Search Documents

By L. Munsamy

The bulk of primary mining at the Anglo Coal's Bank Colliery was carried out by drill and blast method, in a bord and pillar layout exploiting the No. 2 Seam. Secondary extraction, top/bottom coaling, also took place using both the drill and blast (D&B) method and continuous miners (CM). Extensive mining in this seam resulted in the risk of sterilising the No. 4 Seam reserves. Therefore, multiseam design guidelines established by Salamon and Oravecz (8) were re-evaluated in light of the low safety factors and the low pillar width to mining height ratios of pillars in the No. 2 Seam. Two and three dimensional (2D & 3D) numerical modelling was carried out to quantify and verify the parameters that influence the multiseam mining. The modelling was conducted primarily in two dimensions (plane strain), with 3D models to confirm the validity of the 2D results. A panel risk assessment flow chart was developed to assess the panels with respect to pillar failure and multiseam mining. This flow chart was extended into the evaluation of risk of surface subsidence using the current rock engineering knowledge. The aim of this risk assessment tool is to assess all underground workings at Anglo Coal collieries simply and rapidly. The identification of high-risk areas would warrant further investigation and possible backfilling to reduce the risk of pillar failures ensuring that reserves in the No. 4 and 5 Seams above are intact.

Jan 1, 2004

By Ryan Garvey

A numerical investigation is made into unstable failures of coal pillars (i.e. coal bumps) using the finite difference software FLAC3D. A static energy balance is first derived to calculate the excess energy released as a consequence of unstable failure in rock. Two- and three-dimensional mining layouts are then assessed on their bump-potential based on the magnitudes of excess energy released during simulated pillar failures. A three dimensional pillar model is developed to represent tributary area loading of an infinite room-and-pillar layout. Pillar strength and brittleness characteristics are calibrated using a Mohr-Coulomb strain-softening constitutive law to simulate width-to-height ratio coal pillars ranging from 1:1 to 5:1. Width-to-height ratio pillars 1:1 to 3:1 release large magnitudes of excess energy as the pillars fail, representing massive collapse of room-and-pillar layouts. The larger pillars maintain their residual strength during failure; however significant excess energy is still released during temporary reductions in pillar strength. A two-dimensional model is then constructed of a gate road pillar failing due to elastic rebound of the surrounding rock mass. Soft loading conditions initiate unstable failure for all pillar widths, while the total magnitudes of excess energy increase with the size of pillar being modeled. The results from these tests indicate that excess energy may be used as a direct assessment of the bump potential of simulated mine layouts.

Jan 1, 2013

By Thomas R. Scotese

A rock mechanics instrumentation and monitoring program was implemented during pillar extraction at Gulf Mineral Resources' Mt. Taylor Mine, the deepest uranium mine in the U.S. Three types of monitoring were employed: (1) drift convergence around stopes (using a portable tube extensometer), (2) stress changes in pillars (using vibrating wire stressmeters in horizontal boreholes), and (3) load changes in haulage ways under stopes (using vibrating wire load cells in jack stands). Results include convergence-time graphs, convergence contour maps, stress-time graphs, a stress increase contour map, load-time graphs, and abutment load limit maps. Major factors influencing results include (1) size of pillars around the extraction area, and (2) presence and orientation of a major fault adjacent to one extraction area. These factors, combined with pillar extraction, produced evidence of load transfer over 120 m from a stope measuring only 55 m x 45 m. Vertical stress increases of 7 to 17 MPa (1000 to 2500 psi) within 60 m of the stope were obtained using the stress- meter manufacturer's method. The fault apparently prevented load transfer in the down-dip direction but increased load transfer in the up-dip direction. Convergence rates of up to 1.3 cm/day (0.5 in/day) were measured at two stations. Instruments were generally reliable despite adverse underground conditions. The instrumentation and monitoring program at Mt. Taylor provided a warning system against ground control problems and a characterization of ground behavior for future development and extraction of pillars. Recommendations are made for future mining and instrumentation practices.

Jan 1, 1984

By Al Campoli

The majority of the 100 million roof bolts installed each year in the United States are 5/8 inch deformed rebar fully grouted into a one inch borehole. Commonly referred to as B-Series or No. 5 bar, this system is proven effective and cost efficient in coal mines with average to above average roof conditions. One of the critical variables affecting resin bolt performance is the size of the resin annulus, calculated as the difference between the hole and bolt diameters. The optimum annulus has been proven to be '/4 inch, which provides for effective mixing of the two polyester resin components and incorporation of the plastic film packaging within the cured resin. Glove fingering occurs when the plastic film is forced against the borehole wall potentially interfering with the mechanical interlock of the resin and the rock mass. Glove fingering is not a problem with the optimum '/n inch annulus but has been know to occur with the B-Series 3/8 inch annulus. Laboratory testing correlated the degree of Glove fingering with resin formulation and the bolt head to shaft axes alignment. Glove fingering occurred over 45 % of the grouted length of standard B¬Series bolts. The newly formulated Eclipse B-Series resin when combined with a 1/8 inch offset between the bolt head and shaft axes reduced the glove fingering 70%. The Eclipse system allows the 3/8 inch B-Series annulus to achieve the positive mixing characteristics associated with the / inch optimal annulus systems.

Jan 1, 2002

By Anthony T. Iannacchione

Underground bituminous coal mining is a large and significant industry within the Commonwealth of Pennsylvania, and it has a legacy of environmental consequence. For example, in 2008, 13.5 acres (5.5 hectares) of land were undermined by longwall mining every day. Laws and regulations have been promulgated requiring companies involved in this industry to remedy mining damage caused to homes, businesses, and land; replace impaired water supplies; and repair impacts to streams and wetlands. The regulations and technical standards set by the Pennsylvania Department of Environmental Protection (PA DEP) have been put in place to assure that coal operations comply with ACT 54 of the Bituminous Mine Subsidence & Land Conservation Act and other related legislation. These regulations and standards require operations to address impacts when a mining permit is submitted and as permits are modified and extended. One of the special provisions of ACT 54 is the requirement by the PA DEP to produce an assessment of the surface impacts of mining every five years. The University of Pittsburgh was contracted by the PA DEP to perform the 3rd assessment, which spanned from August 21, 2003, to August 20, 2008. This paper details the findings related to surface structure undermined during this period. A total of 3,735 structures were tracked. Four-hundred-fiftysix reported effects were found, and each required additional information and analysis. The majority of the reported effects were associated with eight longwall mines. Characteristics of the structures were analyzed and discussed, with special attention to those with reported effects. The number of undamaged and reportedly damaged structures (i.e., dwelling, barn, commercial building, etc.) undermined during the assessment period were listed. Lastly, the resolution status and type of resolution were analyzed for all structure reported effects.

Jan 1, 2011

By W. C. Smith

Over the past several years, the Bureau of Mines has conducted studies on the performance of fully grouted resin bolts In underground mines. The effectiveness of resin-grouted bolts in maintaining a competent roof, even in weak rock, has been well documented in the literature. Recent Bureau studies have evaluated the affects of shortened grout columns on bolt behavior in a variety of rock types (1, 2, 3). The application of partial grout columns to primary roof support systems has been introduced as a viable alternative to fully grouted bolt systems in some mines. The point-anchored resin bolt and combination bolt represent such alternatives. While both systems usually employ some mechanical interlocking system, their primary difference lies in the length of resin column used. Point- anchor systems rely on an anchoring device that is a short length of resin column of 2 feet or leas. Combination bolts, on the other hand, often require 3 feat or more of resin column. Resin migration into voids and fractures intersecting the borebole wall is a major problem when installing fully grouted bolts in weak roof rock and can result in a reduced column length that provides reduced anchorage. The relationship between column length and anchorage integrity deserves closer study. The Denver Research Center of the Bureau of Mines has examined the load- carrying capabilities of resin-grouted bolts in weak strata. Pull tests were performed on about 900 resin-grouted, 4- foot-long bolts with column lengths ranging from 6 to 48 inches. The practical performances of 8 different column lengths were evaluated for 10 mines under in sit" conditions using data obtained from standard pull tests. In addition criteria are discussed, including engineering properties of the host rock for designing safer and more effective grouted bolt installations.

Jan 1, 1987

By Yunqing Zhang

Roof failure occurs much more frequently at intersections than entries and crosscuts. Using a commercial finite element package, four-way and three-way intersections reinforced with the tensioned bolts are modeled. The 3-D model considers bolt pre-tension, bolt installation procedure, bedding planes and in-situ horizontal stresses. The modeling results from both four-way and three-way intersections are analyzed with regard to the intersection stability. The mechanisms of tensioned bolting at the intersections are investigated and some tensioned bolting guidelines for intersections are given. Based on this study, a better way to enhance intersection stability is to use longer bolts than entries or crosscuts and increase the bolt density near the intersection corners.

Jan 1, 2003

By Leo L. Van Sambeek

Specification of properly sized pillars to support the overburden is one of the most challenging aspects of salt mine design. Interest in salt pillar design is heightened by the recent flooding of the Retsof salt mine, water inflows to the K2 potash mine, and closing of the Belle Isle salt mine because of ground control problems. A series of numerical modeling analyses show that a simple pillar design equation for salt pillars adequately reproduces results of extensive modeling efforts. The paper describes (1) the basis for the pillar design equation, (2) equation verification by comparison with numerical modeling results, and (3) equation validation by comparison with measurements and observations of salt pillar behavior.

Jan 1, 1997

By Jimin Su, Enguang Zhu, Kangning Zhang, Yang Li

"The effect of interburden on overlying strata movement during the mining of a lower group coal seam is still a challenge in China. Based on the multiple coal seams in western China, numerical simulation and field tests are applied to study the interburden and overburden movement during the undermining process. This study focuses on the impact of the thickness and structure of the interburden, the proportion of hard rock, and the ratio of the overburden thickness to interburden thickness (OB/IB). In this paper, four typical underground coal mines are simulated for lower seam longwall mining with different interburden parameters. The results indicate that the ratio of the overburden thickness to the interburden thickness is not the dominant actor for multiple seam longwall mining, especially in the mines in western China,which feature shallow depth. The thick and hard interburden could strongly affect the lower coal seam mining process. INTRODUCTION The project background is based on four typical underground coal mines in western China.The information on the overburden and interburden is shown in Table 1. Different overburden to interburden thickness (OB/IB) (Ellenberger, 2009) values of the four coal mines are also studied: 6.2 in Bulianta coal mine, 7.2 in Kaida coal mine, 8.2 in Shigetai coal mine, and 9.4 in Halagou coal mine. The proportions of hard rock in the interburden of the four coal mines are also different: 0% in Kaida coal mine, 70% in Shigetai coal mine, 80% in Bulianta coal mine, and 100% in Halagou coal mine. To be specific: the thickness of interburden are listed as follows: 7m in Halagou coal mine, 6m in Kaida coal mine, 10m in Shigetai coal mine, 28m in Bulianta coal mine. The depth of the upper coal seam are: 66m in Halagou coal mine, 54m in Kaida coal mine, 79m in Shigetai coal mine, 182m in Bulianta coal mine. NUMERICAL SIMULATION UDEC 4.0 is applied in this paper to analyse the overlying strata movement and the interburden failure.(Liu, 2007) This is based on mining in the lower coal seam under the mined-out upper coal seam (Majdi, 2012, Morsy, 2006)."

Jan 1, 2017

By Liu Xiao, Lin Xiaoying, Ma Geng, Tao Yunqi

"The soft coal in China has several issues, low permeability, high gas content and prone to gas outburst, making it difficult to drill and improve its permeability. Using the rock mass loading test, the relationship of stress-strain-permeability-time of sandstone was investigated. The fracture network that communicates with coal seams to provide the pathways for gas migration can be established by drilling, hydraulic fracturing or loose blasting in the roof and floor about 5m from coal seams top and bottom. The gas migration can be summed up as ""desorption-diffusion-two levels of seepage"" for gas drainage of the quasi-protection-layer in hard coal seams, and ""desorption-two levels of diffusion-seepage"" in soft coal seams. In the quasi-protection-layer, different gas drainage techniques were used during different stages of mining. Gas drainage of the quasi-protection-layers was demonstrated at Hebi Zhongtai Mining Co., Ltd. The results showed that the technique promotes the gas seepage flow, and improves the efficiency of drainage. The influence zone of the quasi-protection-layer was 1601 m2 and the average amount of gas drainage was 328m3/d, with the maximum being 661m3/d. INTRODUCTIONGas is one of the main factors that cause disasters and influence safety production in underground coal mines (SACMS, 2009). The coal-bearing formations in China have been subjected to multiphase tectonic stress field during the period of geological evolution. Coal body was often crushed into fragmented coals and mylonitic coals under the tectonic stresses (Su and Lin, 2009). The gas permeability of coal is generally poor. So in underground, drilling and hydro-fracturing technology have been used to improve the permeability of coal, such as intensive drilling, hydraulic punching, hydraulic cutting, hydraulic extrusion and deep hole blasting. But the gas drainage rate was low, only 23% (Liu, Li, and Li, 2006; Li and Wei, 2006; Henan Polytechnic University, 2008; Ma, et al., 2014; Lin and Wu, 2009; Zhou, et al., 2011) that was much lower than the rates achieved in the main coal-producing countries such as America and Australia whose average rate of gas drainage was 50%. The protection layer mining technology has been used widely as an effective technique to improve the permeability of coal in the mining of multiple coal seams (Cheng and Yu, 2003; Diaz and Gonzalez, 2007; Karacan, et al., 2007; Palchik, 2003; Latham, et al., 2013; Yuan, et al., 2013; Shi and Liu, 2007; Wang, et al., 2008, Guo, et al., 2015; Lu, et al., 2015; Slazak, Obracaj, and Swolkien, 2014 ). In the single low permeability coal seam, there is no protection layer. This kind of coal seam has low permeability, high gas content, soft coal body, and is prone to serious gas outbursts. During drilling, the holes very often spray, collapse, stuck and wedged the drilling tool. The hole length drilled is difficult to reach the required minimum, the service life of holes for gas drainage is short, the construction cost is high, and the holes are difficult to maintain. The gas drainage efficiency of single low permeability coal seam, especially soft coal seams, cannot be improved even though hydro-fracture technology has been implemented, because its permeability is not improved."

Jan 1, 2016

3-D finite element modeling was performed to study the effect of bedding plane sliding and separation and tensioned bolt in layered root It was found that the major influence zones of a tensioned bolt are restricted to the neighborhood of the anchor points; that bedding plane sliding and separation releases the vertical stress in the roof above entry but greatly increases the horizontal stress within the first layer of the roof, and that there is a triangular zone between the two adjacent bolts at and near the roofline level that is beyond the influence zone of the bolts which is liable to fail if conditions exist. Based on the results, three possible modes of roof failure are proposed for the design of tensioned bolting.

Jan 1, 2001

By Zhijie Zhu

In order to determine the overburden failure characteristics of extra-thick seam mining, EH4 electromagnetic image system and borehole televiewer survey were applied to panel 8100, Tongxin coal mine. EH4 electromagnetic imaging system was used to map the overburden strata before and after mining. Analysis of the distribution of the electrical conductivity showed that the fractured zone height was 492-558 ft (150-170m); Observation through the borehole televiewer showed that the fractured zone height of water conductivity (or water flowing fractured zone height) was 110m-142m. The results of the two methods showed that the fractured zone height of water conductivity was 492-558 ft (150- 170m) or 10-11.3 times the mining height.

Jan 1, 2014

By James D. Pile

Following a methane ignition in the active panel of a longwall coal mine, the affected panel was successfully isolated from the rest of the mine. This allowed for the remainder of the mine to return to regular operation, and the conventional practice of having to seal the portals for a defined period of time was avoided. After the affected panel had remained isolated for a regulatorily mandated period of time, it was reopened in preparation for longwall face recovery. As it was not possible to move the shields from their existing positions to facilitate the installation of recovery mesh prior to shield recovery, alternative methods had to be considered to stabilise the gob and minimise flushing, thereby improving operator safety. The objective of the paper is to show how stabilisation of the gob was achieved during shield recovery, thereby minimising flushing, and improving operator safety. Phenolic foam was chosen and injected from between the shields into the gob behind them. This is a technique that has been used to great effect in Germany, to a lesser extent in Australia, but not knowingly to date in the United States. To ensure nothing was left to chance and thereby guarantee the project?s success, the procedure used in Germany was employed, down to the application of equivalent hardware, which was sourced through the North American supplier.

Jan 1, 2013

By Xicai Gao

With the intensification and expansion of deep coal mining, the surrounding rock stress environment becomes further deteriorated because of the complicated geological environment and powerful mining effect, so the major deformation of roadway appeared frequently. The proportions of floor heave are increasing and , the most serious problem is the floor heave of preparatory workings. The coal seam of Binchang coal area in Shaanxi province is at a depth of 621.6 ~ 817.0 m, the average thickness of the coal seam is 25 m, and the overburden and coal measure strata are the main regional aquifers and are highly permeable. The properties of water-weakening are obvious in the floor strata. The main preparatory workings or chambers were driven in the coal seam. The severe floor heave of the water chamber appeared during early mining and the amount was 180 ~ 910mm, and seriously affected the normal installation and use of the water chamber. Theoretical study and numerical simulation as well as the in-situ measurements were carried out to investigate the deformation and failure characteristic of the surrounding rock with non-support in the floor and the main reasons which caused the floor heave were determined. A new combined support technology was proposed which consists of overcutting, grouting, backfilling and invertedarch and bolt-grouting. The field monitoring showed that the cumulative convergence of the water chamber was 20mm, the maximum convergence speed is 1.2 ~ 2mm/d, the accumulative convergence of two ribs was 36mm and the maximum convergence speed is 2mm/d. The combined support technology will enhance the support intensity between the roof and floor, the two sides of the entry and improve the loading capacity of the floor effectively and the floor heave can be controlled effectively.

Jan 1, 2013

By Samrat Mohanty

The construction of underground hydrocarbon storage caverns in Jurong Island, Singapore, is nearing completion. The facility, located beneath the seabed of Banyan Basin, is comprised of five storage caverns with a storage capacity of approximately 1.5 million cubic meters. The galleries of each cavern are 20 m wide by 27 m high and approximately 340 m long. In addition to the storage caverns, various access and operations tunnels are required to support the facility. Among these are water curtain galleries to ensure that hydrostatic pressures in excess of hydrocarbon storage pressure are maintained in the rock mass surrounding the storage caverns. Early in the design process, conventional steel rock bolts with resin polymer grout were considered for ground control. However, the construction contractor proposed using fibe-reinforced polymer (FRP) bolts with cement grout due to the corrosive hydrologic environment, weight and handling considerations, local construction preferences, and the requirement to have a cavern design life of 50 years. FRP bolts with cement grout were ultimately chosen for the project. The FRP bolting system has proven to be very successful, with no ground failures experienced where systematic FRP bolting has been applied. This paper discusses the properties of FRP bolt/cement grout bolting systems, their characteristics in relation to steel bolt/resin bolting systems, and numerical modeling results assessing their performance.

Jan 1, 2014

By Jinwang Zhang, Zhaohui Wang, Jiachen Wang

"Thick coal seams (seam height larger than 3.5 m) account for a large portion of the proven coal reserves of China, and underground thick coal seam mining provides about 50% of the Chinese annual coal production. Such seams are mainly mined using the longwall top-coal caving (LTCC) method. For safe and successful mining, a number of analyses on the stability of surrounding rocks in the LTCC face area have been extensively performed, and certain research achievements have been made. This paper introduces the main findings on rock pressure occurrence in the LTCC face during the last few decades and presents face and roof stability control techniques. INTRODUCTIONUnderground thick coal seams in China provide 1.8 billion tons of coal every year, which accounts for approximately 50% of the total Chinese annual coal production and 25% of the world, indicating that thick coal seams stand an important position in Chinese coal mining industry (Wang, 2005). Before the 1980s, thick coal seams were mined mainly by using the multiple-slice mining method. With the improvement of mining techniques and equipment in last two decades, longwall top-coal caving (LTCC) and high-seam, single-cut longwall are employed for thick coal seam extraction, offering advantages over multiple slicing from entry excavation and production perspectives (Wang, 2013).. The primary author of this paper introduced the most popular thick coal seam mining methods in China at the 30th ICGCM (Wang, 2015). This paper presents the stability of surrounding rocks in face area and ground control techniques for mining thick coal seams. For traditional longwall faces (seam height less than 3.5 m), the well-developed VoussoirVoussoir beam theory has been successfully used to analyze the movement of overlaying strata, which indicates that ground control techniques have become mature for this mining system. In such faces, the four-leg support with loading capacity of 4000–8000 kN is considered adequate for safe and successful mining. These faces normally have an annual yield of 1–2 million tons (Wang, 2007). For thick coal seams, however, the traditional support becomes inadequate and the ground control problem change to be more difficult and complex. Thus, development of large-scale mining equipment and ground control techniques for enlarged mined-out space and entries have been recognized as the most basic technical problems in mining thick coal seams."

Jan 1, 2017

By Eric Keller, Jamal Rostami, Wenpeng Liu

"Roof and rib instability is an important issue in underground mining. To optimize ground support design, enhance ground stability, and reduce the possibility of roof or rib failure with minimal use of artificial ground support, it is essential to have an accurate understanding of ground conditions. This includes the location of voids, cracks, and discontinuities, as well as information about the different strata in the immediate roof. This paper briefly introduces ongoing research on void detection by using the roof bolter feed and rotation pressure. The goal of this project is to improve the sensitivity of detection programs to locate smaller joints and reduce the number of false alarms. This paper has presented a brief review of the testing procedures, data analysis, logic, and algorithms used for void detection. In addition, this paper has discussed the results of preliminary laboratory tests and statistical analysis of the data from these two drilling parameters used for void detection.INTRODUCTIONRoof falls are one of the most serious and frequent accidents in underground mining. Each year, personnel are injured or killed because of roof falls. Equipment can also be damaged when this occurs. According to Mine Safety and Health Administration statistics collected from 1999 to 2008, ground falls were the largest cause of fatal accidents in underground coal mining, causing around 40% of all fatalities (NIOSH, 2015a). Out of 8 to 10 fatalities and over 800 injuries are recorded each year in underground mines, there are nearly 2,000 reportable non-injury ground falls every year (NIOSH, 2015b).Certain features in the ground, such as voids, cracks, and discontinuities, are significant factors that cause roof support failures and roof fall accidents. Currently, several manufacturers provide smart roof bolters with limited capabilities for void detection. While successful in many instances, in laboratory experiments, the existing void detection systems have limited success in detecting void openings that are less than 1/8 inch This limited success was observed in testing concrete blocks with gaps in between, simulating a rock medium with voids. Detection programs have missed some voids, while, in some cases, they have shown false detection. These algorithms need to be more accurate in sensing voids to improve the capabilities of these programs."

Jan 1, 2016

By Andy L. Shaffer

A novel liquid settlement system (LSS) was installed in advance of mining at a western United States (U.S.) longwall mine to measure total roof sag from the time of cutting to days after mining during gate road development. The system was used to compare differences in roof sag between conventional place-change mining using a Joy continuous miner and a Fletcher roof bolter and mining using a miner-bolter. The LSS was installed with an intrinsically safe, miniature data acquisition system (MIDAS) to record roof response at four locations in the same gate road. The system utilized pressure transducers to measure roof sag by the principle of falling head (fluid pressure) in fluid-filletubes installed in the immediate roof. Details of the LSS design, installation, data collection, post-processing, and future applications are discussed.

Jan 1, 2014

By Andre Zingano, Anderson Weiss

"The objective of this paper is to study the behavior of a low thick and low depth coal seam and the overburden rock mass. The mining method is room and pillar in retreat and partial pillar recovery. The excavation method is conventional drill and blast because of the small production. The partial pillar recovery is about 30% of the previous pillar size, 7m x 7m. The roof displacement was monitored during retreat operation; the surface movement was also monitored. The effect of the blasting vibration on the final pillar strength had been considered. Due to blasting, the pillar reduced about 20%. The consequence is more pillar deformation and roof vertical displacement. The pillar retreat and ground movement were simulated in a three-dimensional numerical model. This model was created to predict the surface subsidence and compare to the subsidence measured. This study showed that the remaining pillar and low seam reduce the subsidence that was predicted with conventional methods.INTRODUCTIONMining low coal seams (less than 1 meter) with the room-and-pillar mining method implies the excavation of part of the roof or floor to maintain adequate entry height for equipment and compliance with labor regulations with respect to ergonomic issues. The direct consequence of this is an increase in coal contamination and the increased cost of transportation and preparation at the plant. Traditional room-and-pillar mining only uses a development operation, even with a continuous miner or drill-and-blasting. Therefore, all the run of mine (ROM) coal is carried out with part of the roof or floor. However, if the retreat mining method were to be considered, the quality of the coal could increase because only the coal seam is excavated from the pillar recovery. The quality of ROM coal will increase, and the cost will decrease proportionally to the amount of coal produced from the retreat operation.However, the retreat mining with partial or total pillar recovery implies greater subsidence. This is particularly true if the coal seam depth is shallow, under 100m depth. Subsidence prediction in room-and-pillar retreat mining is complex; it depends upon the remaining pillar (stump pillar) size, as well as the pillar height, and the behavior of the pillar after retreat. This is related to the strength of the remaining pillar, which is related to the excavated method (drill-and-blast or mechanical)."

Jan 1, 2018

By Elia Elias, Alan Crosky, Paul Hagan, Damon Vandermaat, Serkan Saydam, Peter H. Craig

"The University of New South Wales (UNSW Australia) had been involved in the study of premature failure of rock bolts in Australian coal mines from the initial identification of the problem in 1999 (Crosky et al 2002). Rock bolt steel changes over the last decade appear to have not reduced the incidence of failures. A broadened UNSW research project funded by the Australian Research Council (ARC) and Industry has targeted finding the environmental causes through extensive field and laboratory experiments. This paper describes the field studies conducted in underground coal mines, in particular attempts to measure the contribution to corrosion from groundwater, mineralogy and microbial activity. Various underground survey techniques were used to determine the extent of broken bolts, with the presence of both stress corrosion cracking (SCC) and localized deep pitting making no single technique suitable on their own. Groundwater found dripping from bolts across various coalfields in Australia were found to be not aggressive and known groundwater corrosivity classification systems did not correlate to where broken bolts were found. In-hole coupon bolts placed in roof strata containing claystone bands confirmed the clay as being a major contributor to corrosion. Microbes capable of contributing to steel corrosion were found to be present in groundwater, and culturing of the microbes taken from in-situ coupon bolts proved that the bacteria was present on the bolt surface. An ‘in-hole bolt corrosion coupon’ development by the project may have multiple benefits of 1) helping quantify newly developed corrosivity classification systems, 2) providing an in-situ ground support corrosion monitoring tool, and 3) for testing possible corrosion protection solutions.introductionThe problem of premature rock bolt failure in Australian coal mines was published in 2002 and 2004 by UNSW Australia from Australian Coal Association Research Program (ACARP) funded projects. The majority of the broken bolts examined had steel Charpy impact toughness values of 4 – 7 Joules, and the failure mechanism was most often stress corrosion cracking (SCC). Steel fracture mechanics predicts that an increase in impact toughness will increase the length of the crack before sudden brittle failure. In the final report of 2004, anecdotal evidence from one coal mine indicated that the problem may be eliminated in some environments by a change to steel grades with higher Charpy impact values of ~16. (Crosky et al, 2002 and 2004)"

Jan 1, 2015