Search Documents

By Daniel R. Hack

Spatial relationships among physical 'and chemical properties pertinent to economic development of sand and gravel deposits have been little studied. Models need to address trends or zonation of material properties applicable to mine evaluation and planning or as a guide among deposits for use in regional assessment Models can then be utilized to design sampling programs to optimize additional data acquisition. Development of a preliminary methodology in the lower Boise River Valley, western Idaho, will utilize historical and recent data from a terrace-gravel deposit. Classical statistics and techniques of spatial data analysis will be evaluated as a precursor to formal geostatistical evaluation.

Jan 1, 2002

By B. Moudgil, Hassen El-Shall

Particle shape and size distributions are among the most important parameters that affect the filtration efficiency of phosphogypsum in wet- process phosphoric acid production. Cost-effective enhancement in filtration rate is desired by phosphoric acid producers for higher plant capacity and lower operating costs. In this regard, numerous research efforts have been carried out in different laboratories as well as in pilot and plant testing. Nevertheless, changes in phosphogypsum crystal shape and size distribution deserve special attention. In this study, the results obtained in the presence of Crysmod and Hiflo-S5 surfactants are discussed. The influence of such additives on crystal morphology and size distribution are studied under different sulfate contents (supersaturation). The obtained data are correlated with process efficiency parameters such as filtration rate, digestion of rock, and recovery of phosphate values. Up to 60% increase in filtration rate is obtained. In addition, an increase in digestion efficiency and P205 recovery is achieved due to addition of surface active agents. The observed beneficial effects are explained in the light of the changes induced in crystal habit, size, and size distribution.

Jan 1, 1999

By Fernando Concha, Arturo Barrientos

The flow in a hydrocyclone is divided into a boundary layer around the walls, an exterior inviscid flow and an air core in the center of the equipment. The boundary layer flow over the lateral walls is associated with the short circuit of particles to the underflow, while the boundary layer over the top of the hydrocyclone and the outer part of the vortex finder tube is related to the short circuit of particles to the overflow. Classification takes place in the exterior flow. The model can be validated with pilot or industrial data and simulates the performance of hydrocyclones in a wide range of design and operating variables.

Jan 1, 1992

By Zvonimir Jam?ek

In Rudarski Institut Ljubljana (RIL), i.e. Ljubljana Mining Institute, we have developed CADRIL, a smaller CAD package which purpose is to overcome the difficulties by introducing Computer Aided Design in our mines. Program CADRIL is a graphics shell for several computer applications in mining. With the basic version of CADRIL all 2D working maps for daily use can be produced. Inserting different program blocks into CADRIL we get versions MAPRIL, TAHRIL, SECRIL and so on. The main purpose of all versions is graphics design. The main and most innovative feature of CADRIL is the screen four-word command menu. Not having pull-down or tablet menus is the speciality of this program. CADRIL contains 500 achievable commands. Each of them can be composed by choosing two to four expressions stored and shown in a specific four- column menu, sorted as objects functions, parameters and modes. Thus all commands are immediately accessible. As a result of its plainness and adaptability to the present working methods of mining engineers, CADRIL quickly attained a good reputation in our mines.

Jan 1, 1992

By Thomas Van Riper

Newmont Mining Corporation started as one man's investment vehicle. William Boyce Thompson, Newmont's founder, was already a millionaire many times when he incorporated his existing Newmont company in Delaware in 1921. The initial stake in the company was $8 million in capital contributed by Thompson and several close associates. In its infancy the company was truly a holding company. It did not operate or manage any properties. This situation changed drastically over time. By 1939 Newmont was actively mining 12 gold mines in North America. The following year, the first copper mine that Newmont ever managed directly, came into full production in South Africa. The period after World War I1 was a glorious one for Newmont. Plato Malozemoff took the helm of the company, and expanded its operations over the next 30 years into copper in Arizona, oil and gas in the U.S. and the North Sea, into domestic coal and thankfully, into significant gold operations.

Jan 1, 1989

By Donald C. Wotring, Douglas A. Gabriel, Michael G. Vitale

"The Northeast Ohio Regional Sewer District (NEORSD) recently completed the 24-foot diameter Euclid Creek Tunnel using a steel-fiber reinforced concrete segmental lining. During construction HMM, the McNally/Kiewit JV, CSI/Hanson JV, and the NEORSD performed a test program to evaluate replacement of steel fiber with synthetic fiber. A section of synthetic-fiber-reinforced cast-in-situ lining was also placed as part of the permanent works for the starter and tail tunnels. Laboratory and field testing were performed on two complete segmental rings reinforced solely with synthetic fibers. This paper summarizes the testing program, construction, and results of the synthetic-fiber-reinforced CIP lining and concrete segments. INTRODUCTION The principal feature of the Euclid Creek Tunnel (ECT) project is a CSO storage tunnel that is one component of the Northeast Ohio Regional Sewer District’s (NEORSD) Easterly CSO storage and conveyance system. The tunnel, shafts, and appurtenant facilities will be used for the collection and storage of CSOs from the northeastern part of Cleveland, Ohio and subsequent conveyance to the NEORSD’s Easterly Wastewater Treatment Plant for treatment. The ECT project includes five drop shafts that extend as deep as 220 feet below the ground surface. The ECT alignment and shaft locations are shown in Figure 1. Traditionally in northeast Ohio, tunnel excavations were supported with a two-pass system using steel ribs and timber lagging, followed by cast-in-place concrete. Control of rock overbreak proved difficult with large-diameter two-pass operation, and invert degradation led to train derailments. To mitigate these risks, the ECT was supported using one-pass, precast, bolted, gasketed concrete segments reinforced with steel fiber alone. Tunneling operations were very successful and experienced no significant delays or claims. As a result of the positive ECT experience with steel fiber-reinforced segments, Hatch Mott MacDonald, LLC (HMM), McNally/Kiewit (MK) joint venture, CSI/Hanson (CSI/H) joint venture, and the NEORSD performed a test program to evaluate replacement of steel fibers with synthetic fibers in segmental rings. This paper presents the laboratory and field testing program, construction, and results of the synthetic-fiber-reinforced cast-in-place (CIP) lining and concrete segments."

Jan 1, 2016

By W. J. Schlitt, K. McNaughton

A heap-leach field test was conducted during the 1993-1994 winter season at Carmacks, Yukon Territory, Canada. The purpose of the test was to demonstrate the viability of heap leaching Carmacks oxide copper ore in an arctic setting on a year-round basis. The test itself utilized a 5-m-diam crib loaded with 250 t of composite ore from the Carmacks copper deposit. The ore was stacked to a total height of 7 m in the crib, including 1 m of ore as an over- layer above the emitter system. This matched the plan for the commercial heap at the time when the test was started. The design also replicated an interior segment of the commercial heap. Leaching was done at a flow rate of 0.2 L/min/m2 using leachate at 21 °C. This temperature was maintained with no external heat input other than normal process heat transferred from electrowinning to the leachate via solvent extraction. Winter conditions were quite typical of those expected at the mine site. The temperature reached -54°C, while averaging -13°C over a three-month period. In spite of some flow system problems, leaching continued unabated, and freezing was limited to the insulating ore over-layer and isolated points near the outer crib walls. Thus, the test demonstrated that year-round heap leaching of Carmacks copper ore is practical in an arctic setting.

Jan 1, 2000

By A. E. Isaacson, D. B. Dreisinger, G. A. Kordosky

The U.S. Bureau of Mines is researching the application of solvent extraction technology to highly acidic (pH < 1) copper leach liquors. As increasingly complex copper ores are mined for leaching, use of highly acidic leach solutions maybe necessary to effectively recover the contained metal values. A mixture of two commercially available extractants, based on aldoximes and substituted 8-hydroxyquinoline, which has a high transfer efficiency has been identified. A synthetic leach liquor, containing 5 g/L Cu at pH 0.9 was processed utilizing the mixed extractant and a laboratory SX circuit. The loaded organic was stripped with a synthetic barren electrolyte compatible with electrowinning technology.

Jan 1, 1993

By K. A. Natarajan, M. K. Yelloji Rao

The effect of galvanic interactions among sulfide minerals such as chalcopyrite, galena, and sphalerite in the presence and absence of a grinding ball material on the flotation recovery of chalcopyrite has been studied. X-ray photoelectron spectroscopy (ESCA) studies were carried out to identify the reaction products on the sulfide minerals after different apes of galvanic interactions. Galvanic contact with active minerals such as galena and sphalerite, either alone or together, significantly affected the floatability of chalcopyrite mineral, such an effect being more severely felt in the additional presence of a grinding medium as well as oxygen. Surface analysis studies revealed the presence of oxyhydroxide species of iron on all the sulfide mineral samples which were in prior contact with the grinding medium. The formation of such oxyhydroxide species of iron was found to be dependant on the relative electrochemical activity of the mineral. Probable electrochemical reaction mechanisms are discussed.

Jan 1, 1990

By Milton E. Wadsworth, Ximeng Zhu

Impurity metals can markedly influence the anodic dissolution of gold in the presence of cyanide. Several important findings related to the influence of lead are reviewed and some new observations presented. Based on the effect of pH, the scan direction, and voltage, it may be shown there are three separate voltage regimes where lead influences the anodic dissolution of gold. These are related to Pb°/ HPbO2, Au-Pb /HPbO2, and HPbO2/PbC2; oxidation-reduction reactions which provide low resistance paths for electron exchange. The gold dissolution rate was determined by direct solution analysis and is compared to the rate implied by electrochemical measurements.

Jan 1, 2005

By P. E. Snoek, R. L. Gandhi, C. S. Miller

Slurry operations are an integral part of mineral processing. There is therefore reason to consider using slurry pipelines for long distance mineral transportation. This paper reviews the current state-of-the art of such systems and, in particular, the design factors which must be addressed. It also discusses the selection of major components such as pipe, pumps, valves and storage facilities. Finally, the major steps required to determine the economic feasibility of a slurry system are listed and the major advantages and disadvantages of slurry pipelines compared with other forms of land transport are summarized. SLURRY PIPELINES: GENERAL OVERVIEW Minerals Transported Long distance slurry pipelines have been successfully used for transporting coal, iron concentrate, copper concentrate, limestone and phosphate. Additionally, several tailings disposal pipelines of considerable size and length have been built, but these generally are not categorized as long distance commercial mineral transportation systems. Table 1 lists selected examples of commercial slurry pipelines.

Jan 1, 1986

By J. F. Able, F. Djahanguiri

The US Bureau of Mines conducted research on underground stope leaching of metalliferous ores. Leaching underground would minimize the environmental impact of ore processing on the surface and would maximize minable reserves. An important aspect of this process is the minimization of pregnant solution losses and groundwater contamination by leach solutions. Bulkhead design and construction are important issues for solution control and stope-leaching economics. A reinforced-concrete bulkhead was designed, constructed and tested for solution control in an underground mine near Idaho Springs, CO. This paper presents the bulkhead-design methodology and construction procedure.

Jan 1, 1998

By Richard W. Hornung, Steven Samuels

A great amount of work in recent years has been devoted to refining older survivorship models, e.g. life tables, and developing newer ones, e.g. Cox regression. In this paper, these models are applied to data from an epidemiological study of uranium miners in four western states conducted by the U.S. Public Health Service. One of the principal problems addressed in this paper concerns the appropriateness of using cumulative dose as the measure of radiation exposure. An alternative is considered that incorporates dose rate into the model. This procedure does not implicity assume that equal cumulative doses produce the same lung cancer mortality, but instead considers the amount of time in which each miner&apos;s dose was accumulated. Results of the statistical analysis indicate that dose rate is a significant factor at higher cumulative dose levels, with lower dose rate apparently more damaging than higher dose rate. The shape of the dose response curve is curvilinear at higher dose levels. No interaction was found between smoking and radiation exposure on a multiplicative or relative scale.

Jan 1, 1981

By R. Fraher

The control of mine roof is of vital interest in underground coal mining not only for reasons of safety, but also to avoid the high costs of cleanup, resupport and production losses that can result from roof falls. The difficulty in determining roof stability mine-wide is due in large part to the broad variation of geologic and structural conditions that typically exist throughout a mining area. To ensure a stable roof over the entire mine, support systems must be selected to minimize the possibility of failure. The magnitude and cost of the support selected is a trade off against the cost of the number of falls that can still occur after it is installed. Because of the large number of variables involved in analyzing and optimizing roof stability versus support, a digital computer simulation was selected to find a cost effective solution to roof support design. A total cost approach is used which includes the actual cost of the roof support as well as the cost of the roof fall in terms of resupport and loss of production (Fraher 1990a). A Monte Carlo simulation program called ROCSIM (Roof control Optimization Cost SIMulation) has been developed for determining the optimum roof control system and design layout for underground room-and-pillar mining.

Jan 1, 1992

By W. G. Pariseau

Recent advances in rock-mass mechanics and computational technology now allow for the stability analysis of excavations in "wet" mines where mining-induced changes in rock mass deformation and fluid flow are coupled and time dependent. In addition to water pressure and flow in jointed, possibly porous, rock masses, all of the usual dry-mine parameters, including the premining stress state and rock-mass properties, are taken into account. Finite-element analyses of shafts and tunnels, as circular, elliptical, rectangular and arched-rectangular hole shapes excavated in an initially stressed and pressurized rock mass, indicate that the usual guidelines for optimum shape and orientation of single openings apply. Here, optimum means maximizing the minimum wall safety factor or, equivalently, minimizing the peak stress concentration. The results also show that failure originates in elements at the wall and the minimum safety factor at the wall in the wet case is always less than the dry case, regardless of drainage time allowed.

Jan 1, 1997

By Anthony G. Fonseca, W. W. Wen

About 45-50% of the coal mined in the U.S. passes through coal preparation plants; east of the Mississippi River this number increases to about 75-80%. Although the cost for coal preparation is worthwhile to some, the coal industry faces the challenges of continuing downward pressure on the price of coal and the impact of new environmental regulations. Coal preparation, as commercially practiced today, is an effective process achieving 75-803 ash reduction, 15-8m trace element reduction, and 85-90% Btu recovery; it is less effective for pyrite reduction (35-70%), and on-line operating time (40-60%), and suffers from obsolete control systems. Methods will be discussed for reducing costs of coal preparation and improving the performance of coal preparation plants. Comments are included on equipment selection, especially for -28 mesh coal, and prep plant operation and control practices. Btu recovery, ash and pyrite reduction, fines processing including dewatering and slurry fuel use options are emphasized. Trace element removal and expert control systems for maximization of prep plant operation also will be highlighted.

Jan 1, 1995

By J. A. Organiscak

Two types of airflow splitting methods for improving longwall dust control were investigated by the National Institute for Occupational Safety and Health&apos;s Pittsburgh Research Laboratory. Investigated were a translucent mesh barrier and a staged spray barrier system to confine the shearer-generated dust to the coal-extraction side of the longwall face while maintaining a cleaner split of airflow on the opposing worker walkway side of the longwall face. In laboratory experiments and in a longwall field evaluation, the translucent mesh barrier was shown to provide notable dust-control effectiveness for a distance of up to 60 m downstream of the shearer, provided that the mesh barrier remained relatively parallel to the airflow. The staged spray barrier system showed marginal dust-control effectiveness in the laboratory and, therefore, was not field tested.

Jan 1, 2000

By Gerrit V. R. Goodman, Fred N. Kissell

The issue of miner safety in case of an underground mine fire has been extensively examined by both government and industry. These efforts have intensified in recent years following a number of fatal fires at underground coal mines. As a result, there is an increasing interest in the reliability of coal mine escapeways during a mine fire. This paper discusses the use of fault tree analysis for evaluating escapeway reliability. A fault tree is developed using standard logic formulations. It is later evaluated using commercially available software. The computer model uses Boolean reduction to obtain the minimal cut sets and minimal path sets of the tree. A brief analysis is also conducted to determine the occurrence probability of the TOP event. This study shows that fault tree analysis is a viable means of analyzing escapeway reliability. The cut and path sets reveal those event sequences leading to fatalities. Such information is useful in safety training and accident prevention. The probability of the TOP event shows the frequency of occurrence for fatalities in an underground mine fire. The usefulness of this value, however, is limited by the accuracy of the data for the initiating events. For mining events, the data is difficult to estimate precisely.

Jan 1, 1989

By Mortimer J. Richardson

In the context of this session on "Practical Placer Mining," a projection of the present into the future first assumes that there is a future for Placers. The second assumption is that there is the combination of adequate reserves and a willing, mining investment source to finance placers. This paper will point out the opportunities on both assumptions, illustrating my positive position on the future of gold placers. In order to focus this paper more effectively, I have chosen GOLD as the subject mineral. However, it is recognized that much of the technology for exploring and mining gold placers has been applied to other alluvial deposits; including platinum, diamond, tin, and various industrial minerals (which are often referred to as "placers" though this contradicts historical definitions). Over the past 10 years I have presented several papers on the general subject of placers, most of which are listed under References. These have included topics such as exploration, evaluation, small-scale gold placer mining and decision-making, mining and processing equipment designs, and dredge-mining operations. In an attempt to identify the more promising, undeveloped placer potentials in the world I have usually mentioned the USSR and China but qualified them as being either inaccessible, or, politically difficult to obtain. However, with recent developments in the USSR, the obstacles appear to be somewhat diminished.

Jan 1, 1992

By L. Vandamme, J. H. Curran

A fully three-dimensional hydraulic fracture propagation model, based on the Displacement Discontinuity Technique, is briefly described. Using this model, it is shown that the geometry of a propagating fracture is dependent on several factors, among which the fluid pressure distribution within the fracture plays an important role. The containment of hydraulic fractures is found to be dependent on stress and toughness barriers in the formation. Containment is also observed to be more effective with a decrease of the viscosity, pressure or flow rate of the injected fluid. The three-dimensional layout of the fracture is shown to have a definite influence on the width and pressure distributions within the fracture. The examples considered indicate the need for fully three-dimensional models, as complements to the commonly used two-dimensional and pseudo-three-dimensional models.

Jan 1, 1986