Search Documents

By David J. Roha

"The harsh environment of the Carbothermic Aluminum process makes necessary numerical modeling as a means of process visualization and understanding. A brief survey of the various numerical models, with emphasis on CFD, applied in the development of the process is presented.IntroductionThe environment of the Alcoa Carbothermic reactor is necessarily a harsh one, with temperatures approaching 2100 °C and plenty of reactive dust and vapors. As such, it is difficult to directly observe what is actually taking place. Thermocouples can last for a few minutes but are eventually destroyed. The openings to optical pyrometers become occluded with dust and condensation. Graphite sheathing embrittles, reacts away or becomes clogged with condensate. Dip-samples on steel rods are routinely taken, but their interpretation is often unclear.Those measurements that can be reliably taken are invaluable, but often do not provide a complete picture. Therefore from the very inception of the project both physical and computer based models have played an important role. Modeling provides an intuitive understanding of the processes that might be taking place and in very many cases approach quantitative prediction. I will briefly touch upon computer-based modeling performed at Alcoa over 12 years of the Carbothermic project, with special emphasis on CFD. The explanation of physical models is perhaps best left for those with the greatest familiarity with them"

Jan 1, 2012

By Jinxing Ji

The thiosulfate lixiviant system for leaching of gold has been under extensive investigation for nearly two decades and consists of ammonium thiosulfate, copper and ammonia. There are several challenges with this system. The occurrence of ammonia must be taken into account from a health and hygiene aspect in the workplace, and also from an environmental perspective with significant levels of ammonia and copper in the tailings. Copper accelerates the leaching rate but causes excessive thiosulfate degradation. A new lixiviant system that has been investigated consists only of sodium thiosulfate without copper and ammonia. Gold leaching is carried out in an enclosed reactor with slightly elevated oxygen overpressure and temperature. Extensive leaching experiments were carried out to minimize thiosulfate degradation and polythionate formation while maximizing the gold extraction. For the preg-robbing carbonaceous ore sample tested, gold leaching was essentially complete within six hours and the thiosulfate consumption was lower than in the typical ammoniacal thiosulfate system. The gold thiosulfate complex in the pregnant leach solution was found to be quite stable under ambient conditions. This new leaching system has the advantages of being more environmentally friendly, has a shorter residence time, lower thiosulfate consumption, lower oxygen consumption, and is easier to control.

Jan 1, 2003

By J. Ipinza

The slime formation with several metallic impurities from acidic electrolytes of copper has been studied. On fresh Pb-Ca-Sn anode surface firstly the formation of PbSO4 takes place, then, it is transformed in the conducting PbO2, which covers the anode surface. It has been experimentally established the formation of a manganese dioxide double layer at the anode; this double layer was always composed of a thick external layer of non-adhering and easily removable scales, and of a thin internal layer, which adheres relatively well to the surface of the electrode. It was found that manganese dioxides present in the slime were of different nature: a non-adhering layer produced by electrolysis (-MnO2) on the PbO2 surface and a pure chemical precipitation in the solution (-MnO2). When iron is present in the electrolyte on this last layer of manganese, lead sulfate was found. In the case of arsenic and antimony in the electrolyte the slime generated was found to be lead sulfate and amorphous compounds of those ions. The lower slime generation in Chilean EW plants could be due to the lower contents of iron and manganese in the electrolytes. It was found that this slime formation rate not only is due to the electrolyte composition but also to the poor control of operational parameters at EW plants.

Jan 1, 2003

By Ennio Bonetti

The technological applications of MgH2 hydrides for hydrogen storage demand the overcoming of some critical issues: an improvement of the reaction kinetics and a reduction of the desorption temperature. The synthesis of nanocrystalline MgH2 by reactive milling and inert gas condensation and a proper metal catalyst addition, constitute recently employed strategies. In the investigation of the hydrogen short and long-range dynamics, sorption kinetics and nanostructure stability, the mechanical spectroscopy offers some specific advantages. In the present research this technique was employed with other experimental approaches (XRD DSC) to investigate relaxational and structural damping processes in nanocrystalline MgH2 with added catalysts (Fe). Time/temperature variation of the dynamic elasticity moduli and mechanical quality factor are correlated to hydrogen anelastic relaxation processes and concomitant structural transformation of MgH2 to Mg associated to long range H diffusion. Results are discussed with reference to microstructural modification strategies able to assist hydrogen release.

Jan 1, 2006

By Anthony C. Mulligan

Metals have historically been used in mining since they offer an excellent combination of hardness, toughness and cost and can be fabricated to form a variety of shapes. However, for many applications the metals used today have limited performance in the environments in which they are needed. This is particularly true for geothermal environments where the brines are highly siliceous causing corrosion and accelerated wear of many components. Geothermal sources are increasingly being explored for their high thermal value as well as possible sources for future minerals. While advanced ceramics have historically been expensive to produce in comparison with metals, they offer significantly greater corrosion resistance and hardness and can improve the overall performance when used in selected ?problem? areas. One of the major drawbacks in the use of ceramics in high impact areas has been their brittle nature and propensity to fracture and spall (fail) when loaded. Recent advances in the fabrication of ceramics have combined hard (strong) ceramics with more ductile ceramics in a architecturally designed microstructure, thus allowing ceramics to perform well in these high impact regions. Additionally, ceramics are significantly more inert to corrosion from either alkaline or acidic environments and can typically be used for significantly longer periods in these environments than their metallic counterparts.

Jan 1, 2006

By Chuan-fu Zhang

In present work, the physical properties of molten FenO-MgO-CaO-SiO2 slags were measured .It is shown by the results that when the slag composition is as follow: MgO 8%~12%, CaO 2%~8%, Fe/SiO2 1.2~1.6, the viscosity of the slags decreases with the increase of temperature. When the Fe/SiO2ratio and the MgO content are fixed, the electrical conductivity increases and the viscosity decreases as CaO content increasing, while the content of CaO exceeds 6% its influence weakens. When the MgO content is 11% and the CaO is 6%, the viscosity of the slag decreases markedly as the increase of Fe/SiO2 ratio. Its influence to viscosity is inconspicuous when the Fe/SiO2 ratio exceeds 1.5. When the CaO content is 6% and Fe/SiO2 is 1.2, the electrical conductivity decreases with the increase of MgO content as temperature is below 1290, but increases when temperature is above 1290. When the MgO content is 11% and the Fe/SiO2 ratio is 1.2, the electrical conductivity increases with the increase of CaO content. When the CaO content is 6% and MgO content is 11%, the electrical conductivity increases as the increase of Fe/SiO2 ratio, while its influence weakens as the temperature increases continuously. The electrical conductivity rises when temperature increases at any slag content. The melting temperatures of FenO-MgO-CaO-SiO2 semi- synthesis slags from this work were below 1290.

Jan 1, 2006

By Krishna Kumar

"Growth of electronics waste (e-waste) and lack of appropriate disposal mechanism are the great concern for developing countries like India. The domestic generation of e-waste in India is rapidly growing with the development. The imported substance is also substantially contributing to the e-waste inventory. Recycling of e-waste is mainly carried out in unorganized units in India. The primitive recycling technique used by the unorganized sector is a great threat to the environment and the health of the operators involved in these profession. Therefore, improvement of technology used by these units towards a cost effective, environmental friendly alternative could be the solution to the present crisis. Few initiatives of recycling have, however, come up in recent years in organized units. The precious metals are still recycled in the developed countries. This report discusses the inventory, technology status, legal legislative and existing practices of e-waste management in India.1. INTRODUCTIONInnovation, research and development in the field of electronics and information and communication technology (ICT) lead to convenient, independent human life. Consumption of electronics and hardware products has enhanced by manifold. Electronics and hardware sectors have, thus, become the fastest growing sector in the world. Faster obsolescence of these products is forcing users to replace products with an advanced technology. Life cycles of these products are few years. Discarded electronics products are, therefore, accumulating alarmingly in our society. Electronics waste (e-waste) is a crisis not only due to its volume but also for presence of its toxic ingredients, like heavy metals (e.g. lead, mercury, cadmium, hexavalent chromium) and flame retardants such as poly brominated biphenyles and poly brominated diphenyles ether. These substances create potential occupational and environmental health hazardous."

Jan 1, 2011

By K. Noda

Tamano Smelter of Hibi Kyodo Smelting Co., Ltd. is carrying out a low cost production using a Tamano Type Flash Smelting Furnace (T-FSF), which is an improved version of Outokumpu Type Flash Smelting Furnace but without slag cleaning furnace and also by developing its own coke combustion technology. Coke combustion technology that is the basis of the system has been improved several times and, at present, it has evolved to a stage where it can be reproduced on the Computer guided system for Coke Combustion in the T-FSF (CCCT) using a general- purpose computer. This CCCT is featured by 'its trend control and predicting function, and an operator can freely control the operation parameters so as to control the operation flexibly. We have recently developed an overall energy reduction system covering the Smelting Plant to Sulfuric Acid Plant, which we call an Optimum Low Cost Operation System (OLCO) to reconsider the energy costs including coke, heavy fuel oil, and electric power. In this report, we would like to present the recent operation of T-FSF based on CCCT as well as the optimum energy operation utilizing OLCO system.

Jan 1, 2002

By S. J. Kohut

Until recently SX-EW technology has only been used to produce conventional cathode for the cyclical commodity marketplace. Unlike electrorefining, SX-EW lends itself to the integration with the downstream manufacturing technologies for direct mine site production of value added products. The integration of SX-EW and downstream manufacturing results in the elimination of redundant process steps, the cost savings, and the access to value added product markets which can buffer the producer from swings in the cathode market. SX-EW production of copper powder and powder-based products has been demonstrated at the pilot plant level. The SX-EW process has been successfully redesigned to meet the more specific demands of engineered products. Challenges include the solution purity, the cell ventilation, the high current density operation and the product handling. Successful demonstration of mine site production of value added SX- EW products opens up new non-commodity marketplaces to the mining industry.

Jan 1, 1999

By E. R. Vance, D. R. M. Brew

"Historically, Ordinary Portland cement has been the preferred medium to immobilise arsenic. However, arsenic in cement gives rise to calcium-arsenic phases and their known decomposition to calcium carbonate and arsenic trioxide via atmospheric carbonation raises serious questions about the long-term suitability of cement for arsenic immobilisation. Alternative matrices such as low-temperature ceramics (LTCs) potentially offer superior resistance towards carbonation owing to the absence of calcium. Consequently, the potential for arsenic immobilisation using LTCs has been investigated. Both AsIII and AsV have been incorporated and samples assessed according to a standard leaching protocol. AsIII persists in the porewater of alkali-bonded LTCs as sodium arsenite rendering them unsuitable for immobilisation. Thermal treatment of these LTCs to consolidate the microstructure and reduce open porosity resulted in sodium-rich cryptocrystalline matrices that leached arsenic and sodium readily. The omission of sodium in acid-bonded LTC formulations resulted in leach data that were close to the target value of 5 µg/ml in Toxicity Characterisation Leaching Protocol tests.IntroductionArsenic is a carcinogenic substance and its adverse effects of on humans, flora and fauna have been well documented [1-5]. As a consequence, many papers have been written on the prospective handling of arsenic-bearing waste. These can largely be divided into: (a) cleanup of arsenic-contaminated water using bacteria, precipitation, and/or UV irradiation to generate arsenic-rich sludges for subsequent immobilisation; (b) cleanup of arsenic-contaminated soil via chemical extraction for immobilisation of the As concentrate; and (c) immobilisation of industrial waste contaminated with As."

Jan 1, 2008

By Vladyslav M. Sokolov

The cost effective and environmentally friendly recycling technology was developed and tested. It enables utilization of the fine nickel-base superalloy scrap in a form of heavily oxidized scarfing granulates. The process of granulates generation was discussed in details. Their properties were investigated. The results of literature search showed anticipated sufficient improvement of the properties of cast iron by its alloying with the elements from the scarfing granulates. The novel alloying approach is based on the two stage reduction operation. Firstly thegranulates were partially reduced in a solid state by their exposure with powdery carbon at the range of 1550 ? 1700°C. Then the gotten product was efficiently introduced into liquid iron since it has a form of fine natural agglomerates for arranging the optimal conditions for reduction of the granulates. The thermodynamic evaluation demonstrates higher reduction efficiency of carbon and silicon dissolved in iron than of the same elements in a form of the separate phases. The considered process partially provides itself by energy since the reaction of reduction of the chromium oxide by silicon dissolved in liquid iron has exothermal character. The mostly complete extraction of Ni was received. The sufficient reclamation of Cr was gotten at the same time.

Jan 1, 2006

By Florian Kongoli

While calcium ferrite slags have been successfully used in continuous copper converting for the last 30 years, ferrous calcium silicate slag was proposed about 8 years ago as an additional alternative for copper smelting. Although both slags are normal extensions of each other their phase relations have not been completely clarified. In this paper the liquidus relations of both slags have been quantified at various areas that cover both of them. The existing experimental data have been first reviewed and discussed in relation to the solidification procedure. An original physical model is then used to predict various diagrams of the liquidus surface of both slags. It is shown that the ternary liquidus diagrams normally used for FeOx-SiO2-CaO system are not suitable for industrial slags. The new model diagrams of Fe/CaO versus SiO2 and Fe/SiO2 versus CaO as well as Fe/CaO versus Temperature and Fe/SiO2 versus temperature are proven to be much more convenient for ferrite and ferrous calcium silicate slags. Based on these diagrams the effect of SiO2 and CaO on the melting temperature is quantified. The effect of Cu2O is also quantified through the model. Some Fe/CaO versus Cu2O and Fe/SiO2versus CaO at various copper contents are predicted and the results show good agreement with the experimental data. It is also shown that in the presence of liquid copper, Cu2O is dissolved in the slag depending on the oxidation degree of the system and might lower the liquidus temperature. Some discussions are also presented taking into account plant observations and important conclusions are drawn for copper smelting and converting

Jan 1, 2006

By J. Partinen

Drying is a unit process which has numerous applications in metallurgical process industry. Kumera Technology Center, being a worldwide equipment and process supplier, has developed sophisticated solutions for both direct and indirect drying. In conventional direct drum drying, the energy is taken from combustion of fossil fuels, requiring energy input and emitting considerable amount of off gases. In modem copper smelters, thermal energy from the off gases is recovered in waste heat boilers making the steam available. Using that steam as the energy source for concentrate drying, the total volume of off gases can be considerably reduced and releasing of harmful combustion gases into the atmosphere can be avoided. Kumera Technology Center has recently developed and promotes a new steam drying process for drying of copper concentrates. In the development of the new dryer, Kumera's approach has been to combine the best properties of both the steam dryers and the drum dryers. In the design special attention has been paid to overcome problems of excessive wear and clogging and to reduce the required maintenance operations. In this paper the environmental issues and energy consumption related to both direct and indirect drying processes are discussed. The estimated operation costs and emission levels are compared, based on calculations and the data collected from industry. Finally, the development project of the Kumera Steam Dryer is briefly reviewed

Jan 1, 1999

By J. M. Casas

This work presents the development of an ionic equilibrium model and its use to simulate the distribution and concentration of chemical species (speciation) in sulfuric acid - cupric sulfate solutions in the 0-2 pH range, 0.1-10 gpl copper concentration range and 15-45°C temperature range. The model consists of a set of equations which represent the equilibrium relationships for the ionic reactions and the mass balances for the components present in the system. The effect of ionic strength was taken into account by correcting the equilibrium constant in concentrated solutions. Several species can be formed at different pH and temperature values, the principal being: HSO-4, SO42-, CuSO4(aq), Cu2+, and H+ in order of increasing solution acidity. Simulations show that concentrations are highly dependent on pH. The sulfuric acid speciates mainly as bisulfate ion (HS0-4) and hydrogen ion (H+) at pH values lower than 1. The model presented in this work can be applied to predict and analyze the solution composition in electrolytic copper processes such as electrowinning, electrorefining and electrodialysis, as well as the purification of various industrial solutions.

Jan 1, 1999

By C. Twigge-Molecey

All projects that are implemented, have been given corporate go-ahead on the basis of a set of clearly defined targets. These are typically a production goal at a capital cost, operating cost and production schedule, that will yield an acceptable return on investment by the companies internal criteria. The challenge for the implementation team is two-fold, firstly to properly define the project criteria prior to board approval and secondly to deliver an operating facility that meets these objectives, in particular the ROI. The paper addresses the issues a project team and the company management must address for a successful project. Key questions that will be explored are: ? What is the status of key technologies? Are they well proven in commercial practice, completely novel or in between? ? Is the project schedule driven by market constraints or cash flow constraints? ? Are the risks of fast tracking worth the potential rewards? ? For a retrofit project, are all the technical and production interfaces and issues known at the time of approval to proceed? ? How much should be invested in technological development and engineering and at which phase? ? For an owner-operator, how much responsibility is it wise or appropriate to push down to vendors? The answers to these questions for a specific project will define how you go about a project, the resources required, the contracting strategies, the phasing and the appropriate level of investment in the definition and procurement phases, prior to starting major capital commitments and construction.

Jan 1, 1999

By Junji Shibata

The waste acid mixture whose main component is phosphoric acid, is discharged from the etching process in the liquid crystal production industry. In order to separate impurity acids from the phosphoric acid, trioctyl phosphate (TOP) is used as an extractant. TOP can extract acetic and nitric acids selectivity. The extraction and stripping operations are carried out for the acid mixture by beaker-scale experiments and countercurrent multistage operations with mixer-settler equipment. TOP selectively extracts the acetic and nitric acids in the acid mixture. From the results of the McCabe-Thiele analysis obtained by beaker-scale tests, the extraction for acetic and nitric acids are approximately 100%, respectively, by 6-stage extraction with a phase ratio (A/O) of 0.4. On the other hand, almost all of acetic and nitric acids are stripped with water from the organic phase by 4-stage stripping with a phase ratio (A/O) of 1.0. About 95% of acetic and 98% of nitric acids can be removed from the acid mixture without extracting phosphoric acid in case of the mixer-settler equipment operation. There are several steps such as slicing, lapping, chemical etching and mechanical polishing in the silicon wafer production process. The chemical etching step is necessary to remove any damaged layer caused in the slicing and lapping steps. The typical etching liquor is the acid mixture comprising nitric acid, acetic acid and hydrofluoric acid. The waste acid is treated by a neutralization method with a high alkali cost and balky solid residue. A solvent extraction method is applicable to separate and recover each acid. Acetic acid is first separated from the waste liquor using 2-ethlyhexyl alcohols as an extractant. Then, nitric acid is recovered using TBP (Tri-butyl phosphate). Finally hydrofluoric acid is separated with TBP solvent extraction. The expected recovered acids in this process are 2mol/L acetic acid, 6mol/L nitric acid and 6mol/L hydrofluoric acid. The yields of this process are almost 100% for acetic acid and nitric acid. On the other hand, it is important to recover and reuse the metal values contained in various industrial wastes from a viewpoint of environmental preservation. Most industrial products are made through processes to separate impurities in raw materials, solid and liquid wastes being necessarily discharged as industrial wastes. Chemical methods such as solvent extraction, ion exchange and membrane separation, and physical methods such as heavy media separation, magnetic separation and electrostatic separation are considered as the methods for separation and recovery of the metal values from the wastes. Some examples of the application of solvent extraction to the treatment of wastes such as Ni-Co alloy scrap, Sm-Co alloy scrap, fly ash and flue dust, and liquid wastes such as plating solution, the rinse solution, etching solution and pickling solution are introduced.

Jan 1, 2003

By Ladislav Bebar, Tomas Parizek, Radek Dvorak, Petr Stehlik

"More and more sweeping environmental regulations initiate research, development and introducing into operation up to date technologies for cleaning off-gas and flue gas generated in various branches of industry and municipal waste treatment. The following systems based on novel types of equipment are shown: thermal and catalytic treatment of waste gases polluted by VOC (Volatile organic compounds) and carbon monoxide (alternatively NOx), catalytic filtration for efficient destruction of PCDD/F (dioxins) and potentially NOx, wet cleaning of flue gases polluted by SO2, HCl and HF with a original type of homogenizer “O-element”, integrated equipment for cleaning waste gases polluted by solid particulates, SO2, HCl, HF and heavy metals (alternatively NOx or PCDD/F). The outstanding features of all equipment mentioned above are low investment and operating costs together with high removing efficiency of pollutants. These units can be used mainly in incineration plants, refineries and other chemical plants. The paper represents a review based on papers published in reputable international journals and a monograph under preparation as well as on experience from industrial applications.IntroductionIn the recent years, more and more emphasis is put on preserving clean environment. One of the most closely monitored objects of general public attention are exhaust gases, containing a number of undesirable compounds like NOx, CO, SO2, HCl, HF, fly ash a PCDD/F. These harmful species are created in chemical processes mainly in the industry, transport and energy sectors. There is therefore a strong impetus for abatement of these harmful pollutants. Sectors of industry are thus subject to emission regulations specific to various types of units. In the framework of increasing demand for a clean environment, the concerned legislation is becoming increasingly strict and requires removal of pollutants by modern methods that would ensure efficient abatement of emissions at reasonable investment and operating costs.Attention is focused chiefly on methods for decreasing harmful emissions from thermal waste treatment facilities processing industrial and municipal waste that may be subsequently applied in other sectors of industry. Units for the thermal treatment of waste not only provide means of its disposal, but may become also important sources of energy, provided that strict emissions limits are satisfied. Figure 1 compares emission limits given by the legislation for municipal waste incinerators and limits for a selection of energy sources with heat capacity up to 50 MW (see EU regulation 200/76/EC). The Figure implies that the values of emission limits for waste incineration are mostly comparable with emissions from the combustion of natural gas. Thanks to the continuing improvements of the methods for removal of harmful pollutants, the emissions from waste incinerators are typically deep below the limits."

Jan 1, 2008

By M. D. Strachan

Technical & Procurement Services Limited (TECHPRO) in Ashford, Kent, UK, have been appointed as Project Managers for the major rehabilitation of the Copper Smelting complex of Nkana Division, Zambia Consolidated Copper Mines Limited, (ZCCM) Zambia. In outline, the overall scope covers three main areas: a) Transfer and implementation of new technology into Zambia for the production of primary copper. b) Replacement of gas collection and gas treatment circuits to guarantee high quality feed to the acid plants. c) Completion of a number of minor projects in the copper smelter and associated utility plants to complement changes in the primary smelting technique. This paper describes the Project Management methodology and style used by TECHPRO to tackle typical problems that arise in retrofit projects of this type. Reference is made specific aspects of the smelter projects to illustrate solutions to the problems. The subjects. addressed highlight the complexities not only of having a -Client 5,000 miles from the Project Office, but also the difficulty of co-ordinating and controlling the performance of min sub-contractors who are also geographically distant.

Jan 1, 1991

By Jong Hyeon Lee, Go-Gi Lee, Chang-Kyu Lee, Hong Youl Ryu, Sung-Koo Jo

This study deals with research on the reduction process of neodymium oxide by molten salt electrowinning. Neodymium fluoride and lithium fluoride electrolyte were used for feed stock of electrolyte and neodymium oxide was added as precursor. Cell current was confirmed that cell potential was applied as constant potential of 4.5V. Argon gas injection into the electrolyte was carried out to confirm convection effect on current efficiency. Applied current was gradually decreased without argon flow, but applied current was kept within a certain range with argon flow in electrolyte.

Jan 1, 2015

By A. V. Tarasov, V. M. Paretsky

"The design is based on the thermal processing of the wastes in· the intensively bubbled melt in the Vanyukov furnace at the relatively high temperatures (1350- 1450 °C), In this case: -the secondary wastes are not formed; - the especially toxic substances at the outlet from the furnace are absent. The technology was tested on a large scale (on semicommersial bases). Technical and economical basis show profitability of recovery complex for processing of hard garbage waste (HGW) using this technology: the period of capital, investments refunding for the, recovery, complex construction with process annual capacity of 240 thousands tons of wastes is 1,5-2,5 years,"

Jan 1, 2000