Search Documents

By Nora M. Hutt, Kevin A. Morin

One technique for controlling ongoing acidic drainage is to relocate and submerge net-acid-generating waste rock in a lake or water-retaining impoundment. This can lead to the overall improvement of water quality and the reduction In short-term environmental liabilities. A case study of this technique is the Eskay Creek Mine in northern British Columbia. Some findings of the study are: (1) the addition of lime to each truckload of rock, based on its rinse pH, neutralized the accumulated acidity and suppressed the accumulated-metal release, (2) only 10-20% of the dump's neutralization potential had been consumed when acidic drainage appeared, (3) water chemistry in the watershed recovered roughly three years after relocation, and (4) environmental liability was reduced due to the cessation of on-land acidic drainage with no degradation of lake chemistry.

Jan 1, 2000

By A. Gene Collins

The demand for lithium may increase because of its potential use id lithium batteries and in the generation of electrical power by fusion. Therefore, lithium abundance in some United States oil-field brines was surveyed. Oil-field brines from numerous locations were found to contain more than 100 mg/l lithium and several exceeded 500 mg/l. An area of 25,000 km2, with a reservoir thickness of 60 m, an effective porosity of 5 percent, and a brine with a specific gravity of 1.2 containing 100 mg/l of lithium, contains about 0.75 x 106 tonnes (1 tonne = 1 metric ton = 1,000 kg) of lithium in 7.5 km3 of brine. It is postulated that the brines were enriched in lithium by lithium-rich spring water or lithium leached from volcanic rocks followed by evaporation sequences.

Jan 1, 1978

By Richard M. Crowell

"As thorough sampling is usually expensive, the cost of a complete job is often unwarranted, and a cheaper approximation must be substituted. The engineer should, however, weigh the situation thoroughly before subscribing to an alternative other than an accurate assay basis on which to build his conclusion." Examination and Valuation of Mineral Property. R. Parks, 1949

Jan 1, 1994

By R. Robertson

Dense medium cyclones are the preferred means for cleaning 112 in. x 14 Mesh to 28 Mesh (12.7 mm x 1.0 mm to 0.6 mm) raw coal and are becoming a common choice for cleaning raw coal from a nominal top size of 2-1/2 in. to 3 in. (63.5 mm to 76.2 mm) down to 14 Mesh to 28 Mesh (1.0 mm to 0.6 mm). During the last ten years, dense medium cyclone circuitry design has undergone changes which have combined to improve process efficiency. This paper describes these improvements and compares present day design with the design used prior to the mid 1980's. Improvements in the following areas are described: Raw coal desliming, cyclone configuration, drain and rinse applications, dilute medium circuitry, and instrumentation and control.

Jan 1, 1997

By B. Strickland

The decision to accelerate development of Stillwater Mining's East Boulder Mine was made in March of 1998. It required the completion of conceptual designs by July of 1998. This was accomplished through teamwork and close cooperation of mine personnel, engineering firms and vendors, all working toward the common goal of developing an efficient and workable design. Early in the project, representatives of Stillwater Mining, Kilborn International, Parsons Brinckerhoff Transit and Rail Systems, Continental Conveyor, and H.A. Simons met to develop methods to bring the mine into production at a highly accelerated rate and to solve potential bottlenecks, including the movement of personnel, materials, and muck through a 5.6 km (3-1/2 mile) adit. This interaction, including companies not normally associated with the mining industry, led to innovative approaches and designs produced by Kilborn Engineering and Stillwater Mining.

Jan 1, 1999

By G. Roy, C. B. Pettersson, S. Nandagiri, D. J. Ivor-Smith

The Coastal Water Authority's 2,740mm/2,590mm (108 in./102 in.) pipeline, known as the Northwest Lateral Project, will transport raw water from an existing pipeline over 14.3 km (8.9 miles) to the City of Houston's East Water Purification Plant. The new pipeline crosses under Houston Ship Channel and Greens Bayou in tunnels at approximately 30.5m (100 feet) and 25.9m (85 feet) depths, which present unique experiences in tunneling under open bodies of water in the Gulf Coast's soft ground conditions. An earth pressure balance TBM is being used for the deep tunnel sections where the ground demonstrates high overload factors and variable conditions ranging from clays to silty sands. This paper discusses the design approach for the tunnels and shafts, ground conditions, constructability, and selection of the primary lining system.

Jan 1, 1989

By D. M. Cregger, J. L. Rosenblad, R. E. Ranken

The construction of a large span, high-walled underground opening in a low strength shale rock is unprecedented. The feasibility of constructing a pumped storage project with several tunnels and a large underground powerhouse in low strength shale rested largely on the feasibility of building stable openings large enough to accommodate the required equipment. Because of the lack of experience with large openings in shale, the decision was made to excavate a test adit and test chamber and conduct a multi-faceted geotechnical evaluation program designed to yield pertinent in-situ data on the ability of the shale to accommodate a large underground opening. Factors considered in the shape, size, orientation, and location of the test chamber were: (1) similarity to the anticipated powerhouse chamber, (2) nature of the most important data to be obtained, (3) feasibility of construction, and (4) economics.

Jan 1, 1983

By Robert S. Hendricks

The paper describes the design and operation of a Shaft Boring Machine (SBM). The machine has been developed by The Robbins Company. It is anticipated that the prototype, which will bore shafts in the 6.1 to 7.3 m (20 to 24 ft) size range, will be placed in operation during 1985. This pioneering application of rapid excavation technology is expected to lead to significant improvements in the cost and speed of shaft construction. The technical and economic factors which have limited the employment of Shaft Drilling and which caused unsatisfactory results with earlier attempts at Shaft Boring are reviewed. The design criteria adapted to overcome these problems are discussed. Cost and performance estimates are presented and are compared to conventional sinking methods. Factors that influence the application of the SBM to specific projects are reviewed.

Jan 1, 1985

Continuous improvement has become the watchword of the 1990s for most iron-ore-processing operations. In many instances, this improvement has been achieved through stepwise application of advanced control techniques to optimize operations. The benefits of this stepwise application have been great. However, they have fallen short of the full potential offered by the prospect of overall plant optimization. The successful integration of computers, instrumentation and control software throughout a plant promises to deliver an additional 3% to 5% of productivity in even the best-run plants (Herbst and Bascur, 1984). LKAB is Europe's largest iron-ore producer and a leading implementer of advanced control technology. In the late 1980s, LKAB introduced advanced control in its concentrator at Kiruna, Sweden to improve plant performance through higher productivity, greater efficiency and lower costs at each processing step.

Jan 1, 1995

By S. R. Rao, J. A. Finch, E. El-Ammouri, K. Ngoviky, P. A. Disten

Sludges produced by lime treatment of acid mine drainage (AMD) can contain significant quantities of base metals which represent both a potential hazard and a loss of values. A new technique for metal recovery from sludge is proposed by combining selective acid leaching and adsorption of metal ions by activated silica sol. The process is demonstrated on two AMD sludges, one containing primarily nickel and the second zinc. They were first treated with sulphuric acid (pH 3.5) to selectively leach the target metals and then activated silica sol was added to the leach solution to adsorb the nickel and zinc. Thickening and centrifuging gave about 90 percent rejection of the input volume to effluent. The adsorbed metals were redissolved by strong acid into a concentrated solution relative to the feed and the silica sol was recycled.

Jan 1, 2000

By G. Myers, C. J. Wendt, W. H. Wilkinson, M. D. Dennis

Precious metal mineralization at Mt. Hamilton, NV is associated with a polymetallic, garnet-pyroxene skarn system developed in middle to upper Cambrian calcareous shale, limestone, and dolomite. The skarn is developed around the Cretaceous Seligman and Monte Cristo calc-alkaline stocks. Gold is associated with intense retrograde alteration. Later epithermal quartz veins contain gold, silver, base-metal sulfides, and sulfosalts cross-cut skarn alteration. Westmont Mining Inc. is currently developing two mineralized zones containing a geologic resource of about 7 Mt (7.7 million st) that averages 1.7 g/t (0.05 oz per st) gold and 17.2 g/t (0.5 oz per st) silver. The project will have an estimated mine life of seven years, with a planned annual production rate of I t (35,000 oz) of gold and 9.3 t (300,000 oz) of silver.

Jan 1, 1990

By V. K. Gupta

A detailed experimental study of the variations in grinding rate with particle size, particle load, ball diameter, ball load, mill diameter, and mill speed was carried out for a soft cement clinker and a hard cement clinker. The effects of the ball diameter, ball load, and particle load were observed to be material (hardness) independent, and those of the particle size, mill diameter, and mill speed to be material dependent. A sharp change in grinding behavior was observed for both the clinkers at about 150 µm size. Below this critical size: (1) the hardness difference between the two clinkers became insignificant, (2) variation in the grinding rate with particle size became markedly more pronounced, and (3) mill speed had little or no effect on grinding rate. The importance of these results in the context of process optimization and control is discussed.

Jan 1, 1988

By R. R. Oder

Reported are weight, particle size, gross chemistry and magnetism measurements for lithic, mineral and fused soil components separated from five lunar soils using dry, open-gradient, magnetic separation. Pure diamagnetic anorthite, a feedstock for the electrochemical separation of oxygen and metals, has been separated from anorthistic highland soils. In addition, paramagnetic ilmenite has been separated from high-titanium, basaltic mare soils. Ilmenite, a feedstock for oxygen preparation by hydrogen reduction, may also serve as a source of He3 for use in fusion power generation. Agglutinates (vesicular, glassy components containing metallic iron) have been separated from all of the soils. Iron and refractories can be used for space construction. Metallic iron is easily detected in lunar soils by magnetic susceptibility measurements. Based on the exploratory laboratory results, conceptualizations of innovative magnets for processing lunar soils are presented.

Jan 1, 1993

By J. E. Rourke, O&apos

This paper describes the use of rock index property testing to obtain rock properties that a.re useful in the design and construction planning of an underground development for civil engineering or mining projects. The index properties discussed include (1) point load; (2) Schmidt hammer hardness; (3) abrasion hardness; and (4) total hardness. The first two index properties correlate to uniaxial compressive strength and Young's modulus. Discussions are given on the relationship to rock mass properties and the integrated use with semi-empirical, geotechnical design methods. The latter two properties correlate to construction performance parameters and some experience is cited. Examples of data are presented from an index testing program carried out on siltstone, sandstone and limestone rock core samples from a deep borehole drilled in the Paradox Basin of Utah for a nuclear waste repository site investigation.

Jan 1, 1988

By D. S. Kostick

Soda ash production in the United States during 1994 increased 4%, reaching 9.3 Mt (10.2 million st). That was the second highest production year. Domestic nameplate soda ash capacity is about 11 Mt (12 million st). Overall, the industry operated at about 85% of capacity. Some companies produced at 100% of capacity while others produced at below their design ratings. Although domestic soda ash consumption was slow during the first half of the year, third- and fourth-quarter sales increased, especially in the flat¬glass and fiberglass sectors. These two sectors increased because of greater demand for glass products in the automotive and construction industries. Soda ash sold for pulp caustic soda increased during 1994. This was due to higher prices for and reduced availability of electrolytic caustic soda. It is often preferred for pulp digestion because of its stronger alkalinity.

Jan 1, 1995

By P. Mousset-Jones, F. Calizaya

Currently, a 4.3 km long drift is being developed on the 3440 level in the Lower Kalamazoo project at the San Manuel Mine, Magma Copper Company, AZ. The drift, located at 1050 m below surface, is being constructed using a 4.6 m diameter tunnel boring machine (TBM). The drift is ventilated by a forcing type auxiliary ventilation system. At the face, to mitigate the impact on the work environment of the TBM, the system is equipped with dust extraction and refrigeration systems. Recently, to evaluate the ventilation conditions in the drift, a continuous monitoring system has been installed. The system can be used to measure the air velocity, barometric pressure, relative humidity and air and rock temperatures. This study describes the capabilities and limitations of this system, and presents a summary of the results.

Jan 1, 1995

By Kenneth N. Han, Xinghui Meng, A. J. Monhemius, G. W. Warren, E. Peters

The leaching of gold in ammoniacal solutions containing various oxidants in an autoclave has been investigated. Also studied are thermodynamic and kinetic aspects of the ammonia leaching of gold and silver. The variables studied included stirring speed, temperature, concentration of ammonia, ammonium, and various anions. Arrhenius activation energy values were found to be between 47.1 kJ/mol and 86.2 kJ/mol depending upon the kinds of oxidants used. An electrochemical reaction controlling mechanism has been proposed for the dissolution reaction. The leaching behavior of gold and silver from various ores in ammoniacal solutions containing various oxidants has also been investigated. The samples tested included sulfidic as well as carbonaceous refractory ores. The recoveries of gold and silver from these refractory ores were better than 96% within 2-3 hours of leaching time.

Jan 1, 1993

By Joseph Keenan

In March of 1994, Dynatec Mining Limited entered into a contract with PCL Civil Constructors to carry out the underground excavations for the Algonquin Power Corporation’s15 Megawatt Nagagami hydro-electric power station located near Hearst, Ontario, Canada. Dynatec completed the work for this project in early October 1995. Dynatec Mining Limited’s work included the excavation of a 175 meter long penstock driven at a grade of -25% to a 4000 m3 powerhouse located 50 meters below the intake elevation. A 1200 meter long tailrace was driven from the Nagagami River to connect with the powerhouse. Two 50 meter raises were driven from the powerhouse to surface to pro-vide access for equipment and personnel. The excavation of the tailrace tunnel(5.8m x 5.9m) was completed using Dynatec’s Long Round Jumbo Technology.

Jan 1, 1997

By Shunji Sukizaki

Recently development of cheaper and cleaner energy sources has become a more important and urgent issue, because of the soaring crude oil price and environmental problems such as global warming. In this social context, to establish basic technologies and solve fundamental issues associated with environmental impact assessments, the Environmental Impact Assessment Group of the Research Consortium for Methane Hydrate Resources (MH21 research consortium) in Japan has conducted a number of research and development activities since FY2001. These activities include: 1) surveys of the marine environment that will form the basis of environmental impact assessments associated with methane hydrate development; 2) the development of core technologies to monitor deep-sea environments; 3) research of major issues related to environmental impact assessments; and 4) the development of numerical models to predict the deformation of seafloor sediments containing methane hydrates.

Jan 1, 2008

By D. D. Banerjee, S. K. Kawatra, T. C. Eisele

A high calcium fluidized-bed combustor ash was shown to be an effective binder for iron ore pellets at dosages of 1 % to 2% of the magnetite concentrate weight. Magnetite pellets that were between 1.1 and 12.7 mm (7/16 and 1/2 in.) in diameter were produced with dry crushing strengths greater than 22.3 N (5.0 lb-force) per pellet, which is comparable to the results produced using conventional bentonite binder. The effectiveness of fly-ash-based binders was considerably improved when calcium chloride was added as an accelerator. The addition of calcium chloride at a rate of 0.1 % to 0.2 % of the total powder weight increased the strength of the dried pellets by as much as 22 % compared to the strength of pellets made using fly-ash without accelerators.

Jan 1, 1999