Search Documents

By R. C. Hopper, A. A. Mathews, T. A. Lang

DESCRIPTION OF PROJECT The Straight Creek Tunnel site is located approximately sixty (60) miles west of Denver, Colorado, on Interstate Route 70 in the vicinity of Loveland Pass, in the Rocky Mountains. The ultimate project will consist of dual two-lane vehicular tunnels with a building at each portal to house mechanical ventilation equipment and other installations. The tunnels run virtually east-west on an ascending 1.64 percent grade for a distance of approximately 8,900 feet, and will pass beneath the Continental Divide at an elevation of about 11,000 feet above sea level. The maximum cover is 1,450 feet and each tunnel is approximately 48 feet wide by 50 feet high as excavated. The work now under construction consists of the North Tunnel, which initially will have two-way traffic. Ultimately it will be the west bound lanes for Interstate 70. The completion of the North Tunnel will be the fulfillment of a long felt need for better communication through the high Rocky Mountains of central Colorado and is a vital link in Interstate Route 70. The early planning for a vehicular tunnel through the Continental Divide began in the late 1930's and between November, 1941 and May, 1943 an exploratory pioneer tunnel

Jan 1, 1997

By Robert Stefanko

The widespread and increasing use of electrical power for mechanized power has made a tremendous impact on the coal mining industry. It is probably the single most important factor influencing the productivity of a coal mine. In fact, as a part of a study of 62 coal mines in Pennsylvania and northern West Virginia, plus information that was obtained from other sources, it was possible to show a direct correlation between the rise in the use of electrical power and mine productivity, Figure 1. This increased power demand has not always been achieved through proper planning and a careful evaluation of all design parameters, many of which are not even recognized. The result has been increasing problems in power distribution and utilization establishing the need for scientific studies including considerable underground measurements. Because the cost of power for ton of coal produced is generally a relatively low value, inadequate attention is paid its distribution and utilization. Furthermore, a poor system of records and a lack of adequate measurements add further to a paucity of statistical evidence that would permit a rational analysis of overall power costs. However, the direct cost figure alone is highly deceptive; of much greater value is the indirect costs associated with the use (or misuse) of electrical power underground. Success in highly mechanized mining correlates directly with equipment utilization. Today's machines have tremendous potential capacities but profits are measured in terms of performance and not potential. Thus the reliability of electric motors is an extremely important factor for consideration and the effects of all parameters should be carefully evaluated. Thus while studies are continuing on the evaluation of primary and secondary mine electrical systems with interesting results, this paper will be limited to reporting on the results of a study of a specific motor application.

Jan 1, 1972

By R. C. Keaney

The metals industry is in complete chaos with mines being shut down, profits becoming non-existent, and continual losses to imports from other countries. Yet the raw material supplier to the glass industry has many opportunities to grow and to produce profits. Fortunately, the cost of most glass raw materials are low enough that competition from imports is not anywhere as critical as it is in the metal industries, such as copper, aluminum, lead, and others. But the glass raw material supplier must develop new products, both chemically and physically, to effectively compete in the future. The purpose of this paper is to point out generally where these opportunities exist and to suggest how they may be further developed. As the glass industry looks for energy saving materials, they look once again towards finer materials. A glass furnace is now approximately 40% efficient. Glass engineers are constantly striving for energy savings and it is well known that finer materials melt easier so that the manufacturer can operate his furnace either at lower temperatures for the same production or he can produce more material at the same temperature. The old 20 mesh sand specification is no longer sacred and as the mesh size for sand changes so do the specifications for all other raw materials used in the melting process. Highly instrumented glass furnaces can now measure quite accurately the energy needs to produce glass and can also measure the energy loss in each furnace. Glass technologists desire today a sand with a top size of 40 mesh while some would like to have the top at 60 mesh. This becomes more difficult to accomplish as a raw material supplier without .grinding. As you well know, grinding develops fines. Yet the same technologists will tell us that we can have nothing passing a 140 mesh screen. Therefore, we must develop processes which allows us to produce a finer screen size without increasing the amount of fines passing through the 140 mesh screen. To counteract this, different and changing industries are now demanding much finer products so possibly there will be markets for the fines which are currently separated out of the products. Methods that are practical and low cost must be found to develop different products with different screen specifications. What works for sand can be carried over to the other raw materials used in melting. Among the answers to finer products, of course, are pellets. Aglomeration or pelletizing has been looked at in the past and will be looked at in the future. Considerable work has been done in the glass container industry on this and must be carried out more extensively. By using aglomerated material or pellets, the glass producer will gain the benefits of melting fine materials without suffering from handling or dust problems. Pelletizing, particularly where using basic glass melting materials such as burned lime or sodium silicate, will not only produce a good pellets but will add desirable minerals to the glass batch.

Jan 1, 1986

By Gary L. Nelson

An overview is provided of Franklin Industrial Minerals mica mine and plant operations located near Velarde, New Mexico. Operated by Franklin Industrial Minerals since July of 1990, several process and product modifications have been developed and instituted to improve the operation. In addition to a brief history of site operations, descriptions of the mining, beneficiation, delamination grinding, and product classification processes are reviewed. Supportive topics discussed include equipment modifications and improvements, product application diversification, and specific product characterization. Also reviewed are the key areas of safety, environmental responsibility, and programs pertaining to process quality control and product quality assurance.

Jan 1, 1994

By G. T. Adel, W. Z. Choi

A model describing size reduction and mineral liberation during grinding has been extended to include multiple classes of composite particles. The majority of the model parameters have been directly determined using computerized image processing equipment to analyze the products from batch grinding tests. A coarse-grained sphalerite ore from Tennessee, representing a nearly ideal binary mixture of sphulerite and dolomite, has been used to experimentally validate the model for the case of dry batch grinding. In all cases, excellent agreement has been observed between the model predictions and the experimental results.

Jan 1, 1988

By William G. Davenport, Eric H. Partelpoeg

Direct smelting of copper in a single vessel has long been the extractive metallurgist's dream. Such a process offers the important advantages of (i) maximum use of the energy available from oxidizing the sulphur and iron of the concentrate; (ii) restriction of SO2 emissions to a single constant-strength source; (iii) minimum materials handling and (iv) elimination of at least one process step. Extensive developmental work was carried out in the 1960's and 1970's to implement such single-step processes. Some of the processes reached the prototype stage and it appeared that copper smelting technology was on the threshold of a new, efficient, minimum-pollution era. Since that time, however, the forward thrust has slowed and single-step smelting is still a process of the future. The paper describes in detail the potential advantages of single-step smelting; its history and current status; and the reasons why it has not been adopted industrially. It concludes that the potential benefits of single-step smelting are powerful and that many of the difficulties encountered in the 1970's will be overcome in the 1980's.

Jan 1, 1985

By E. Pardo-Igúzquiza

Most mining applications of geostatistical simulation are to the simulation of quantitative variables, such as grade. In many instances the occurrence of quantitative variables and the values they take are controlled, at least partially, by qualitative, or categorical, variables. Examples include quartz-vein controlled gold orebodies and stratigraphic silver/lead/zinc deposits. In these cases a realistic simulation must include geological controls on the spatial distribution of the simulated quantitative variables. This paper describes extensions to, and algorithms for, the truncated plurigausian method of simulating categorical variables. The categorical variables are modelled as indicator random functions that represent the presence/absence of the variable at spatial locations. Stochastic images of the distributions are obtained by truncation of realisations of two Gaussian random functions simulated at the same locations. Parameters required are the thresholds for truncation of the Gaussian variables and the covariance structure of each Gaussian random function. These parameters are estimated from the experimental proportions of each variable and indicator direct and cross semi-variograms. A detailed case study is shown in order to illustrate the procedure, to discuss the results and to present the algorithms for plurigaussian simulation.

Jan 1, 2002

By G. T. Adel

The selective recovery of fine particles by flotation has been a long-standing problem in the mineral processing industry. Fundamental studies carried out at Virginia Tech since 1980 have suggested that many of the problems encountered in separating fine particles can be alleviated by using significantly smaller air bubbles than those used in conventional flotation processes. The main advantage of using smaller bubbles is found in an increased recovery rate, which can be attributed to an improved bubble-particle collision efficiency. This concept has been applied in column flotation as a means of improving flotation kinetics. A computer simulator has been developed to better study the effects of various parameters on flotation column performance. The simulation results suggest that the use of small bubbles and tall columns improves the recovery of fine particles while a judicious use of wash water greatly improves product quality. Information collected as a result of this analysis has been applied in developing scale-up relationships for column flotation.

Jan 1, 1989

By L. A. Morley

Electricity is a major cause of lost-time accidents and fatalities in the mining industry. Major hazards and unsafe practices that contribute to electrical hazards are identified in this paper. Recommendations for reducing electrical accidents in surface mining are given and are directed toward the following three areas: preventing equipment contact with overhead lines, preventing maintenance related accidents, and defining system protection techniques.

Jan 1, 1986

By Wallace W. Wilson

It scarcely 1s possible to read a new issue of any of the principal mining trade journals without noting some mention of a major new overseas mining venture with which one or more domestic companies are involved. These projects seem to follow a fairly consistant pattern; most are large open pit mines, with relatively low grade ore bodies but huge reserves; the total price tag will be in nine significant figures and around half or more of the total cost will be for infrastructure. West1 noted that nearly $7 billion is being invested annually for new mining projects and the expansion of existing mining ventures, in the free world. He anticipates that by the year 1975 such investments would reach the $10-11 billion annual figure, and that in the five year period 1972-76 total capital requirements can be expected to aggregate around $45 billion. The proportion of this total investment which will be financed in some manner is difficult to estimate because of the variety of available financing arrangements. West estimated that around 75% of the total capital would come from internally generated funds, with the balance from external sources. Conceivably a substantially higher percentage could be attributable to external financing, especially it the trend of recent mineral development in Canada and Australia is any criterion, and of course, including local sales of equity as a part of the package.

Jan 1, 1973

By Kent S. Roessler

The Bureau of Mines is currently investigating the geophysical application of Tomography to monitor leachate during in-situ mining. Determining the location of the leachate is important for both economic and environmental reasons. By analyzing a sequence of tomographic images, we can determine where highly permeable/fractured regions are located and hence, major flow paths. Since BOMTOM (Bureau Of Mines TOMography - Tomographic Reconstruction Program), and BOMCRATR (Bureau Of Mines Curved RAy Tomography - Tomographic Reconstruction Program) are sensitive to user-selected ray path arrival times, we are also investigating the use of neural networks to automate the process of recognizing this feature. This paper presents a technique for detecting fracture zones and their orientations in a region between two boreholes, by using a motion analysis study of a sequence of tomographic images. It also addresses the need for an automated/unbiased method to pick crosshole seismic arrival times using a trained neural network. In exploration geophysics, the picking of first break arrivals represents a pattern recognition task. The neural net paradigm has proved to be a good method of solving this type of task. To pick the first arrival peak of a trace, the network is trained with a set of known (user selected) first arrival peaks by creating a binary image of a set of traces. Once trained, the neural net correctly picked first arrivals of the remaining traces in the set.

Jan 1, 1992

By J. W. Mahar, E. J. Cording, F. L. Gau

INTRODUCTION The Washington, D.C. rapid transit system (METRO) when completed will consist of 98 miles of double track rail. Fifteen miles will be tunneled in rock and 12 large underground rock chambers will be constructed at station locations. The University of Illinois is under contract to Metro to provide observations and instrumentation services in the initial phase of construction. The work is coordinated through DeLeuw, Cather & Co., the General Engineering Consultant to Metro. The program is designed to monitor construction conditions as well as to provide information useful for the design of future rock tunnels and rock chambers in the Metro system. This paper presents the results of observations in the rock tunnels constructed to date. Most of the observations are in a 5000-ft-long, 30-ft-wide, double track tunnel in downtown Washington, D.C. Observations were also made in single track tunnels, shafts, enlargement areas, and pilot tunnels, and are being made in a large rock chamber 700 ft long, 76 ft wide, and constructed at shallow depth in a schistose gneiss. One of the major objectives of the observational program was to determine the orientation and character of joints and shear zones and to evaluate their effect on support requirements for various tunnel orientations and configurations. The consistency of geologic features throughout the Washington area has made the results of the initial study applicable to evaluation of support requirements on future tunnel contracts. The first section of this paper summarizes the geologic conditions in the tunnel and their effect on overbreak and rock movement.

Jan 1, 1997

By John J. Schanz

The ideal entering freshman for the College of Mineral Industries possesses the necessary aptitude to complete successfully a difficult technical curriculum, has a highly developed intellectual curiosity and adequate preparation in basic mathematics, sciences, and English, is enthusiastic about pursuing a career in the mineral industries, and puts forth a good academic effort while attending Penn State. The present programs of the University?s Division of Counseling and the College of Mineral Industries are directed toward providing the College with students who will meet these requirements. At present, freshmen are admitted to the Pennsylvania State University without entrance examination if they are in the upper two-fifths of their high school classes. All Pennsylvania students in the lower three-fifths are required to take the University Aptitude Test and all out-of-state students the College Entrance Board Examinations. Such students are admitted only if they score sufficiently high on either test to indicate the ability to do satisfactorily the work of University students. Only to this extent, are native intelligence and areas of greatest aptitude known for the Freshman prior to admission, and they are, therefore, largely beyond the control of either the Division of Counseling or the College of Mineral Industries. Because all freshmen, with exceptions that are numerically minor, are required to select a curriculum before admission to Penn State, each student who presents himself for required counseling during the summer, prior to his first semester, has already made a choice of his course of study. In many instances, such choices have been made without a rational and serious consideration of the student?s abilities and interests. Through tests given between the date of admission and the date of the counselling interview, it is possible to measure these characteristics and for the Division of Counselling to advise the student of his chances of success in his chosen curriculum. If he is qualified for the curriculum he has selected, Counselling Service goes on to direct the student?s attention to those other curriculums which are in the same general area as the one he has chosen and which will also challenge his abilities and correspond to his interests, Through this counselling, the curriculums of the College of Mineral Industries, which are often less well known to high school students than others for which they are no more qualified by ability or interest, are brought to the attention of the incoming freshman.

Jan 1, 1959

By J. W. Rold

In 1973 housing and construction conflicts threatened Front Range gravel resources. The legislature addressed the problem by passing HB 1529, which required the Colorado Geological Survey to map the deposits and forbid local governments to change lands over commercial mineral deposits from zones allowing mineral development to zoning which conflicted with development. It charged counties to develop Master Plans for Extraction. Plans must consider resource quality, multiple-sequential-use potential, surrounding area compatibility, neighbors, quality of Life, extraction maximization and reclamation potential. Imprecisely worded statutes, budgetary constraints, lack of enforcement and political pressures have limited benefits from the law.

Jan 1, 1987

The absence of coal face particle management practices heavily penalizes coal transportation from initial loading to final consumption. Penalties include dust problems, significantly reduced mine loading cycle productivity, mine belt spillage, excessively high coal preparation costs and chute and dangerous pulverizer blockages at the final point of utilization. The common environmental and economic enemy is fines. Everyone knows that fines cause safety and environmental dust problems, but few understand that fines also swell broken coal to a point where 5 to 15 percent more time and capacity must be used to deliver the same tonnage. In this paper, methods and rewards for reducing and/or managing fines at the mine face are discussed. Computer-based loading cycle model productivity estimates, viewed from a new perspective, are made on the basis of material volume rather than on the long established and frequently misleading basis of tonnage. After all, it is typically the volume of broken material being transported that defines the capacity of a given transportation system, while the corresponding tonnages are merely a reflection of the specific material densities. Published evidence suggests that the swelling of broken coal can be decreased very significantly using small quantities of certain non-frothing chemicals added to mine face spray water and/or by employing improved mine face breakage practices. In a future paper, the effects on transportation productivity beyond the coal mine will be discussed.

Jan 1, 1994

By Anthony Harding, Rodolfo D. Aradas, Juan M. Fernandez, Darío Tsingas

"The adoption of tunneled combined sewerage interceptors and outfalls leads to design linings which are often subject to internal pressures that are larger than the external pressures, resulting in significant tension loads. The need to meet stringent durability conditions for the normal design life of 100 years often drives client specifications to require a double pass solution with a cast in situ secondary concrete lining. However, improvements in concrete technology and the need to seek efficiency in terms of time and costs, have driven designers to consider single pass segmental linings. The Riachuelo Sanitation project in Buenos Aires is subject to these constraints both upstream and downstream of a sewage treatment plant. This paper describes how the challenges of up to 2 bar pressure differential have been addressed by careful analysis of soil structure interaction to ensure that the full benefit of external ground pressure is realized, resulting in a more optimal design for the constructor both in terms of cost and time. INTRODUCTION The construction of long sewerage interceptors and outfalls is becoming an increasingly common piece of infrastructure for modern urban cities facing a large water front and estuarine conditions, which are under a significant environmental burden imposed by decades of sustained growth. Such works intercept most of the distributed sewage discharges to then divert them to a central treatment point from which it will be finally diffused via an outfall into a water body capable to accept these discharges under acceptable environmental conditions. Depending on the magnitude of the sewage load to be handled, the configuration of the urban environment and the conditions of the receiving water body, both in terms of oceanography forces and seabed conditions, these schemes will vary in length, conveyance capacity and design and construction requirements. When conditions permit, the current trend is the execution of long outfalls using flexible solutions (such as the use of HDPE pipes) which usually require some form of concrete ballasted weights to resist off shore dynamic forces when directly laid over the sea bed. However, this concept faces limitations when the conveyance requirements indicate the need for large diameters (typically above 3000 m) and also when the outfall needs to avoid deep features off shore such as navigation channels. When this occurs, tunneling, particularly segmentally lined tunnel constructed by TBM emerges as the most feasible approach for large diameter, long deep outfalls. The operating conditions often result in internal pressures that are larger than the external pressures, resulting in significant tension loads in the lining. The need to meet stringent durability conditions for the normal design life of 100 years often drives client specifications to require a double pass solution with a cast in situ secondary concrete lining."

Jan 1, 2016

By A. English, Edward Martinez, L. A. Haas, N. W. Johnson, Harrison Copper, M. E. Tawil, C. C. Harris, G. V. Jergensen, D. Halbe, M. P. Amsden

Declining US ore grades along with skyrocketing energy, materials, labor, and regulatory costs underscored the urgency for technological innovation in the mineral processing area. Re¬liance on the scale-up and automation of unit operations was the sector's primary battle plan. Debate continues on the upper size limit of concentrating plants and whether process controls should be centralized or distributed in the mill. In the materials handling area, the economics of large-scale and mobile systems, particularly conveyors, were well documented in the literature. Comminution, the most costly and energy consuming area of the processing flowsheet, saw improvements in process controls and liner designs. The trend toward larger grinding units stalled somewhat during the year owing to some operational problems at commercial plants. Research and development of apparently less expensive physical separation processes-that also boast recovery of cleaner and more environmentally acceptable products -gained momentum during the year. Because of escalating capital cost requirements for new plant capacity, the year saw a greater interest by mill designers to re-examine existing capacity. The focus here is clearly to modify or retrofit unit operations with more efficient components as an alternative to installing more costly new equipment. The problems facing the processing sector during the 1970s can be expected to continue in the decade ahead. Technological gains from scale-up and process controls appear

Jan 5, 1980

By A. C. Lyons, A. J. Reed

INTRODUCTION A trend which is obvious in the United Kingdom and is thought to be evident in other parts of the Western world is the disproportionate rise in the cost of tunnel mining labour compared with other tunnel cost increases. This disproportionate increase in labour costs has been accompanied by, and may be the result of, a shortage of skilled working labour. To combat this problem there has been a steady increase in the use of machines for excavation and for the erection of tunnel linings to keep the amount of skilled labour working below ground to a minimum. The typical tunnelling cycle, where the ground needs continuous support can be excavation, temporary support, temporary lining, grouting and permanent lining. It is obviously an advantage to combine as many of these operations as possible and carry out as much as possible by machine. Machines have been developed which will, either alone or used in combination with a shield, excavate and, when necessary, temporarily support the excavation. If a segmental lining is used, it can be so designed that it will form the permanent lining and reduce the cycle time and skilled labour requirement to a minimum. In cases in which the ground can be cut accurately to a smooth profile and will stand without support for a sufficient time, the lining can be expanded against the ground and the necessity of grouting eliminated. In cases in which ground will not stand without support, the usual method is to use a bolted lining and to grout behind it preferably as the shield is shoved forward. Whichever technique is used (this is largely determined by the ground) it is an advantage to make the segments as large

Jan 1, 1974

By J. A. Bowersmith

The environment in which the surface mining industry operates today is considerably different than that of a few years ago. Increased pressure from the public, government, labor and internal industry factors calling for the fulfillment of rapidly changing expectations is especially intense in the surface coal mining industry. Such things as requirements for increased production, the Mine Health and Safety Act, environmental concerns and land reclamation, shortages of qualified and enthusiastic employees and market cycles coupled with price competition are but some of the specific items that are requiring the surface mining industry to better utilize equipment, materials, and labor resources available, There is one technical tool available which will assist management to increase productivity, improve cost control and assist in planning, organizing and operating surface mines. Industrial Engineering is that tool. Before a discussion of specific applications of Industrial Engineering to surface mining is conducted, it is worthwhile to review a definition of Industrial Engineering and the history of its development. The following definition has been adopted by the American Institute of Industrial Engineers: "Industrial Engineering is concerned with the design, improvement and installation of integrated systems of men, materials and equipment. It draws upon specialized know- ledge and skill in the mathematical, physical and social sciences, together with the principles and methods of engineering analysis and design, to specify, predict and evaluate the results to be obtained from such systems."

Jan 1, 1976

The public relations problems of users of explosives have greatly increased within the past few years. One reason is that explosives and blasting agents are being consumed in increasing quantities. The principal reason, however, is that more people have become physically affected by blasting. Mines, quarries, and construction sites that were formerly in relatively remote locations now find themselves near congested areas. New express traffic ways being constructed to connect the suburbs with downtown areas are being built through the middle of long-established business and residential neighborhoods. The public becomes aware of blasting by two physical sensations-vibration and noise. Vibrations are usually so slight as to be negligible, and in most cases the only sensation noted is noise. The reduction of vibrations to this low level has been primarily achieved by the use of blasting practices and explosive products recommended by vibration engineers based on seismograph recordings. Unfortunately, very little scientific attention was given to the accompanying physical sensation-noise.

Jan 1, 1962