Search Documents

By Ramiro Escudero

Michoacan?s beach sands with interesting concentrations of ilmenite were studied to produce titanium by hydrometallurgical techniques. Nevertheless, among titanium species, there are different additional components of Michoacan?s beach sands which could be of interesting applications. Some of them are likely to be applied for the manufacture of nanocrystalline ceramics. Although, the most applied mineral dressing to treat these kind of sands, that contain magnetic species (i.e., ilmenite, magnetite), is a combination of gravity separation and magnetic separation, it could be of a great deal of benefit to apply the information regarding the surface characteristics of the sands? components, in order to study the application of flotation technologies to separate selectively those species with commercial value.

Jan 1, 2006

By Hideyuki Itou

Municipal wastes are mainly incinerated in Japan. Both bottom ash and fly ash from the incineration treatment are smelted recently to decrease the volume. Direct smelting of municipal wastes is also becoming popular. The smelting treatment generates fly ash which contains concentrated heavy metals such as Zn, Pb and Cu, and the harmfulness is causing concern. The smelter fly ash is mainly landfilled after stabilization. An effective treatment process of the smelter fly ash is required to recover the metals. For the treatment process, an application of chloridizing volatilization technique is considered. Chloridizing volatilization experiments were carried out to determine the effects of various factors on the volatilization behaviors in this study. A pretreated ash was mixed with a main raw material which mainly consists of hematite. Calcium chloride water solution was added into the mixture. The mixture was pelletized, dried and used as samples for the volatilization experiments. The sample was placed in the reaction tube heated in an electric resistance furnace. 5%02-95%N2 gas with controlled humidity was introduced into the reaction tube. Effects of humidity in the carrier gas, addition of calcium chloride and mixed ratio of the ash to the main raw material were investigated on the volatilization of Zn, Cu and Pb. To determine the volatilization behavior, samples were taken from the furnace at specified temperatures on the heating stage. In addition, experiments at specified holding temperatures for 15 minutes with shortened heating time were conducted. The two series of experiments revealed the effect of heating temperature on the volatilization behavior of Zn, Cu, Pb and Cl.

Jan 1, 2006

By G. W. Barton

Process Systems Engineering (PSE) can be defined as the integrated usage of computer-based design and analysis tools. As such, PSE is becoming increasingly important in the chemical and petrochemical industries. This paper shows how a range of PSE techniques have been applied to the zinc electrowinning process. Topics discussed include model development, parameter estimation, steady-state and dynamic model applications, steady-state optimisation and neural network modelling.

Jan 1, 1994

By Cesar O. Gomez

A procedure has been developed for mounting at random particles of mineral samples to be characterized using image analysis. The procedure is based on the generation of a random distribution of sample particles in particles of a diluent material. and the embedding of this particle mixture in an epoxy resin without disturbing the initial distribution. Two materials with atomic number similar to that of the epoxy resin were successfully used as diluents: activated charcoal and graphite. The proportion of diluent material to be mixed with the sample to have a large number of mineral particles in the field of view while keeping the occurrence of touching particles at an acceptable level was determined empirically. The randomization achieved with the procedure developed in this work was tested using as samples known mixtures of silica and pyrite particles of the same sieve class. The agreement obtained between the mass ratio of minerals used in the preparation of a particular specimen and that resulting from image analysis demonstrates that the procedure developed is successful in producing a specimen where the embedded particles are randomly distributed.

Jan 1, 1988

By Ross Baldock, Ross Andrews, Gu Helin, Lan Xu, Markus Reuter, Song Xingcheng

"A commercial lead smelter using Outotec Ausmelt TSL Technology has been successfully commissioned and put into operation at Yunnan Tin Company Ltd operations near Gejiu City, in Yunnan Province, China. The plant was commissioned in July 2010 after three years in the design and construction phase. The process uses a three stage batch process to produce lead bullion and zinc fume, and a slag that is low in metal values. The paper provides details of this lead smelting project, including the theoretical evaluation of the multi-stage process chemistry, engineering design, plant commissioning and the final operation. Comparison of the design targets and actual performance of the plant is emphasized. The fast ramp-up to full production of the largest Ausmelt TSL lead furnace built to date is highlighted.IntroductionIn 2002, Ausmelt and Yunnan Tin Company (YTC) successfully commissioned a smelter to modernise the Yunnan Tin smelter in Gejiu City, Yunnan Province, China. A single Ausmelt furnace was installed by YTC to process tin concentrate and revert materials, to produce YT Brand tin product. The advanced Ausmelt Technology furnace at YTC replaced seven existing reverberatory furnaces and provided a flexible, energy efficient and environmentally beneficial system to complement the world leading refinery facilities of YTC."

Jan 1, 2012

By Rafael Padilla

The recovery of copper from chalcopyrite concentrates by leaching is difficult due to the slow dissolution kinetics of this mineral in most leaching media. However, recovery of copper from sulfidized chalcopyrite (a mixture of CuS and FeS2) by leaching is faster and could be selective depending on the leaching media. In this paper, the result of an investigation on the H2SO4-O2 pressure leaching of sulfidized chalcopyrite is presented. The variables considered in the study were stirring speed, concentration of sulfuric acid, temperature, and partial pressure of oxygen. The experimental data indicated that stirring speed over 500 rpm and sulfuric acid concentration over 0.1 M had very little effect on the leaching rate. An increase in temperature from 90 to 100 ºC increased both copper and iron dissolution; however, further increase to 120 ºC affected negatively the copper dissolution. Oxygen partial pressure was found to be the main variable that controls the copper/iron selectivity of the leaching. An increase in oxygen partial pressure increased significantly the rate of copper dissolution but deteriorated the copper/iron selectivity. The analysis for sulfur of the leaching solid residues indicated that most of the copper sulfide sulfur in the sulfidized concentrate oxidized to elemental sulfur.

Jan 1, 2006

By Jörg Buchmayer, Menno Eisenga, Erik Muijsenberg

"In the past decade, advanced multiple input/multiple output (MIMO) process control systems have found their way into high temperature melting processes. Today a growing number of high temperature melters have been equipped with a supervisory control system. Daily regulation of fossil fuel firing and electric energy supply to stabilize temperatures is no longer in the hands of the operator, but fully taken over automatically by the ES III™ MPC controller, which provides consistent process control, 24 hours per day, focused to operate the entire glass production process in the most efficient way. The presentation will show practical results and benefits achieved in the high temperature glass and cement industry.IntroductionThe Expert System, either version ESII™ or ESIII™, provides supervisory multi-variable model based predictive control in time and space This definition is not very understandable to people who are not familiar with advanced process control, thus let's try to explain it word by word.The word supervisory means that the Expert System implementation preserves the primary control level: all devices (PLCs, internal switches) as well as up to date control mechanisms (PID loops, availability to change inputs manually). ES III™ can even use primary control level elements as part of the advanced process control.The next word, multi-variable, means that multiple inputs can be handled at the same time to affect multiple outputs. This property is very important for supervisory control of the glass melting and conditioning processes. For example, in a float furnace the total amount of gas is only one of the inputs that affect the crown temperatures. The next one is batch feed rate. And batch composition (the next one) is maybe even more important. An ambient temperature also correlates with crown temperatures. So it can be concluded that crown temperatures are affected not only by one variable ""total gas"", but by many more. On the other hand, there are usually several crown temperatures with different importance for process control. And we have not discussed yet the effects of glass level, canal temperatures, oxy-boosting, etc. All of them affect (or are affected by) process control too. Overall, the process control is a complex problem where multiple inputs and outputs play strongly together at various levels of importance."

Jan 1, 2012

By R. W. Smith

A microorganism will function as a mineral flocculant if it is to some degree hydrophobic and can attach itself in some manner, such as through electrostatic interaction, to the fine mineral particles to be flocculated. The present paper concerns the use of a hydrophobic bacterium, Mycobacterium phlei, as flocculating agent for phosphate slimes. Experimental work on the flocculation of phosphate slimes and of dolomite and clay mineral suspensions was performed. It was found that M. phlei functions as an excellent flocculant for a dolomitic slime but does not function as well for mineral suspensions where large quantities of the solids are finer in size than the approximately 1 µm size of the bacterium.

Jan 1, 1992

By Garry W. Warren

The brass foundry industry produces a significant amount of waste sand containing Cu, Zn and Pb which is often classified as a hazardous waste due to Pb content. The potential application of a hydrometallurgical process to treat the sand by extracting metal values and thus detoxifying the material has been investigated. The process involves leaching of metal values followed by cementation. The emphasis of this investigation was on the leaching step, although some preliminary cementation experiments have been performed. In order for any alternative treatment scheme to be successful, the smaller size fractions of the sand must be addressed. Experiments have been performed on five individual size fractions using various lixiviants HCI, acetic acid and HCI/NaCI. Cu extraction was found to be slower than either Zn or Pb. Results obtained in this investigation indicate that copper is present in two forms, an oxide form which dissolves rapidly and is insensitive to the level of oxygen, and a less soluble form, probably metallic which dissolves more slowly and requires an oxidizing agent. The presence or absence of oxygen had no influence on the rate of Zn dissolution indicating that zinc is present mostly in oxide form. Toxicity Characteristic Leaching Procedure (TCLP) tests showed that residues could be produced which meet the toxicity limit for lead. Preliminary cementation experiments have also demonstrated the feasibility of Cu and Pb recovery.

Jan 1, 1991

Gas flow and heat transfer phenomena in two industrial-scale waste-heat boilers of the Outokumpu copper flash smelting process were analyzed with a commercial computational fluid-dynamics (CFD) package Phoenics. Various operating conditions were simulated for the first boiler and particularly for the second boiler. The gas flow pattern was compared qualitatively with the physical laboratory models, and the general flow pattern was consistent with the laboratory visualization. The heat transfer simulation was validated with, temperature measurements for both boilers, and good agreement was reached between the computed temperature profiles and the measured data. The computational results indicate that gas flow in both boilers is of three-dimensional and recirculating nature. The numerical tracer experiments indicate that some dead volume is present in both boilers, and the boiler modification reduced the dead volume from 38% to 15% under basic operating conditions. Radiative heat transfer accounts for 65-90% of the total 'heat transported in the radiation sections of both boilers under different operating conditions. The modified boiler is very efficient for cooling the off-gases at almost doubled volume flow rate. The CFD modeling proved to be a useful tool for numerical experiments and analysis of boiler performance for process: optimization.

Jan 1, 1998

By Yuan Lu, Yiming Rong, Richard D. Sisson Jr

With the development of quench technology, there is a trend of using gas quench to replace liquid quench for less distortion and residual stress. The fundamental difference between the liquid and gas quench is the heat transfer coefficient, not only the values but also the shape of the curve as a function of temperature. The equivalent heat transfer coefficient for the liquid and gas quench is analyzed by simulations and experiments. Even it may result in the same hardness in the liquid and gas quench, the steel microstructure may be different because of the different cooling processes, and therefore other steel properties, such as toughness, may be different. The cooling process, microstructures and properties such as hardness and toughness should be examined when designing the liquid or gas quench processes.

Jan 1, 2015

By Gary K. Elliott

Many industrial processes generate hot waste gases which contain particulate pollutants. Conventional clean-up techniques suffer limitations either because collection efficiency is low or because the gas must be cooled before treatment. thereby increasing costs and preventing energy recovery. The application of increasingly stringent environmental legislation to the non-ferrous metallurgical industry is presently illustrating these conventional technology limitations. Low density ceramic media allow filtration to ta,ke place at 'high temperatures and are now rapidly becoming accepted In many industries. This paper reviews experiences with a proprietary low density ceramic filter element. CerafH. It includes consideration of the structure, composition. typical operating and case studies with particular reference to non-ferrous metallurgical furnace applications.

Jan 1, 1992

By Gary K. Elliott

Many industrial processes generate hot waste gases which contain particulate pollutants. Conventional clean-up techniques suffer limitations either because collection efficiency is low or because the gas must be cooled before treatment. thereby increasing costs and preventing energy recovery. The application of increasingly stringent environmental legislation to the non- ferrous metallurgical industry Is presently illustrating these conventional technology limitations. Low density ceramic media allow filtration to take place at high temperatures and are now rapidly becoming accepted in many industries. This paper reviews experiences with a proprietary low density ceramic filter element, Cerafill. It includes consideration of the structure, composition. typical operating and case studies with particular reference to non-ferrous metallurgical furnace applications.

Jan 1, 1992

By R. C. Hubli

Copper (II) chloride has proven to be an efficient lixiviant for copper sulphide ores and secondary sources of copper such as scrap. Nickel sulphides are generally associated with copper ores and copper-nickel matte is an intermediate product of processing mixed sulphides. While the copper species in aqueous chloride media are present as chlorocomplexes, the presence of nickel as Ni++ offers effective separation between the two by solvent extraction techniques. Oxidation of millerite by cupric chloride in sodium chloride solutions has been studied as a function of rate of agitation, leaching time, temperature, acid concentration and total initial cupric concentration. The reaction has a 1/2 order of dependence on initial cupric concentration in the range of 0.0 to 0.5M. The activation energy for the temperature range 333 -363 K has been found to be 59.2 kJ/mol with chemical reaction at the unreacted mineral surface as the rate controlling step. The rate expression, according to the shrinking-core model, for initial cupric concentrations between 0.0 to O.5M, is evaluated as

Jan 1, 1996

By Hideya Sato

Refractory wear caused by melts is one of the major determining factors for the interval of shut-down repair of the metallurgical furnaces in general. Calcium ferrite slag employed by M it subishi Continuous Copper Converter, shows hi& fluidity and corrosive characteristics against most of the refractories. In order to improve the corrosion resistance of the refractories, the mechanism of MgO-based refractory wear by the calcium ferrite slag was intensively studied. The dissolution behavior of the refractory into the molten slag and the penetration of the molten slag into the refractory were observed by crucible tests and newly developed oscillating furnace tests. It was found that the wear of MgO-based refractories by the calcium ferrite slag is mainly dominated by the internal structural failure caused by the penetration of CaO-Cu20 rich slag which is formed as a result of the preferential absorption of FeO, from original slag by the spinel of the refractory.

Jan 1, 1999

By R. A. Alock

The character, occurrence and genesis of the three types of nickel deposits, sulfide, laterite and deep-sea nodule are described, highlighting the differences in mineralogy and chemical composition that effect the extractive metallurgy of nickel and associated byproducts. World nickel production and current resources by deposit type and geographic location are also reviewed.

Jan 1, 1988

By H. K. Lin

Pyrite oxidation in chloride solutions was investigated with cyclic voltammetry, ac impedance and potential step techniques. The pyrite oxidation in quiescent electrolytes is irreversible and controlled by diffusion. Depression of the semi-circle in the complex plane plot has been explained mathematically based on the concept of the equivalent circuit. When the semi-circle is depressed, the mathematical formula indicates that the reaction resistance should be obtained from the intersection of the semi-circle with Z-axis instead of the semi- circle diameter. The peak charging current densities at 1.10 and 0.90 V vs. SHE obtained from the equivalent circuit coupled with the ac impedance measurements match the peak current densities obtained with the potential step measurements.

Jan 1, 1997

By Miller, Geoffrey W.

The Ravensthorpe Nickel Project (RNP) flow sheet provides for the upgrading of Ni & Co in a size based beneficiation process prior to leaching. The upgrading effect on Ni and Co makes the beneticiation process a powerful addition to the flow sheet. Multiple linear regression (MLR) analysis based on 351 individual batch tests, 52 large scale composites and 21 pilot plant tests has been used to successfully model beneticiation product grade, recovery, upgrade and mass recovery. Statistically, 83% and 96% of the variability in nickel recovery and nickel product grade respectively was accounted for. Algorithms have been developed for Ni, Co, Mg, Al and Fe, which represents the revenue and operating cost factors for the process. The algorithms have subsequently been applied to the resource model, allowing prediction of elemental grade and recovery for the development of the mine schedules based upon these parameters and not head grades alone. This has allowed optimisation of the mine schedule for improvement to the project's NPV. Keywords: Ni Laterite, Prediction, Multiple Linear Regression, Beneficiation

Jan 1, 2004

By Manuel Alvarado, David Nemir, Jan Beck

"Thermoelectric generation using special N-doped and P-doped semiconductors is well known as a means for direct heat energy to electrical energy conversion without the need for moving parts. The technology is used today in niche markets for low level electricity production and has been proposed as a scalable means for capturing large scale energy from waste heat streams. The choice of geometry of the thermoelements and conductors is critical to the successful implementation of a waste heat recovery system in order to manage losses due to Joule heating and diffusive heat flows. This paper describes a simulation study to define the performance impact of different aspect ratios for the active thermoelements and the electrical interconnect. The use of a finite element model that incorporates the intercoupled heat and electrical energy flows highlights some of the issues impacting scalability.IntroductionThermoelectric phenomena arise out of the intercoupled electrical and thermal currents in a material. A two-element thermoelectric generator is depicted in Figure 1. It is constructed by connecting an N-type thermoelement and a P-type thermoelement in electrical series, with both elements in thermal parallel between a heat source and a heat sink. The electrical series connection is made by attaching conductors as shown. Ideally, these series connection elements will be both good thermal conductors and good electrical conductors.The two element generator in Figure 1 is disposed between two thermal reservoirs: the heat source, which furnishes heat energy; and the heat sink, which absorbs heat energy. Heat energy flux Q, flows from the heat source to the heat sink, driven by the temperature difference between the source and the sink. As depicted in Figure 1, when a resistive load, R, is attached, electrical current, I, may be extracted from the thermoelectric generator and furnished to the load. The N-type and P-type thermoelements, are the active portions that do the actual conversion of heat energy to electrical energy. Although thermoelements may be built using conductors such as bismuth and antimony, higher efficiency thermoelectrics are built using heavily doped semiconductors. Thermoelectric devices are generally formed by connecting many pairs (couples) of N and P type thermoelements in electrical series and in thermal parallel. A commercially available module having 127 couples (254 elements) is shown in Figure 2."

Jan 1, 2011

By Tatsuzo Kitamura

The tank house of Tamano refinery, that started its operation in January, 1972, was constructed incorporating the application of Periodic Reverse Current (P.R.C.) from the outset of design works. In 1973, the production of electrolytic copper came up to 8,000 mtpm, a sharp increase ds compared with the designed capacity of 7,000 mtpm, and successful operation has been achieved up to the present. P.R.C. has been employed for the purpose of raising productivity level and reducing copper inventories. Since there were various problems in P.R.C. application to such a large sized cathode as 1 m x 1 m, special attentions were paid to the following items: -Development of a unique bus bar to make an electrolytic current to each electrode as uniform as possible. -Improvement of circulating method of electrolyte. -Application of high-performance equipment to realize a uniform spacing between anode and cathode. Owing to these creative technical developments mentioned above, technical level for operation up to 350 amp per sq m of cathode current density has been established. The quality of electrolytic copper, which was a matter of interest, has been proved to be as excellent as those of conventional electrolysis products through a long term supply to the field of SCR and Dip forming where high levels in quality are required.

Jan 1, 1976