the research program of the ‘Research Fund for Coal and Steel’.

Jul 11, 2011

Dado que la industria metalúrgica peruana está a la vanguardia de la modernidad, en tanto actualiza sus conocimientos -a través de diversos congresos mineros-, como difunde el uso de nuevas máquinas de concentración de minerales- el objeto del presente estudio describe el problema de los operadores en las plantas de concentración del Perú. En este aspecto, es importante el uso de dichos equipos en el tratamiento de minerales puesto que extraen el máximo de su valor y reducen mínimamente su fundición en el país y el extranjero. Sin embargo, su buen funcionamiento no se limita a una óptima estructura del los equipos, o por la resonancia de su empleo, sino que responde a los operadores de plantas. Durante mucho tiempo,la mayoria de personal empleado en esta labor, se rehusó a trabajar con tales equipos dado sus hábitos, y si lo hacían era más una cuestión de aceptación que de propio conocimiento, tornándose la máquina, como algo secundario. Ante esta situación, se buscó formas de superar dicho problema a través de la enseñanza de los entrenadores, como del interés del trabajador, obteniéndose óptimos resultados en poco tiempo.

Jul 20, 1957

By N. Campbell, W. T. Orvine

The metalliferous deposits of British Columbia are largely confined to that portion of the Cordilleran province lying west of the Rocky Mountain trench. Massive sulphides in the coastal area carry important copper •values together with lead and zinc and are composed mainly of pyrite which replaces schists or shear zones. The massive sulphide ore of the interior, on the other hand, contains lead and zinc with little copper. Pyrrhotite rather than pyrite is... the dominant metallic and deposition took place through selective replacement of sedimentary beds.

Jan 1, 1960

By D. F. Boyd

On April 10, 1958 a new 7500 long ton/day iron ore beneficiation plant went on stream producing an average of 3000 long-tons of high quality concentrate a day. Plant operates on two, 12-hour shifts is six days per week, The new mill end crust ink plant were built adjacent to the company's open pit dining operate on at Bomi Hills, Liberia. The mall is essentially a gravity concentrator employing crushing, and grinding to liberate the mineral values, followed by concentration in Humphreys spirals. The cleaner spiral tailings are re-ground and tabled to recover additional iron values. Ire addition to. this mills the company operates a crushing and screening plant for the high grade direct shipping ores

Jan 1, 1962

By Paul T. Allsman

The vanadiferous deposits of the Sublette Ridge and Salt River Range, 2 miles east of Raymond, Idaho, in western Lincoln County, Wyo., were examined August 24 to August 30, 1942, by an engineer of the Bureau of Mines, who was shown these properties by W. W. Rubey of the Geological Survey, Washington, D. C. The Sublette Ridge deposits are owned by the former U. S. Phosphate Co. H. F. Chaney, Portland, Oreg., is the representative for the company. The following report covers the history of the district, outlines the physical features and communications, mentions the property, and notes the ownership. The deposits and ore are described, and work performed by the Bureau of Mines is explained in detail. Ore-dressing tests and methods are explained.

Jan 1, 1949

By Owen Matthews

THE property of Cochenour Willans Gold Mines, Limited, is in Dome township, Red Lake area, northwestern Ontario, a hundred miles north of Kenora and close to the Manitoba border. 'Planes of Canadian Pacific Air Lines, Limited, serve the district daily, except Sundays, from Kenora, Ontario, and Lac du Bonnet, Manitoba, passengers being trans-ported from Winnipeg to Lac du Bonnet by car. Freight is handled by the Patricia Transportation Company. It is brought in from Hudson, Ontario, on the Canadian National railway, in summer by water and in winter by tractor trains over the frozen lakes. The first staking on the property was done during the 'rush' of 1926 and 1927 by William M. Cochenour, and on April 30th, 1928, a syndicate was formed, taking in claims of W. M. Cochenour and Dan Willans and H. G. Young. Surface trenching was carried on almost continuously until 1934. In October, 1932, Ventures Limited took an option on the property, and in December of that year they carried out an extensive diamond drilling programme, but considering the results did not justify further work, they relinquished the option. In July, 1934, further surface work was carried out under the supervision of W. P. Mackle and, on the strength of his report, Noah Timmins Incorporated took an option on the property and agreed to make an initial expenditure of $100,000 on development work. This was carried out under the direction of Hollinger Consolidated Gold Mines and included the sinking of a shaft to a depth of 165 feet, establishment of a level at the 150-foot horizon, and some 1,900 lineal feet of drifting and cross-cutting. The results obtained from this work were not considered of sufficient promise and the option was terminated in August, 1935. Mr. Cochenour then approached Alex Mackenzie and associates, and the present Company, Cochenour Willans Gold Mines, Limited, was organized on April 9th, 1936, and sufficient money was raised to continue operations. Under the direction of W. P. Mackle, the shaft was deepened and a second level was established at the 275-foot horizon; but, due to several adverse reports by outside engineers, it was found impossible to raise sufficient money to carry on the work and operations were suspended in December, 1937. In January, 1939, an agreement was entered into with Gold Eagle Gold Mines for the milling in their plant of some Cochenour ore. A total of 4,959 tons was treated, and the results were so encouraging that further finances were raised by C. A. Gentles & Company, of Toronto. Following further development in the mine, it was decided to erect a mill. Construction was started on September 1st and the mill was turned over on November 29th. The first gold brick was poured on December 23rd.

Jan 1, 1942

By William W. Odell

Certain gas-making processes are in use in Europe, particularly in Germany, which differ radically from those in common use in America. A number of them are of particular interest because they are different. The questions naturally arise: Are any of them applicable to the making of gas in this country and, if so, with what particular type of solid fuel? It is a fact that some of them were developed with consideration of a particular set of conditions and for the utilization of solid fuels available in Germany. The latter fuels, in certain characteristics, are unlike the high-rank fuels commonly used for making gas in the United States; therefore, in attempting to evaluate the various foreign- developed processes with regard to usefulness here, one must give attention to the particular conditions that will prevail in any specified case and also the characteristics and requirements of the process and generator under considera- tion. Three of the processes that were developed and put into commercial operation in Germany, and which have some characteristics in common, are con- sidered in particular in this publication; they are: 1. Lurgi pressure gasification process. 2. Winkler process. 3. The Leuna slagging-type producer-gas process. Each of these processes requires steam and oxygen as gas-maiding fluids. For a number of years, oxygen, has been used in a relatively pure state,. along with steam, in making gas in Germany, and many of the difficulties initi-. ally encountered have been overcome. Although it appears that oxygen recovered from air was first used in this manner as a method of utilizing a byproduct in a plant that used the nitrogen complement in the manufacture of ammonia; more recently, the oxygen was made particularly for the purpose. The fuels - brown coal or lignite used in processes 1 and 2 were not suitable for use in the older and commonly used intermittent-type water-gas generators, and it was necessary, therefore, to devise a different process for gasifying them. A gas of higher heating value than producer gas, was desired, and the use of oxygen (not air) along with steam made possible the production of the desired gas without nitrogen dilution, which characterizes producer gas. Operating data presented herein are based upon observations by, members of the Technical Oil Mission at plants in Germany, on records, and on information vocally given to members of the lässion, including the author, while visiting those plants, and they are believed to be reasonably correct; however, certain hasic observations, comparisons, and conclusions are. made by the author.

Nov 1, 1947

By E N. Sparg, O D. A Deuchar, F Needham

Decline shafts are an attractive option to both new and existing mining operations where there is a need to access an inclined orebody deposit via on-reef development so as to generate a return in the shortest possible time. There are many different technologies that are available to transport men, material and rock in incline shafts. This paper focuses on the applicability of two hoisting technologies for decline shafts, namely endless and direct rope systems. The pros and cons of each system are reviewed. A common concern with direct rope haulage systems is the possibility of generating slack rope during deceleration. This paper illustrates the issues involved in designing a system so as to avoid the possibility of slack rope. In conclusion, the key factors relevant to the selection of endless or direct rope haulages for a particular decline application are reviewed. The paper is a joint submission by FFE Minerals-Vecor and Qualter Hall UK.

Jan 1, 2005

By W. G. Mine

In September, 1953, seismographs were installed in the Crowsnest Pass area of Alberta and British Columbia to study the 'bumps' which were occurring in the coal mines at Fernie and Coleman, and to investigate the possibility that they might be related to minor earthquakes in the area. During the initial phase of the work, three seismographs were operated at widely separated stations, two in the region of coal mines at Coal Creek and Coleman and one at Turner Valley, distant from any mining operations. Some earthquakes were recorded at all three stations and, in addition, many small disturbances were recorded by the seismographs located near the mines, especially -by the instrument at Goal Greek. A closer network of radio-linked seismographs was then in-stalled near Fernie, the records of which definitely established that the small disturbances were occurring in the mine workings, both active and inactive. No relationship was established between bumps and local earth-quakes in the area. This work was initiated as a -co-operative effort with the Fuels Di-vision of the Mines Branch, Department of Mines and Technical Surveys, which has undertaken a study into the phenomena of ground stress relief in underground mine workings.

Jan 1, 1958

By H. Kenworthy

The investigations described in this report were undertaken to demonstrate, on a laboratory scale, the possibility of recovering several million pounds of tin plus tungsten contained in stockpiled and currently rejected slags from the Longhorn tin smelter at Texas City, Tex. At the same time, it was anticipated that the treatment procedures developed might be applicable to slags from other tin-smelting operations. Results of the laboratory work show that it is possible, by pyrometallurgical means, to separate the tin and tungsten into products of intermediate grade that may be returned to the smelter circuits for further upgrading. Several methods of treatment were investigated. The methods that proved effective were: Fusion reduction, chloride volatilization, sulfide volatilization, and carbide formation. Over 90 percent of the tin and tungsten could be removed from the slat by any of these methods. Each type of treatment has advantages and disadvantages, and it could not be determined from the small-scale work which method was the more meritorious. Tungsten and (in some types of treatment) tin-bearing products were diluted by iron, the separation of which will require additional studies. Prevention of a portion of the iron from reporting with the tin or tungsten is a distinct advantage and possibility that will require inure laboratory work to develop the needed techniques for its accomplishment. Tin products from single treatments of stag ranged up to 75 percent in tin content but were more generally under 35 percent. Tungsten products were usually under 15 percent; but segregated portions could be selected, at a sacrifice in recovery, that contained up to 50 percent tungstic oxide equivalent.

Jan 1, 1957

By D. Botha, J. F. Cronjé

"SynopsisAlthough women all over the world have been involved in mining activities for centuries, mining has always been considered a very masculine industry due to its heavily male-dominated workforce as well as the physicality of mining work. The mining industry has not been an obvious career choice and preferred place of employment for women; women were mainly employed in administrative and advisory positions. Until 1994, women were legislatively prohibited from being employed in underground operations in South Africa, but the Mines Health and Safety Act, No. 29 of 1996, removed these restrictions. In addition, new mining legislation (the Mineral and Petroleum Resources Development Act, No. 28 of 2002) and the accompanying Mining Charter make specific provisions for the inclusion of women in core mining activities and require 10% of core positions to be filled by women.This article voices perceptions of the physical ability of women employed in core mining positions. Findings are drawn from empirical work undertaken at platinum, phosphate, and copper mines. Quantitative and qualitative research paradigms are used. It is evident that women find it extremely difficult to perform mine work that requires physical strength and stamina. Practical recommendations, informed by the literature review and empirical findings, are made with the objective of contributing to the sustainable deployment of women in the mining industry.IntroductionFor many years, mining has been considered the foundation of the South African economy. Although the mining industry in South Africa is currently under considerable pressure and experiences various challenges, including escalating operational costs, electricity tariff increases, safety-related issues and associated production stoppages, poor productivity, labour unrest, and reduced demand both globally and domestically, it remains a key contributor to the national economy and development of the country (IDC, 2013, p. 9).Until 1994, women were legislatively prohibited from meaningful participation in the mining industry and were denied access to skills and jobs, self-employment, and entrepreneurship. The newly elected democratic government in 1994 initiated substantial socio-political and economic transformation in South Africa. Nearly every sector in the country was transformed and re-shaped, primarily through sector-specific legislation, but also through negotiations between government, industry, and labour unions to create and refine the so-called sector charters, which included the Mining Charter. The vision of the new regime, the African National Congress (ANC), was to ‘transfer power to the people and transform society into a non-racial, non-sexist, united, democratic one, and change the manner in which wealth is shared, in order to benefit all the people’ (ANC, 2007)."

Jan 1, 2015

By C. Heath

US coal consumption reached new heights in 1985, but production was constrained by excess consumer inventories. Domestic consumption of coal reached a record 742 Mt (818 million st) during the year. This is a 3.4% gain over the previous consumption high 718 Mt (791 million st) in 1984. An additional 84 Mt (92.7 million st) of US coal were shipped abroad in 1985, up 13.7% from exports a year earlier. Coal production in 1985 totaled 804 Mt (886 million st), 1.1% below the record 813 Mt (896 million st) produced in 1984. The slight decline in coal output is attributed primarily to a 13% drawdown of large consumer stockpiles built up in 1984 in anticipation of a miners strike that never occurred. Coal demand, and hence production, were also restrained by slower economic growth in 1985 and additional gains in nuclear generation of electricity. Domestic market requirements for coal in 1985 were mixed. Electric utility consumption rose 4.4%; coke plants consumed 6.7% less coal; coal requirements in the other industrial sector expanded by 2.1% and consumption in the residential and commercial sector fell 14.8%. The 2.2% increase in electric power generation in 1985 resulted in a 4.4% rise in utility coal consumption, totaling 630 Mt (694 million st) for the year. Twenty-nine of 45 states where coal-fired electric power plants were operating shared in the 26.7 Mt (29.5 million st) increase in 1985. Coal receipts at utilities fell by 16 Mt (18 million st) as these facilities worked off 21 Mt (23.4 million st) from stockpiles during the year. Electricity generation at coal-fired power plants similarly climbed 4.4% to 1.4 trillion kWh in 1985. This gave coal a 56.8% share of electricity generated from all energy sources compared with 55.5% in 1984. The average price of coal delivered to these facilities remained essentially unchanged during the year. It declined on 1.5% from $38.26/t ($34.71 per st) during the fourth quarter of 1984 to $37.70/t ($34.20 per st) in the fourth quarter of 1985. Coal consumption at coke plants continue to reflect a depressed steel industry. After rebounding 18.9% in 1984 for the first time in five years, coal consumption at coke plants again declined 6.7% to 37 Mt (41.1 million st) in 1985. Coke consumption 26.5 Mt (29.3 million st) exceeded production, 26 Mt (28.7 million st), in 1985. This resulted in a 1-Mt (1.2-million st) decline in coke stocks at producer and distributor levels during the year. The average price of coal delivered to coke plants decreased 7.6% from $64.30/t ($58.34 per st) during the final quarter of 1984 to $59.42/t (53.91 per st) in the last quarter of 1985. Coal consumption in other industries, including all manufacturing and industrial consumers except coke plants, totaled 68.3 Mt (75.3 million st) in 1985. This was the highest level attained in more than a decade. But the lower percentage rise last year (2.1% compared to 11.8% in 1984) reflected slower growth in the nation's economy in 1985. The average price of coal delivered to industrial firms declined 4.5% from $42.32/t ($38.39 per st) in the fourth quarter of 1984 to $40.39/t ($36.65 per st) in the last quarter of 1985. Coal-producing states in Appalachia mined 9.8 Mt (10.8 million st) tons less in 1985 than in 1984 for a 2.4% loss. The largest contributors to the region's production decrease to 393 Mt (433 million st) were Pennsylvania, down 14.7% to 60 Mt (66 million st); Ohio, down 8.3% to 32.6 Mt (36 million st); and West Virginia, down 2.9% to 115 Mt (127 million st). Conversely, eastern Kentucky production was up 4.8% to 111 Mt (122.8 million st) in 1985, while production in Tennessee climbed 9.7% to 40 Mt (44 million st). No coal was mined in Georgia last year. Coal production in the interior region in 1985 declined 3.9% to 173 Mt (190.4 million st). Substantial production losses occurred in Indiana, down 8% to 31 Mt (34.5 million st); and in western Kentucky, down 7.9% to 36 Mt (40 million st). Coal production in Texas rose 5.7% to 39 Mt (43.5 million st) in 1985. Louisiana began mining lignite 140 kt (151,000 st) during the year. Production in the western region increased 3.4% to 238 Mt (262.5 million st) in 1985. Wyoming, up 5.3% to 125 Mt (140 million st); and North Dakota, up 16.5% to 23.5 Mt (26 million st) contributing the largest amounts. Production gains were also shown in Washington, Utah and, notably, in Alaska where coal output climbed 72.9% to 1.3 Mt (1.5 million st) in 1985. Most of the additional coal produced in Alaska last year was shipped abroad. Coal stocks held by consumers totaled 154 Mt (170 million st) at the end of the year. This was 27 Mt (30 million st), or 13.7% below the inventory level at the end of 1984. Stocks held by producers and distributors declined by 868 kt (957,000 st), or 2.8% in 1985 to 30 Mt (33 million st). A drawdown in stockpiles occurred in each consumer sector during 1985. Stocks held by electric utilities totaled 142 Mt (156 million st) at the year's end, 13% lower than stock levels at the end of 1984.

Jan 5, 1986

By M. H. Thomas

El presente trabajo describe tres ejemplos de empresas en Australia que utilizaron carbones provenientes de fuentes locales para el encendido de sus hornos. Así también se muestra los principios generales de la operación de los hornos rotatorios, la quema de combustible pulverizado, el encendido directo e indirecto, la contaminación de cenizas y los problemas derivados de la eliminación de azufre.

Nov 1, 1984

By Bao K. Le, Khang T. Truong, Masaki Kitazume, Toru Kobayshi, Long P. Le, Tanaka Hitoshi, Makoto Kamimura, Hoang-Hung Tran-Nguyen

"Earth levees constructed using dredged materials taken from a river along an earth levee have annually damaged in the Mekong Delta due to high void spacing in earth levees and floodwater. Sliding and internal erosion due to floodwater or piping are two key factors causing earth levees’ failures. This study proposed to apply Deep Mixing Method (DMM) to reinforce earth levees in the Mekong Delta, Vietnam. The DMM creates a soil cement wall or soilcrete wall having better engineering properties such as higher strength and low hydraulic conductivity than those of the in-situ soils. The DMM can be applied to reinforce earth levees with limit additional materials that provinces in the Mekong Delta are difficult to supply. The study investigates capacity of the DMM to reinforce earth levees in the Mekong Delta, Vietnam against annual floods. Seepage and slope stability analyses under various conditions were performed with various scenarios of earth levee’s body. The analysis results indicate that the DMM can create a wall that cuts off piping across earth levee significantly and can improve stability against deep sliding due to rapid drawdown of the floodwater.INTRODUCTIONThe Mekong Delta produces agriculture products of 50% of the whole country even though the Mekong Delta has an agriculture area of 30% of the country (Wikipedia 2014). Rice is the main product for the domestic demand and export. This is the main reason why the local people want to cultivate rice 3 times per year to increase the total rice product for export. To do that, the local provinces have constructed earth levees surrounding each area of 100-200-hectare against annual floods to protect rice fields, and farmers can grow rice in the whole year. There are thousands of kilometers long earth levees in the Mekong Delta, and the local governments have spent millions of US dollars to repair and to maintain their earth levees yearly (reports of Dong Thap province 2012; 2014).Earth levees in the Mekong Delta have often failed in flood seasons (e.g., from August to December), especially in Dong Thap and An Giang provinces – the two provinces confronting directly the annual floods from the Mekong River when the floods reach the Vietnam land. The main failure of earth levees is piping, and then causing collapse of some section of an earth levee. An earth levee was usually constructed by piling up dredged materials along a river with minimum compaction. Subsequently, floodwater flows through connected void spacing and washes out soil particles in the body of an earth levee slowly to create piping. Annual wet-dry cycles make the top clay layer swelling and shrinking to form cracks that can store rainwater to trigger sliding (whitlow 2001; Ton That Vinh 2003)."

Jan 1, 2015

By D. W. Dareing

Multiple branch wellbores and horizontal holes, when applied to deep lying ore bodies, have the potential of significantly reducing well costs by reducing total footage drilled per acre of well pattern. In addition, horizontal holes may increase sweep efficiency. Well completion is a major problem. They must be cased to contain leaching solutions within the underground portion of the production loop. Several drilling and completion concepts are given and evaluated in the report. Our evaluation shows that there is economic incentive to further develop these concepts for field application to ore bodies 1,500 feet. Multiple branch concepts are the most attractive. They can reduce well costs by as much as 30° when applied to 2,000 feet ore body depths (44%, at 5,000 feet) and can accommodate a lamer pump than conventional vertical wells. We recommend this concept be developed further to accommodate either dual or triple branches.

Jan 1, 1980

By T. Vovan, A. Galibois, M. Fiset

"In order to establish some links between the 22 specimens found on the site of Les Forges du St. Maurice, their slag inclusions have been analyzed by electron microprobe. Comparison between their contents of various specific oxides allowed us to segregate them into two major groups and even to isolate two sub-groups possibly characterized by some equilibrium between their oxides and/or the type of ores used.In all probability, limes/one coupled systematically with a soil rich in hydrated aluminum silicates was used as a flux.Based upon the existence of a pseudo equilibrium between the slag and the metal, the elaboration of the bulk of the specimens can be ascribed to the indirect rather than the direct method whereas the process temperature can be estimated at at least /400°C.RESUMEDans le but d'etablir des liens entre les 22 objects provenant des Forges du St-Maurice, leurs inclusions de scories ont été analysées par microsonde. La comparison des teneurs en divers oxydes a permis de les séparer en deux groupes majeurs et même d'y distinguer deux sous-groupes pouvant être reliés à la forme d'équilibre entre certains oxydes et/ou au type de minerai utilisé. Selon toute vraisemblance, le fondant utilisé était de la pierre à chaux à laquelle on ajoutait systématiquement une terre riche en silicates hydratés d 'aluminium.Des considérations sur l'existence d'un certain équilibre entre les scories ei le métallaisset croire que la plupart des objets ont été élaborés plutôt par la méthode indirecte que directe et que la température d'élaboration se situait à au maint 1400°C."

Jan 1, 1984