Search Documents

A laboratory size solvent extraction apparatus has been constructed, which incorp- orates three stages of countercurrent extraction, followed by two stages of counter- current stripping. The model uses a gravity flow system from one stage to another and air lift pumps to recirculate organic and aqueous phases. A novel pump/mixer system is used to transfer solutions from the mixer compartments to the settler compartments. The model has proven valuable in the teaching of solvent extraction principles.

Jan 1, 1999

By M. Barati

A collaborative research between University of Toronto and Hatch was conducted to understand and optimize the process conditions pertaining to a novel steelmaking technology. In this technology, known as CRISP, direct reduced iron is continuously melted and refined in a stationary electric arc furnace. The major challenge against continuous operation of the electric furnace was identified to be minimizing the corrosion of the refractory in order to achieve uninterrupted operation for a minimum of one year. Theoretical analysis and bench scale experiments together with two pilot runs resulted in defining an operating window for slag chemistry that would minimize chemical attack to the refractory while satisfying the oxidizing conditions required for sufficient decarburization. An analysis of the process in terms of energy consumption and emission of greenhouse gases revealed that it is superior to the current batch DRI-based steelmaking technologies.

Jan 1, 2011

By M English, M Yumlu

At times of high metal prices, mining projects that have previously been put into the ætoo hard basketÆ are now being more closely examined. Typically these projects include the potential recovery of small mineable tonnes with high contained metal values and often with poor ground conditions. For many underground mining projects, the drift and fill method is viewed as a high-cost method and a æmethod of last resortÆ. As a result the method is not well known in Australia and it is the authorsÆ view that the method is under utilised. The drift and fill method can be applied to a variety of underground mining situations and is a preferred method for some orebody geometries and where ore recovery is viewed as a key to project success. This paper examines some of the critical mine planning and backfill issues involved with the drift and fill mining method.

Jan 1, 2008

By John V. Beall

WHEN the atomic age broke suddenly upon the world in 1945 with all its terrible implications, predictions concerning the future of atomic energy were as numerous as columnists and often inflated. Today, some seven years since the explosion and probably ten since the Government took over development of nuclear energy, the impact on our way of living has been largely political (except of course for the thousands of people who have become employed in the AEC). Considering the world situation, weapons have come first naturally. But credible progress in the plow-share uses of nuclear energy-medicine, agriculture, power-can also be noted.

Jan 3, 1953

By Charles M. Cooley

A NOTED Prospector Passes-Stories of the grizzled old prospector that discovered what turned out to be a famous and highly profitable mine, only to die in poverty through the shenanigans of "the Interests," are legion. It is pleasant, therefore, to be able to report that the discoverer of one of Canada's most famous mines was more fortunate.

Jan 7, 1953

By E. H., Edwerd H. Robie

WILLIAM CHURCH was one of the founders and the first president of the Detroit Copper Mining Co. and was the first man to interest the Phelps Dodge company in the possibilities of the Morenci district, in the '70's. One rather interesting story concerning him is told by James Colquhoun, at one time president of the Arizona Copper Co., in his "History of the Clifton-Morenci Mining District." It seems that a geologist visited the Detroit company's mines and gave Alec McLean, then mine superintendent, quite a lesson on the proper mineralogical terms for what he saw in passing. Later, McLean handed out a few of them to Mr. Church as they walked through the mine on a tour of inspection. The latter had even less regard for a geologist than he did for sulphide ore, which meant little indeed, for in those days the rich ore was all oxidized, and there was no money in the sulphides. So Church was completely unimpressed by the geological and mineralogical terms that McLean had acquired from the visiting geologist. Church turned on him and warned him that so long as he was a member of his staff he was to understand that there were only two kinds of rock in his mines-the one was smelting ore and the other was waste rock, and he was not to forget it.

Jan 1, 1942

By Charles M. Cooley

DURING the last week in April, cards were sent out from New York to Institute members affiliated with the Mining, Geology, and Geophysics Div. The cards requested recipients to indicate their main technical interest, within the division, i.e., mining, or geology, or geophysics. The reason for the cards is simple. Within the Institute more than 8000 have expressed either primary or secondary interest in this division. However, there is no way to determine the technical association stimulating this interest.

Jan 6, 1953

By S. Averill, B. Schreiner, V. Sopuck

The La Ronge. Kisseynew, Glennie Lake and Flin Flon domains. the main focu for gold exploration in the southeast part of the Saskatchewan Shield, were subject to continental glacial ice advances from the northeast during the Quaternary. Based on forty-four auger hole along with surficial mapping, the general Quaternary stratigraphy in this area is observed to be composed of a lower till unit , an overlying stratified unit of glaciofluvial sand and gravel and/or a glaciolacustrine silt-clay unit. an upper till. and an upper tratified unit. The lower till is commonly found throughout the geological domains except where it has been eroded in glaciofluvial or fluvial channels. Glacial Lake Agassiz fo rmerly covered most of these prospective domains. The lacustrine deposits associated with the lake impede surficial geochemical surveys including soil. lake sediment. and biogeochemical surveys. The approximate extent of clay cover can be predicted from beach elevations. For instance. in the Waddy Lake area. clay i not known to occur above about 1,400 feet (425 m) elevation. Exploration techniques are hampered by clay in at least one third of the volcanic belt. Thi s influence is indicated by the fact that nearly all gold prospect found to date are located above 1,400 feet (425 m) while the area of clay cover is vi rtually unexplored. The upper till i related to a minor ice readvance. This till is the medium often sampled during soil surveys in the area . lts value as a geochemical ampling medium is dependent on the extent of erosional contact with bedrock highs on the lower till. Those areas which are relatively free of lacustrine and fluvial deposits are those where surface geochemical methods work best. In the Waddy Lake volcanic belt approximately 25-50% of the area may be suitable for surficial surveys. The area of the Star Lake prospect occurs above the 1,500 foot (460 m) elevation and was not covered by Lake Agas iz. The effectivene of till sampling as a surface sampling medium was tested in those areas above the clay level. Till orientat ion surveys were carried out at the Star Lake property and the Tower Lake prospect (Waddy Lake area) within the La Ronge Domain . Gold grain counts and analy es of heavy mineral concent rate from 7 kg surface ti ll samples were used to delineate dispersion trains down-ice from mineralization. In addition, the clay fraction and a 30 g (-80 mesh) subsample from the same till sample, were analyzed for gold . In the Star Lake area, ice direction is subparallel to the strike of several narrow northeast trending auriferous structures. arrow dispersion trains down-ice from known

Jan 1, 1986

By J. P. Harrison, M. Grenon

"This paper summarizes the results of numerical studies on drift stability in moderately jointed rock masses. It investigates the relative pertinence of geomechanical factors such as joint orientation, spacing and stress regime. This is undertaken using a distinct element model and a series of parametric studies. IntroductionIn evaluating the stability of drifts in jointed rock, it is often necessary to compromise by employing models that capture the complexity of the rock mass, but which are still simple enough to allow for their routine implementation. The distinct element method can arguably provide an eloquent method to accomplish this. This paper explores the applicability of the method by means of a parametric study aiming to identify the dominant factors that influence the stability of drifts in moderately jointed rock. To this end a commercially available 2D distinct element numerical model was used. A series of techniques are presented in an effort to quantify the results of any instability predicted by the model.This paper also demonstrates a case study where a 3D joint network model was integrated into the distinct analysis software package. The advantages, as well as the current limitations of this approach, are discussed."

Jan 1, 2001

By Dougal R. McCreath, Dwayne D. Tannant, Peter K. Kaiser

The Geomechanics Research Centre at Laurentian University in Sudbury, Canada, has undertaken a five-year research program into the design of support appropriate for control-ling damage caused by rockbursts. Rockburst damage mechanisms in Canadian hardrock mines are reviewed and a support design approach is presented. Each element in a sup-port system performs a reinforcing, holding, or retaining function. The desirable load-displacement characteristics for elements in burst-resistant support systems are described, and recommended support systems are presented for a spectrum of rockburst conditions ranging from minor to severe. A support system can be designed to (a) prevent the triggering of aground fall or a rockburst; (b) deform to accommodate the large imposed deformations arising from a rockburst; or (c) absorb the kinetic energy contained in ejected blocks of rock.

Jan 1, 1996

By L. Gutierrez, S. Gering, C. Calderon-Arteaga

"Drill and blast represent the most important, and sometimes the costliest processes in the mine. The cost of drilling and blasting operations greatly contributes to the “high cost trends of the overall mining operations” (Afum and Temeng, 2015). The use of available information to improve the drill and blast processes can be the difference between a wasteful process and one that is optimized for costs, safety and desired fragmentation. Mining operations have access to several types of data sets that include a variety of different systems. This information can be used to improve, evaluate and apply processes for drilling and blasting. This may include different types of data from the different stages of the process (before, during and after the drilling and blasting operations), such as hole locations (planned and actual), penetration rates, drill operators, fragmentation (expected and resulting), explosive (design and usage), geology, vibration and others. This information can be used on its own or combined for further analysis to reduce costs, improve safety and evaluate results. Fortunately, due to advances in mining software, drill and blast engineers can exploit this data and create reports to evaluate results and improve the drill and blast process. However, as users start combining information from multiple datasets and establishing standard operating procedures for reporting across multiple sites, it becomes valuable to create auditable, automated and sustainable workflows for handling the information.In some cases, the task of aggregating and standardizing the data formats has already been completed and is available to consumers via the Enterprise Data Warehouse (EDW). A data warehouse team extracts data from the source systems and transforms it so that it is meaningful for decision support (Wixom, Watson, 2007). The author’s initial implementation plan for the drill and blast solution included using data stored at the sites on local servers. However, we learned early in the process that much of the work for aggregating and supplying the required data was already completed and was available in the EDW ready for use. This saved time, reduced risk and added value to the system.The goal for this case study is two-fold: to show how information can be used to make decisions and improve processes, especially highlighting the value of using an EDW for managing drill blast information; and to discuss how technical challenges encountered during the implementations were resolved. This article targets users that want to better manage their drill and blast data or try to set up standardized workflows for using this information.This case study will discuss the process of implementing a drill-and-blast workflow at multiple sites within Freeport-McMoRan (FMI) using both data at the sites and information available from the EDW."

Jan 5, 2017

By L. Gutierrez, S. Gering, C. Calderon-Arteaga

"INTRODUCTION Drill and blast (DnB) represents the most important, and sometimes the most costly processes in a mine.. The cost of drilling and blasting operations greatly contributes to the “high cost trends of the overall mining operations” (Afum B. O. and Temeng V. A. 2015). The use of available information to improve the DnB processes can be the difference between a highly expensive process and an optimized one. Mining operations have access to several types of data sets and key information from a wide variety of different systems. This information is normally used to improve, evaluate and apply processes for drilling and blasting. This may include different types of data from the different stages of the process (before, during, and after the drilling and blasting operations), such as hole locations (planned and actual), penetration rates, drill operators, fragmentation (expected and resulting), explosive (design and usage), geology, vibration, and others. This information can be used on its own or combined for further analysis to reduce costs, improve safety, and evaluate results. Fortunately, due to advances in mining software, drill and blast engineers can exploit this data and create reports to evaluate results and improve the DnB process. However, as users start combining information from multiple datasets and establishing standard operating procedures for reporting this data across multiple sites, it becomes valuable to create auditable, automated, and sustainable processes for handling the information. In many cases the task of aggregating and standardizing the data formats has already been completed and is available to consumers via the Enterprise Data Warehouse (EDW). A data warehouse team extracts data from the source systems and transforms it so that it is meaningful for decision support (Barbara H. Wixom, Hugh J. Watson, 2007). Our initial implementation plan for the DnB solution included using data stored at the sites; however we learned early on in the process that much of the work for aggregating and supplying the required data was already completed. The goal for this case study is two-fold: to show how information can be used to make decisions and improve processes, highlighting the value of using an EDW for managing Drill&Blast information; and to discuss how technical challenges encountered during the implementations were resolved. This paper is targeted at users that want to better manage their DnB data or try to set up standardized workflows for using this information. This case study will discuss the process of implementing a DnB workflow at multiple sites within Freeport McMoRan Inc (FMI) using both data at the sites and information available using the EDW. The paper will begin with an overview of the project. The discussion will then describe how DnB processes were used to set up daily workflows in order to provide information for evaluating process and making decisions. The final section will discuss some of the technical challenges and how they were solved, as well as possible next steps for further improving the workflow."

Jan 1, 2017

By C. Navalkar

Systematic drilling & blasting techniques are currently being viewed in the mining & construction industry as a correct 8z scientific approach for optimization process in rock excavation, as drill & blast costs usually represent major share in total cost of production and also the environmental impacts plays an important role in designing of the operations. Designing a blast is a complex planning task, which for optimization, includes deciding the bench geometry with respect to the rock properties & geology of the area, capacity of the excavators, choice of explosives & detonation method, tiring sequence, etc. Optimization of blast design needs a detailed comprehensive study of all the above intersecting elements. Preblast & Post blast surveys are required for further improvements in blast designs. However, the choice of blast design depends upon the the requisite blasting results opted for and the cost you are ready to pay for the same. The blasting operation, in general, also involves numerous side effects namely, ground vibrations, fly rocks, dust, noise & gas pollution, air blast effect etc. Again these effects can be made tolerable up to a certain extent depending upon the limitations of the environmental obligations as may be specified by the concerned authorities.

Jan 1, 2001

By Jerald E. Harris

"Often taken for granted, drill accuracy plays a major role in the relative success or failure of a blast.Expensive technological advances in equipment capabilities, drilling tools, communications, explosives, and timing can quickly be nullified by poor drilling."

Jan 1, 1999

It is well documented that drill and blast outcomes affect the downstream mining processes of loading, hauling, crushing and grinding but it can also significantly impact on mine profitability via dilution, recovery percentage, lump generation (iron ore), fines generation (coal, iron ore), coal loss and final wall stability. Drill and blast must therefore be optimised to improve the overall profitability via positively impacting on productivity and saleable product generation. It is however, difficult to achieve this because of the complexity of the number of parameters that must be integrated and managed across the entire mine value chain, ie the concept of æMine to MillÆ. This paper highlights, via a simple case study, the need to have a mineÆs drill and blast system both in control (so that it is predictable to a high degree) and with minimal variability (so the design actually makes it into the field). This type of management control is essential prior to optimisation work being undertaken. The æTeam ApproachÆ is discussed to illustrate the methodology of achieving drill and blast optimisation. A case study is presented to illustrate the potential benefits of this approach which in this mine represented a 27 per cent reduction in powder factor with the downstream functions achieving higher productivity with the same or reduced maintenance costs. It is essential for Australian mineÆs to implement the appropriate management strategies and experienced personnel placement to ensure that their mineÆs drill and blast system is correctly managed to facilitate the optimisation of profit. Without this, the Australian mining sector will become increasingly uncompetitive.

Jan 1, 1999

By Ricardo Dr. Chavez, Mathieu Lachamp, Rob Dr. Farnfield

Pueblo Viejo is an open pit gold mine in the Dominican Republic which is always looking forward to implement the newest technology in the industry to improve all processes. Focusing on one of the pillars of the department and our company, digitalization, we’ve been looking for the technologies that allow us the automation of data generation, supervision and process innovation. That’s where a new Drill and Blast software takes place, helping to integrate the process from the beginning to end, right after the pattern is designed until it’s blasted, allowing us to track results like vibration, fragmentation, performance, cost and inventory of each blast in a single platform. The software helps engineers to generate back analysis by blast, bench, pit, month and many other ways, in a timely friendly manner. Therefore, we can catch business opportunities and improvement for the drilling and blasting process.

Jan 1, 2019

By Tamara Wiseman, David Stewart

"A Quarry located in Georgia is a green-field site established in 2011. The quarry lies in the eastern part of the Georgia Piedmont area. It is within a distinctive, northeast-trending belt of relatively high-rank metamorphic rocks known as the Kiokee Belt, a poorly mapped sequence of units that largely consists ofamphibolite and various schists and gneiss that are host for relatively young granite bodies andassociated pegmatite and aplite dikes."

Jan 1, 2017

By Braden Lusk, Tristan Worsey, Nathan Rouse, Kyle Hall

Loading explosives up hole has challenges that are typically not seen in down hole explosive loading. Most explosives applications are not up hole. Lack of experience and technology can cause significant problems when loading explosives up hole. When results aren’t achieved, the blame is commonly put on the design when the true problems are unknown. Not knowing the cause of the problem causes drill and blast designs to be over engineered and very costly with little success. Being able to know and record key data is crucial to actually solving the problem. This paper goes over blast instrumentation that can be used to trouble shoot drill and blast problems in up hole explosives loading in underground mines. The tools and procedures used to trouble shoot include velocity of detonation recorder, borehole tracking, seismographs, and borehole camera. Each item will be discussed in detail with a case study to show the usefulness of the instrumentation. The operation discussed in the case study had issues pulling raises and had hang ups in the stope shots. These problems caused production slowdowns and costly remediation blasting that was not very successful. The case study is an underground gold mine that used modified sub-level caving with backfill as the mining method.

Jan 1, 2018

By Paul L. Matrin

This paper will discuss the recent and on-going drill and blast optimization measures at the Sparkhule Limestone Quarry, which have resulted in a 44% reduction of drill and blast unit costs per ton of broken limestone. This amounts to approximately $240,000 of drill and blast saving per year at current annual production rates of about 2.5 million tons (2.3 million tonnes) total material shot. The reduction of drill and blast costs were accomplished by a detailed and controlled in-the-mine drill/blast experimentation and cost evaluation using 8 different blast pattern designs and shots totaling approximately 267,000 tons (242,200 tonnes) of shot and mucked material. A careful review of the geology of the deposit was performed to determine the different rock classification/strengths/structural properties and to adjust blast designs to optimize fragmentation for the different rock types. Equipment loading productivity and crusher throughput performance were monitored as part of the evaluation process to assure that an optimal fragmentation of broken rock was achieved with the new blast designs. The study included the review of bulk explosive and accessory selection criteria (ammonia nitrate/fuel oil mix - ANFO, mini prills (high density ANFO), sensitized and un-sensitized emulsions at a 30% emulsion/70% ANFO blend), blast pattern design, charge diameter and the cost of drilling. Laser profiling technology was used to assure proper bench heights, stemming and sub-drill footage and front row burdens. High speed photography, video and still photos were taken of the different designed shots to assist in the evaluation of the performance of each blast. Powder density checks, size distribution, back break, detonation velocity and pressure measurements were taken. Different borehole diameters were used for the drill optimization study and drilling cost and productivities determined. A detailed cost comparison between in-house blasting and complete shot service was prepared to evaluate if shot service is a cost effective alternative to current in-house loading and blasting including a review of the new and pending United States Bureau of Alcohol, Tobacco and Fire Arms (ATF) regulations and associated owner costs/risks and potential benefit of shot service.

Jan 1, 2004

By Tristan Worsey, John Henchion, Nathan Rouse, Yannick Lauras

"This paper presents an approach used to plan and evaluate drill and blast trials for a mine that currently mechanically excavates in-situ rock. The document presents the approach used to plan the trials, the key performance indicators (KPIs) that were necessary to evaluate the mining methods, the test matrix used during the trials, and the results of the trials. The trials, which occurred as part of an overall drill to mill optimization project at this site, helped to evaluate various blast designs using fragmentation results,drilling and blasting costs, and downstream costs. This project was unique in that (1) drill and blast methods were trialed on multiple rock types and various bench heights using a range of blasthole diameters and powder factors and (2) the load and haul costs were evaluated using a range of loading equipment, from 66 tonne (73 ton) excavators up to 250 tonne (276 ton) excavators. A ten year net cost financial evaluation of the material extraction alternatives was also prepared for the site management. Ultimately, the process of evaluating the drill and blast trials helped the management decide whether to continue extracting using mechanical methods or to introduce drill and blast methods to extract the rock."

Jan 1, 2017