Search Documents

By Jeffrey J. Schwoebel, Jianliang Li, Daniel J. Brunner

A United Nations (UN) administered degasification technology transfer project, funded by the Global Environmental Fund (GEF) is underway at the Shihao Mine of the Songzao Coal Mining Ad- ministration in the province of Sichuan, Peoples Republic of China. This mine exploits multiple seams at depths ranging from 300 to 600 m below surface. In-seam boreholes and frequently spaced in-mine vertical boreholes, developed from underlying galleries constructed specifically for this purpose, currently degasify the seams in advance of mining at the Shihao Mine. Because of ventilation system constraints and the in-situ gas con- tent, longwall mining of the coals at this mine could not proceed without some form of pre-mining degasification. This paper presents a simulation based degasification plan of long, in-seam horizontal boreholes for the Shihao Mine. Simulations with a coalbed reservoir program assessed time dependent degasification characteristics of both vertical and in-seam horizontal boreholes. The simulations used input data from reservoir and desorption tests conducted at the mine site. The results produced system design nomograms to assist mine engineers in defining the appropriate borehole spacing necessary to degasify the seam in the time available for pre-mining drainage. The predicted effectiveness of the current vertical degasification scheme was compared with that for a horizontal borehole program and served as the basis for the recommended in-seam borehole configuration for the project at the Shihao Mine. The horizontal borehole degasification program requires substantially less gallery and borehole development than the present vertical degasification scheme.

Jan 1, 1997

By R. L. Wiegel

Several mineral process modeling and simulation packages are currently available for use in evaluating the performance of alternative process flow schemes. A critical link that has been missing from these packages is the ability to quantitatively model the effect of size reduction on the liberation of the valuable and waste minerals in the ore being processed. Although there have been several approaches taken to this problem over the past 25 years, none of them has led to a satisfactory conclusion. A technique was developed for measuring the effective liberation characteristics of magnetic taconite ores, and a program was constructed that makes use of these liberation characteristics in simultaneously simulating both size reduction and mineral liberation as it occurs in tumbling mills. This is an especially important step in the modeling of magnetic taconite processes, where magnetic rejection of low-grade wastes between grinding stages mandates that a predictive capability be available. The current application is specific to magnetic taconite, but it is possible that a similar approach could be used for other types of mineral systems. Key words: Modeling and simulation, Size reduction, Mineral liberation, Taconite, Magnetic concentrator

Jan 1, 2003

By Y. Zimmels, C. Feldman

Closed-circuit grinding processes are considered in the context of a reactor-separator circuit that involves multifraction streams and products. Because grinding circuits are low-efficiency, capital-intensive operations, modeling to maximize their economic return is appropriate. An attempt to develop and test such a model is presented in this work. The model relies on process simulation for both the mill and the separator, in conjunction with constraints imposed by product specifications. The grinding process was simulated using breakage functions, which provided complete data on the feed and product of the mill. A cyclone bank used as the separator was also simulated using known models. The overall process model provided a complete simulation of the multistream grinding and separation process. The process model was then incorporated into an economic model that predicts grinding cost, subject to process constraints, for a given set of operating variables. The model facilitates economic optimization of the grinding process as it relates to process variables and process hardware.

Jan 1, 1993

By P. N. Thompson

The past few years have seen the introduction of mini-computers on an increasing scale at collieries in the British coal industry. These are being used for controlling underground transport systems, coal preparation plants and fixed plant (pumps etc.); and for monitoring the mine environment and face operations.. A separate mini-computer (termed a primary computer) is dedicated to each of these functions. The overall system under which these computers operate is a common one which is applicable at all collieries. The information collected by the primary computers, other than that required for immediate control, will be fed to a secondary computer for analysis and processing. This overall concept, called MINOS. (MINe Operating System) is being developed by the National Coal Board's Mining Research and Development Establishment (M.R.D.E.). Eventually most of the data required by the system will be captured automatically. For example, the fact that a delay has occurred on a face, together with the duration of that delay, will be detected automatically via transducers link linked to a primary computer. However, the reason for that delay will, in all likelihood, have to be recorded manually. Such a system is currently under development with the first trial installations now being made.

Jan 1, 1979

By Otis M. Clarke

Domestic bauxite used in aluminum production comes from Arkansas where syenite was lateritized forming bauxite. Part of the residual bauxite and kaolinized syenite were eroded, deposited downdip, lateritized with bauxite formed in place, and covered by sediments. The unconsolidated overburden causes problems in mining. Bauxite for refractories and chemicals comes from Alabama and Georgia. Sediments were deposited in karst lakes and were lateritized forming bauxite and kaolin. Ferruginous bauxite in Washington, Oregon and Hawaii, derived from weathered basalt, can be used in aluminum production.

Jan 1, 1984

By Harry Perry

The decline in coal production has been slowed somewhat in recent years, mostly because of the industry's own remarkable success in holding the line on costs, and partly as a result of advances achieved through industry and government research. Nevertheless, the decline has continued. This downward trend combined with the increased productivity of labor through mechanization that has been necessary for coal to retain even its present competitive position, has resulted in a serious reduction in the number of miners required and large scale economic dislocations in mining communities. For coal to regain a more favorable position it must either expand existing markets by reducing the cost of the delivered product and thereby compete more effectively with other fuels or develop new uses that will require large tonnages of coal. New markets involving several million tons, which would look extremely attractive to most other United States industries--including the organic chemical industry--would do little to alleviate the coal industry?s depressed economic conditions, While such small new markets would be welcome, an industry producing over 400 million tons per year must look to large tonnage outlets for solutions to its long range economic problems.

Jan 1, 1964

By S. K. Das

A detailed strata-mechanics investigation and examination was carried out in the E2 Panel (ML-II/7) of the XVI Bottom coal seam, which is located in the Moonidih Colliery of B.C.C.L., Jharia coalfield, India. Above this panel, the XVI Top coal seam was previously worked out by a longwall panel. Based on intensive field study and on experiments in a number of longwall panels located within various Indian coal mines, the actual behavior of the coal roof strata was evaluated and new strata-mechanics concepts around the longwall panels were developed. These concepts resulted in new methodologies concerning the behavior of roof rocks, caving characteristics, etc. within longwall panels and in the area of strata mechanics. Based on these new strata-mechanics concepts, a very simple, but realistic, model was developed to determine the optimum capacity of the powered supports. This model considered the combined loads resulting from the detachment of strata and composite layer blocks from the face and, also, loads due to the deflection of strata and composite layers situated above the detached roof rockmass. This formula, along with the other related formulas by the author, prompted the determination of the optimum capacity requirement for the powered supports to be used in the XVI Bottom coal seam, located under the worked out area. This new concept in strata mechanics and capacity requirements of the powered supports in a longwall face may be an aid to Mining Engineers.

Jan 1, 1997

By F. N. Kissell

The US Bureau of Mines undertook a study of those factors influencing worker escape from an outby coal mine fire. The results of this investigation were two-fold. First, those factors affecting escape from a mine fire were defined, and second, the relationships between these factors were identified. Although the individual components had been studied before, little information was available on their interdependence. Fault tree analysis was used to evaluate the miner escape scenario. After constructing the fault tree, a two-phase analysis of the tree was conducted. During the first phase, the minimal cutsets of the fault tree were identified and ranked. These sets were the smallest sequence of events leading to fatalities during the fire. This ranking revealed that reduced evacuation delays, improved self-rescuer training, and improved stopping construction were important in controlling fatalities during escape from the mine fire. The second phase involved additional analyses of the fault tree. These evaluations were started by first determining occurrence probabilities for each event in the fault tree. Two types of sensitivity analyses were then conducted. The first analysis dealt with changes in event probabilities and their impact on the likelihood of fatalities. The final sensitivity analysis considered dramatic reductions in the probability of fire fatalities. This revealed what event probability values were necessary to reach this level. These results have revealed various remedial actions that could be used to improve the survivability of an outby mine fire.

Jan 1, 1990

By B. Jensen, R. Davis, P. Golledge, A. D. S. Gillies, W. Urbanik Urbanik

A current program of research on the explosibility of coal dust/methane mixtures is described. During the study an explosion test chamber based on a novel design has been developed. This 20 litre open chamber uses a rotating drum concept for dust dispersion and infra-red sensors for dust concentration measurement. The chamber design allows different initiators to be tested while varying methane gas and coal dust concentrations. A new approach to the determination of coal dust concentration is included with a description of a dielectric dust probe. The measurement technique is based on the change in dielectric constant as the proportion of coal dust in air between probe capacitor plates increases or decreases. Characterization of coal dust samples is of vital importance. The particle size distribution, coal proximate analysis and elemental analysis were studied. Coal dust was sourced from airborne collected samples, settled dust from mine sources and seam channel samples crushed and sized. Explosibility test results indicate that a very low concentration of coal dust can form an explosible mixture when dispersed in methane concentration of just below five percent. With low temperature initiators, the coal dust lean limit concentration rises rapidly as the methane concentration is reduced. An accurate knowledge of the potential explosion hazards of coal dust and coal dust/methane mixture is necessary to establish safe operating conditions in underground mines. The research results outlined extend knowledge in this area.

Jan 1, 1989

By Steven J. Page, Robert A. Jankowski, John A. Organiscak

Quartz dust is one of the most significant ongoing health concerns in coal mining today. Since initial verification of this health risk in coal mines by the Mine Safety and Health Administration (MSHA) during the early 1980’s, the Bureau of Mines has conducted numerous studies in underground mines to identify the sources of quartz dust and its fundamental characteristics. The most significant underground quartz dust source was found to be the continuous miner excavating rock. The percentage of quartz was also found to be higher in the smaller size fractions of the dust when significant amounts of rock was mined by the continuous miner. Furthermore, the quartz content in the continuous miner return remained fairly consistent at greater distances from the face. Another important factor speculated to affect quartz dust generation and its size characteristics is the morphology of the quartz bearing rock. The quartz content of dust between mines had notable differences with respect to the differences between kaolinite content in the dust. Low kaolinite content was associated with higher quartz content and increased size segregation of quartz into smaller dust particles, indicating that the free silica bonding matrix in the rock is most likely another factor responsible for quartz dust produced through mechanical comminution.

Jan 1, 1991

By Allan E. Hall, Stephen G. Hardcastle, Lucien D. Nel, Jean-Paul Saindon

A description is given of the investigation conducted at Sherritt Gordon's Ruttan Operation in Manitoba during 1986. Gas and dust concentrations were measured in the exhaust air of the major working sections to assess the potential for recirculating exhaust air into the intake air in winter to reduce heating costs. The results indicate that there is excellent potential to significantly reduce winter heating costs by controlled recirculation of exhaust air. Gas and dust concentrations vary significantly during the working shifts but have consistent trends from shift to shift and day to day. The variations in gas concentrations have similar trends but no single gas could be reliably used to predict the variation of the other gas or the dust concentrations. Dilution and the other effects which reduce pollutant levels as the exhaust air returns to surface indicate that recirculation should take place as close to surface as possible, subject to the economic constraints of the airway construction required and the extra fan energy required for the longer recirculation path. Recommendations are made for the choice and positioning of air and dust monitoring sensors and the logic of a control system. Economic analysis of the results indicates that controlled recirculation is viable at an existing mine with a pay back period of approximately two years. Incorporation of a system into a new mine at the planning stage would significantly shorten the pay back period.

Jan 1, 1987

By F. Michael Wahl

With the exception of reports on commercial deposits of kaolin, fuller's earth, and other specialty type clays, there is little published information on the extent, properties, and potential uses of the clay resources of Florida. Recent studies by the Florida Bureau of Geology in cooperation with the University of Florida and the U.S. Bureau of Mines have proven the existence of two extensive Miocene clay deposits, one in peninsular Pinellas County and the other in southeastern Charlotte County. Drilling and subsequent testing of the clays from these deposits indicate their potential for economic development. Both deposits consist of montmorillonite type clays, have an average thickness of 25 to 35 feet, and are overlain by unconsolidated Pleistocene sediments. Preliminary firing tests indicate that the clays from Pinellas County are a potential raw material for lightweight aggregate production. The clay has good bloating characteristics across an acceptable temperature range with a resultant aggregate density of less than 1.00 specific gravity. The clays from Charlotte County have poorer natural bloating characteristics but might well be used after treatment or with additives. The economic potential and locations of both deposits emphasize the need for locating similar clay resources in the state that might have economic potential so that land use planning and subsequent urbanization will not prohibit their development.

Jan 1, 1972

By D. A. Day, H. L. Marsh, P. J. Stephens, C. A. Wiggins

Lightweight cellular grout backfill behind pipe-in-tunnel has been gaining increased acceptance in the tunneling industry and has proved to be both practical and economical. Two successfully constructed projects, the Upper Scioto West Interceptor Sewer (USWIS), in Columbus, Ohio and the Benbrook Pipeline Tunnel Project in Fort Worth, Texas will be discussed. The projects represent two different but successful applications of lightweight cellular grout backfill. The USWIS placed the grout behind precast reinforced concrete pipe, in water bearing limestone, and in close proximity to residential water wells. The Benbrook Project placed grout behind 6,096 meters (20,000 feet) of steel pipe from just two locations, eliminating major surface disruption typically associated with the placement of pumped concrete.

Jan 1, 1999

By L. Xu, N. I. Jayaraman, R. Bhaskar

The objective of this study is to develop a better understanding of the collection characteristics of dust measurement instruments used in mine dust control research with respect to properties of quartz and coal dust. Coal and quartz dust of narrow sues, with aerodynamic median diameters being approximately 2 µm, 4 µm and 10 µm, with quartz contents of l0%, 20%, 30%, 40% and 50%, were released in an aerosol characterization chamber using a fluidized bed aerosol generator. Dust was collected in MSA personal gravimetric samplers with l0-mm nylon cyclones, total dust samplers and Sierra 298 inertial cascade impactors. The samples were analyzed for mass and quartz content. A total of 21 experiments were performed for this study. The mass and quartz collection efficiencies of the total and respirable dust samplers and the impactor were determined. The data show that the amount of dust collected by the respirable dust sampler (respirable + oversize dust trapped in the cyclone pre-classifier) was, in general, less than the amount collected by the total dust sampler. The amount of dust collected by the impactor was higher than that collected by the total dust sampler. Quartz analyses of the airborne dust samples showed that the total dust and respirable dust samplers (including oversize dust) collect less quartz dust than at inertial impactor. The larger the median particle sire of the quartz and coal mixture, the lower the quart content of the dust collected in the samplers. For all three sires, the impactor was a better collector of quartz than the other instruments.

Jan 1, 1994

By Robert A. Wilson

Los primeros pasos básicos para determinar los valores reales y los minerales concernientes, que son la base para las pruebas metalúrgicas, son presentados en este capítulo. A continuatión, eligiendo el proceso o los procesos indicados para el tratamiento de un mineral, son expuestos los temas. Todo esto es seguido por los procedimientos utilizados, el resultado de los cuales indicará la viabilidad para el tratamiento. Estas pruebas de procedimiento han sido desarrolladas, utilizadas y de probada efectividad en laboratorio con evaluaciones relativas al procesamiento de la planta. Los procedimientos especiales y poco comunes se encuentran fuera de la finalidad de este capítulo. La evaluatión de los resultados de las pruebas y su incorporatión dentro del flujograma preliminar y final para el diseno de la planta son temas igualmente expuestos. El valor de un flujograma, con balances de material y agua para el diseño de la planta, es asimismo mostrado.

Jan 1, 1982

By B. P. Mohanty, D. A. Shores

During the induration of fluxed taconite pellets, alkali salts deposit on the grate support bars, causing severe corrosive degradation of these alloys. To determine the source of these deposits and to understand the mechanism by which the salts are conveyed to the grate bars, a study of the reactions between fluxed pellets and combustion gas was carried out. The study focused on the thermodynamics and kinetics of several processes associated with induration; namely, oxidation of magnetite, calcination of flux, and the formation and gaseous transport of various alkali salt species. Both theoretical and experimental techniques were used. It was concluded that the principal source of alkali salt deposits is alkali chlorides, which are present as contaminants in the flux and/or residue from contaminated washwater. The pathway from pellet to grate bar involves the following steps: evaporation of chloride salts within the pellet; diffusion of salt vapor out of the pellet, aided by the outflow of CO2 from calcination of the flux; convective transport by the combustion gas with concurrent (partial) conversion to alkali sulfates by reaction with residual SOX in the combustion gas; and condensation of salts on the grate bars.

Jan 1, 1998

By Faruk Oksuz, Cary Hirner, Ray Brainard

"Key project participants, including owners, engineers, and contractors continually seek for sound and structured decision analysis on how to select the best contracting method for successful project delivery. In addition to being burdened with technical challenges, lack of resources, budget shortcomings, regulatory requirements, and bureaucratic and politically mandated obstacles, the project participants need a reliable decision analysis model on the best project delivery method. The pendulum of choice for contracting continually swings back and forth between traditional design-bid-build and alternative delivery options such as design-build, progressive design-build, construction manager at risk, and public-private-partnership. For large tunnel projects, the decision process is further complicated due to contract packaging options as well as risks in underground construction. Contracting strategies for large tunnels require thorough consideration of performance, risk, quality, operability, cost and schedule. This paper compiles an array of decision making criteria and tools for an unbiased and balanced evaluation and ranking system in the procurement of large tunneling projects. INTRODUCTION Successful project delivery hinges upon meeting the owners’ expectations and key performance indicators. Large tunneling programs benefit from a thorough understanding and successful implementation of project delivery options by key project participants including the owners, engineers and contractors. The key to success is a collaborative advancement of project as the key project participants knowledgably address the applicable management, performance, risk, quality, cost, operability and schedule considerations throughout a project realization cycle. PROJECT REALIZATION CYCLE All projects have customary planning, design, construction, commissioning and operation phases that may seem to be sequential but in reality that are well integrated and dependent on one another. A glitch in any phase of a project realization cycle could hinder a successful outcome and none of the project partners are immune to consequences whenever and wherever they may surface."

Jan 1, 2016

By Keith S. Liddell

Gold in many ores occurs in sulphides, which, if the gold is finely disseminated, renders the ore refractory and therefore not amenable to the simple process of milling and cyanidation. Traditional methods of treatment of these refractory ores is to produce a sulphidic flotation concentrate which is roasted to form a porous calcine from which the gold is recovered by cyanidation. The roasting process imposes a constraint of a minimum sulphur grade of the concentrate on the flotation plant, which may lead to a lower gold recovery being achieved in the flotation section. Thermal decomposition of the concentrate by roasting means that the sulphur contained therein has to be treated and disposed of in an environmentally acceptable manner; and, if arsenopyrite is present in the concentrate the environ- mental aspects will be worsened. It has long been recognized that finer milling of gold-bearing materials improves the liberation of gold, especially when the gold particles are very fine. After extensive laboratory and pilot plant investigations (Liddell, Patents), a suitable mill has been developed for the mining industry by Metprotech, which is capable of producing very fine grinds (down to 90 percent passing one m if necessary). In the course of the investigations it has been found that a large number of gold-bearing materials are amenable to fine milling. A specific advantage that fine milling of sulphidic materials has over oxidative processes such as roasting and bacterial leaching is that the sulphides are not decomposed and there is therefore not a sulphur disposal problem. Furthermore, the milled sulphides can become a future sulphur feed source, and can be reclaimed if necessary. A further feature of the Metprotech process is that it is possible to add cyanide to the mill feed

Jan 1, 1988

By G. Lodewijks

Today most belt conveyors used for the transportation of bulk solid materials are driven in a centralized way with all drives in one location. The dynamics of these systems has been studied since the early seventies of the previous century and are well understood. Compared to the more conventional belt conveyor system with a centralized drive station positioned at the head and/or tail of the system, a decentralized driven layout with drive stations distributed along the whole length of the belt offers a number of advantages. However, to make a decentralized driven configuration a good alternative to a centralized driven, the system designer will have to balance these benefits with the increased complexity. The full potential of a decentralized driven system can only be realized if the right balance is found between the locally applied drive force and the motion resistances occurring along the system. From previous research it was found that in a multiple driven belt conveyor system the most dominant belt behavior occurs in the belt section between the tensioning device and the first drive station. In this paper different possibilities are analyzed to improve this dominant belt response and optimize the starting behavior. This can be accomplished by changing the predescribed start up profile, starting the drive stations in sequence rather then all at the same time and altering the locations of the drive stations.

Jan 1, 2008

By K. S. E. Forssberg, M. I. Hallin

In many cases, the reuse of process water in flotation plants is desirable both for plant operating reasons and for environmental protection. The main advantages are better housekeeping of fresh water and process chemicals together with the reduction of polluting species to the environment. There are however a number of problems involved in the use of recycled process water. The main problem is that recycling sometimes has a deterious effect on the process and can occur months after the start of water recycling. The Division of Mineral Processing of Luleå University of Technology has been conducting experiments on recycling of process water at various sulphide plants in Sweden for over ten years. The experiments have been carried out in pilot- and full industial scale, in collaboration with the mining companies operating the plants. Until 1988 investigations were carried out in four different sulphide plants. The objectives of the experiments were: first to document differences in the composition of the process water during recycling; secondly to investigate any changes in the pulp chemistry of the flotation circuits wich may be due to the influence of recycled water; and lastly to establish critical levels, if any. of the parameters measured. While conducting experiments of this kind several things have to be kept in mind. Normally, recycling is done by using tailings pond water as process water. This means that time effects are important, because of the time lag between water input in the tailings pond and the reclaim of that water back to the plant. As will be shown, the

Jan 1, 1989