Search Documents

By S. A. Sadough vanini

In this paper the influence of temperature on the flow behavior and rheological characteristics of an A356 alloy in the semi-solid state using backward extrusion process are studied experimentally and numerically. Simulation process is done by dynamic explicit in ABAQUS software for each forming condition. A cooling slope treatment was employed in order to obtain a non-dendritic microstructure. Experiments were performed in 5 temperatures and 4 different wall thicknesses. In the low forming speeds, liquid fraction had time to escape from solid phase forward the samples? wall. This condition was the main reason for the segregation phenomenon seen in the base and walls. Viscosities were determined using the force-displacement graphs obtained form back-extrusion tests. As observed experimentally, in a constant temperature, increase of shear rate resulted in decrease of alloy viscosity exponentially. Raising the temperature increases the liquid fraction hence reduces the semi-solid alloy viscosity. The results of experimental and simulation are compared and there is a good adaptation.

Oct 1, 2011

By M. Mohammadi Zahrani

The morphological modification of primary and eutectic Mg2Si phases by bismuth (Bi) addition in Mg-5wt.% Si in-situ composite was investigated. It was found that with addition of 0.5wt.% Bi, the morphology of primary Mg2Si precipitates was altered from coarse dendritic to polygonal shape, and their mean size was significantly decreased from more than 20 µm to about 8 µm. Moreover, the rod-like eutectic Mg2Si in Bi modified Mg-Si alloy solidified much finer than that of the base alloy. Such improved microstructure of the modified alloy resulted in 10% tensile strength and 20% elongation improvement. The isotropic growth manner of primary Mg2Si particles in modified alloy was attributed to the poisoning of growth in preferred directions by dissolving Bi atoms in Mg2Si lattice. The reduction in size of eutectic Mg2Si was found to be the result of Mg3Bi2 compound formation around eutectic Mg2Si rods.

Oct 1, 2011

By S. Rash Ahmadi

Welding is highly reliable and efficient metal joining process. In welding the metal adjacent to the weld joint is subjected to severe thermal conditions. As a result, complex changes in metallurgical structure occur in this region. These changes in structure depend on the material and the temperature history experienced. Friction stir welding (FSW) is relatively a new welding process in which, heat is generated by friction between the tool and the workpiece. The amount of heat conducted into the workpiece determines the quality of weld, residual stress and distortion of the workpiece. The objective of the current work is to study the transient temperature in a friction stir welding. So, a three dimensional transient analytical model is used to study the thermal distribution during the welding. Heat input from the tool shoulder alone is considered in the model. The process parameters like axial load, welding speed and tool rotational speed, used in actual FSW process are taken to build the model. This analytical model is very useful for select the optimized affected parameters in friction stir welding. The model illustrates the comprehensive equation including actual affected parameters in FSW and it can be used for different materials. In addition to the above the thermal history finds application in design of welding tools.

Oct 1, 2011

By S. A. Sadough vanini

In this paper, Stress-Strain-Temperature relations for Shape Memory Alloys are studied. Temperature effects on Shape Memory Alloys are different from those related to ordinary materials. In ordinary materials, elastic characteristics can be assumed to be constant in low temperature ranges, and only the deflection arising from temperature changes could be added to the elastic defection. As long as two phases of austenite and martensite could be present in Shape Memory Alloys simultaneously, elastic modulus follows temperature and temperature gradient. In continue a smart actuator is investigated considering a homogeneous cantilever beam. Beam bending is established by using shape memory wires. An initial strain is imposed to shape memory wires in a low temperature, and then, they are installed in the outer surface of the beam. Therefore, since the temperature is imposed in these wires and they cannot have free recovery strain, the compressive recovery stress will be produced in the outer surface. This will result in a deflection in axial direction of the beam. At first, beam deflection is calculated on the basis of theoretical relations and solving the relevant differential equations. Afterwards, experimental tests are performed on an elastomeric beam equipped with shape memory wires. When a voltage is applied, a temperature rise will occur in the wires; then, this temperature rise causes a deflection in the beam. Finally, the theoretical and experimental results? comparison indicates a good conformity. One capability of this actuator is its high flexibility, and by controlling the inlet current, the end-beam deflection can be controlled.

Oct 1, 2011

By B. Farabi Khoshmehr

In the present study the effect of Silicate Sodium oxidation agent concentration and Plasma Electrolytic Oxidation (PEO) treatment time were investigated on properties of oxide layer on Aluminum alloy. The phase composition and surface morphology of PEO films were evaluated through x-ray diffraction (XRD) and scanning electron microscopy (SEM). Pin on Plate abrasive machine were used to investigate of were resistance of coating. The results showed that oxide layer which formed on Aluminum surface consist of high temperature a- Al?O? and ?- Al?O? phases. The diffraction peak intensity and percentage of these phases were increased by increasing silicate sodium concentration. Microscopic studies revealed a porous surface for PEO coating. This was affected by silicate sodium concentration and oxidation time. The wear test results showed that the weight loss of PEO coating was reduced due to improvement of their wear resistance.

Oct 1, 2011

By S. Rash Ahmadi

Thin brittle coatings are deposited or developed on component surfaces for different reasons. In many practical applications the coatings are stressed by externally applied loads. Under such conditions, coating failure can occur. In this paper the probability of the extension of surface crack in coated materials due to cylindrical sliding indentation is analyzed. Contact loading problems typically result in multi-axle and strongly inhomogeneous stress fields near the contact surface. This property which strongly affects the stress intensity factors is taken into account in the failure analysis. Edge cracks were selected to model the actually accruing surface flaws. A suitable method is described for calculating the contact stress fields in coating and substrate. The coating is idealized as a brittle-elastic layer of uniform thickness, which is bonded to the surface of a half space. Method of linear elastic fracture mechanics are then used to calculate the load required to cause fracture in the coating.

Oct 1, 2011

By Sadough vanini Ali

Hot deformation behavior of functionally graded steel (FGS) was investigated via conducting hot compression tests at different temperatures and strain rates. Functionally graded steels consist of ferrite, austenite, bainite and martensite layers that are made by diffusion of alloy elements during the melting process. The zenerhollomon parameter has been used to describe the flow stress variations as a function of temperatures and strain rates. The parameter values for all the layers via using the boundary conditions was determined based on composite graded behaviors. Furthermore by applying the rule of phase mixtures, the whole strain rate applied on composite would be the sum of layers strain rates considering the layers volume fraction, while the layers have the same stress. Consequently the composite flow stress for each strain rate and temperature was determined.

Oct 1, 2011

By Saeid Akhavan

Accumulative roll bonding (ARB) is a severe plastic deformation process for achieving ultrafine grains in metallic sheets without changing the sample dimensions. In this study, ARB process was carried out on 5083 aluminum alloy sheets up to 6 cycles. In this process, the surfaces of the strips to be joined are roughened and cleaned and then stacked. After stacking, the specimen is roll-bonded by rolling using a 50% reduction. The rolled specimen is cut into two halves, and the above-mentioned procedure is repeated for several times. Microstructural characterizations were analyzed by transmition electron microscopy (TEM). Tension and Vickers hardness tests were performed on produced sheets for evaluating their mechanical properties. In order to clarify the failure mode, fracture surfaces after tensile tests were observed by scanning electron microscopy (SEM). The results indicated that at the early stages of ARB process, grains were subdivided by deformation induced boundaries. After several ARB cycles, lamellar structure elongated in the rolling direction contains lamellar boundaries was formed. With increasing the strain, mean spacing of lamellar boundaries decreased. Finally, continuous recrystallization resulted in a microstructure covered with small recrystallized grains with an average diameter below 100 nm at the end of four cycle. The tensile strength and hardness of the 6 cycle ARB processed 5083 aluminum alloy sheet increased about two and three times of the initial values, respectively. Results indicated conformity between mechanical evolutions and microstructural changes during ARB process. Fracture surfaces observations showed that failure mode in ARB processed aluminum is shear ductile rupture with elongated small dimples.

Oct 1, 2011

By S. Rash Ahmadi

One of the most important elements in power plants is rotors and repairing the damaged rotors is very important in view point of economics. One of the most complicated problems in power plants is increasing of stiffness of the turbine rotors. This problem which occurs mainly due to thermal shock or rubbing makes to exit damaged rotor from service. These elements can be repaired effectively by heat treatment methods. Tempering heat treatment is the most common solution for straightening of damaged rotors but it requires having good knowledge about heat treatment parameters (temperature and time) and their affects on fundamental properties of rotors. In this article, a suitable method is introduced in order to modify the increased stiffness in journal part of rotors due to martensite transformation, using heat treatment tempering process.

Oct 1, 2011

By Sadough vanini Ali

Charpy impact energy of functionally graded steels produced by electroslag remelting in crack divider configuration has been modeled in various strain rates. It has been well known that majority of materials indicate different behaviors under different strain rates and temperatures. Therefore, modifying the elastic-plastic model considering the effects of strain rates and temperature gives us an acceptable prediction of these composites behaviors in impact test. In this investigation, graded steel was divided in to several layers in which the layers have the same strains under the impact. Constitutive equation describing the flow stress variations as a function of strain rates and temperatures, have been used to express the stressstrain behavior of layers. The parameter values of constitutive equation determined for all the layers via using the boundary conditions based on composite graded behaviors which were the characterized ferrite, austenite, bainite and martensitte phases. Consequently by applying the rule of phase mixtures and ascribing the impact energy of each layer to the area of stress-strain curve of the same layer, the whole impact energy of composite is the sum of layers impact energy with considering the layers volume fraction.

Oct 1, 2011

By F. Hosseini

Shaping of metals by thixoforming relies on the unusual flow behavior of semisolid slurries containing nondendritic solid phase. The Flow behavior of metallic alloys containing both solid and liquid phases is investigated in the low solid fraction range (, 55%). This behavior depends on both the solid fraction and the shear rate. Four different shear rates is applied using back extrusion technique and flow stress versus true strain in different solid fraction is compared. It is well accepted that the flow stress s of alloys in their semi-solid state obeys to a thixotropic behavior, due to agglomeration and dissagglomeration phenomena during forming. The load-displacement curves produced from the tests may show an initial peak, believed to originate from a skeletal structure which rapidly breaks down under shear. Apparent viscosity obtained from this method is compared with other works and the proper power law of pseudo plastic state is introduced.

Oct 1, 2011

By A. Sadough vanini A. Kami

In this paper, effects of different ageing treatments on the mechanical properties, microstructure and formability of 7075 aluminum alloy have been studied. Forming limit diagrams of the alloy have been obtained for four ageing conditions including T6, OA1, OA2 and O. For this purpose, combination of uniaxial tensile tests and the Erichsen cupping tests with different sizes and shapes of sheet specimens have been performed after each ageing treatment. The highest formability and the lowest formability have been observed at samples with O and T6 ageing treatments, respectively. Also, investigation of precipitated microstructures showed that the size of precipitation particles has a significant effect on the formability of the alloy. Formability improves with coarsening of precipitation particles.

Oct 1, 2011

By A. A. Nourbakhsha

During the last few years, low cement castable refractories found more application in industry, because of good low and high temperature mechanical properties.In the case of alumina based castables ,usually fume silica or reactive alumina are used as superfines in the matrix to form mullite at high temperature which depends to source of alumina . Mullite network formation improves the hot mechanical properties and thermal shock resistance of bodies. The mullitisation of andalusite (so called primary mullite) also produces a certain amount of rich silica glass, part of it being expelled out of the grain. This phenomenon restrict the application of andalusite low cement castable in pig iron ladle. In this research, firstly 8 pig iron ladles from ESC(esfahan Steel company) with different conditions selected and monitored during usage to determine of main factors affecting on corrosion of refractories. Results showed that tap to tap time and undischarged pig iron are the main ones.Therefore monolithic refractories such as castables which increase thermal shock resistance could be substituted. Regarding to ternary phase diagram of Al2O3-SiO2-CaO ,fumed silica was selected as fine particle.After optimization of particle size distribution by using of modified andreasen equation and rehological properties ,different mixture were composed with andalusite ,fume silica, reactive alumina,secar 71 ,SiC and kyanite.All aggregates system components were mixed dry for 1 min in hobart mixer .After water addition wet mixing was continued until getting flowing about 4 min.The ready mixes were poured in the moulds of of 25mm X 25mm X 140mm with vibrations .After demoulding the samples were cured for 24 hrs and dried at 110OC/18hrsand then fired at 1100-1500OC. Physical ,mechanical ,phase analysis(XRD) and microstructure studies (SEM)were carried out according to ASTM standards. Results showed that by addition of kyanite ,more mullite phase formed through the matrix but,because of expansion occured during this phase transformoration, some cracks formed and mechanical properties decreased.By SiC addition the silica film on the surface of SiC lead to improvement of mechanical properties at high temperature

Oct 1, 2011

By Saeid Akhavan

Accumulative roll bonding (ARB) is a severe plastic deformation process for achieving ultrafine grains in metallic sheets without changing the sample dimensions. In this study, ARB process was carried out on 5083 aluminum alloy sheets up to 6 cycles. In this process, the surfaces of the strips to be joined are roughened and cleaned and then stacked. After stacking, the specimen is roll-bonded by rolling using a 50% reduction. The rolled specimen is cut into two halves, and the above-mentioned procedure is repeated for several times. Microstructural characterizations were analyzed by transmition electron microscopy (TEM). Tension and Vickers hardness tests were performed on produced sheets for evaluating their mechanical properties. Moreover the texture parameter of the ARB-ed samples was calculated using their XRD patterns and the related equation. Additionally, the texture evolution during the ARB process was demonstrate by analyzing the measured pole figures and orientation distribution functions (ODF) and skeleton lines. The results indicated that at the early stages of ARB process, grains were subdivided by deformation induced boundaries. After several ARB cycles continuous recrystallization resulted in a microstructure covered with small recrystallized grains with an average diameter below 100 nm at the end of four cycle. Texture analysis revealed fiber textures have been discovered with continiuose of the ARB process cupper. Brass, S and dillamor textures identify which their differences are in intensity of ARB process. Results indicated conformity between mechanical evolutions and texture evolutions during ARB process.

Oct 1, 2011

By Mahmoud Shakeri1

Various types of thin-walled structures have been frequently used as energy absorbers to mitigate the adverse effects of impact and hence protect the vehicle structure under consideration when subjected to different loading conditions. Compression tubular structures that buckle in a progressive manner, can be used to advantage, providing inexpensive and versatile, but nevertheless weight and stroke efficient energy absorbers. In this paper quasi-static nonlinear finite element simulations are performed to study the effects of number of corners of the cross-section, wall thickness, plastic hardening rate of material, foam-filler and load angle on deformation mode and mean crushing force of tube. Crush strength increases as the number of corners of the cross-section increases, though it almost saturates for the number of corners beyond 11. Higher plastic hardening rate stabilizes the collapse pattern. Foam-filled tubes seem to have higher critical load angles in oblique loading and display a more stable and gradual decrease in mean load over the transition region. Substantial decrease in the initial peak load and dynamic load at any a given deflection was observed as the load angle increases. The investigation of bitubal arrangements and Multi-cell tubes reveals that these may be preferable to monotubal specimens due to the presence of the inner profiles. In addition, a comparison is conducted between the numerical and experimental results of the mean forces of some special angle elements. Good agreement is obtained.

Oct 1, 2011

The adoption of new technologies is accompanied by risks that the stakeholders will wish to understand and minimise. The process of developing a dynamic simulation and the plant it will be used in provides a discipline and attention to detail that highlights and provides an opportunity to mitigate risks that will exist in a production environment. The simulations will enable investigation of what the outcome of process failures will be and the impact maintenance. Enumerating this information will enable designs to be optimised and operating and control strategies to be tested.The success of new technology is dependent on the operators and their understanding of it and the machines that use it. In this context dynamic simulations can provide training and experience without risk to personnel, equipment or production. This experience will include situations that would not be induced in a production plant for training purposes. This paper outlines a generic template for a dynamic simulation that can be used to evaluate the introduction of an emerging technology into an operating environment. It includes process flows and surge capacity, breakdown and maintenance, operator interactions and availability, push and pull production scheduling and system control.

Sep 26, 2011

By J Ortiz

In almost all copper mining companies, mine planning is done considering different time frames, leading to long-term (life-of-mine) (LOM), medium-term (first three years) and short-term (first year, monthly, weekly, and up to daily plans). Shorter term plans are usually associated with more abundant information, hence models with lower uncertainty. However, they capture more of the variability found on the geological attributes. In long-term models, usually estimation methods tend to hide this variability, providing smoothed interpretations.Medium and long-term plans consider average values for the parameters and optimisation techniques are applied aimed at maximising the economic profit. Short-term plans, on the other hand, are made to comply with the medium-term promises, maximising the use of the available resources (equipment and processing capacities) and dealing with the variability not characterised in the previous planning stages. This generates an important gap between the short-term and the medium and long-term plans. A case study was made using an important oxide copper mine, where the variability found in the short-term plan has a large impact in the productive process, thus reducing the daily ore grade variability is an important goal. In this paper, this planning issue is addressed by creating medium-term mine plans using mixed integer programming which are compared using the output of a simulation of the daily extraction that is aimed at satisfying the daily constraints of the processing plant, the availability of mining equipment and the variability of ore grade. The result shows the expected gap between these mine planning processes, which suggests correcting some of the parameters used in future medium and long-term plans.

Sep 26, 2011

By D T. Ribeiro, J F. C L Costa, J C. Koppe

Drilling and sampling are responsible for most of the costs during mineral exploration, especially in multi-elements and polymetallic deposits, such as iron, manganese and bauxite deposits. On these deposits, often it is necessary to estimate multiple attributes at several granulometric fractions, ie distinct particle sizes. This paper investigates the effect of sampling at a close spacing grid only the head grades for the multiple chemical species in iron ore deposits. The remaining required data at the various grain sizes are sampled at a sparse grid. The derived geological model is checked for precision and accuracy comparing the output obtained against a model obtained using a complete isotopic data set including head grades and chemical analysis at each granulometric fraction analysed at all sampled positions. Among the several tested alternatives, the best procedure for dealing with the posed problem involved utilising the correlation coefficients between the grades at distinct fractions to obtain an isotopic database prior to interpolation. Cokriging was the method used, based on the intrinsic coregionalisation model. Estimates were obtained with the quality needed for the proposal of the study. Results showed that at least 50 per cent of the blocks were estimated with errors less than ten per cent relative to the grades obtained at the reference model, using only 15 per cent of the granulochemical data employed to obtain the reference model. The methodology also preserved the correlations between the attributes in their several granulometric fractions on the estimated model.

Sep 26, 2011

By L van Latum, A Koh, I Thomas

Haul truck drivers are at a high risk of developing fatigue due to the monotonous nature of the work and demanding shift rosters. In the mining industry, fatigue is identified as a major contributing factor in several fatal accidents a year. A number of fatigue detection devices are now available, that can contribute to improved fatigue risk management in the mining industry. This paper describes the technology and algorithms behind one particular product which is both predictive and un-obtrusive to the operator. The Advisory System for Tired Drivers (ASTiD), was developed by Fatigue Management International (FMI) in collaboration with the Loughborough Sleep Research Centre (LSRC), both in the United Kingdom. While this system includes a model of the human circadian rhythm as a bias for predicting expected fatigue risk by time of day, it also uses yaw data generated by a solid-state gyroscope in the horizontal plane. Algorithms analyse this data to determine the level of monotony of actual driving conditions and to detect changes in steering control caused by driver fatigue. During normal levels of attention, a haul truck driver applies continuous, small adjustments to the steering wheel. As the level of fatigue increases, steering adjustments become less frequent and more erratic. Differentiating between these modes of control in the highly variable mining environment is accomplished by chromatic processing of the gyroscope data. This paper will go into some detail explaining the principles behind chromatic processing and the specific application of these in detecting fatigue in haul truck operators.Technology in itself is not the solution to addressing operator fatigue, but it plays an important role in ongoing monitoring and maintaining awareness with mining personnel. Furthermore, the specific principles behind ASTiD technology support a risk-based approach to fatigue management, allowing optimisation of the mining operation for productivity as well as safety.

Sep 26, 2011

By E Ben-Awuah

Mine planning is the backbone of all mining enterprises and determines the profitability or otherwise of any mining investment. Providing high quality ore and tailings containment at the right time are the main drivers in oil sands mining. Recent environmental and regulatory requirements also makes waste management an integral part of mine planning in the oil sands industry (Directive 074). Due to the limitation of lease area, the pit phase advancement in oil sands mining is carried out simultaneously with the construction of tailings dykes in the mined out areas of the pit. These in-pit dykes are constructed to hold tailings that are produced during the processing of the oil sands ore after an initial external tailings facility. Most of the materials used in constructing these in-pit and ex-pit dykes come from the oil sands mining operation, making it necessary to have a plan for supplying the dyke material. The research problem here is categorised as: determining the order of extraction of ore, dyke material and waste to be removed from a predefined ultimate pit limit over the mine life that maximises the net present value of the operation û a strategic schedule; anddetermining the destination of dyke material that minimises construction cost depending on the construction requirements of the various dykes as per their designs û an operational schedule. There has been developed, implemented and verified a theoretical optimisation framework based on mixed integer goal programming (MIGP) to address the oil sands long-term production scheduling and waste management problem. The research introduced the development of multiple material types and multiple destination optimisation techniques using MIGP in the context of mine planning. This study presents an integration of mixed integer programming and goal programming in solving large-scale mine planning optimisation problems using clustering and pushback techniques.

Sep 26, 2011