Search Documents

By Danforth R. Hale

The pressure of military use of quartz resonators led to efforts to Grow high, grade quartz crystals in Germany and in Great Britain during 19)3-25, and was responsible for a series of U.S.A. Signal Corps contracts beginning in 1946 with the Clevite Corporation (as the former Brush Development Company), Bell Telephone Laboratories, Antich College, and others. The technique of growing crystals from the melt, such as KI, NaBr, was already commercially inuse Quartz could not be so grown, since its utility depends on the form stable below 573°C, and, even if it could be grown from an extraordinarily viscous melt, the higher form passing through this transition becomes twinned. Again, several crystals were being grown commercially from water solutions; quartz, however, is listed in the common literature as being insoluble in water. Fused quartz, or vitreous silica, was chosen as raw mater¬ial by the European experimenters because of its thermodynamically lesser stability than quartz, and various alkaline solutions were tried for the purpose of enhancing the solubility.

Jan 1, 1964

By Charles H. Greene

This paper will describe briefly the steps taken in the development of a Central Florida phosphate ore deposit from acquisition to mining. Further, the design and early operation of the mining and beneficiation facilities will be depicted. During the 1950's, with confidence in the continually increasing requirement for phosphate fertilizer materials essential for producing food, I'. R. Grace & Cc acquired the Hookers Prairie tract containing approximately 45 million metric tons o. (50 million short ton~ of potential phosphate rock product. In 1973, at a point when the Grace captive need for rock was being greatly enlarged by a planned doubling of its Bartow phosphate chemicals plant capacity, the decision was made to expand existing phosphate rock production by building a new mine and plant. The initial annual capacity was to be 2.3 million tons (2.5 million st); however, subsequent investigation pointed to a higher than estimated dragline operating factor 'and the forecast of annual capacity was set at 2.5 million tons (2.8 million st).

Jan 1, 1977

By E. R. Hendrickson

About 1/3 of the world's supply of phosphate rock is produced in a relatively small area of the Florida peninsula east of Tampa. Until this past year, a circle with a radius of about 25 miles and centered on Bartow would encompass the major producing areas. During the past year producing areas have opened in North Florida which promise to vie with the Polk-Hillsborough County area in terms of proven reserves. In addition, new phosphate production is planned for counties to the south and west of the present fields. From the existing production areas, however, more than 19 million long tons of phosphate were mined in 1965. As mining engineers most of you probably are familiar with the methods of mining and beneficiating the pebble phosphate rock. You thus recognize that, although some water quality problems may arise from these processes, there is no potential air pollution problem. To make an economically useful product, however, further processing must take place. It is from this additional processing that potentially damaging materials may be discharged to the atmosphere.

Jan 1, 1966

By Robert M. Cox

Systematic roof bolting has proven to be a very effective method of mine roof control; however, major roof failures still occur and roof falls still remain the number one occupational hazard of underground miners. Why do some bolted mine roofs fail, while the vast majority of bolted mine roof remains stable and safe to work under? Observations of numerous roof failures indicate that most of the major roof failures* are associated with either: 1) Jointing, faulting or other structural fracture zones; 2) massive shale beds of lenticular structure, or 3) thinly laminated sand-shales. The jointing and faulting present an obvious weakness in the roof rock structure; whereas, the massive shales and laminated sandy-shales create a roof structure with low shear strength and/or modulus of deformation. An observation of major significance is that most bolted mine roofs fail as a unit, and that the thickness of the fall is roughly equivalent to the roof bolt length (See Figure 1). In fact, several operators have experienced the phenomenon of an increase in roof fall thickness with an increase in roof bolt length.

Jan 1, 1973

By L. S. Harris

The application of briquetting in various chemical, mineral, mining and metallurgical processes has been rapidly increasing in the past two decades. This is, in part, due to the development of new, more economical and higher performance briquetting equipment. Some of these developments, which have reduced the operating and maintenance costs,, include anti-friction bearings, hydraulically applied pressure enclosed and sealed gearing and bearings, tapered predensification feed screws, water cooling and materials of construction capable of operating at temperatures up to 18000F, and control systems capable of maintaining optimum briquette quality control. The briquets can be formed into almost any desired size and shape, To date, with present rotary briquetting presses in the 25 to 500 ton force range, briquets from 1/4" to 6" length are presently being used, some of which are illustrated in Figure No. 1. In force fed rotary briquet machines, these shapes are produced by feeding the material in between a pair of counter rotating rolls, as illustrated in Figure No. 2. The rolls have forming dies indented into their circumferential surface, as illustrated in Figure No. 3.

Jan 1, 1973

By Theodore Balberyszski

The gradual depletion of high-grade sulphide mineral deposits has turned the attention of the mineral industry to the recovery of metals from the oxides and silicates. Anionic (fatty acid) and cationic collectors have in some cases made flotation of non-sulphides possible, although in general, flotation of oxide ores is not as yet an economic process. Consequently, many attempts have been made to sulphidize the surface of the relevant oxide mineral and thus make it amenable to flotation. (1) (2) (3) In recent years, Bautista and Sollenberger(4) have investigated the conversion of a number of oxides to sulphides by reacting them with molten sulpur. This paper presents the results of investigations carried out at the School of Mineral and Metallurgical Engineering at the University of Minnesota to study the flotation characteristics of some sulphidized minerals. It is divided into two parts; Part I describes the sulphidization of a number of oxides and a silicate, and Part II presents the flotation behavior of the products of sulphidization.

Jan 1, 1968

By V. D. Hanson

When maintenance of a plant or operation is under discussion immediately three "M's", all in short supply, are brought to mind - money, men and markets. This paper will present what currently is being done at our plants and its effect on the 3 "M's". Examination of coal realization figures (F.O.B. Mine) from 1945 to the present reveals the fact that open and free competition can and will meet market conditions. The industry, without benefit of advantages afforded tax and transportation wise to oil and gas, remains the backbone of the energy market of United States. Figure No. 1 shows the realization figures from 1945 through 1962 compared to the hourly earnings. Note that through 1945 to 1948 F.O.B. prices increased $1.93 per ton while hourly earnings increased $.66 per hour. Since 1948 (with the ex¬ception of 1957) F.O.B. prices have declined $.45/ton, while hourly earnings have increased $1.23 per hour. Basically the maintenance men possibly represent the highest increment rate in the overall hourly earning.

Jan 1, 1963

By Allegra Yeley, Ted Klemetti, Gamal Rashed, Tim Miller, Nicole Evanek

In 2015, the Subtropolis Mine in Petersburg, OH, experienced a massive ground collapse that continues to grow over time. Horizontal stress effects have affected the roof at this operation in the past and may have played a large role in this collapse. Horizontal stress can impact the roof and floor stability and endanger the health and safety of underground stone miners. Mines experiencing damaging effects from horizontal stress typically find that the principal stress direction is the same throughout the mine and the region. At the Subtropolis Mine the principal horizontal stress direction appears to change as conditions change and differs from the regional horizontal stress, particularly near the collapse or other roof fall areas. The growth over time of this collapse and other roof falls have been captured and analyzed using geologic mapping, 3D LiDAR scanning, numerical modeling and geographic information systems like ArcGIS. Utilizing these tools to better understand sitespecific conditions can be critical to reducing the potential of massive ground collapses in the underground limestone industry.

Feb 1, 2024

By Kenneth S. Johnson

Oklahoma is a region of complex geology where a mobile belt of Paleozoic geosynclines and uplifts on the south abuts against the margin of the North American craton to the north. The state contains many classic areas where fundamental concepts of sedimentation, stratigraphy, structural geology, historical geology, mineral investigation, and petroleum exploration have been formulated through the years. In the southern Oklahoma mountain belts, there are exposed a great variety of igneous and sedimentary rock units seen at few other places in the Midcontinent area. Major geologic provinces of Oklahoma (Fig. 1) include: (1) the cratonic and relatively stable northern shelf areas, including the Ozark uplift; (2) the Ouachita geosyncline (now the Ouachita Mountain belt) and associated Arkoma basin in the southeast; and (3) the southern Oklahoma aulacogen (geosyncline), comprising the area of Anadarko, Ardmore, Marietta, and Hollis basins, as well as the Arbuckle and Wichita Mountain uplifts. The three principal fold belts, the Ouachitas, Arbuckles, and Wichitas, all originated from a series of Pennsylvanian orogenies (about 300 million years ago) in the two Paleozoic geosynclines.

Jan 1, 1999

By James J. Scott

Introduction Friction Rock Stabilizers, trade name Split Sets, are presently under research and development by Ingersoll-Rand Company and Dr. James J. Scott, inventor. Conceived in 1953, the system is a patented process undergoing extensive field and laboratory testing. The author has published papers on the Split Set System earlier (References 4, 5, 6) The Split Set System holds promise to be a revolutionary development in the field of ground control. The system produces an interior reinforcement to a rock mass which: 1. Is simple in its concept. 2. Adjusts to the degree of restraint needed to match rock properties. 3. Provides a yieldable support and, later, a more rigid support as it is needed. 4. Pre-loads the rock in compression to increase stability. 5. Is a full-contact, fully tensioned device to resist rock loads. 6. Minimizes the stress concentration effects inherent in many interior support devices. 7. Improves safety for the miner. 8. Is cheaper than a grouted system. 9. Offers the rock mechanics engineer an opportunity to design in a fashion not before possible.

Jan 1, 1977

By W. S. Urbanski, A. L. Devernoe, M. S. Walker

Theory and practice are described for a new processing method capable of precise mineral separations based primarily on differences in particle specific gravities at specific gravity split points from 1.5 to 21.0 and beyond. Separations are analogous to those achieved using rotating heavy media, except that the effective specific gravity of the fluid is created magnetically using a relatively dilute, low-viscosity, water-based magnetic fluid. Results reported here for a large, laboratory flow-through separator include: 1) 99% grade with 97% recovery in single pass separation of a suite of heavy minerals from quartz at I0 kg/h, 14 tph/rm2 of duct cross section, 2) 90% grade and recovery in single-pass separation of mixtures of sand-size, non-magnetic rutile (4.23 specific gravity) and zircon (4.72 specific gravity) at throughputs of 35 kg/h, 47 tph/rm2 of duct cross section, 3) partition curves having Ep90-10 transition widths 5% or less of mineral specific gravities, and 4) essential confirmation of the theory.

Jan 1, 1991

By Janusz S. Laskowski

Studies carried out over the last 10 years reveal that precipitating particles which may appear in alkaline solutions of long-chain amines and in acidic solutions of fatty acids exhibit clear isoelectric points around pH 10.6-1 1 for dodecylamine and around pH 2.5-3 for fatty acids. These colloidal species can accumulate at solid/liquid and liquid/gas interfaces and affect flotation. While the precipitate in solutions of fatty acids apparently can chemically interact with the mineral surfaces and is flotation-active if sufficiently long conditioning time is available, the cationic flotation of quartz in alkaline solutions is depressed by the colloidal precipitate. The experimental data available in literature on the adsorption, electrokinetic, contact angle and surface forces measurements in the solutions of the weak electrolyte collectors are analyzed and the role played by the precipitate is discussed. It is shown that these concepts allow for an explanation of the selective flotation of sylvite from halite with long-chain amines in potash ore flotation.

Jan 1, 1999

By Thorvald Wetlesen

Computer controlled drilling is now proven technology. It was first introduced by the development of the Furuholmen system for a prototype three boom tunneling jumbo in Norway in 1978. Now, 13 rigs with this concept are in operation in Europe, 3. in mining in England and. 10 in tunneling elsewhere in Europe. The system is also adapted to roadheader guidance. Practical experience has shown that the computer control system makes it possible to drive tunnels with a more accurate contour thus reducing the total amount of rock excavated, and where a full concrete lining is required a reduction in concrete volume is achieved. The total tunneling economy is improved. In the future we expect to see a wider range of instrumentation on jumbos, from the simple direction instruments to computer guidance systems for monitoring only, as well as fully automatic drilling to a programmed drilling pattern. More compact and reliable electronics will be available. Systems with low power consumption will fit easily into flameproof applications. Cabling complexity will be reduced by connection of sensors to serial signal lines.

Jan 1, 1989

By Noris Del Be1 Belluz

Drilling underground in the Grasberg dewatering drifts has routinely hit water aquifers with high flow rates and pressures. Two types of holes are used. Pilot holes probe ahead of the tunnel development to intersect aquifers ahead of the face. And dewatering holes dewater rock formations that will drain water from the Grasberg pit and allow tunnel development to proceed safely. Recently, static pressures of >8.3 MPa (> 1,200 psi) have been recorded with flows from a 100 mm (4 in.) HQ core hole measured at 5,700 L/min (1,500 gpm). The waterflows can be slightly acidic, necessitating the use of stainless-steel collar gear to resist corrosion. These rates were anticipated and contingencies were planned early on to deal with these conditions. PT Freeport Indonesia (PTFI) established procedures to maintain the safety of the drill crews, to enable coring of the rock, and to maintain the safety of the miners driving the drifts. The collar gear controls the waterflows because these drill holes are a vital source of water for the concentrator.

Jan 1, 1998

By L. Yuan, J. Soles, D. Bahrami, W. Tang, R. Thomas

Mine equipment fires remain as one of the most concerning safety issues in the mining industry, and most equipment fires were caused by hot surface ignitions. Detailed experimental investigations were conducted at the NIOSH Pittsburgh Mining Research Division on hot surface ignition of liquid fuels under ventilation in a mining environment. Three types of metal surface materials (stainless steel, cast iron, carbon steel), three types of liquids (diesel fuel, hydraulic fluid, engine oil), four air ventilation speeds (0, 0.5, 1.5, 3 m/s) were used to study the hot surface ignition probability under these conditions. Visual observation and thermocouples attached on the metal surface were used to indicate the hot surface ignition from the measured temperatures. Results show that the type of metal has a noticeable effect on the hot surface ignition, while ventilation speed has a mixed influence on ignition. Different types of liquid fuels also show different ranges of ignition temperature. Results from this work can be used to help understand equipment mine fires and develop mitigation strategies.

Mar 2, 2022

By R. E. Johnson, J. E. Dutrizac, B. R. Palmer

Silver sulphide (acanthite) and lead sulphide (galena) dissolve relatively rapidly in FeCl3 media with the formation of elemental sulphur and soluble silver and lead chlorides. Parabolic kinetics are observed, and the leaching rates are controlled by the outward diffusion of the AgCl and PbCl2 reaction products through the constantly thickening elemental sulphur layer formed on the sulphide. Hence, both leaching rates are strongly dependent on those variables which affect the solubility of AgCl or PbCl2 at the reaction interface. The rates therefore increase with increasing temperature and total chloride ion concentration, but decrease in the presence of elevated concentrations of AgCl or PbCl2. By contrast, neither sulphide is significantly attacked by ferric sulphate media, even at high Eh values. Although the reasons for the refractory behaviour of Ag2S in sulphate media remain unknown, the low rate of PbS attack is attributable to the passivating layer of PbSO4 and elemental sulphur formed on the surface of the galena.

Jan 1, 1993

By Hetland Donald L.

Regional Tertiary formations and basins of local sedimentation which contain uranium deposits west of the Rocky Mountains are mainly of Oligocene, Miocene, and Pliocene age (fig. 1). The host rocks have been derived mainly from intrusive and extrusive igneous rock. The major host formations which cover broad geographic areas include the Esmeralda, Truckee, Humboldt, Thousand Creeks, Payette, Panaca, Cedarville, Coso, and San Joaquin Formations. Local areas of Tertiary sedimentation containing uranium deposits occur near Yuma, Safford and Artillery Peak, Arizona; Dillon and Canyon Ferry, Montana; Spokane Indian Reservation and Pend Orielle River, Washington; Topaz Mountain, Utah; Stanley Basin, Idaho; and Sonora Pass, California. Uranium deposits in these sediments have been classified into five categories based on environment (fig. 2). They are: (1) Deposits in lake sediments consisting mainly of water-laid tuffs; (2) Deposits in lake sediments intruded by volcanic plugs; (3) Deposits in lake sediments interbedded with arkoses near batholiths; (4) Deposits in coarse volcanic sediments in local sedimentary basins; (5) Deposits in arkosic conglomerates in local sedimentary basins.

Jan 1, 1969

By M. S. Janssen

The development of a design equation for, and the testing of, a constant- flow airlift pump IS described. The predictions of the new airlift model agree with the results of experiments carried out using riser diameters between 0.025 and 0.300 m, submergence depths between 5 and 10 m, suspension densities between 1000 and 1650 kg/m3, and a solids dg of 70 to 100µm. The predictions o the model also agree with data from the literature for submergence depths that reached 130 m. This airlift model was employed to simulate the pulp flow through a series of tanks, each of which was fitted with an airlift pump to transfer the suspension to the next tank. Particular attention was paid to the riser diameter, submergence of the airlift pump, and control of the air supply to the airlift pump during the simulated operation of a series of tanks. The results of the simulation highlight some design parameters that could affect the efficiency and operation of a plant that employs airlift pumps to transfer suspensions.

Jan 1, 1989

By R. Hogg, L. G. Austin, R. C. Klimpel

Slurry densities and holdup were measured for open circuit grinding tests in a laboratory overflow ball mill of 0.3 m diam by 0.6 m long, by emptying and drying after stoppage of the mill. Contrary to some other results in the literature, there was negligible variation of slurry level in the mill as a function of flow rate over a range of increase of flow rate of about 5 to I. However there was a gradual increase of solid holdup at higher flow rates because the slurry density in the mill increased. Equations are given for holdup and slurry density in the mill as a function of over flow diam, ball load, and feed slurry density. The average level of slurry necessary to give over flow was found to be much higher than that necessary to fill the mill to the overflow level at rest. The total level of balls and slurry was only increased slightly by ball loads higher than the overflow level. The overflow diam appeared to be the major controlling factor in determining the mill holdup.

Jan 1, 1990

By D. V. Professor Keller

The production of premium coal-based fuels (<3% ash) and ultra clean coals (<1% ash) using the process of selective agglomeration requires proper selection of raw coal, rough preparation procedures, milling equipment, product coal size distribution, water purity, agglomerants, agglomeration equipment and operational procedures. Each of the variables can contribute a small fraction to the impurity load in the product coal or limit the ability of the process to separate mineral matter-free coal. Each of the variables and their importance will be examined from data produced at the bench by batch and continuous agglomeratons as well as the results from pilot plant and tonnage production units. The results are discussed which have indicated that some standard commercial coals can be produced with ash contents as low as 0.2 % ash (batch/bench) and several tonnage lots of 0.6% ash in as 200 lb/hr pilot plant. In most cases iron pyrite released from the coal matrix and with proper pH control is rejected from the product coal agglomerates.

Jan 1, 1995