Search Documents

By Wenjun Duan, Zongliang Zuo, Qingbo Yu, Qin Qin, Junxiang Liu

Moving bed has been widely used in the field of heat and mass transfer and reaction between solid particles and gas. In order to enhance the heat exchange coefficient, there will be tube banks inserted in the moving bed. In the process of drying ammoniates particles or heat recovery from high-temperature particles with moving bed, the particles flow behavior around the tube banks is significant. In this paper, the particles flow behavior around the tube banks is investigated, and all the results can provide guidance for the design and operation of a moving bed.

Jan 1, 2016

By Takahiro Miki

In order to use metallurgical grade silicon (MG-Si) as a starting material for solar cell, phosphorus has to be removed from silicon because phosphorus is a n-type dopant. On the other hand, silicon, ferrosilicon, and silicomanganese are widely used as deoxidizers in steel refining processes. Since most of the phosphorus introduced during the deoxidation process is brought into final products, it is important -to lower the phosphorus content of these alloys. Hence, thermodynamics of phosphorus in such metals is important for the evaluation of dephosphorization processes. In the present study, thermodynamic properties of phosphorus in molten Si-P alloys at 1723- 1848K and those of Si-Fe-P and Si-Mn-P alloys at 1723K have been determined by equilibrating respective metals in a controlled phosphorus partial pressure. The results are expressed as follows.

Jan 1, 1998

By Hideyuki Takahashi, Taro Aichi, Kazuyuki Tohji, Makoto Muramatsu, Rie Sato

"There are several ways to condition lead-based alloy anodes for zinc electrowinning: electrochemical treatment, chemical treatment and physical treatment. Two advantages of physical treatments are their productivity and variety. In this report, physical treatments, including blasting with silica, alumina, steel grit and cut zinc wire, were tested. The laboratory tests confirmed there were differences in the formation of anode scales during electrowinning and in the suppression of lead dissolution from the anodes. With an increase in the surface roughness, the misfit between the PbC""2 and the MnC>2 was mitigated and the anchor effect was promoted; these effects resulted in dense Mn oxide scales on the anode.IntroductionZinc is widely used for hot-dip zinc plating and for die casting alloys. As a supplier of materials, we have endeavored to produce zinc that is economical and contains as little impurity as possible. As a result of our efforts, a technology for consistently providing special high-grade (SHG) zinc has been established. However, as seen in the issuance of the Restriction of Hazardous Substances (RoHS) Directive, public awareness of the industrial impact of heavy metals on the environment has been heightened. Increasing efforts to control environmentally sensitive substances will be necessary for our production processes.Electrolytic SHG zinc is produced by electrodeposition in an acidic solution with a Pb-Ag or Pb-Ag-Ca alloy for the anode and an Al alloy for the cathode. Pb alloy anodes are widely used because of their excellent durability; however, they are a source of Pb, which is the main impurity of the product."

Jan 1, 2012

By Young-Dae Kim, Dong-Sic Kim, Jong-Jin Pak, Kyung-Hyo Do

"Sulfur is one of the most harmful elements in stainless steel (SIS) products and the specification of sulfur content is getting more severe for high grade SIS. In order to accurately control the desulfurization reaction in high chromium containing SIS melts, it is important to know the thermodynamic interaction between chromium and sulfur in Fe-Cr melts over a wide range of chromium content. In this study, the equilibrium sulfur distribution, Ls, between a Ca0-Alz03 slag and Fe-Cr-C,.,-S melts were measured under CO atmosphere in the temperature range of 1823-1923 K. The specific effect of chromium on the activity coefficient of sulfur in the melts was determined with the consideration of carbon effect on sulfur. A separate experiment was carried to determine. Ls between a slag and FeCr- S melts (Cr: 0-30 mass%) at 1873K to check the validity of the thermodynamic parameter determined in the present study.IntroductionFerritic stainless steels containing chromium (Cr) up to 30 mass% have been developed for a good corrosion resistance and a high formability to replace austenitic SIS. Especially, Sulfur (S) causes a reduction of high-temperature strength and the hydrogen induced cracking (HlC) in stainless steel for line pipes. [l]Many studies on the desulfurization of hot metal and liquid steel have been carried out for several decades and they used HzS-H2 gas equilibrium technique for measuring the effects of many alloying elements on the activity coefficient of S in liquid iron. However, the study on desulfurization of Fe-Cr melts was very scarce.[2] In order to accurately control the desulfurization reaction of high Cr stainless steel, it is essential to know the thermodynamic relation between Cr and S in Fe-Cr melt over a wide range of Cr content and temperature.In the present study, the thermodynamic interaction between Cr and S in liquid iron was determined by measuring the equilibrium distribution ratios of S between Fe-Cr-C,.1-S melts containing a wide range of Cr up to 30 mass% and a 55 mass%Ca0-45 mass%Alz03 slag of which the sulfide capacity was pre-determined using Fe-C,a1-S melts in the temperature range of 1823-1923 K. The validity of thermodynamic parameter determined in the present study was checked by measuring the S distribution between a Ca0-Alz03-Mg0 slag of known sulfide capacity and liquid Fe-Cr-S alloy at 1873 K. Using Wagner's formalism, the results of experiment were thermodynamically considered to determine the effect of a specific concentration of Cr on the activity coefficient of S in liquid iron."

Jan 1, 2014

By Masatoshi Ogasawara

Saganoseki smelter & refinery operated two flash smelting furnaces, producing a combined 330,000 metric tons per year (hereinafter mtpy) of copper. [n 1996, however, it successfully shifted to a single fumace operation while maintaining production at the same level. Since then, the production capacity has been further increased to the present 470,000 mtpy by technological improvements. Also, in order to reduce the converter load which represents a bottleneck in efforts to increase production, the matte grade was gradually increased and currently runs at 65 to 66% attaining the low copper content in the slag (hereinafter slag loss) of 0.7 to 0.8%. This ' paper introduces some improvements, recent operation results and thermodynamic analyses.

Jan 1, 2003

By Susumu Nagae, Hajime Ikeda

Recently, a number of mine development projects have been setback by social, economic and, environmental circumstances that had not been seen before. Many of these problems do not always originate from direct mine pollution. Typical examples of these are· conflicts between the exploration company and the local residents, sudden objections just before the development is to begin, and unexpected tightening of environmental regulations. The common background to these problems is expanding global environmental awareness. This includes complex factors ·such as the expansion of exploration to remote regions, the brisk activities of environmental NGOs, the increase of international environmental laws and, governmental policy changes. Today, the range of issues concerning mine development is widening significantly. The participation of local residents arid NGOs in the development planning, together with the company and government, has become essential for smoothly carrying out mine projects and making them more beneficial for stakeholders. Introduction The common image of the environmental problem with respect to mining is direct mine pollution, such as the collapse of tailings dams, pollution from refineries, and acid mine drainage. All over the world, the mining industry has made large investments in capital and technology to solve and prevent mine pollution, and these efforts have been making steady achievements. However in recent years, new cypes of environmental problems which are not originating directly from mine pollution are emerging frequently. Most of the problems are concentrated at the exploration stage to early stage of development, which have less impact on the environment. In the worst case, mining project may be forced to cancel and could cause serious damage to the industry because they could not collect their investment. I would like to take a general view of the examples of new types of trouble, their characters, background, and strategies against these problems.

Jan 1, 2000

By J. Huisman

With the introduction of ever-stricter environmental operating guidelines, capital expenditure restrictions and operational budget cutbacks, the biological method of SO2 removal becomes more and more attractive. Biological treatment of dilute flue gases is a more cost effective technology in comparison to conventional sodium hydroxide scrubbing. Although the investment costs for sodium hydroxide scrubbing is lower, the operational costs are significantly higher. In addition, the end product of the biological installation is sulfur instead of sodium sulfate; and no further wastewater treatment of the bleed from the biological installation is required since heavy metals are removed simultaneously. Another option for the treatment of SO2 containing gas at a sulfuric acid plant is the production of extra sulfuric acid of the discharged SO2 by applying an additional converter. Comparing biological treatment with this option shows much lower investment costs for the biological installation. Sulfur is produced which can be converted to sulfuric acid, so the bio-route will be more cost-effective than an additional converter. In principle, the biotechnological gas cleaning system is an integration of an absorber with a wastewater treatment facility. In the absorber, the SO2 containing gas is brought into contact with the washing water. The effluent absorber liquid contains a mixture of sulfite and sulfate that is converted into elemental sulfur. This conversion takes place in an integrated system; first, the sulfite/sulfate mixture is converted anaerobically into sulfide; secondly, the sulfide is converted aerobically into elemental sulfur. Subsequently the sulfur is separated and the water is returned to the absorber. Due to the buffer capacity of the washing water, removal efficiencies over 98% are possible. In addition to SO2 removal, it is possible to convert for example other bleeds streams such as scrubber acid or weak acid to sulfur in the same SO2 installation. Recent evaluations concluded that biological desulphurization of flue gases is not only economically attractive in comparison to convention sodium hydroxide scrubbing but also in comparison to gypsum producing systems and even seawater scrubbers. This paper describes the technological and economical viability of biological flue gas desulphurization.

Jan 1, 2005

By Lenny Winkel

With the aim to develop a solar-driven process for the extraction of copper from sulfide concentrates research on the decomposition of copper sulfides under inert atmospheres has been initiated. Thermogravimetric measurements on chalcocite (CuzS) revealed that copper is formed already at 1823 K. Chalcopyrite (CuFeS2) also disintegrates at this temperature, although at a lower rate. Copper and iron have been identified in the solid residue. The results confirm the feasibility of copper extraction by direct decomposition of sulfides under atmospheric pressure. The decomposition under inert atmosphere prevents generation of SO2, it also alters the behavior of volatile impurities during decomposition of copper sulfide concentrates. Chemical eqUilibrium calculations for chalcopyrite contaminated with enargite (Cu3AsS4) have shown that the absence of an oxidic slag allows for a complete evaporation of arsenic and subsequent separation from intermediate sulfides. The need to better assess the potential of direct sulfide decomposition has prompted the development of an experimental setup for studying the decomposition reactions. The experiment has been devised such that data on the decomposition kinetics and on impurity removal can be obtained at temperatures up to 2500 K.

Jan 1, 2003

By R. E. Aune

In the present work, a critical assessment of the thermodynamic information available for the ternary system Ni-W-0 has been carried out; This was complemented by experimental measurements of the standard Gibbs energy of formation of the ternary compound NiWO, by solid state galvanic studies involving Zr02-CaO solid electrolyte. The assessed thermodynamic data, together with the phase diagram information available in literature, were employed to generate the ternary phase diagram for the system Ni-W-0 in the temperature range 1073-1273 K. The calculation of the phase diagram was carried out by computer optimization according to the "CALPHAD" method. The computed phase diagram has been confirmed at isothermal sections by identification of the phases present in samples equilibrated at defined temperatures.

Jan 1, 1994

By B. R. Westphal

The Integral Fast Reactor (IFR) concept being developed by Argonne National Laboratory is based on the pyrometallurgical processing of spent nuclear metallic fuel with subsequent fabrication into new reactor fuel by an injection casting process. During fabrication, a dilute scrap stream containing uranium alloy fines and broken quartz (Vycor) molds is produced. Waste characterization of this stream, developed by using present operating data and chemical analysis, was used to evaluate different uranium recovery methods and possible process variations for the return of the recovered metal. Two methods, comminution with size separation and electrostatic separation, have been tested and can successfully recover over 94% of the metal. Recycling the recovered metal to the injection casting process was evaluated for the different economic and process impacts. The physical waste parameters and the important separation process variables are discussed relative to their effects on the viability of recycling the material. A discussion of the criteria that is being used to establish the acceptable operating limits is also presented.

Jan 1, 1992

By Shadia J. Ikhmayies

"Tin oxide (SnU2) thin films of thicknesses in the range 100-600 nm were prepared on glass substrates by vacuum evaporation at ambient temperature. The films were characterized by transmittance measurements, X-ray diffraction (XRD), scanning electron microscope (SEM) observations and energy dispersion X-ray analysis (EDAX). It is found that the films have high transmittance and non sharp absorption edges. XRD diffractograms showed that the films are amorphous and the SEM micrographs showed that the surfaces are smooth, uniform and well covered with the material. The EDAX analysis showed that the films are deficient in oxygen. Indirect optical bandgap energy and Urbach tailing in the bandgap was observed, and the width of the tail, which is related with disorder and localized states, was estimated.IntroductionTin oxide is an n-type wide bandgap semiconducting material with a direct bandgap energy of 4 eV and an indirect bandgap of 2.6 eV [1], where inherent oxygen vacancies act as an n-type dopant [2], Tin oxide thin films have been used for transparent electrodes in photoelectric conversion devices namely amorphous silicon solar cells, liquid crystal displays, gas discharge displays, etc. [3]. Perfectly amorphous thin SnO2 films show good electrical response to reducing gases in air and could, hence, be applied to construct semiconductor gas sensors where the metal oxide films function as a monograin-eqivalent active layer [4]. Amorphous SnU2 can also be used in extended gate field-effect transistors (EGFET) as a pH sensor, where the sensitive part is made of the SnO2/Al structure. This device can be used to detect and to quantify any kind of substance that can produce or consume protons, like an enzymatic reaction, therefore showing a large range of applications as biosensors [5].There are different methods to prepare SnO2 films, such as atomic layer deposition (ALD) [6], reactive magnetron sputtering [7], chemical vapor deposition [8, 9], dip coating [10], spray pyrolysis (SP) [3, 11-14], and evaporation [8], The thermal evaporation method was chosen to produce SnO2 thin films in this work because deposition by this technique does not present any compositional problems. In addition, it is a low temperature technique, which increases the probability of producing amorphous films. To increase this probability, the films were deposited at ambient temperature."

Jan 1, 2012

By D. M. Hausen

Multiple drill sections through many of the numerous breccia pipes in the American Eagle copper deposit at Copper Creek, Arizona, have been evaluated by means of alteration and geochemical data. Contoured plots indicate vertically plunging, concentric, cylindrical shells of alteration and mineralized rock that are similar in structure, geometry, magnitude and petrology to the San Manuel-Kalamazoo Deposit, located about 14 miles to the southwest. Both deposits are similar in dimension and consist of multiple, irregular, rod-shaped injections of porphyry into a granodiorite host. Analogous to the San Manuel-Kalamazoo Deposit, most of the porphyry plugs are oriented parallel to the cylindrical axis of the "ore shell". A continuously mineralized, elliptical shell, inferred from deep drilling, is capped by a flatter zone of copper mineralization. Above this flat zone, copper-bearing fluids were channeled upward along conduits that correspond with quartz-sericite "breccia pipes". At depth, zones of sericite and K-feldspar alteration products exhibit conformable relationships with the copper deposition. A "bullet-shaped" ore shell, with a nearly vertical axis, is proposed to explain the conformable zones of altered and mineralized rock. The "nose" or top of the "bullet" is 1800 to 2300 feet below the surface, and structurally controlled in part by steeply dipping Hi and ENE faults. If correct, this model suggests that the vertical ore shell may extend to great depth.

Jan 1, 1988

By John C. Taylor

With growing emphasis on energy conservation and increased concern over the presence of heavy metals in the environment, it is fortunate that most metals are readily recycled. In this respect, metals have a significant advantage over plastics and similar materials used as metal substitutes. For many years a secondary industry has processed scrap copper, nickel, lead and zinc to produce refined metal which has, to varying degrees, influenced the price and displaced the production of primary metal. This paper reviews some of the challenges the industry will face and the changes in process technology which will be required as pressure mounts to increase the amount of metal recycled. In the case of most base metals, this will have an impact on primary metal production; as the tonnage of metal recycled increases, the requirement for primary production, or new metal, will depend more and more on the growth in consumption.

Jan 1, 1993

By Robert P. Stevens

It is important for a refractory supplier to make systematic petro-graphic examinations of products which have been in service in the furnaces and kilns of customers. The petrographic examination of refractory service samples involves the microscopic study of polished and/or thin sections, supplemented by electron probe microanalysis, as well as the bulk chemical and XRD analysis of zones in the samples. The evolution of the A. P. Green Refractories Company petrographic laboratory is described, and the application of petrographic methods is illustrated in the examination of service refractories from a Portland cement rotary kiln and an AOD stainless steel vessel. The objectives of such studies are to assist the customer in the solution of his refractory problems, and to accumulate data which are of use in the design of improved refractory products.

Jan 1, 1981

By G. C. Yao

Branch and needle-shaped intermctallic compounds of iron, silicon and aluminum normally exist in the molten aluminum. If a suitable amount of manganese metal is added into molten aluminum, the shape of the intermallie compound particlcs may become lumpish and spherical. According to the difference in electric and magnetic properties of these impurity particles and molten aluminum, these impurity intermctallie compound particles can be separated by applying an alternating magnetic field. In this experiment the alternating magnetic field was formed by a "C" type loop with AC (50Hz) current. The inner vacuum of the fireclay refractory separator is 25>< 15" 130mm3 with a lateral baffle inside. The separator was put into the interspace of the "C" type loop. It was found that the longer the separation time, the larger the amount transferred of impurities. The amount of transferred impurities increases with the increase of separation time and intensity of magnetic field. The addition of manganese metal enhanees signifieantly the efficiency of impurity separation.

Jan 1, 2003

By Qinghai Pang

"With the increasing proportion of bituminous coal in blend coal, the safety of blend coal during pulverization and transportation is gradually being paid more and more attention. Therefore, the explosivity of bituminous pulverized coal (PC) with different volatile content from 25 to 38% was studied by measuring the combustion flame length after its injection into a glass pipe with the heat source installed in the center. The results indicated that high volatile content bituminous PC is apt to have higher explosivity. By blending different bituminous PC with 10% anthracite, the explosivity of bituminous PC showed a positive correlation with the proportion –OH radical. However, different bituminous PC seemed to have the same explosivity when the addition of anthracite increased to 20%. With the further increasing proportion of anthracite to 30%, the explosivity of bituminous PC with high –OH proportion became negligible while a weak explosivity of high –CH3 proportion bituminous PC still remained.IntroductionWith the increasing iron ore prices and decreasing steel prices, it has become critical for iron and steel enterprises to control the cost in ironmaking and steelmaking process. Blast furnaces (BF) are the main consumer in ironmaking process, which occupies 70% fuel consumption of total steelmaking process [1]. In this circumstance, any means necessary is taken by BF operators to lower the cost of iron in production. Coke and iron ore are the main expense in this process, who takes up a very high proportion in total cost. Pulverized coal injection (PCI) is the most efficient way to reduce coke ratio, which replace coke with relatively cheaper PC.At present, most of BF is injected with blend coal in the consideration of decent combustion property and quantity of heat. Simultaneously, bituminite and anthracite blending is an effective method to obtain blend coals with required composition and performance, such as volatile and ash content, etc. Nevertheless, a very huge gap was found between the price of bituminous coal and anthracite in some regions of China, in which the price of bituminite can be just 70% of the price of anthracite. Thus, iron enterprises in these regions attempt to possibly amplify the proportion of bituminite in blend coal. Increasing proportion of bituminite results in higher volatile content in blend coal, by which the safety of blend coal during pulverization or transportation was deteriorated.Relatively, coals with higher volatile content usually possess stronger explosivity, which means that volatile and explosivity may related to some extent. However, the relationship between volatile and explosivity is not of certainty for some PC with high volatile content around 40% was found to be inexplosive in comparison to the coals with lower volatile content. With the increasing proportion of bituminous coal in blend coal, investigations on the factors of PC explosivity have become more and more important. Therefore, bituminous coals with different volatile content were selected. The explosivity of blend coal and its relationship between volatile content and functionality was investigated in this research."

Jan 1, 2014

By Frederick T. Wallenberger

"Laser assisted chemical vapor deposition (LCVD) is a new containerless fiber process whereby growth of small diameter fibers or microstructures (microsprings, microsolenoids) occurs directly from the vapor phase. The laser beam has a focal point adjusted to coincide with the tip of the growing fiber inside the reaction chamber. Since the growing fiber is not in contact with reactor walls or foreign materials, it is chemically pure, and suitable for optical uses and uses requiring high structural uniformity. Continuous fibers and multifilament yams are possible. The use -of high reaction chamber pressures (1-10 bar) and a small wavelength Nd-YAG laser made it possible to fabricate small diameter fibers at growth rates >1 mm/s. This paper describes the synthesis of single crystal, polycrystalline and amorphous fibers by LCVD, and provides a comprehensive analysis of phase transformations occurring during their fabrication.IntroductionLaser assisted chemical vapor deposition (LCVD) is a new containerless fiber process [1-10] whereby growth of small diameter fibers or microstructures occurs directly from the vapor phase. The laser beam has a focal point adjusted to coincide with the tip of the growing fiber in the reaction chamber (Figure 1). The diameter of the growing fiber corresponds to that of the laser focus. Depending primarily on the laser energy (Le., the temperature at the growing fiber tip), it is possible to obtain single crystal, poly crystalline or amorphous fibers by this method.Since the growing fiber is not in contact with reactor walls or foreign materials, it is chemically pure, and suitable for optical uses and uses requiring high structural uniformity. Laser assisted CVD is a potentially continuous process; continuous fibers and multifilament yams are possible."

Jan 1, 1994

By Onuralp Yiicel, Ozlem Okur, Murat Alkan

"In this study, Co-Cr-Mo alloys were produced using a mixture of Co304, Cr203 and Mo03 powders with Al powders by a Self-propagating high temperature synthesis process. SHS is a process of material synthesis that has revealed a number of reactants combinations capable of much higher energy release than conventional explosives. Al203 is added to the mixture to decrease the adiabatic temperature of the system. The thermodynamic simulations and the calculations of adiabatic temperature were examined with FactSage 6.2. In the SHS experiments, different Co304/ Cr203/Mo03 ratios were examined, and their effects on the metal recovery and alloy compositions were carried out. The samples were characterized by using chemical analysis, XRD, XRF and SEM/EDS techniques.IntroductionSelf Propagating High Temperature Synthesis (SHS) has significant advantages compared to the high technology furnace applications, such as very short processing time, simple operation, low energy requirement and low cost [l, 2]. In a SHS process, the ignition starts the combustion and propagates throughout the reactant mixture yielding the desired product. However, the disadvantages of the process such as inhomogeneous or unreacted products due to undesirable reaction rates needs to be overcome by changing some parameters such as ignition temperature, particle size, additive, atmosphere etc. [3, 4]. This work aims to establish a scientific and engineering background in the production of some cast Co-Cr-Mo master alloys via SHS (Self Propagating High Temperature Synthesis) metallurgy which is attractive process technique regarding fast and low-cost production ability of cast alloys."

Jan 1, 2013

By M. Pakala, Z. Fan, Ray Y. Lin

Deposition of hard chromium coatings using electrodeposition is accompanied by emission of hexavalent chromium mists which is a carcinogenic. Hence alternative chromium deposition technologies are being investigated. Sputter deposition is a strong candidate to economically deposit hard chromium coatings in an environmentally friendly way. Chromium coatings of 2-3 µ m thickness were deposited on plain carbon steel coupons using RF magnetron sputter deposition. Depositions were carried out with 0 to 22 vol% nitrogen in the plasma. Structure of the coatings was studied using x-ray diffraction analysis With increasing nitrogen contents, formation of the two nitride phases was observed. The pure chromium phase was detected in coatings with up to 7% nitrogen in the sputtering gas. The solid solution of nitrogen in the pure Cr phase coating was identified by shifts of Cr x-ray diffraction peaks to higher d-spacing. The microhardness of the coatings deposited at a substrate temperature of 200°C showed an increase in hardness with increasing nitrogen content from 600 kgf/mm2 (5.9 GPa) at 0% nitrogen to I250 kgf/mm2 (I2.25 GPa) at 9.5 % nitrogen and a subsequent decrease in hardness to I 100 kgf/mm2 (11 GPa) beyond 9.5 % nitrogen in the sputtering gas. This corresponds to the formation of the hard Cr2N phase, at 9.5 % nitrogen, and CrN phase, at I5.7 % nitrogen. The reported bulk hardness values of Cr2N and CrN are I600 kgf/mm2 (I5.7 GPa) and I 100 kgf/mm2 (11 GPa) respectively. For pure Cr phase coatings, there is a slight increase in hardness for coatings deposited at 7. I % nitrogen from that without nitrogen in the sputtering gas. This could possibly result from the solid solution strengthening of the Cr lattice by nitrogen. For films deposited at 200°C, phases of the deposited films seem to be the overwhelming factor in controlling the microhardness.

Jan 1, 1998

By Hong-ying Xia, Bao-bao Wang, Jin-hui Peng, Bing-guo Liu, Li-bo Zhang, Zhi-qiang Li

Based on optimization using response surface methodology designed by Box- Behnken, to study the interaction of wet industrial salt with moisture drying temperature (50-90 ); duration (10-50s); and the weight of the materials (20-60g). The results show that: the experimental parameter conforms to the quadratic equation model to influence the moisture content and the dehydration speed., in analyzing the significance and the interaction of various factors, the optimum by the Design Expert software conditions for drying with microwave radiation include temperature of 90 , duration of 10s, and sample mass of 26g. Verified by experiment, the moisture content after drying is less than 0.25% and the dehydration rate reached 1.37g/min, between the predicted value and the actual value confirmed good fitting degree.

Jan 1, 2015