Search Documents

TiO2 and Ti/TiO2 thin films were deposited on a quartz substrate by laser ablation of Ti02 and Ti targets using Nd:YAG pulsed laser. After sulfurization of the Ti02 film in H2S or CS2 gas at 1273 K for 1 hour, the surface atomic structure was changed. Furthermore, the Ti/TiO2 film was successfully prepared by the subsequent ablation of Ti and TiO2 targets. The morphology and structure of the films were characterized by XRD, XPS and AFM analyses.

Jan 1, 2003

By T. Nakamura

TiO2 and Ti/TiO2 thin films were deposited on a quartz substrate by laser ablation of TiO2 and Ti targets using Nd:YAG pulsed laser. After sulfurization of the TiO2 film in H2S or CS2 gas at 1273 K for I hour, the surface atomic structure was changed. Furthermore, the Tirri02 film was successfully prepared by the subsequent ablation of Ti and Ti02 targets. The morphology and structure of the films were characterized by XRD, XPS and AFM analyses.

Jan 1, 2003

Roasting treatments were investigated to remove arsenic from a nickel concentrate. The main arsenic minerals and their proportions in the concentrate were niccolite (NiAs)-50%, gersdorffite (NiAsS)-40% and arsenopyrite (FeAsS)-10%. Thermal analysis showed that gersdorffite and niccolite began decomposing when heated above 640 and 830°C respectively. The maximum roasting temperature was limited by agglomeration of the concentrate above 900°C. A small vibrated bed reactor was used to investigate the effects of temperature and gas flowrate, the latter to sweep away evolved arsenic. At 900°C, 24% of the original arsenic remained in the concentrate. SEM examination of the calcine showed that the residual arsenic was associated with the calcium in the gangue minerals. Additions of sulphur (either as elemental sulphur or from pyrite) facilitated the decomposition of the arsenic-containing minerals, decreased reaction with calcium in the gangue and produced calcine containing 4-6% of the original arsenic. Treatment with chlorine during roasting was effective in reducing the arsenic content to similar levels. Generation of chlorine in the bed by sulphation of CaC12 also produced encouraging results. Arsenic, Nickel Concentrate, Roasting, Chlorine, Sulphur, Gersdorffite, Niccolite

Jan 1, 2005

By Daniel C. McLean

Extraction data for Cu, Zn and Fe were obtained from 4.5" and 10" columns using massive sulfide ore and natural acid mine water. The purpose was to determine if recycling of solution through the column would produce leach liquors of 4 g/l Cu and Zn at extraction rates of 1 g/l per pass at typical flow rates of 0.002 to 0.006 gpm/sq.ft. Test results exceeded expectations. Cu and Zn concentrations of 4 g/l were obtrained within 4 to 6 cycles. Concentrations greater than 6 g/l Cu and 8 g/l Zn were reached within 10 cycles. Concentrations of greater than 40 g/l of Fe and free sulfuric acid were obtained with no decrease in biological activity being observed. No reagents were used.

Jan 1, 1995

By Robert H. Hsu

Palladium finely dispersed in a substrate of kieselguhr, Pd/k for short, has been successfully used for hydrogen storage, separation and pumping for a number of years at the Savannah River Site (SRS). Recently SRS has developed a new pd/k flow through bed (FTB) prototype for separating hydrogen from other gases and simultaneously storing the hydrogen on palladium. The FTB uses single-pass liquid nitrogen cooling during hydrogen absorption/separation/storage and electrical heating for desorption/unloading of hydrogen. Fourteen absorption-desorption or loading/unloading cycles using hydrogen have been conducted with the new FTB prototype. Test results show that all design performance objectives have been successfully achieved: recover 295% of hydrogen gas from feed gas, produce 99.9% hydrogen product gas and < 5% hydrogen in discharge gas. This paper will discuss characteristics of the palladium-coated kieselguhr or diatomaceous earth, design and operation of the FTB, and results of performance tests such as separation efficiency, hydrogen storage capacity and system heat transfer characteristics.

Jan 1, 2002

By Walter Curlook

An improved process of hydrometallurgical treatment of laterite ores of the limonitic type for the recovery of nickel and cobalt using sulphuric acid has been developed and patented [I]. The major improvement is brought about by recycling a significant portion of the "mother liquor" emanating from the pressure leaching reaction back to the feed preparation stage thereby substituting for all or at least a major proportion of the fresh water that must be added. The amount of process effluent waters is correspondingly reduced. Concomitantly with the major savings in fresh water requirements, a degree of reduction in new sulphuric acid requirements is effected, along with a savings in limestone and lime required for subsequent neutralizations. Keywords: Acid pressure leaching; Nickel laterites

Jan 1, 2004

By James R. Myers

A source of clean gas containing sulfur dioxide and sufficient oxygen for convers.ion to sulfur trioxide ?is essential to the production of sulfuric acid. S02 containing gases obtained from roasting sulfide ores are heavily contaminated with inorganic dust and volatile impurities. If not removed, these contaminants will reduce product acid quality, foul the catalyst beds and mist eliminators, and accelerate equipment corrosion. This paper reviews conventional gas cleaning systems for metallurgical acid plants, followed by a discussion of modern systems utilizing DynaWave Scrubber technology. This technology is based on a unique approach to? gas scrubbing that can concurrently accomplish several gas cleaning/processing tasks scrubbing liquid is injected into the gas stream to create. a "Froth Zone". This is a region of extreme turbulence, with a very high rate of liquid .surface renewal. It efficiently removes both particulate matter and gas contaminants, and is also a cost effective quenching device for gases as hot as 1250º C. Smelter

Jan 1, 1992

By John Fallavollita

Conventional gas atomization produces powders that vary widely in size distributions and microstructures, thus making it very costly to produce powders tailor made in a narrow size distribution and microstructure. Furthermore, it is difficult to determine the relationships between atomizer operating conditions and resulting powder characteristics. The Impulse Atomization Process (IAP) was developed at the Advanced Materials and Processing Laboratory to produce powders with narrow size distributions. Powders produced by the IAP were reproducible and their sizes could be easily controlled by adjusting experimental conditions. Characteristics of Zn, Sn-Pb, AI-Cu, and Cu powders will be described to illustrate the flexibility of the process to tailor-make powders.

Jan 1, 1994

By Jiann-Yang Hwang

Hydrogen storage is a critical issue for the hydrogen economy. Current storage technologies are not able to meet the combined gravimetric, volumetric, and system cost targets set by the Department of Energy. To solve the problem, the development of a new material - perhydride ? is proposed. Perhydrides are defined as materials that contain more hydrogen atoms in their molecules than conventional hydrides do based on the valence. This concept is supported by the versatile bonding capability of hydrogen and the recent discoveries in the chemistry of hydrogen clusters.

Jan 1, 2006

By R. C. Chaturvedi, S. B. Padwal

"Padwal and Chaturvedi have developed the model based on M-K theory, considering Hosford's yield criterion and critical thickness strain criterion"" to predict the sheet metal forming limits under simple (constant) strain ratio paths. This analysis has been extended in this paper to predict the sheet metal forming limits under complex strain paths. The effects of exponent ""a"" in Hosford's yield criterion and strain paths on the forming limits under complex strain paths are studied using this analysis. The predictions of the present analysis are compared, both for simple and complex strain paths, with experimental results of Ishigaki for A.K. steel and also with the predictions of Rao and Chaturvedi's model. The quantitative analysis of the error in predicting the forming limits has also been carried out using a method suggested by the authors earlier.1. INTRODUCTIONThe constant strain ratio condition has been assumed in the theories developed for prediction of forming limit diagrams (FLO). In actual forming operation, this condition is seldom satisfied. Even in the case of simple single stage press formed components, the strain path becomes curved and non-linear. In the case of pressings with complex shapes, or multiple stages of forming, the changes in strain path are more pronounced and even abrupt.Experimental study of the forming limits, under two stage strain paths, by Ishigaki [1], has shown that the forming limits are path dependent. It has been observed that the forming limits lower than that under simple strain paths, may be obtained under certain strain paths (when the first stage strain path is either equibiaxial tension or uniaxial tension, followed by the second stage strain path as plane strain). Rasmussen's work [2J, on the theoretical study of forming limits under curvilinear strains paths, has shown that a large drop in formability can result from very small changes in strain path. Thus if a deformation process gives rise to failures due to plastic instability, the failure is not necessarily due to insufficient formability of the material. In such cases, FLOs based on constant strain ratio path should not be used directly in predicting the success or failure of the forming operation. Thus the knowledge of forming limits under complex strain paths is of great importance to the interpretation of press-shop problems."

Jan 1, 1994

By F. Qian

Direct impingement of molten metal baths by a gas jet is commonly encountered in such processes as BOF and electric arc furnace steelmaking. Shape and local fluid mechanics in the impinging region is important because it determines the interaction of the metal pool with the surroundings. Goal of the present work is to characterize and understand the interfaces at the impinging region. Using a physical model consisting of water/corn oil and water/kerosene as surrogates for metal/slag, interface shapes for slag-gas, slag-metal and metal-gas are investigated. Influence of transport properties of the two liquids on the shape and flow fields are also experimentally determined under various impinging jet conditions, namely jet momentum and jet height. The viscosity of the slag layer (corn oil or kerosene) has the most significant effect on the interface shape and the induced flow fields. The interface shapes were measured both photographically and by using a surface- tracking resistance probe. The limiting condition at which the jet breaks through the corn oil or kerosene layer and reaches the water layer was determined experimentally

Jan 1, 1994

By Sergio T. Amancio-Filho

FricRiveting technique is an alternative new spot joining process developed for thermoplastic-lightweight alloy structures. In this technique a cylindrical metallic rivet is used to join one or more thermoplastic / metal components by means of plasticizing and deforming the tip of the rotating rivet through frictional heating. Advantages of this new technique are e.g. short joining cycles, minimal sample preparation, absence of environmental emissions and enhanced mechanical performance in comparison to base materials. Qualitative and quantitative synchrotron X-Ray microtomographic and light optical microscopic analysis of a case-study joint on aircraft materials polyetherimide and aluminum 2024 showed that joint strength is mainly dependent on aspect ratio of the rivet (geometrical dependence) and quality of joint, (microstructural dependence), whereby increasing aspect ratios and lowering the percentage of defects usually yield improved strength.

Jan 1, 2009

By Oleksandr Liaskovskiy, Sergey Beringov, Sergiy Yatsuk, Timur Vlasenko, Iryna Buchovska

"Working with solar-grade silicon for solar cells application usually meets some difficulties in comparison to polysilicon produced by Siemens method: higher impurities content leads to lower yield, worse electro-physical parameters and poor performance in solar cells application. However some adjustments in ingot production can show significant improvements in quality of final product: crystalline wafers and cells.Recent investigations have shown that solar-grade silicon is suitable for high effective production process such as mono-like multicrystalline wafer production. Production-scale lots made at Pillar show promising results for solar-grade silicon application: high-quality wafers with significantly big crystalline grains of <100> orientation.IntroductionThe standard technology of producing multicrystalline silicon ingots by directional solidification method in quartz crucibles has a number of disadvantages resulting in limited efficiency of solar cells made of multicrystalline material: crystallites of multicrystalline ingot are relatively small (down to 5 mm size), grain borders of crystallites contain parasitic impurities such as metals, silicon nitride etc., crystallographic orientation of crystallites is random. The listed deficiencies are an integral characteristic of the technology which affects the efficiency of solar cells, such as presence of solar cells with low efficiency even at a high level of average efficiency, problems with shunted cells, silicon nitride inclusions, which adversely affect cell efficiency and are centres for silicon carbide formation, impossibility of application of high effective alkaline texturing etc. Also with regard to the targets set by photovoltaic to reduce the cost per Wp in the nearest future, standard technology of multicrystalline silicon ingots production by directional solidification faces certain challenges some of which are hard to overcome due to rather low efficiency of solar cells made of multicrystalline wafers. Therefore alternative methods of multicrystalline silicon production for photovoltaic application having a number of advantages in comparison to traditional technology are developing rapidly."

Jan 1, 2012

By Kamal Adham

Hydrochloric acid is used as lixiviant in such hydrometallurgy processes as synthetic rutile production and nickel extraction. The intermediary metal chloride is normally roasted to release gaseous HCl and a solid metal oxide. A large amount of fuel is required for this thermal regeneration, mainly to vaporize the water content of the feed solution. To conserve fuel, some energy recovery from the off-gas is currently achieved, but the fuel costs can further be reduced by process optimization and energy recovery from the gaseous, aqueous and solid products of the regenerator. Here, first the existing limitations to fuel efficiency in the industrial scale HCl regeneration roasters are described. Then, for the case of a dilute feed solution, options for pre-evaporation and fuel minimization are modeled and compared. Finally, energy recovery technologies including heat pumps, acid heat exchangers and solid waste heat boilers are described, and their potentials as the heat source for pre-evaporation of the feed are evaluated.

Jan 1, 2003

By Ovidiu Pasca

Several improvements in converter equipment and operation at BHP Copper have reduced the converter cycle time as necessitated by an increase in flash furnace output. The resulting higher intensity performance of the Peirce-Smith Converters has had a major impact on the dust handling and off-gas cleaning systems. This paper describes work carried out on the design of a new converter hood with particular reference to the thermal analysis and hood performance aspects. Changes in converter cycle time and campaign life as result of the process and equipment improvements are discussed in a separate paper.

Jan 1, 1999

By Itavahn Alves da Silva, Jose Dimas de Arruda, Amanda Aparecida Fátima Arruda, da Silva de Souza, Carlos Antonio da Silva, Varadarajan Seshadri, Samuel

The knowledge of the flow field inside a continuous casting mold is essential to improve operational efficiency of the process and also to achieve better inclusion control. Physical modeling, PIV technique and CFD have been employed to assess the velocity distribution in the metal- slag interface region in a slab mold. The analysis of results shows how higher casting velocity and lower immersion depth of submerged nozzle can lead to higher turbulence in the slag-metal interface. The effects of density difference between slag and metal and interfacial tension between the phases have been highlighted.

Jan 1, 2016

By Varadarajan Seshadri

The performance of mould fluxes in satisfying its quality requirements can have a significant effect on the efficiency of the continuous casting process and on the surface quality of the products. This performance is affected by various parameters including the characteristics of the mould fluxes, the quality of the steel being cast and the operational conditions of the caster. The extremely complex relationships involving the parameters mentioned above make it very difficult to have simple criteria for selecting mould fluxes for casting a certain grade of steel in a continuous casting machine. These difficulties led steelmakers and mould flux suppliers to select mould fluxes based mainly on plant trials. In the present work, a software to help in the analysis and development of mould fluxes for continuous casting was developed. This software includes several models for prediction of mould flux viscosity and consumption. A mathematical model was also used to predict the heat flux through the mould flux. The proposed methodology was applied to continuous casting of crack sensitive steels. Some of the results given by this software are presented, discussed and compared to plant data.

Jan 1, 2003

By Xinghui Meng

The recovery of platinum and palladium from automotive catalysts has been investigated by leaching in iodide solutions with oxidants including oxygen and iodine in an autoclave. An ammonium salt was presented in a neutral leaching solution as a key leaching reagent to achieve high recoveries of the platinum group metals (PGM). The effect of temperature, and concentrations of oxidants and of ammonium salt on the recovery of PGM was examined. Under the experimental conditions studied, the recovery of platinum and palladium was found to be greater than 95%. An economical assessment of this process has also been examined and discussed.

Jan 1, 1995

By T. Manlyama

The Tamano Smelter of Hibi Kyodo Smelting CO., Ltd. went into operation in 1972. The Flash Smelting Furnace that was originally adapted was equipped with electrodes that were attached to the settler substitute of the slag cleaning furnace. Later the development of our own original coke combustion technology was promoted and a new Tamano Type Flash Smelting Furnace (T-FSF), without electrodes, was put into operation in 1988, T he technology of coke combustion and combustion the burner have continued to improve. As a result the copper losses in the Wag have been reduced as well as a stable operation has been achieved, Furthermore; this has been accomplished while increasing the concentration feed and the matte grade. The current objective is to continue to strive for high matte grade operation and to raise production efficiency while paying attention to the important subject of copper losses in the slag. In this report, the data related to the copper loss in the slag reduction are presented along with the influence of the thickness, settling time and coke. The recent operation conditions of the T-FSF are also presented.

Jan 1, 2003

By K. S. Jeong

Since the start-up of the Onsan Smelter in 1979, LS-Nikko Copper has grown into a competitive smelter through continuous development. Several environmental improvements have been carried out, in particular, intensive investments in reducing SOx emissions, such as de-sulfurization plants, fugitive gas capturing and TMS(Tele Metering System). In addition, in recent years LS-Nikko Copper has spent more than 10 million USD every year to improve environmental conditions. In order to be a global leading smelter in every aspect especially environmentally, LS-Nikko Copper plans to inspire environment-friendly minds, co-operate with shareholders, and participate in global conventions. This paper describes the environment improvements carried out at Onsan and briefly introduces a sustainable vision for a green smelter.

Jan 1, 2006