Search Documents

By T. Shimizu

In Japan, the emission standard of selenium in effluent was set at a maximum of20 mgll in Feb. '94 for the first time, and it is scheduled to be further decreased to a maximum of 0.1 mg/I from Feb. '97 due to tightening of the Water Pollution Prevention Act. Selenium (IV) and (VI) are generally found in effluent from precious metals refineries. Although selenium (IV) can be easily eliminated by some reducing agents, selenium (VI) is more difficult to be reduced. Therefore, many smelters are having difficulty in complying with the new emission standard. At Mitsubishi Materials' Naoshima smelter, the behavior and the elimination of selenium in effluent have been extensively investigated. As a result, it was found that two strategies were particularly effective. One of them is improving the overall operation of precious metals refinery, that is, feeding uniformly the effluent to the waste-water treatment plant, reducing the effluent volume by recycling and recovering more selenium (IV) in the effluent. The other is eliminating selenium (VI) in the effluent from the precious metals refinery. It was found that selenium (VI) can be effectively reduced by using hydrazine under high? sulphuric acid concentration and high temperature conditions. By using these measures, it is considered that Naoshima Smelter will be able to comply with the new emission standard.

Jan 1, 1996

By Peng Bing

Stainless steelmaking dust is classified as a hazardous waste due to higher than acceptable heavy metal leachabilities such as zinc, lead, cadmium and chromium. In addition to being an environmental hazard, the flue dust is also an economical concern to stainless steelmakers as it contains large amounts of valuable alloying elements, especially for iron, chromium and nickel. A new technology of direct recycling of stainless steelmaking dust has been developed to recover the metals from the dust. But it was found that zinc was accumulated in the dust collection system in practical run of direct recycling. This study focuses on the effect of the operating parameters such as temperature, dust feed rate and the ratio of CO to dust on the reduction of zinc oxides present in the dust. The mathematical model for the reduction process was setup based on the experimental research. According to the mathematical model, the temperature has obvious effect on the reduction of zinc. It is benefit to the process of zinc reduction to increase the temperature. But the temperature will not be the main factor for the reduction process after 1228C. It will promote zinc reduction to decrease the dust feed rate and control the ratio of dust to CO. It was also found from the experiments that ZnFe2O4 in the dust could be decomposed at high temperature. Decomposing ZnFe2O4 in the dust increases the recovery of zinc from the dust distinctly.

Jan 1, 2006

By W. G. Davenport

Chapters 19 and 20 examine direcHo-copper flash smelting and flash converting. This chapter compares the two processes and suggests which is likely to be 'the more economic for a given concentrate. It: (a) uses Chapter 19's direct-to-copper industrial oxygen and oil requirements (b) adds the energy required for electric furnace recovery of Cu from direct-to-copper slag (Czemecki et al 1999) (c) combines Chapter 20's, flash converting calculations with Chapter 18's flash smelting calculations to determine their combined industrial oxygen and hydrocarbon fuel requirements (d) adds the energy required to granulate, crush and dry flash smelting matte for the flash converter (e) adds the energy required to granulate and dry flash converter slag for recycle to flash smelting (f) compares direct-to-copper and flash smelting/flash converting in terms of their total equivalent hydrocarbon ener.gy requirements.

Jan 1, 2001

By Kandipati Sreenivasarao

A promising method for removing heavy metal ions from dilute effluents is ion- or precipitate- flotation, in which a suitable collector is added to form hydrophobic metal-collector complexes or compounds that can be collected as foams. We have successfully removed Cu(II), Cd(II), and Pb(ll) from dilute solutions using sodium dodecylsulfate and ethanol as collector and frother respectively. However the process would not be economically viable unless the collector could be recycled, and the heavy metals recovered in a concentrated, preferably marketable, form from the foams. We investigated four different methods to decompose heavy metal-dodecylsulfate complexes, namely precipitation of hydroxides, precipitation of sulfides, chemical stripping, and electrolysis. We compare the performance of these methods. In each case the observed behavior is related to known thermodynamic data, and potential applications are discussed.

Jan 1, 1995

By A. Valenzuela

During the last years, Chile has been the largest copper producer, either as concentrates or cathodes. Copper obtained via pyrometallurgy is produced by seven smelters, which have carried out modernization plans to increase smelting capacity or to achieve environmental regulations established in the Chilean legislation. Thus, the present work updates technological innovations in smelters, environmental regulations and presents solutions for S02 handling, particulate matter and arsenic. Also, the authors emphasize the important role of CODELCO Chile, the most important state-owned copper company, in developing technologies such as El Teniente Converter and El Teniente Slag Cleaning Furnace.

Jan 1, 2003

By Wenying Liu

The effect of aeration on chalcocite heap leaching was studied by analyzing the historical data from two chalcocite heap leach pads located in Chile, one with aeration and the other without aeration. The data showed that the copper leaching kinetics of the aerated heap was greater than that of the unaerated heap within a certain leaching period, after which there was no effect of aeration on the copper leaching kinetics. The total acid consumption per ton of ore processed was higher in the case of aeration, which was supported by the higher pH of the PLS. But the net acid consumption per ton of copper produced was the same in the two cases. Approximately 5% of the total iron added to the unaerated heap was precipitated inside the heap. In contrast, there was no net iron precipitation or generation inside the aerated heap. Bacteria activities were thought to occur even in the unaerated heap, but the extent was much less than in the aerated heap. Given the importance of forced aeration in chalcocite heap bioleaching, mathematical modelling will be applied in the future work to assist the optimization of the aeration system design.

By Sumantra Mandal

The hot deformed microstructure of the 15Cr-15Ni-2.2Mo-Ti modified austenitic stainless steel (commonly known as alloy D9) was investigated employing electron backscatter diffraction (EBSD). Hot compression tests were conducted in a Gleeble thermo-mechanical simulator at temperatures of 1173K-1373K (in steps of 100K) with a strain rate of 10 and 100 s-1 to different strains. Various kinds of deformation patterns were observed inside the deformed grains. These were inferred as the development of geometrically necessary boundaries or formation of parallel set of micro-bands. Recrystallized grains were partitioned from the deformed grains employing grain orientation spread approach. Extent of dynamic recrystallization (DRX) was found to be minimal at 1173K. DRX was predominantly found to happen at and above 1273K which increases with increase in strain. DRX nucleation and development mechanisms were discussed with respect to bulging of the parent grains and sub-grain rotation. Special emphasize is given on the role of annealing twins on DRX nucleation and subsequent expansion.

Jan 1, 2009

By Jack S. McPartland

Historically, research on thiosulfate leaching of precious metals ores has been focused on processing of difficult to treat ores. Thiosulfate leaching of ores and concentrates containing sulfide minerals, copper, manganese and preg-robbing carbon constituents has been evaluated. Cyanide leaching is generally considered an efficient, environmentally acceptable means for processing of non-refractory precious metal ores, Consequently, commercial processing of finely disseminated, oxidized precious metal ores is normally accomplished using alkaline cyanide leaching. Recent changes in regulatory climate have, however, called into question the acceptability of cyanide leaching in a number of locations worldwide. In some cases where the use of cyanide is being questioned, thiosulfate leaching may provide an acceptable alternative. Developments in thiosulfate leaching of precious metal ores are reviewed in this paper.

Jan 1, 1999

By Jan G. H. du Preez, C. Viviers, B. J. A. M. van Brecht, H. E. Rohwer, Nicole M. Sumter

"At the basis of metal ion separation lies some particularly metal ion specific chemical property which lends itself towards exploitation. This could be in the form of an anionic complex or a neutral chelate complex. In the former a cationic centre with a particularly high affinity for the complex will have to be designed. In the latter case a stereospecific chelate ligand containing the correct symmetry and type of donor atoms will have to be designed. In both above cases the ""active centre"" can be entered in a from that it can function in different media of hydrophobicity, eg a precipitant, a resin or a solvent extractant. Recent results obtained in this laboratory will be used to illustrate how the above variables can be exploited to develop improved processes for the separation of base metal and platinum group metals.IntroductionThe separation of metal ions in hydrometallurgy can be performed broadly speaking with two major aims. Firstly the separation/removal of a certain group of metal ions, either as a means of preconcentration or as a removal from effluent as part of a purification process and, secondly the removal of a specific metal ion from an industrial stream in order to produce a specific metal in a pure form. This latter operation is by far the most difficult of the two and is becoming more so in the light of the fact that the world is moving in the direction of lower grade ores and increasing pollution. Such a process can be divided into three essential parts, firstly the molecular one in which an active centre is required to obtain specificity, secondly a matrix within which this active centre must function, i.e. as part of a resin or solvent extractant and thirdly the design of the total system to optimize the realization of the operation."

Jan 1, 1996

By Munyaradzi Kwatara, Ron Schonewille, Edgar Peek, Juzer Tayabally

"The potential recovery of nickel from a South-American saprolitic laterite ore using the segregation roasting technique was investigated. The ore was heated to temperatures that ranged between 900 and 1 000°C in a rotary kiln. In all the tests, the laterite ore was first mixed with a predetermined amount of calcium chloride and either coal or coke. By varying the temperature, calcium chloride and reductant in the different tests, a preliminary set of optimal conditions was established for the specific laterite ore that was tested. A combination of chemical analysis and electron-probe-micro-analysis (EPMA) were used to determine and evaluate the effectiveness of segregation roasting on the recovery of nickel. The present paper describes the test procedure and the results that were obtained.IntroductionIt is known that laterite ore resources account for an estimated 72% of the world's nickel resources, with sulfide sources accounting for the remaining 28%. Yet sulfide resources account for 58% of the world's primary nickel production while laterite resources account for the remaining 42% [I]. There are numerous reasons for this discrepancy, but the most important one is the mineralogical and compositional complexity that is associated with laterite ore deposits. For example, this complexity currently offers only limited opportunities for upgrading, thereby creating capital intensive whole ore processing facilities. It then follows logically that the identification and application of a low-cost processing option for the treatment of laterites could potentially open up an opportunity for exploiting these vast untapped laterite resources.To this end, a preliminary screening investigation was initiated by Xstrata Process Support to evaluate the potential application of the so-called (nickel) segregation process as a unit operation that could potentially be integrated into a laterite processing flow sheet. Laboratory bench tests were performed on this segregation process and this paper details some of the findings from this preliminary investigation."

Jan 1, 2011

By D. R. Spink

A partial desulfurization roasting (PDR) technique has been developed for use on zinc concentrates whereby the sulfide sulfur associated with the iron content is selectively removed over a very short residence ?time in the roaster. The resulting PDR product is then leached for the selective removal of the iron. The resulting leach restdite is an upgraded zinc sulfide concentrate which has a very low iron content. The up-graded zinc concentrate can be subjected to a conventional dead roast without formation of deleterious zinc ferrite so that hot acid leaching and jarosite (or other) iron precipitation steps are obviated. Examples are presented for the treatment of three very different types of zinc concentrates.

Jan 1, 1990

By Igor Rojkovic

The most important uranium mineralization in the Western Carpathians occurs in the Permian rocks. Low grade stratiform uranium mineralization was formed during the Permian due to adsorbtion and reduction by organic matter, titanium oxides, iron hydroxides, pyrite and clay minerals. During the Alpine orogeny uranium (± molybdenum and copper) remobilized stratabound ores were formed. Dominant ore minerals are uraninite, U-Ti oxides, molybdenite, pyrite and chalcopyrite Two generations of ore minerals are reflected by their textures and chemical composition.

Jan 1, 1995

By B. Q. Li, S. P. Song

"This paper describes an on-going research on developing coupled boundary element and finite element algorithms for the solution of thermal and electrodynamic problems relating to materials processing. The coupled methods are uniquely suitable for field problems involving composite regions, in which detailed information on field distributions within one particular region is of more interest and yet the solution can be obtained only if the effects of other regions are all considered. Problems of this type include heat transfer in multiple regions and also magnetic induction involving an infinite boundary. The hybrid boundary and finite element formulation, algorithm development and the applications are discussed. Two examples are given to demonstrate the capability and accuracy of the coupled algorithm for heat transfer problems. Various treatments of corner discontinuity are discussed. It is found that the double flux treatment is an ideal choice amongst those tested as it is easy to implement and also gives the most accurate solution. 1. INTRODUCTIONElectrodynamic and transport problems occur frequently in materials processing systems. Accurate solution of these problems is of great importance not only for our fundamental understanding of physical principles governing these phenomena in the processing systems but also for optimization of the existing processes as well as development of new processes. For this purpose, many numerical algorithms have been developed. These computational schemes in general can be classified into three categories, that is, the finite element and finite difference schemes and the boundary element scheme. The former two are domain based numerical algorithms while the latter the boundary-based algorithm.The finite element method, which is based on the variational calculus, is a very useful and yet popular engineering numerical method for boundary value problems defined over irregular boundaries. The use of the method requires the discretization of the entire domain. It can be applied to solve both linear and nonlinear problems, but is particularly powerful for nonlinear problems that involve the field variables defined within the computational domain. On the other hand, the boundary element method, with its root in the Green's function method, is very efficient for linear boundary value problems or nonlinear problems that involve field variables only along the boundaries. The primary advantage of the boundary element method lies in the fact that only the boundaries of the computational domain need to be discretized, and hence the dimension of the problem is reduced by one, compared with the finite element method."

Jan 1, 1994

By William E. Frazier

The presence of minute amounts of sulfur (10ppm) in nickel-base superalloys has been associated with reduced oxidation resistance and the premature spallation of protective coatings. Removal of sulfur by annealing these alloys in a hydrogen atmosphere has been successfully attempted by several researchers. This paper examines the fundamental thermodynamics and kinetics governing hydrogen desulfurization of elemental nickel. Limiting conditions for successful desulfurization are delineated. Assuming that the diffusion of sulfur is the rate limiting process of desulfurization, the effectiveness as well as time associated with hydrogen desulfurization is explored.

Jan 1, 1994

By Markus A. Reuter

In this paper, the kinetics of phosphorous production in submerged-arc furnaces will be discussed as a function of temperature, as well as various ore and reductant types. Interesting positive synergetic effects on the rate of reaction could be observed when mixing different types of ores. The results will be discussed with reference to a kinetic model, microprobe analyses, etc. The effects these results have on the control of the furnace will also be discussed in detail, indicating how these could be incorporated into the electrode and metallurgical control systems for submerged arc-furnaces.

Jan 1, 2000

By Jian Li, J. Miles, P. Liu, W. Cook, W. Zheng, Alvin Qian

"High temperature corrosion resistance is one of the key challenges in water-cooled nuclear reactor material development. Iron based materials with low Cr content exhibits superior high temperature mechanical properties. However, due to the relatively low Cr content, their corrosion resistances under supercritical water (SCW) conditions are generally poor. High-Cr alloys, despite their much improved corrosion resistance, often suffer from embitterment due to the precipitation of sigma phase in the microstructure. In this study, corrosion resistance of an in-house produced high Cr steel (25%Cr) showed much better corrosion resistance compared to that of low Cr alloy (14%Cr). This high-Cr steel can potentially be used as a corrosion-resistant coating for structural materials in sew applications.INTRODUCTIONThe supercritical water-cooled reactor (SCWR) concept is one of the promising designs for the next generation nuclear reactor, in which the water coolant is designed to be at about 625°C and 25 MPa at the outlet of the reactor core. Under these relatively high-temperature and high-pressure conditions, the cooling water is at supercritical state. High-temperature mechanical properties, corrosion resistance and radiation damage are some of the key challenges. At present, no single commercial material can meet all the requirements of the severe SCWR in-core conditions. Canada supports research in several key areas of SCWR development, including materials selection. A major focus is on materials development, selection and evaluation for both in-core and out-of-core components.Allen et. al. [1] carried out a comprehensive study on the SCW corrosion resistance up to 600 °C on commercially available high temperature materials including Ni-based super alloys, various types of stainless steels and ferritic/matensitic steels. They concluded that ferritic steels develop a relatively thick but mechanically stable oxide layer, while austenitic alloys develop a thinner oxide layer that has been found to spall in some cases. Of the three types of alloys examined, the Ni-based alloys exhibited the lowest oxide thickness, however pitting was observed in the vicinity of intermetallic precipitates."

Jan 1, 2011

By Ron Bernard

HW Process Technologies has successfully developed and commercialized various applications utilizing Engineered Membrane Separation (EMS?) systems for the processing of acidic copper hydrometallurgical solutions and wastewaters. Copper hydrometallurgical EMS? applications include water balance control and increased copper concentration in heap and dump copper leach operations, tankhouse bleed stream treatment to separate/recover copper and cobalt from iron, and removal of PLS/Electrolyte suspended solids/colloids to eliminate "crud" formation during copper SX/EW. Similar applications are underdevelopment to provide ionic separations in copper refinery bleed streams, copper smelter acid plant streams, as well as organic/LIX removal from aqueous electrolyte and raffinate streams. Copper mine wastewater EMS? applications include treatment of copper leach solution contaminated groundwaters for copper recovery and treatment of unwanted heap/dump drainage to provide enhanced precipitation, a smaller precipitation plant, improved operating costs and better quality discharge water, particularly in terms of TDS and sulfates. A discussion of the EMS? technology and general separation results on typical process solutions and wastewaters will be presented. HW Process Technologies, Inc. commercial installations treating copper pregnant solutions and leach solution contaminated groundwaters are in-place at an old Asarco smelter/refining operation, Mexicana de Cananea copper mine, and a major U.S. copper mine, with several additional installations pending. Several case studies, including results from a selection of these installations, will be included with detailed capital, operating cost, and system payback data.

Jan 1, 1999

By P. Thapliyal

The petroleum refining industry generates over a million tons of spent catalyst per year, containing valuable metals. Currently, these materials are recycled to smelting furnaces, but the fundamental mechanisms controlling the recovery processes are poorly understood. Furthermore, submerged injection of finely divided materials is potentially a means to obtain high recoveries of pay metals. In this study, a catalyst containing 10% Ni and 1% Co was injected into 45 kg heats of matte. A copper matte was chosen so that the nickel and cobalt recoveries were measurable. It was found that the recovery ranged from 40 to 700Al, increasing with catalyst feed rate, decreasing with catalyst particle size and decreasing with the oxygen content of the carrier gas. A mathematical model was developed to account for the results, and to permit extrapolation to nickel mattes. The industrial implications are discussed.

Jan 1, 1996

By W. L. Cornell

Bulk sulfide concentrate produced from Missouri Pb ore concentrator tailings must be reground to liberate sulfide values for subsequent sepa-ration. Studies to determine grinding parameters for optimum liberation were carried out using optical microscopy coupled with image analysis. The major sulfide phases present in the ground mineral particulates are marca-site, pyrite, sphalerite, galena, chalcopyrite, siegenite. and bravoite. Results showed that the base metal minerals were liberated by grinding to 74 micrometers (200 mesh), but the siegenite and bravoite required grinding to 20 micrometers or less to achieve liberation. Both the experimental method and results are presented.

Jan 1, 1987

By Yunhua Gan, Xiaowen Chen, Yang Tong

Experimental studies of electro-spraying were carried out using ethanol as fuel in a microcombustor under combined electric field. And the effects of different electro-spraying modes on the combustion efficiency were analyzed. Results showed that when ring electrode potential was invariant, there were four different electro-spraying modes with the variations of nozzle potentials, which were varying with the flow of ethanol. The cone-jet mode was the stablest one during the whole experimental process. The atomized ethanol was ignited and combusted stably near the steel mesh, the combustion efficiency increased firstly and then decreased along with the increasing of the equivalent ratios, reached the maximum values when the equivalent ratio equal to 1.0. And the maximum values were the highest at the cone-jet mode, and the lowest at the pulsed-jet mode.

Jan 1, 2016