Search Documents

By Ole Bernt Lile

The well-known method of C. Schlumberger, Mise a la masse, has become a popular method again in ore exploration in Norway after many years of dominance by EM methods. The principle of the method is to place a current electrode within a conducting ore body and remove the other electrode to a great distance. (Figure 1). Often it is convenient to place a return electrode on each side of the area explored. The method is best suited for ores that have a conductivity contrast, relative to the host rock, of several orders of magnitude. The potential drop within the ore itself may then be neglected and the ore contact against the rock may be regarded as an equipotential surface. One may say that the ore body is electrically charged. Therefore, in Norway the method is now most often called the Charged Potential Method (abbreviated CP). The most usual way to present data obtained by CP, is to draw equipotential lines based on potential values measured in profiles on the surface. Such a potential map gives an immediate picture of the outcrop of the ore and also indicates disturbing conductors in the neighborhood. It may also be useful to look at the potential profile and its horizontal gradient along the strike axis of the potential map. These profiles may give information about the strike length of the conductor. Figure 2 shows the theoretical profiles of potential and gradient along the axis of the potential picture on the surface over a charged line plunging 15 degrees. It may be seen that the maximum of the gradient curve clearly indicates the lower end of the conductor. Figure 3 shows the corresponding pro- files over a charged line plunging 45 degrees. In this case, it is not possible to see an indication on the curve of the lower end. Only curve fitting could help interpretation in this case.

Jan 1, 1975

By A. Wahab Khair

There are a number of factors, including mine geometry, local geology, geotechnical properties of overburden materials, surface topography, sequence of overburden strata, and extraction rate, affecting characteristics of surface subsidence imposed by large underground excavation. Among the factors, the first three have the major impact on magnitude and area of influence of final subsidence. Hence, a model has been developed, considering mine geometry and geologic and geotechnical properties of the associated area, to predict maximum possible subsidence and subsidence profile at any cross-section within the subsidence influence zone. Based on extensive field measurements and mechanics of strata behavior, under the action of overburden pressure in the vicinity of the large underground excavation, the vertical plane of influence zone has been divided into five areas: 1) excavated, 2) caved, 3) fractured, 4) highly deformed but continuous, and 5) subsided zones. In the final state of subsidence each area maintains a certain volume expansion/contraction, i.e. a factor which depends on geologic, geotechnical properties of overburden strata and state of stress within the subsidence trough. The cumulative volume expansion and contraction partially compensates for the extracted volume and the difference between the two is reflected as the subsided area in the form of the area within a curve defined by a probability function. The input parameters for the model are mine geometry (i.e. length and width of the panel), depth of cover, and geologic and geotechnical properties of overburden strata (i.e. percentage of hardrock, sandstone and limestone, and soft rock, shale within the overburden strata and Rock Quality Designation). The model calculates angle of draw for the site, expansion factor for each zone utilizing empirical relationships, maximum possible subsidence and plots the subsidence profile curve. The model is developed for a longwall excavation with unique characteristics of prediction of angle of draw and maximum possible subsidence for a given geologic and mining condition at any cross-section within the influence zone of subsidence.

Jan 1, 1986

By David A. Grisafe

Divided opinions concerning dredging-permit locations and boating uses on the Kansas River in northeastern Kansas led to a study of the recreation potential on the river by a legislatively mandated interagency group (five agencies) that included the Kansas Geological Survey (KGS). In addition, the KGS conducted its own study of the river corridor, encompassing the development, geology, and economic resources of the corridor (Brady and others, 1998). The corridor area is 12 mi wide and 140 mi long (171 river miles). Included in the study was the potential impact of restric¬tions to river dredging. The Kansas River and its floodplain in northeastern Kansas are underlain by Lower Permian and Upper Pennsylvanian limestones and shales. The river and its floodplain are the major sources of sand and gravel for northeastern Kansas, and the limestones along the river bluffs supply crushed stone and building stone. The population of the 10-county area bordering the river has grown by 20% since 1980, and now comprises nearly 40% of the state's population (U.S. Bureau of the Census, 1996). Projections (Floerchinger, 1992) indicate close to 50% of the Kansas population will reside in these counties by 2025, with a continued increase in the demand for aggregates. Factors such as floodplain width, price and availability of land, and overburden ratios tend to favor river dredging on the lower part of the river, and floodplain or pit dredging on the upper portion. The use of alternate sources of sand and gravel such as the Missouri and Arkansas Rivers would increase sand prices due to transportation costs to much of the 10-county area. In 1996, river and pit dredges along the Kansas River supplied more than 3 million tons of sand and gravel valued at about $8 million to northeastern Kansas. As a result of its study, the KGS had concerns with the idea of large recreation zones on the river that excluded river dredging in areas of presently large population and projected population growth. This controversial issue is likely to recur elsewhere.

Jan 1, 1999

By Robert Marks, Enrico Dal Negro, Richard Schulkins

"In July 2012 construction started on the Grosvenor project, a five million tonne per annum underground longwall mine planned for Moranbah in Central Queensland. Grosvenor is located immediately to the south of the existing Moranbah North mine which has been in operation since 1998. EPBM technology is being used for the first time in Australia for excavation of a coal drift. The TBM was used to build two drifts on the project, one for the coal conveyor which will transport to surface, and another for people and equipment to access the underground once the mine’s operational (as shown in figure 1). The TBM will pass beneath a steel archway roof that has been installed at the drift’s entrance and begin drilling into the ground to build the seven metre diameter tunnel, descending at an angle of one in eight until it reaches the depth of the coal seam approximately 160 metres below.INTRODUCTION AND BACKGROUND The first TBM used in a coal mine was in 1962, a Wohlmyer, in Westerholt, Germany. A further 75 km of tunnels were excavated in coalmines within Germany between 1971 to 1983. This paper will review the Grosvenor Mine project (Grosvenor) owned by Anglo American Metallurgical Coal (Met Coal) includes the construction of a new underground coal mine and surface facilities on the northern boundary of the town of Moranbah in the Central Queensland Bowen Basin coal precinct. The contract to undertake the underground development works was awarded to Redpath in 2012. The scope of the Grosvenor Project was to construct temporary office and workshop facilities, install 2 portal arches, backfill boxcuts and infrastructure, excavate by EPBM method 967 m of 1:6 gradient Conveyor Drift and 1,258 m of 1:8 gradient Transport Drift, development of 2,520 m of pit bottom area roadways and development of 10,550 m of the first longwall tailgate. In the following figures 2 and 3, is possible to see the aerial view of the job-site."

Jan 1, 2016

By John Marshall

Silverton was the queen city of the western mining towns in the early 1900s. Located high in the San Juan Mountains, the town constantly grew and changed. Yet, it was subject to the vagaries and whims of economics, politics and disasters, natural or otherwise. Breweries, smelters and sawmills serviced Silverton's swelling mining population, which reached several thousand at its peak. Two trains a day ran from Durango to Silverton, in addition to trains running from Silverton over the top of Red Mountain on to Ironton. They ran up Cement Creek to the little town of Gladstone and up the Animas River Valley to Howardsville, Eureka and Animas Forks. During these prosperous times, construction flourished. There were plenty of wooden structures, and many of these stand today. The first brick buildings were built by bricklayer Patrick Stanley in 1877. It took quite a while for the first car to arrive. Almost 28 years passed from the coming of the first train to the arrival of the first car. It was brought over 3,840-m (12,600-ft) Stony Pass from Creede, CO, in an incredible journey retold years later by Louis Wyman. "Dad's daydreams were not the idle musings or the fantasies of a mystic," Wyman said. "They had a way of erupting into reality. He advocated and built good roads," he said. "During the summer of 1910, he was up to his sweatband in a project that took in half the state of Colorado. He envisioned an automobile highway, unheard of at that time, running southwest from Denver through the scenic grandeur of the high Colorado Rockies. The road would traverse a thousand miles or more of the state's finest recreational land finally circling back to Denver. Years later, when all of the county roads had been connected, it became known as 'Colorado's Thousand-Mile Circle Route.' Of course, Silverton and the San Juans were bright stars along the way."

Jan 1, 1997

By Barnaby J. Watten, Sibrell. Philip L., Brian J. Vinci, Andrew E. Friedrich

We evaluated a new process for remediation of acid rock drainage (ARD). The process treats ARD with intermittently fluidized beds of granular limestone maintained within a continuous flow reactor pressurized with CO2. Tests were performed over a thirty day period at the Toby Creek mine drainage treatment plant, Elk County, Pennsylvania in cooperation with the Pennsylvania Department of Environmental Protection. Equipment performance was established at operating pressures of 0,34,82, and 117 kPa using an ARD flow of 227 L/min. The ARD had the following characteristics: pH, 3.1; temperature, 10 OC; dissolved oxygen, 6.4 mg/L; acidity, 260 mg/5; total iron, 21 mg/L; aluminum, 22 mg/L; manganese, 7.5 mg/L; and conductivity, 1400 uS/cm. In all cases tested, processed ARD was net alkaline with mean pH and alkalinities of 6.7 and 59 mg/L at a CO2 pressure of 0 kPa, 6.6 and 158 mg/L at 34 kPa, 7.4 and 240 mg/L at 82 kPa, and 7.4 and 290 mg/L at 117 kPa Processed ARD alkalinities were correlated to the settled bed depth (p<0.001) and CO2 pressure (p<0.001). Iron, aluminum, and manganese removal efficiencies of 96%, 99%, and 5%, respectively, were achieved with filtration following treatment. No indications of metal hydroxide precipitation or armoring of the limestone were observed. The surplus alkalinity established at 82 kPa was successful in treating an equivalent of 1136 L/min (fivefold dilution) of the combined three ARD streams entering the Toby Creek Plant. This side-stream capability provides savings in treatment unit scale as well as flexibility in treatment effect. The capability of the system to handle higher influent acidity was tested by elevating the acidity to 5000 mg/L with sulfuric acid. Net alkaline effluent was produced, indicating applicability of the process to highly acidic ARD.

Jan 1, 2000

By Andrew Burton, Damian Schofield, Jeremy Noond

This paper will introduce and discuss a range of techniques that utilise new developments in Computer Graphics (CG) and Virtual Reality (VR) for the investigation of incidents and accidents in mining environments. The future of mining safety may not be totally led by the demands of the mine operators, but sometimes by the academics, commercial software developers and legal pioneers who generate new ideas and products and set admissibility precedents which may change the way certain traditional investigative operations are performed. In any accident investigation the outcome from the investigating team is often a complex affair and the results of the investigation are often reported in large, convoluted documents. Computer-generated forensic reconstructions allow investigators to present accident scenarios in an accessible and easily understood, visual manner. Surveys in the US have also shown that people have increased recall of computer-generated images over many other forms of evidence. The AIMS Research Unit in the UK have been pioneering the use of Computer Graphics (CG) and Virtual Reality (VR) technology for both industrial and road traffic accident reconstruction. This paper and accompanying presentation will contain examples of forensic reconstructions developed by the authors that explain some of the methodologies used to ensure admissibility of this type of digital evidence. The paper will contain a number of case studies based on UK and International industrial accidents. The paper will focus on how AIMS Research is extending the capabilities of the accident reconstructions created to take advantage of the latest developments in VR technology. As digital technology makes its impact within professional and commercial fields, computer generated forensic reconstructions will form important admissible evidence in the courtrooms of the future. The technology will also make a great impact in the way we train our workforces, with highly visual three-dimensional (3D) interactive training tools becoming the norm. Acceptance by the public, courts and workforce is an important issue, and implementation strategies must be considered carefully.

Jan 1, 2002

By B. Ollila, L. Brown

As mining fronts converge in sill pillar extraction, the mine seismic hazard can be significantly altered and large seismic events have been known to occur. This study used common seismological tools to analyze the extraction of highly stressed sills from two deep Canadian mines with the objective of characterizing the rock mass failure process and relation to large seismic events. The approach treated a sill pillar as a mine-scale failure process, meaning the temporal and spatial analysis scales needed to exist on a similar scale to a significant part of the mine. The temporal analysis scale overlapped with the entire mining sequence, included several years of data to establish long term change in the characteristics of rock mass failure. The spatial analysis scale included the rock mass surrounding a large part of the convergent mining sequence. To accommodate the large spatial and temporal scales, the highest magnitude 2% of events in the dataset were analyzed. Similar results were shown for sill pillars in both mines. Changes in event location, time, magnitude, energy index and apparent volume were similar to expected behavior of rock failure. Indications of strain hardening and strain softening were observed in the sills. The hardening period was characterized by a high rate of small events, high energy index and low apparent volume, giving an indication of high stress and low rock yield. The softening phase was characterized by a decrease in the rate of small events concurrent with an increase in the rate of large events, low energy index and high apparent volume, indicative of release of stress and increase in deformation. Large magnitude seismicity was strongly related to the softening phase, with several Nuttli magnitude 3.0+ events occurring shortly after the transition from hardening to softening failure regimes. Sill failure was indicated by consistently low EI and low levels of seismicity and seismic hazard in the sill pillar.

Apr 26, 2022

By Julius Rubinstein, Victor Badenicov

The development of column flotation is the most significant achievement in the area of mineral processing in the last few decades. The high efficiency of column flotation allows a reduction in process time, a decrease in the number of cleaner stages and in the volume of the circulating load in the flotation circuit, and, as a result of this, an increase in consistency and reliability of operations. Unique multisectional column flotation apparatuses were developed. Such designs have a number of essential advantages as compared to monocells. A change from monocells to multisectional column allows to provide favourable conditions for separation of particles of various floatability. To attain that aim particular hydrodynamics and aeration regime is established in each section of the column, operational variables being adjusted according to the floatability of the material. Therefore in multisectional column machines the material-apparatus feedback can be established, process variables optimized depending on the characteristics of the floated materials. This concept forms the basis of column designs we have developed. For the first time column cell with alternating slurry Rows (combination of co- and counter-current flows) were developed and commercialized . Successful operation was reported of the new generation of columns with cell volumes of 10 to 80 m3 and the height of 4-6 m in copper, molybdenum, antimony, tungsten and nickel ores and coal slurry processing at different plants. Operation experience of these cells showed their considerable design and operational advantages and verified the proposed options and relationships. The new apparatus is provided with a pneumohydraulic aerator allowing to control bubble size distribution, the service life of the aerator is not less than two years. A multilevel flotation model was developed and used to work out a technique of column design and process parameters calculation. A method of the apparatus design parameters calculation based on laboratory test results (scaling up) was worked out. The method is based on flotation macro and micro-hydrodynamics simulation.

Jan 1, 1995

By Jerome C. Motz

Los tipos, tamaños y número de trituradores empleados en un sistema completo de reducción varían con factores tales como: el volumen de mineral que debe ser procesado, tamaño de la mina, tamaño máximo del todo-uno, dureza del mineral y de su roca soporte y tamano requerido para el producto final. Básicamente, sólo existen tres tipos distintos de equipos de trituración para la etapa primaria. Estos son: machacadoras de mandíbulas, trituradores giratorios y molinos de impactos, y cada uno tiene unas características operativas propias. Las trituradoras de mandíbulas operan por aplastamiento de las rocas entre dos paredes, una fija y otra móvil, en una cavidad determinada. Han sido ensayadas variaciones en la caída y movimiento, pero la mayoría de las máquinas del tipo Blake tienen un ángulo de trituración de aproximadamente 27° entre las mandíbulas fijas y móviles. El principio de trabajo del triturador giratorio es muy simple. Si un cono es montado en un eje vertical y la parte superior del eje se sitúa estacionaria mientras que la parte inferior gira excéntricamente, el cono tendrá también un movimiento excéntrico. Si el cono se coloca en una carcasa conveniente se movers aproximándose y retrocediendo de las paredes que lo contienen a la vez que gira. Si el cono y las paredes de la carcasa son suficientemente robustas y pesadas, cualquier cosa apresada entre ellas será triturada. Al lado de los incrementos de la eficacia desarrollados por las continuas acciones de trituración y el curvado de las caras de trituración, los trituradores del tipo giratorio tienen las siguientes ventajas: 1. La gran abertura de alimentación disponibles en comparación con trituradores de otro tipo. 2. El alto rango de tamaños y capacidades, que se encuentran entre 600 y 6.000 toneladas por hora. 3. Generalmente no es necesario control en la alimentación. Dumpers de 150 a 200 toneladas descargan directamente en las actuales instalaciones.

Jan 1, 1982

By Yoshio Hiramatsu

In Toyoha mine near Sapporo, the ground temperature is very high, perhaps due to inflow of hot mineral water, the origin of which may be rock masses intruded by the igneous activity in the Tertiary period. The rock masses are found about 2 km east of the mine, their temperature being estimated at from 770 to 870 K at a depth of 3 km. In this mine several veins bearing zinc and lead ores have been mined down to the depth of 300 m from the level of the main entry, of which altitude is 551 m above the sea level. Formerly no attempt was made at development of the deeper part of the mine than the 350 m level from the main entry. Let us indicate hereafter the levels in this mine in such a way that the level 300 m deep from the main entry is denoted as 300 mL. Since 1974, however, the 450 mL of Tajima vein has been developed by deepening No. 5 Shaft to, and by driving drifts in the level. Much hot mineral water has been flowing into the drifts from rock. After twenty-eight months from the beginning of development, the total length of excavation amounted to about 1300 m. The success in development so far may be attributed to cooling rock and air with chilled water and to adopting heat-resisting explosives and detonators. This cooling costed very much and for further development in this level a more effective and economical cooling is desired if possible. To obtain fundamental data for designing an economical cooling, the authors investigated, as a preliminary study, the heat balance in the main drift of 450 mL, by measuring the temperatures of air, rock, hot mineral water, the rates of flow of air and water and so on, in August 1976. They are now carrying out continual measurements of the variations in rock temperature, air temperature and humidity with time. The present paper describes the details of the preliminary study.

Jan 1, 1980

By M. Kung, D. Schwegler-Berry, V. Castranova, D. Lewis, H. Abrons

Pulmonary responses to coal mine dust exposure were investigated by analysis of bronchoalveolar lavage specimens from non-smoking coal miners (n-12, mean age-43 ± 2 years, mean underground exposure-17 ± 2 years) and from non-smoking normal volunteers (n-18, mean age-43 ± 2 years). Spirometric and diffusion capacity indices were monitored as part of a physical exam. Lavage was performed in a subsegment of the right middle lobe by instillation of 200 ml of warmed saline solution in 50 ml aliquots and recovery by gentle suction. Specimens were centrifuged at 500g for 5 minutes at 2°C. Total and differential cell counts were recorded. Secretion of oxidants measured by chemiluminescence, surface morphology (spreading and ruffling), and lymphocyte parameters were determined. Lavage fluid was analyzed for the presence and quantity of acute phase reactants and immunoglobulins. Pulmonary function measurements as well as recovered lavage volume, total lavagable cells, and differential cell counts were similar in both miners and controls. Both resting and phorbol myristate acetate-stimulated chemiluminescence were also similar in miners and controls. In contrast, particle-stimulated chemiluminescence was significantly decreased in the alveolar macrophages from the miners (48% of control values). Morphometric analysis of scanning electron micrographs indicate that phagocyte surface spreading was similar in miners and controls. However, surface ruffling was 127% greater in the miners compared to controls. Lymphocyte subpopulations were similar in miners and controls. Protein analysis of the lavage fluid revealed lower total protein content in the lavage fluid of miners. However, the concentration of albumin, IgG, and IgA were similar in miners and controls. We conclude that most indices were normal in underground miners working under the current dust standard of 2 mg/m3. The decrease in particlestimulated chemiluminescence and the increase in surface ruffling in miners may suggest the beginnings of particle overload and activation of the macrophages. In addition, a decrease in total protein was noted in lavage fluid from miners.

Jan 1, 1991

By Steven L. Webb

In 1965, Monsanto started planning of a new dike (No. 15) for use in disposing of ore tailings at its Columbia, Tennessee phosphorus plant. Generally, in the phosphorus industry only clay tailings are produced making it necessary to borrow fill for construction of a retaining dike. Borrow area investigations indicated that weathered shales and limestones adjacent to the dam site would provide adequate construction materials. It was proposed that the more clayey weathered shales would be used for the impervious core and the more granular weathered limestones would be placed in the outer shell of the dike. A dike section is shown in Figure 1 with gradation curves for core and shell materials in Figure 2. Figure 3 shows an aerial view of the tailings pond and dike during first-stage construction. Although the borrow area explorations indicated that the weathering of the sedimen-tary deposits was highly irregular, it was not considered necessary, at the time, to specify special excavation techniques that would ensure a thorough blending of the materials in the borrow pit. Instead, because of the short haul distance, a scraper operation for both clay core and granular shell materials was adopted as the most economical construction method. Using this materials-handling technique, variations in permeability could be expected in the compacted layers inthe embankment. Where continuous layers of less clayey limestones were placed in the core of the dam, extending from the upstream to downstream shells, seepage losses would be expected to increase substantially. Upon completion of the damn 1966, and shortly after reservoir filling, it was apparent that the construction technique used had resulted in the formation of pervious layers through the clay core. Excessive seepage on the downstream face of the dike was noticeable within a very short time. A monitoring program was established, using piezometric observations and flow measurements. These data indicated that seepage should be reduced and the application of an asphaltic emulsion

Jan 1, 1971

By Fikret Suner

Two rare evaporite minerals, nahcolite (NaHC03) and trona (Na2C03?NaHC03?2H20), are both widely used in the production of sodium carbonate (Na2CO3) The largest natural carbonate deposits (trona) are in Wyoming, USA, the second largest deposits are in Turkey, in a lacustrine basin (Beypazari) where nahcolite and trona are located within the Miocene Hirka Formation. The Hirka Formation is mainly composed of bituminous shale, claystone, marlstone, tuffltuffite, and dolomitic limestones. Although numerous trona beds are interbedded within the above mentioned sedimentary units, there are only two beds of trona that are of economic interest. The lower part of the lower trona bed is rich in double carbonates such as pirrsonite (NA2C03? CaC03?2H20) and gaylussite (Na2C03?CaC03?5H20), indicating a change in Ca/Na ratio in the solutions which are responsible for the formation of soda occurrences. In contrast, the upper part of the upper trona bed is rich in nahcolite. This minerological pattern has been found in every drill- hole in the basin. While both trona beds average up to 10 m (33 ft) thick, the average thickness of nahcolite is approximately 0.5 m (1.6 ft). Also, thin section studies show that many fibrous and lath-like trona crystals contain small radial nahcolite crystals; all of them are euhedral and equi-dimensional. Geochemical studies of major, minor, and trace element contents also support this coexistence. Macroscopic and microscopic observations reveal that the nahcolites principally were formed as a result of an incongruent dissolution process of trona. In conclusion, the presence of nahcolite in the Beypazari basin is due to the dissolution process of trona, particularly during the last stage of evaporation, as a result of fresh water entering the basin. During that time, an increase in the HC03/ C03 ratio resulted in nahcolite-trona phase transitions.

Jan 1, 2001

By Donald A. Dahlstrom

INTRODUCTION Solid-liquid separation is an important and many times a critical step (or steps) in a mineral or coal processing plant. Some examples of typical critical separations are as follows: 1. Operating a seven to eight stage CCD thickening circuit to re¬cover almost all of the caustic and alumina trihydrate values in an alumina plant. This must be accomplished with highly scaling slurries, starting temperatures of over 100°C and operate on a closed circuit system. 2. Making a filter step operate to produce a proper moisture for the balling step so that the pellet furnace can produce a proper product. Bentonite addition must be minimized and a good quality filtrate must be maintained to prevent abrasion of the internal parts of the filter. 3. Operating a closed water system in a coal washing plant so that reclaimed water containing less than one percent suspended solids is produced for reuse to maintain beneficiation ef¬ficiency. Refuse solids must also be thickened so that they can be effectively dewatered to meet state disposal requirements. 4. Recovering phosphoric acid values from a slurry containing gypsum and other gangue solids at an elevated temperature. This must be done while minimizing wash water and maximizing P2O5 re¬covery while simultaneously minimizing scale problems. While solid-liquid separations are important to overall performance in the processing plant flowsheet, it is also a significant factor in plant costs. Capital and operating costs for all the solid-liquid separation steps (includ¬ing water reclamation for reuse) in such plants are probably between 10 and 20%. Energy consumption can also be important in these separations. For example, in the copper concentrator, it is the third largest category in energy consumption, after comminution and flotation. Obviously, solid-liquid separation steps in a plant demand proper atten¬tion in design in order to achieve both optimum performance and cost. Simultaneously, knowledge of funda¬mentals are important to improve results in existing plants.

Jan 1, 1986

By Ian P. G. Hutchison

12.1 INTRODUCTION This chapter deals with the tools required to design leach operations to minimize spillage from leach pads and ponds and erosion damage during flood events or prolonged wet periods. It outlines methods used to design for prolonged dry periods when water shortage can be a problem. Seasonal operational aspects such as winter shutdown and coping with spring snowmelt periods are also discussed. General criteria useful when designing pregnant and barren solution ponds are also outlined. The aim of these notes is to provide designers and operators with a simp1ified approach to developing design parameters which make effective surface water management easy to achieve without resorting to extensive or elaborate analyses. Section 12.2 briefly outlines the types of problems associated with wet climates and floods, as well as dry periods. Determination of flood design parameters is discussed in Section 12.3. Circuit water balance and pond sizing are outlined in Section 12.4. Pond design considerations are included in Section 12.5. Worked examples are included in Section 12.6. 12.2 RAINFALL/RUNOFF PROCESSES There are two types of rainfall-runoff processes that are important when designing heap leach facilities. The first of- these is the short-term, intense rainfall or snowmelt events that occur over a period of a few minutes or hours, causing flooding that can lead to erosion damage and overtopping of ponds and containment dikes. Specific problems that can manifest themselves during these events include: • Washout of access roads; • Damage to containment dikes; • Flood water contamination of circuit water; • Damage to process water ponds by perimeter erosion or overtopping and erosion; • Loss of process circuit fluid due to breaks in containment dikes or process water ponds; and • Erosion of leach pile and consequent sediment contamination of process fluid. Other types of rainfall -runoff processes that could cause problems are the long-term-(generally months-long) wet or dry periods. Extended wet periods

Jan 1, 1988

By M. S. Kabibwa, E. K. C. Chanda

In planning for the future, Nkana Division deepened the Mindola sub-vertical shaft which was commissioned in 1994 in order to access the 30 Mt of ore between 1274 and 1570 m levels. The Nkana Synclinorium which is estimated to contain 250 Mt of ore is being accessed from the vicinity of Central Shaft. These areas are being planned with the intention of maximizing the use of computers in geological modelling and mine design so as to overcome the inadequacies of manual planning techniques. As a result, there is an increased demand for quality output from the computerized mine planning system the division has been developing over the last few years. A new workstation comprising the Hewlett Packard HP 71 51100 MHz and a CRX graphics monitor was acquired in 1995 together with the LYNX (version 3.09 and version 4.0) Mine Modelling System. Currently the workstation is being used for geological modelling and mine design for the Zerofold at Central Shaft and the Mindola mining at depth project. AutoCAD and Mine Works Planner have been added to the sys- tem configuration. Mine Works Planner is likely to replace Lo- tus123 for mine scheduling tasks. Computer applications in the area of mine planning at Nkana has led to considerable time savings and improved efficiency in areas formerly performed manually and has allowed speedy processing of data that would otherwise have proved too time consuming. Nevertheless, a lot of work still needs to be done in the areas of geostatistics, stope design and financial modelling of mining options. For the foreseeable future computer based planning will operate parallel to manual methods until such a time as sufficient personnel are proficient in the use of computer systems. This paper describes the program of computerization at Nkana Division, reviews current applications and the benefits and experience gained and discusses the promise of current and future developments.

Jan 1, 1996

By Betty L. Gibbs

A short course, held during the SME Annual Meeting in Phoenix, AZ in February, focused on software for surface and underground mine modeling. The objectives of the short course were to review techniques for surface and underground mine planning. Mine planning software vendors were invited to demonstrate how their software runs, given a standard data set. Six vendors of mining-specific software participated in the workshop. They were Exploration Computer Services (MINEX 3D), GEMCOM Services, Inc. (PC-MINE), KJRA Systems (VULCAN), Mine Development Associates (SURPAC), Micromine and MINEsoft (TECHBASE). Data set A data set was created to challenge the capabilities of each vendor&apos;s software. The criteria used for the data set selection were: • a minimum of 300 drill holes; • the data must include topography, drill hole survey, assay and formation contacts; • the deposit was multimetallic; and • there was the potential to be mined by surface and underground methods. The data set used was an actual, complex copper ore body with a small amount of gold. The ore body was close enough to the surface to be mined by surface techniques. Part of it, though, was also amenable to underground mining. To further complicate the problem, a river ran across the area of the ore body. This presented mine planners with the problem of either moving the river or mining around or below it. The ore body had not been mined, so no data was available for the tons and grade actually produced. Data for the mine planning problem was distributed to each vendor about two months before the short course. They had the opportunity to load the data into their systems, build an ore body model and perform preliminary work. During the first day of the workshop, the vendors received problems concerning the ore body. They went to work on their machines, attempting to show short course participants how their software could help solve the problem.

Jan 1, 1992

By Huayang Luo, Hui Li, Wei Zhou, Gang Chen, Scott Huang

Abundant beach and offshore resources of gold deposits are demonstrated along the coast of Alaska, and Nome is one of the richest places. Considerable amounts of mineral resources data were collected and stored in geodatabase of ArcGIS. In searching for the best model for the interpretation of the Nome offshore gold placer deposit and accurate estimation of the reserve, the data were processed and visualized using ArcGIS. The gold concentration data collected from the Nome offshore deposit are of characteristics such that: (1) near lognormal distribution of data, (2) high positive skewed distribution, (3) a small number of extreme values dominating the reserve estimation, and (4) apparent anisotropy of the variogram. These characteristics make the development of an interpolation model for the gold deposit a challenging task. In this study, it is determined that five geostatistical methods provided by ArcGIS with visualization capability, i.e., Inverse Distance Weighted (IDW), Ordinary Kriging (OK), Ordinary Kriging with lognormal transformation (OK-log), Simple Kriging (SK) and Indicator Kriging (IK) are suitable candidates for the development of an interpolation model. The five algorithms are evaluated and compared with each other in the study. Cross-validation technique is employed to examine the accuracy of the five approaches. It is determined that the OK and SK algorithms are not suitable for this dataset because of the difficulty of fitting the semivariogram model despite their lower RMSE (Root-mean-square error) and the higher RMSS (Root-mean-square Standardized). The OK-log algorithm does not provide satisfactory prediction either, because it places too much weight on the role of extreme values resulting in overestimation and extremely high RMSE. Reserve estimation of each blocks is conducted using each of the interpolation methods and compared with the reserve calculated using the conventional polygon method. The IWD and IK algorithm seem to provide estimations more agreeable with the conventional polygon method.

Jan 1, 2005

By Jeong-Heum Kim, Jan M. Mutmansky

The primary purpose of the research summarized in this paper was to experimentally investigate the performance of numerous mine ventilation network iterative solution procedures under controlled conditions to determine which procedures were most favorable in terms of number of iterations and total computational speed. The solution methods investigated included: (1) the Newton-Raphson method, (2) the Hardy Cross method, (3) the linear theory method, and (4) the second-order approximation method. The first three of these methods have been widely used while the fourth was formulated by the authors to investigate its potential for ventilation network computation. In addition to the four solution procedures, three methods for selecting the branches in the meshes and three methods for ordering the meshes for computational purposes were also studied during the investigation. As a result of these various options, a total of 36 combinations of solution methods, mesh selection procedures, and mesh ordering schemes were studied. To investigate the performance characteristics of these combinations, an identical set of 180 randomly chosen ventilation networks was used in sets of 30 networks at six different levels of complexity. Here, the level of complexity is defined as a function of the size (number of branches) and the density (number of nodes compared with the number of branches) of the network. To eliminate variations in the solution times due to differences arising from the fans, a single fan with a fixed characteristic was utilized in all the experiments. This paper will deal only with the results for the four iterative methods used to achieve solutions to the mine ventilation networks. The minimum-resistance spanning tree method for mesh selection and random mesh ordering was used throughout the analysis. The conclusions will be based upon a detailed accounting of the efficiency of each method using the total time to achieve a solution to each problem and averaged over the total problem set. However, the number of iterations and the time to complete each iteration will be studied in order to better understand the solution procedures.

Jan 1, 1991