Search Documents

By Yongjie Yang

Experimental study on the strength and deformation characteristics of coal under cyclic loading provides guidance for designing coal pillar which is subjected to repeated mining influence during mining. This paper studies the strength, deformation and fatigue process of No.3 coal from Xinhe Colliery under cyclic loading by the MTS815.03 servo-controlled rock mechanics test system. The results indicate that coal is more susceptible to fatigue damage than other hard rocks. Under uniaxial cyclic loading, the fatigue failure ?threshold value? of coal is smaller than 78% of its uniaxial strength, and there is also some fatigue damage when cyclic loading and unloading experiment is carried out below the fatigue failure ?threshold value?. Axial deformation can be divided into three stages: Initial deformation, steady-state deformation and accelerating deformation. Transverse deformation can be divided into two stages: Stable deformation and accelerating deformation. When the transverse deformation begins to increase rapidly and the deformation recovers only slightly upon unloading, it?s a precursor to failure of coal. Under cyclic loading, fatigue failure develops through a process of compaction, strain hardening, and strain softening.

Jan 1, 2006

By Daniel W. H. Su

Current longwall pillar design relies heavily upon past experience and many assumptions about pillar and entry response to longwall abutment pressures. Caving characteristics of the immediate and main roof strata are known to play an important role in the overall pressure redistribution, which determines the maximum abutment pressure, abutment pressure at the T-junction, and the width of influence zone. This paper presents the results of an extensive geomechanical study in a longwall panel at a West Virginia coal mine. The response of eight headgate pillars and the adjacent entries was monitored as the longwall face approached and passed by the instrumented locations. Overburden response to longwall mining was also monitored, and height of the highly fractured zone above the gob was determined by postmining drilling. Good agreement was observed between the measured stress changes and those computed using the known height of the highly fractured zone. The results provide a detailed picture of the response of overburden strata and chain pillars to longwall mining.

Jan 1, 1987

By Rusty Mchenry, Craig Dickerson, Robin L. Oldham

"It has been proven that longwall faces can be moved safely and efficiently. However, abutment pressures and poor ground control conditions can halt operations and be hazardous to coal miners. Recently at a mine in Southwestern Pennsylvania, roof material collapsed above shields that created two large voids and caused major challenges for shield recovery. A unique, engineering solution was developed that utilized a modified concrete material to fill the voids, creating stability in the affected area. The many phases of this project included the construction phase, void pumping, cutting out, and bolting of the concrete material. This project eliminated the hazards associated with bolting the recovery face and removing shields in adverse conditions, making it possible for the mine operator to safely complete the longwall move.INTRODUCTIONFrequently in the mining process, especially during the recovery phase, voids above the longwall supports have occurred. These voids are simply roof cavities caused by falling rock strata above the longwall face. Most often, this condition slows down or halts mining operations and creates hazardous work conditions for coal miners. Numerous methods of supporting void areas on longwall faces have been attempted and utilized throughout the mining industry since the advent of the longwall mining system. These methods have utilized many different materials and processes and have included the installation of steel or wooden beams, crib blocks, and various types of roof bolts. However, these methods can be dangerous due to exposure of personnel to the mine voids, falling roof material, and the necessity to handle large amounts of heavy support materials.This paper describes a unique case study in Southwestern Pennsylvania where longwall recovery methods, through two void fills, were successfully completed, eliminating exposure of coal miners to the rock voids above. At the start of this endeavor, normal recovery operations were halted, and hazardous conditions became a concern when the voids were encountered. However, in the interest of safety, the decision was made to try a unique method to completely fill the void from the bottom of the coal seam to the top of the void with a cementitious material and then mine through it. This is in contrast to traditional methods where beams and support materials are used to stabilize the area above and in front of the mine shields, which can expose miners to the void above."

Jan 1, 2015

By Michael Kelly

Longwall mining is the principal method of underground coal mining in Australia, with 70 million tonnes being produced by longwall mines in 1999. However, the mechanisms that control longwall geomechanics are still not clearly understood resulting in stoppages costing several hundred million dollars per annum The CSIRO has been investigating longwall geomechanics with consultant groups and minesites through several ACARP supported projects since 1994. The research has aimed to improve longwall support design and control methods by defining strata failure mechanisms and their occurrence about underground extraction panels, It also aimed to develop better predictive tools bur a broad range of underground environments. As a result of site studies at more than 8 locations some of the aspects that have been touted to control longwall geomechanics, especially from a 3D aspect are highlighted. These aspects include stress controls, geometry, faulting, depth. longwall width and changes in lithology.

Jan 1, 2000

By Y. Luo

This paper presents a number of mathematical models for predicting the different phases of the complete surface subsidence process associated with underground longwall mining. A computer program developed based on the mathematical models is briefly introduced.

Jan 1, 1992

By Kot F. Unrug

Since the introduction of longwall systems, the prediction of roof behavior and support requirements have become the major issue referring directly to safety as well as productivity. In more recent times, and especially in the USA where longwalls are exclusively equipped with costly hydraulic self- propelled support systems, a decision whether a longwall is applicable in a given condition, and when so, what kind of equipment should be selected, is of primary importance. There are numerous examples where lack of experience, and subsequently wrong selection of supports or winning machines, resulted in considerable losses. It should be emphasized that careful studies of prevailing geological and mining conditions, especially in a new area, are required to assure a successful operation. An evaluation of the conditions can be carried out in different ways utilizing such methods as: - Theoretical approach. applicable when geological conditions comply with the theoretical assumptions. - Empirical relationship which gives satisfactory results where the coefficients could be adequately determined. - Structural geological studies which must be undertaken in all cases, since the frequency of fractures and their orientation have a prevailing influence on roof behavior. - Scale model study on equivalent material for determination of failure conditions in the roof and mechanism of movement (flow) of broken rock matter. Coefficients for empirical formulas can be determined by these types of studies, as can boundary limits for mathematical modeling. - Mathematical modeling, e.g., finite element analysis. - Measurements and observations taken underground during the development period end utilization of experience for previous longwall panels in the area. Usually it is the most practical method where mining and geological conditions are comparable. An application of me or more of the above approaches remains to be a matter of judgement for particular conditions, however, the utilization of a practical experience, when available, is usually the safest way for planning a successful longwall operation.

Jan 1, 1982

By Bowler Jonathan, Lorraine Kent, Tereza Crisu, Stuart Walker, Nicholas Lightfoot

"It has been the practice in Europe to extract the most economic seams first: taking the seams sequentially, top down, to avoid operating within the fractured strata formed by the subsidence trough above previously mined coal seams. In the 1990s, the UK coal industry found itself at a number of sites having to operate over one or more previously mined seams. This led to specific geotechnical challenges with respect to maintaining economic, safe and stable rectangular roadways with rock-bolted support.Within this paper, the current challenges and mitigation strategies of overmining in the UK are described following the completion of a -three-year European Commission-funded project in 2015. The challenges and mitigation strategies are related to:• A case study with overmining of older workings of variable geometry;• Numerical modeling for overmining layout and support design; and• A case study site planning mine layout when considering future overmining.INTRODUCTIONAt the first case study site, case histories were examined for a mine operating at a depth of approximately 700 meters where five longwall panels were extracted above workings 35-40 m below. The overmining of various extraction geometries below led to challenging conditions in areas of high vertical stress concentration. It was found that results from one longwall panel could be suitably used to predict behaviour in a subsequent panel. The experience was used to update previously existing guidelines on the positioning of roadways in relation to subsidence troughs. Existing guidelines recommended that only as a last resort should longwalls be planned to retreat over narrow pillars, or from solid ground into a subsidence trough. Existing guidelines regarding the layout of overmining panels are conservative, and new work indicates that such multi-seam geometries are possible with appropriate support management strategies."

Jan 1, 2016

By Stephen C. Tadolini, Minova USA Inc., Peter S. Mills, David R. Burkhard

"Fiber-reinforced spayed concrete has been used for several years in civil and tunneling operations. Research conducted to reduce cure times and increase compressive and flexural strengths resulted in the development of Tekcrete Fast®, a cementitious product capable of obtaining 41 MPa (6,000 psi) compressive strength and 8 MPa (1,200 psi) flexural strength in only 3 hours and reaching 7 day strengths of 62 MPa and 11.7 MPa (9,000 and 1,700 psi), respectively. A single bag product that uses conventional shotcrete and gunite application systems make it a natural crossover product for mining applications. The discovery of incredible adhesion properties and high resistance to chloride permeability helps ensure long-term stability and increases the ease of application. Project results from Disaster City® in Texas and the application for rehabilitating a coal mine belt entry are presented. The case study illustrates the effectiveness of the product in stabilizing a coal mine beltway and adjacent cross-cuts that were subjected to progressive sloughage due to humidity and cyclical loading. INTRODUCTION Original research produced a shotcrete formulation that extends beyond stabilization and can be used to restore the structural integrity of damaged infrastructure. The primary challenge was to develop a shotcrete or gunite that had structural strength within a few minutes to prevent parasitic loading, allowing ingress into damaged structures minutes after applying the mix formulation. This also applies to mining conditions where rapid support of progressive failures can minimize failure. An additional benefit was discovering that the product had extremely high adhesion properties in addition to high flexural strengths. The approach to product design was the development of “single bag” dry mixes that are entirely self-contained, can be rapidly transported anywhere in the field or underground, and can be deployed using simple equipment. Dry mix eliminates issues relevant to high shear water mixing because water is added in the form of a mist at the point of delivery; thus a low water-to-cement ratio can be achieved. However, since there is no onsite powder mixing, the product must have a high degree of inherent homogeneity. Minova offers a commercial version of this material, Tekcrete Fast®, a product that has been successfully deployed in the mining industry and is currently being used in civil, construction, and tunneling operations. The material can rapidly stabilize lose ground in metal, nonmetal, and coal mines. This paper described the technology development, product testing results, and applications and describes a case study to stabilize a coal mine beltway."

Jan 1, 2017

By Simon H. Prassetyo

Violent failures of coal pillars, known in practice as coal mine bumps, have long been a subject of investigation. Many field investigations have considered geological conditions that create high stress in the pillar to be the main causative factor leading to bumps. In recent years, constraint at interfaces has been observed to be associated with the occurrence of coal bursts. This paper shows how interface friction and width-to-height (W/H) ratio affect the degree of violence of coal specimen failure. A series of UCS tests on 178 coal samples from bump-prone (Utah, called UT coal) and non-bump-prone (West Virginia, called WV coal) mines were conducted. Three violent failure parameters? peak sound pressure level, core zone failure, and ultimate stress? were used to assess the violence of failure. The degree of violence were investigated at varying interface frictions (high: µ = 0.40, medium: µ = 0.22, and low: µ = 0.13) and W/H ratios (W/H = 2, 3, 4, 5, 6, 7, 8, 10, and 12). A simulation series of modeled coal specimen under uniaxial loading was also conducted using the finite element method to observe the equivalent plastic strain distribution experienced by the modeled coal specimens. It was found that the violence of coal specimen failure depends on W/H ratio and interface friction. Interface friction has more significant influence on the violence of failure at high W/H ratios than it does at low W/H ratios.

Jan 1, 2011

By Keith Heasley

This paper is a retrospective on the development, application, and enhancement of the LaModel program from a personal perspective. The narrative starts with an explanation of the objectives behind the original development of the program and then introduces some of the unique and very practical features of the program. Next, a demonstration of how LaModel was advantageously used to model stresses and displacements in a multiple-seam mining situation with highly variable topography is presented. This is followed by the details of a number of the major enhancements and expansions of the program over the years. A back-analysis of the Crandall Canyon Mine collapse is then briefly presented, along with the associated development of a recommended calibration procedure for the critical input parameters to LaModel. Finally, some of the present research areas are briefly described, and future enhancements are introduced.

Jan 1, 2011

By Brent A. Slaker, Michael Murphy, John Ellenberger, Erik Westman

"Photogrammetry, as a tool for monitoring underground mine deformation, is an alternative to traditional point measurement devices, and may be capable of accurate measurements in situations where technologies such as laser scanning are unsuited, undesired or cost-prohibitive. An underground limestone mine in Ohio is used as a test case for monitoring of structurally unstable pillars. Seven pillars were photographed during four visits over a 63- day period. Using photogrammetry, point clouds of the mine geometry were obtained and triangulated surfaces were generated to determine volumes of change over time. Pillar spalling in the range of 0.29–4.03 m3 of rock on individual rib faces was detected. Isolated incidents of rock expansion prior to failure, and the isolated failure of a weak shale band, were also observed. Much of the pillars remained unchanged during the monitoring period, which is indicative of proper alignment in the triangulated surfaces. The photographs of some ribs were of either too poor quality or had insufficient overlap, and were not included. However, photogrammetry was successfully applied to multiple ribs in quantifying the pillar geometry change over time.IntroductionAdequately measuring underground rock mass movements is integral to understanding how rock masses behave and how to interact with them safely and efficiently. Many modern measurement techniques employed in underground mining environments rely on point measurements, such as through extensometers or borehole relief methods (Christiansson, 2006). These techniques, while commonplace, do not provide a comprehensive view of how the rock mass is behaving. The dynamic changes in stress states underground, coupled with the mechanical uncertainty of rock masses, near active excavations, creates a need for measurement systems which better capture the behavior of the rock mass. Photogrammetry is a technology capable of producing the wide-area displacement measurements required for a comprehensive understanding of rock mass movements.Digital photogrammetry is a means of obtaining threedimensional point clouds from digital photographs. By finding the same point across multiple images, all viewing an object from different angles, the location of that point in three-dimensional space can be inferred. Close range digital photogrammetry (CRDP) is photogrammetry applied to measuring objects or scenes less than 100 meters away (Atkinson, 1996), and is used for various functions in underground mining environments. These uses include, but are not limited to, mapping fracture networks (Kim, Kim, & Won, 2005)(Somervuori & Lamberg, 2010), characterizing fractures (Styles et al., 2010) and measuring volumes of blast rock (Heal, Hudyma, & Potvin, 2004)."

Jan 1, 2015

By Kazem Orace, Navid Hosseini, Mehran Gholinejad

"Selection of the optimum support system for underground openings such as tunnels is a complex process. In this paper a new approach, based on a combination of the Analytical Hierarchy Process (AHP) the Technique for Order Preference by Similarity to Ideal Solution (TOPSIS) and the Preference Ranking Organization METHod for Enrichment Evaluations (PROMETHEE), is introduced. For this purpose, the selection process is assumed to be a multi criteria decision-making problem. First different support systems using FLAC3D numerical code, based on technical safety and stability parameters of the tunnel are specified. Then taking economic and performance parameters as the decision criteria by using the combination of Al-IP, TOPSIS, and PROMETHEE the optimum support system is selected. As a real mine case study this approach is used in the main access entry to the C, coal scam of Tabas collieries. Results clearly demonstrate that the proposed support system selection method is more advantageous than other alternatives.INTROD CTIONGenerally, the support system for a tunnel is selected primarily with the aid of design engineers experience. In other words personal judgment instead of intellectual and scientific criteria is mostly the main basis (Oracc. 2005). However since various support systems can be applied in any particular situation, accurate selection of the optimum support method depends on the integration of many technical, economical and performance parameters, and also on the analysis of the intensity of influence by each of the criteria.In this paper an applicable approach for se lection of tunnel support systems based on Multi Attribute Decision Making (MADM) techniques including: Al IP (Orace et al.. 2009a; Saaty, 1980), TOPSIS (Hwang and Yoon, 1981: Yoon and Hwang, 1995), and PROMETHEE (Brans and Vincke. 1985; Brans and Mareschal. 1992) is introduced. As a field study, this approach was applied to tunnel C1 as one of the main entries in the Tabas coal mine which is the major collieries in the central pan of Iran (Hosseini, 2008).Due to the coal seam conditions coal is mined by mechanized longwall mining (Hosseini 2008). This method requires the 58 excavation of several entries some of which will be used for many years and even for the entire life of the mine (Peng, 2006). Therefore the selection of the support system in these entries is·very important in mining design."

Jan 1, 2010

By Zbigniew Lubosik, Stanislaw Prusek

"The main elements of hard coal extraction systems in the Polish mining industry, including the characteristics of gateroads, are described, followed by several dozen underground measurements of gateroad roof sag performed in different geological and mining conditions in Upper Silesia Coal Basin.Based on the analysis of the roof sag measurements, an attempt to describe the gateroad roof sag process using a geometrical model was made. To build the model, it was assumed that the roof sag curve could be described by three straight lines. The first line describes the roof sag ahead of the longwall face; the second line, the sag at the longwall-gateroad junction zone; and the last line describes the zone behind the longwall face. Determining the intersection points and inclination angles is essential for the model. These model parameters depend on the geological and mining conditions in the gateroad.Using the statistical computations and analysis, the dependencies between the characteristic points of the gateroad roof sag model and the selected geological and mining parameters were defined. The STATISTICA computer program by StatSoft was used for computation.This paper presents a simple form of the geometrical description of roadway roof sag progression that is very useful during the gateroad support design process.INTRODUCTIONThe longwall system with caving is the dominant method in European mining in cases of hard coal seam extraction. For instance, in Poland, in 2009, 117 longwalls were driven, with total production of 77.5 million tonnes. In roughly 95% of the longwalls, mining operations were conducted using longwalls with roof caving; the remaining 5% used the hydraulic stowing system. The average mining depth was about 700 m (2,297 ft), and average daily output per face was approximately 2,600 tonnes per day. When using the longwall mining system, gateroads play an important role. These principal roadways transport materials, mine crews, and output. In addition, they impact ventilation of the extraction area, affecting, among other things, the climatic conditions or methane hazard. Unfortunately, difficulties often appear in maintaining an adequate size for the gateroads, due to the face line, which causes origination zones with stress concentration around the gateroad, resulting in rock mass movements in the form ofroofsag, floor heave, or horizontal convergence (Figure 1)."

Jan 1, 2010

By Dakota D. Faulkner

Cable bolts anchored with traditional two component polyester resin cartridges have successfully supported difficult roof conditions in underground mines. Resin cartridges provide a costeffective cable bolt anchoring system with consistent anchorage performance characteristics when properly installed. The most commonly used cable bolts in the U.S. mining industry are 270 ksi (1,862 MPa), 0.7 and 0.6 inch (18 and 15 mm), seven-strand smooth cable with resin mixing bulbs (also known as bird cages), and 40- and 30-ton nominal capacity, respectively. However, there are other types of cable bolt anchoring systems aside from bird cages. Recently, many questions have been raised regarding the anchorage characteristics of various types of cable bolts. Keystone Mining Services, LLC (KMS), the affiliated engineering company of Jennmar Corporation, conducted a variety of controlled tests developed to closely model actual underground installations. These tests compared the performance of three commonly used cable bolt varieties, including plain, bird caged and indented seven-strand cable. Details of the laboratory testing and comparative analysis of the results are provided.

Jan 1, 2013

By John D. VandeKraats

Yielding rock bolt systems have been developed to provide ground support while accommodating shifting, creeping, or swelling ground movements. The Dywidag Systems, Inc. (DSI) Slip Nut System is one such system. It has been tested in the laboratory and installed and monitored in the interbedded halite and anhydrite at the Waste Isolation Pilot Plant (WIPP) since 1994. The Slip Nut System is installed on a point anchored threaded bar or on a threaded bar coupled to a cable bolt. At a pre-engineered load the nut acts as a die and cuts through the thread on which it rests, thereby reducing the load and coming to rest on the next thread where the process repeats. Two types of laboratory tests were performed using slip nuts on DSI's threaded bars and their Tensionable Cable bolts. Straight pull tests exceeding 0.3m (1 ft.) of displacement were performed on the systems. Also, offset tests were performed on these bolt systems in a test frame designed to simulate WIPP geologic conditions. A room scale test area consisting of 186 threaded bars began in 1994. Select bolts were instrumented to track bolt load. All bolts were tracked through time for operation. Through three complete years since installation over twelve slips, corresponding to approximately 0.15m (6 in.) of ground movement, have been observed in some areas. Since installation strata offset has exceeded 0.08m (3 in.) at a supported clay layer in the roof. No bolt failures have been observed. Slip loads observed underground generally approximate those observed in the lab. To date, the slip nut systems tested and installed have performed as expected.

Jan 1, 1998

By Chaojun Fan, Du Wenzhang, Sheng Li, Hong-Hong Shi

"Coal and gas outburst is an extremely complex dynamic disaster in coal mine production process which will damage casualties, equipment facilities and disorder the ventilation system by suddenly ejecting a great amount of coal and gas into roadway or working face. This paper analyzed the interaction among the three essential elements of coal and gas outburst dynamic system. A stress-seepage-damage coupling model was established which can be used to simulate the evolution of the dynamical system, and then the size scale of coal and gas outburst dynamical system was investigated. Results show that the dynamical system is consisted of three essential elements, coal-gas medium (material basis), geology dynamic environment (internal motivation) and mining disturbance (external motivation). On the case of C13 coal seam in Panyi mine, the dynamical system exists in the range of 8-12 m in front of advancing face. The size scale will be larger where there are large geologic structures. This research plays an important guiding role for developing measures of coal and gas outburst prediction and prevention. INTRODUCTIONCoal and gas outbursts are a complicated mine gas dynamic phenomenon that pose a serious threat to coal mine safety production. Since the first recorded coal and gas outburst occurring in Isaac coal mine of the Lule coal field in 1843, more than 40,000 outbursts have occurred in the world. China ranks first in outburst frequency and intensity. In recent 20 years, China on average increases 37 pairs of coal mines and more than 280 times outburst accidents every year (Yan, 2013). The coal and gas outburst occurred on Oct 20, 2004 in Daping Coal Mine, Zhengzhou Coal Group, caused serious gas explosions and ejected 1,894 tons of coal into the face, causing 148 fatalities. In recent years, despite implementation of numerous control measures, coal and gas outburst still occur frequently ash mining depth and mining intensity increase. The outburst mechanisms can be summarized in the following four aspects: the gas leading role hypothesis, the geostress leading role hypothesis, the chemical effect hypothesis, and combination hypothesis. The last hypothesis has won the acceptance of most scholars who consider that an outburst is the result of combined effect of stress, gas and coal (Yu, 1992).Numerous experimental measurements and numerical simulations were conducted to investigate the permeability and damage development process in coal seam. Sobczyk, et al (2011) carried out a laboratory research of the influence of sorption processes on gas stresses leading to coal and gas outbursts. Wang, et al (2013, 2015) conducted laboratory experiments to investigate the rapid decompression and desorption induced energetic failure in coal using a shock tube apparatus. Xu, et al (2006) developed a coupled gas flow and solid deformation numerical model and applied to simulate the coal and gas outbursts in underground coal mines using RFPA2D-Gasflow. An, et al (2013) and Xue (2014) analyzed major parameters and the effect of gas desorption on outburst initiation and established a model of gas migration and mechanical processes during excavation."

Jan 1, 2016

By Christopher Mark

The Analysis of Retreat Mining Pillar Stability (ARMPS) program has been used to evaluate room and pillar retreat mining layouts since it was first released in the mid 1990s. After the Crandall Canyon mine disaster focused attention on the importance of pillar design, ARMPS became an essential component in most Roof Control Plans developed by mine operators. In 2010, NIOSH released ARMPS version 6, which features a ?pressure arch? loading model for deep cover room and pillar mining. NIOSH has also provided general guidance for using ARMPS, including design criteria based on statistical analyses of an extensive case history data base. Many real-world retreat mining scenarios entail mining configurations that ARMPS does not directly address. Some of these situations that the MSHA Roof Control Division (RCD) has encountered in the course of its reviews of more than 100 ?complex and non-typical? plans are ? Unmined pillars are left at the mouth of a retreat panel that function as a ?composite barrier pillar? ? The floor is extracted on retreat, increasing the mining height ? More than one row of bleeder pillars is left in an adjacent, previously mined panel ? A retreat panel is located above or below a gob area in a previously mined seam ? Bleeder pillars are partially extracted on retreat RCD has developed solutions that allow these situations to be fitted into the ARMPS framework, and these are presented in this paper. Also discussed are some of the rules of thumb that have been developed for various input parameters, such as the treatment of inseam rock and slab cuts into solid coal.

Jan 1, 2011

By Sahendra Ram, Arnn Kr Singh, Dheeraj Kumar, Rajendra Singh

"Inherent existence of different rooms (openings) along the extraction line in a depillaring panel provides an easy path for the goaf to encroach the working area. Each of these openings in a mechanized depillaring (MD) operation along the extraction line is supported by the roof bolt-based breaker line support (RBBLS) to restrict the goaf encroachment. Different field studies by Council for Scientific and Industrial Research - Central Institute of Mining and Fuel Research (CSIR-CIMFR) found that the RBBLS works effectively during the depillaring under the shadow of stable surrounding ribs/fenders only. It is observed that, generally, these natural supports experience high value of induced stresses after a large amount of void creation inside the goaf. The induced stress creates spalling/loosening of the sides of the natural supports. Field studies also found that the positions of the RBBLS at the goaf edge need to be adjusted according to the depth of this spalling/ loosening. However, a systematic study in field for the correct positioning of the breaker line as per the spalling/loosening under different site conditions is difficult. Therefore, on the basis of the data and guidance provided by these field investigations, a detailed parametric investigation was conducted in the laboratory on simulated models for an effective design of RBBLS in a MD panel. FLAC3D is used for the simulation of the depillaring, and the available empirical formulations for Indian coalfields are used for subsequent calibration. An analysis of stress redistribution for different stages of the MD in simulated models showed the significance of the nature of overlying strata/induced stress for the RBBLS design. Discussing some results of field studies, this paper presents results of the laboratory investigations for an effective design of the RBBLS.INTRODUCTIONContinuous Miner (CM)-based mechanized depillaring (MD) is an important issue for Indian coalfields, where huge amounts of coal are locked up in standing pillars (Dixit and Mishra, 2010). Considerable variations in site conditions of these developed pillars bring a number of technical challenges into consideration during their final extraction. One of these challenges is goaf encroachment/overriding during caving of the competent roof strata. Goaf encroachment/overriding can effectively be controlled, mainly, by suitable design of natural supports (rib/snook/fender). However, there is a requirement of applied supports against the immediate roof as a considerable portion of this roof is exposed due to the presence of different openings along the line of extraction. These applied supports act as a fulcrum at the goaf edge between the working area and the goaf to facilitate the break out of the hanging roof inside the goaf. This is called breaker line support. An effective breaker line support is important for the efficiency of a depillaring operation. Generally, MD adopts roof bolt-based breaker line support (RBBLS) at the goaf edge (Singh, et al., 2014). For the first time in India, roof bolts were applied at the goaf edge as RBBLS in a CM-based MD (Leeming, 2003). In the beginning, three rows of roof bolts were installed as primary and secondary breaker lines support. On the basis of the observations of instrumented bolts, only two rows of roof bolts were used as secondary RBBLS (Ram, et al., 2014). Now, most of the MD operations in India are using only two rows of bolts as RBBLS (Table 1). However, the strata mechanics studies at different MD operations showed interesting characteristics resulting from this support (Ram, et al., 2015)."

Jan 1, 2016

By Wojciech Masny, Andrzej Walentek

"The most common extraction method in Polish coal mines utilize pillars between adjacent longwall panels. This is mainly due to the significant depth and difficulties in maintaining stability of the gateroads. This paper presents measurements of entry convergence and range of the fracture zone around a gateroad measured with a borehole camera. The entry where the measurements were taken was located in a parallel entry separated from the gateroad by a 5-m- (16-ft-) wide pillar. The gateroad was located in a hard coal seam 900 m (2,952 ft) deep with a dip of 5°. The extraction method was longwall mining with caving and the mining height was about 3 m (10 ft).Furthermore, the ""in situ"" measurements were compared to the convergence forecast for the gateroad and fracture zone by means of numerical modeling conducted using the Phase2 Version X.X finite element program from Rocscience. The determination of the fractured zone around the openings is of great importance to successful mining practice, especially in support planning and design for longwall gateroads. Moreover, proper determination of the fractured rock zone is one of the basic elements in the process of planning the roof bolting for mine workings.INTRODUCTIONIn the Polish. hard coal mining sector, retreat longwall extraction is most commonly used (Prusek and Masny, 2007). This method is connected with the necessity to carry out a number of development operations during the first stage, including among others, driving of gateroads and a setup room.Currently, most Polish mines eliminate gateroads behind the extraction front, using the ""U"" ventilation system (Szlitzak et al., 2008). In such cases, one of the roads for the next longwall panel is driven along the caving goafs, leaving a protective pillar of some chosen width (Figure 1). The question regarding the width of the coal pillar is especially important to the stability of the gateroads that define the panel for the subsequent longwall. When analyzing the previous experience relating to this type of pillar (Junker, 2006; Rajwa, 2008; Stranzet et al., 1973; Betriebsempfehlung, 1982), one can state that there exist two solutions for the determination of its width."

Jan 1, 2010

By Craig Byington

The stress-field orientation mapping and analysis (SOMA) technique for determining the operative stress field near mine workings and its relationship to various fracture sets is described using Dickenson-Russell Coal Company's Laurel Mountain mine as an example. Carried to its practical application, this technique ultimately defines the optimal orientation for the mine workings wherein pillars, rather than rock bolts or other roof support methods, dominantly shoulder support of the highest-probability, potential, roof-fall blocks. It also provides a predictive tool describing local variability in rock deformation and in secondary roof support methods. Fracture discontinuities within a rock mass, either as pre¬existing natural fractures or as mining-induced fractures, are uniquely necessary for every brittle-deformation ground failure including roof falls. Prediction and mitigation of roof falls requires quantifying the interaction between the fracture sets and the operative principal-compressive¬ stress-axis orientation (olo). The SOMA technique utilizes the interaction between fractures and 61o, specifically their dilation or closure, to calculate the orientation of 610, and to estimate the orientations of 62o and o3o. A stereonet program is used to organize and statistically analyze the fracture data, and then to determine the optimal orientation for the mine workings. The final step in the SOMA technique involves modeling the Laurel Mountain mine using a 2-D, finite-element, modeling program. This assures that the interpretations regarding the optimal working orientation closely match the deformation features observed in the mine. It also provides a predictive tool describing highly variable stress and strain partitioning, seemingly erratic rock-bolt failures and the interactions between different sets of mine workings within different coal seams. The critical importance of including the fracture sets is well illustrated in the Laurel Mountain mine where the effects of earlier mining of an underlying seam is contrasted in both a fractured and otherwise identical non-fractured model to illustrate the consequences of ignoring fractures in a predictive roof-fall model.

Jan 1, 2004