Search Documents

By R M. Whyte, D McArthur, A Macintosh

In designing a gold extraction circuit utilising carbon­in-pulp (CIP) technology a number of process options can be considered. These include various combinations of leach or pre-leach, CIP or carbon-in-leach (CIL) and conventional counter-current or carousel CIP (or CIL) circuits. Factors affecting the process selection include the project's sensitivity to capital and working costs, the project life, and the mineralogy and head grade. Each process option has it's own advantages and disadvantages. This paper compares both the financial and technical aspects of the flow sheet options. The flow sheet, design aspects and operating performance of Anglogold's West Wits No. 2 and 3 Plants which are leach, pump-cell circuits are described.

Jan 1, 2000

By D. B. Desai, J. T. Waggoner, J. S. Hill, R. R. Redd, S. J. Klein

The 13 km (8 mile) long Riverside Badlands Tunnel is planned for construction starting in 1998. Extensive geotechnical investigations indicate that the 3.7 m (12 ft) finished diameter tunnel will be excavated through soft ground, weak sedimentary rocks, and heavily fractured metamorphic rocks. Nearly 80 percent of the tunnel will be excavated beneath the groundwater level. Tunneling conditions are expected to range from raveling and over-stressed in the sedimentary rocks, to blocky and seamy/crushed with some squeezing in the metamorphic rocks. Two alluvium reaches will require dewatering. The variable and interspersed ground conditions are expected to be a key factor in selection of tunneling methods, equipment, and initial support.

Jan 1, 1997

By H. G. Linge

Pyrrhotite (FeS1+x ,0<x<0.15) is an iron sulfide which is considered to be a pest in carbon-in-pulp/ leach (CIP/L) gold processing [l].The perceived influence of pyrrhotite on gold processing by CIP/L is a competing consumption of 02 and CN­as the pyrrhotite dissolves by oxidation [1,2]. The few studies of the oxidation chemistry, kinetics and mechanism of the oxidation ofpyrrhotite are reviewed in detail elsewhere [3].There is broad agreement that the surface of pyrrhotite is very rapidly oxidized to form a thin (e.g. 10 nm) ferric hydroxy-oxide layer which overlays an iron-deficient sulfide lattice covering the original pyrrhotite. The reaction can be summarized thus:

Jan 1, 1995

By A. N. Islam, C. Simons, M. N. Hughes, J. Barrett

The effluent from the bio-oxidation of arsenopyrite contains high concentrations of iron(III) and arsenic(V), the pH being in the range 1.0-1.3. The use of lime to increase the pH causes the precipitation of calcium sulfate, calcium arsenate and a mixture of solids containing calcium, iron and arsenic. The presence of calcium is due to slaked lime encapsulated by the iron arsenate precipitates. These iron arsenate solids are related to known minerals. The use of sodium hydroxide to effect the precipitation of iron and arsenic produces solids which are more stable than those produce by using slaked lime. The use of limewater produces an initial precipitate of calcium arsenate.

Jan 1, 1991

By P. Gelfi, G. Hill, A. Showell, V. Martins, R. Dunne, R. Jenkins

Carbon attrition losses are not usually a prime consideration for CIP equipment selection and CIP plant design. However, the costs as a result of carbon attrition and associated gold lost with carbon can be high. Recorded carbon losses for Newcrest operating gold plants were shown to vary widely from plant to plant. The Tuckabiana plant recorded an overall loss of only 0.3g carbon /t ore which is very low by industry standards. A comparative carbon management study was undertaken by Newcrest to highlight the reasons for the excellent record of Tuckabiana operation compared to other Newcrest plants. This paper discusses the results of the comparative study and high­lights areas of concern with respect to carbon attrition.

Jan 1, 1995

By Wern-ping Chen, Joseph Pratt, Thomas G. Brueckner, Tracy K. Lundin

To address and mitigate discharges from combined sewer overflows in the Providence, Rhode Island area, the Narragansett Bay Commission completed a comprehensive Combined Sewer Overflow (CSO) Facilities Plan in 1993 which included a series of deep rock tunnels. Since completion of preliminary design of the program in 1994, the program has been reconfigured in response to the Environmental Protection Agency’s (EPA’s) new CSO policy. The currently proposed system consists of a deep rock tunnel with two tunnel stubs which will provide230,000 cu m (62 million gallons) of storage at depths of up to 90 m (300 ft). This paper discusses the revised 5 km (3 mile) long deep tunnel system.

Jan 1, 1999

By W. Lin, E. Heuze

This paper focuses on tests performed on sandstones and shales from four gas wells in the Mesaverde formation. A previous document showed a comparison of the static and dynamic laboratory moduli. This publication describes how field velocity logs were used to derive field dynamic moduli. A 3-way comparison was then performed for these stiffness properties; the results show no agreement between the three sets of values. Differences between dynamic stiffness coefficients from the field and the laboratory exceed 200%; differences between static and dynamic coefficients range up to 600%. In turn, this indicates that a reliable method of estimating mechanical rock properties for hydraulic fracturing design has not been established, and that such a task should be pursued.

Jan 1, 1986

By M. Z. Rashad

The purpose of this work is to determine the influence of sample length or size on the value of variance (Semivariogram) to select the suitable length that is required to the geostatistical computations of ore evaluation. Three cases in Ghorabi Iron Ore were studied. The first one was on the iron fraction (Fe%) at which the semivariogram gave an evidence to good continuity of the fraction in the ore. In this case, the length of sample has not important influence. The second case was for the Mn% component of the same area where the semivariogram has a nugget effect. The selected length for this case was 4 meters. The Cl% fraction of the ore was the third case where the anisotropic phenomena was appeared and the suitable length is 3 meters.

Jan 1, 1992

By Vernon N. Cox

From comments and questions concerning the meaning of USNR, and "why is the Navy in the mining business?" I believe it is worth while to establish the background and purpose of our company. We are a stock company formed by the purchase and reorganization of a company known as the U. S. Natural Gas Corporation. In May 1969, a group of investors with Mr. Robert L. Katz as president and chief executive officer, created United States Natural Resources, Inc., to develop and purposively use our Natural Resources in four areas: 1. Mines and Minerals 2. Forest Products 3. oil and Gas 4. Recreational Lands As final proof that we are not a government organization, I simply state. "We pay taxes." The mining division was formed in October 1969, with the completion of the merger of USNR and Vibration Measurement Engineers, Inc., Of Evanston, Illinois. Throughout the industry we were known as "VME," our company supplied consulting service in the field of seismic energy control, mining consulting and. we operated drilling, blasting and, contracting organizations in several areas of the country. Since that time we have developed and acquired producing properties in Quarrying, Coal Mining and Cement Copper Production.

Jan 1, 1971

By P. Schumacher, M. Fein

"INTRODUCTION Newmont’s Twin Creeks operation, part of its Nevada operations, produces gold from two large open pit mines. Mined ore is processed at one of three on-site facilities: a refractory mill with two autoclaves, an oxide mill and heap leaching facilities. Twin Creeks also processes various off-site sourced concentrates and ore including high grade underground ore from the Turquoise Ridge joint venture with Barrick Gold Corporation. This paper discusses Twin Creeks’ strategic mine planning process which is part of an in-depth continuous improvement program called “Full Potential.” The process involves cost analysis, phase design validations, life-of-mine production scheduling optimization, mill blending strategy and stockpile management. Through this Full Potential strategic planning, Twin Creeks is creating significant value by increasing near term free cash flow and life of mine net present value (“NPV”) and achieving cost reductions. TWIN CREEKS OPERATION Twin Creeks is one of the major gold producers in Newmont’s Nevada operations (see Figure 1, 2 and 3). Located approximately 15 miles north of Golconda, Twin Creeks produced approximately 28 % of the Nevada operation’s 2013 gold production of 1.8 million ounces (Newmont 2014). The production included Turquoise Ridge sourced gold ore from the joint venture (75% Barrick Gold Corporation, 25% Newmont).At Twin Creeks, there are two large open pits, named Mega Pit and Vista Pit (see Figure 4, 5 and 6). There are 3 to 5 phases in Mega Pit and 2 to 5 phases in Vista Pit depending on the gold price assumption. There is also an underground exploration project at the bottom of the Vista Pit. Twin Creeks produces gold from a variety of ore types requiring different processing techniques depending on economic and metallurgical characteristics. To ensure the best use of processing assets, engineering and processing groups at Twin Creeks utilize a Mixed Integer Linear Programming (“MILP”) model to guide the flow of mine sequences and material routing to various process facilities (Kawahata, Schumacher and Hufford 2013)."

Jan 1, 2015

By David J. Dunn

Mill liner design is an important factor in grinding. Testing and selection of the optimum liner profile for a given set of mill operating conditions can improve mill capacity, liner life, and liner wear rate At a time when mill avilability is at a premium, production costs are going up, and lead time for mill liner castings is a year or more, the mill liner that grinds best, lasts longest, and costs least is a necessity for economic mill operation. In testing four mill liner profiles for 13&apos; x 12&apos; overflow ball mills, Climax found that an improved design increased mill tonnage by 3 tons per hour while reducing finish grind by 1.7% + 100 mesh, reduced liner wear rate, and almost doubled liner life.

Jan 1, 1976

By W. J. Schlitt, J. H. Templeton

The chemical reactions that occur within a copper-leach recovery system are discussed, and the impact on the overall acid balance is evaluated. Both oxide and sulfide mineralogy are addressed, and their effects on acid consumption, generation and solution buffering are presented. Two case studies that apply the discussed chemistry show the practicality of using a computer spreadsheet acid-balance model for the early planning and design of copper-leach systems.

Jan 1, 1998

By S. K. Kawatra, V. Claremboux, S. Valluri

Carbon dioxide capture from coal-fired power plant flue gas and subsequent sequestration is expected to play a vital role in mitigating global climate change. To meet the growing need for CO2 capture Technology, Michigan Technological University is researching CO2 capture and Utilization. We have successfully converted CO2 into oxalic acid using an electrochemical approach. If oxalic acid can be produced in bulk from CO2, it can be used to leach rare earth minerals at low cost. Electrochemical reduction of CO2 to hydrocarbons and other chemicals is a complex multistep reaction with adsorbed intermediates. The exact reaction mechanisms leading to various products are not clear from the literature to date and will likely change over the range of conditions like pH, electrode potential, electrolyte medium, catalyst, etc. In this paper, we will present an idea of how the factors mentioned above will effect the electrochemical reduction of CO2 to Oxalic acid. INTRODUCTION. CO2 is thermodynamically quite stable, as shown by its highly negative heat of formation. Thus, it is expected that the formation of any useful chemical from CO2 will require the input of at least as much energy as geological sequestration. However, to be more effective the resulting economic value of the chemical need only pass the cost of the additional energy required beyond geological sequestration. This lends itself to two extremes: one where the quantity of energy required is low and one where the economic value of the additional energy is low. It is expected that CO2 can be reduced via electrolysis to several compounds. Of particular interest are formic acid, oxalic acid, methanol, ethanol, formaldehyde, and carbon monoxide (as a component to syn-gas). These chemicals have been reported as electrolytic products previously in literature and have considerable potential for application. EXPERIMENTAL Electrocatalytic Production of Oxalate from CO2 We are using membrane electrolysis cell to produce oxalate from CO2. A membrane electrolysis cell is a 2-chamber electrolysis cell where the chambers are separated by a selectively permeable membrane. To produce oxalate, a cation exchange membrane (which selectively exchanges cations) was used. Previous literature suggests that in the cathode chamber an organic electrolyte, such as tetraethylammonium perchlorate or tetraethylammonium bromide in dimethylformamide, are preferred3. In the anode chamber, a sodium hydroxide solution water is used. Carbon dioxide is then bubbled into the cathode chamber as a current is applied.

Jan 1, 2019

By A. Halim, A. Martikainen, S. GYAMFI

This paper outlines a unique case of the development of strategies to reduce ventilation and heating costs in Konsuln iron ore mine in northern Sweden. The mine, located just south of Luossavaara-Kiirunavaara Aktiebolag’s Kiruna iron ore mine, was developed as a test mine from 2018-2020 for the Sustainable Underground Mining (SUM) project. Besides functioning as a test mine, Konsuln also contributes to ore production. The existing mine ventilation system was designed for the current production rate of 0.8 million tons per annum (Mtpa). There is a plan to increase this rate to between 1.8 and 2.0 Mtpa.

Dec 23, 2021

By J. Franko, M. S. Klima

Wet-drum magnetic separators are used extensively for upgrading iron ore and for magnetite recovery in dense-medium separation circuits. In this study, the performance of a continuous, laboratory wet-drum magnetic separator was evaluated both with and without the application of ultrasonic energy when processing dense medium slurries. Test variables included magnetic-to-nonmagnetic ratio, solids concentration and nonmagnetic material. The results indicate that, under certain conditions, the purity of the magnetic material increased after ultrasonic treatment. Key words: Ultrasonics, Wet-drum magnetic separation, Iron ore

Jan 1, 2003

By P. Moyo, S. Dixon, R. Norcross

The separation and recovery of copper from cyanide solution has been investigated since the early 1900s. The precipitation of copper using sulfide ion was patented in 1911 by Williamson, published by Leaver & Woolf of the USBM in 1931 and Cyanamid in 1960s. The current practice of sulfide precipitation is used in various processes such as “SART" for cyanide regeneration and copper recovery. The precipitation of copper sulfide requires the pH of the clear solution to be in the range of 4-6. The precipitated copper sulfide can be sold to smelters. Alternatively, copper cyanide can be precipitated from clear solutions in the pH range of 2-3. However, selling copper cyanide is challenging because of its cyanide content. Past work has focused on the use of boiling sulfuric acid to convert copper cyanide to copper sulfate as published by Seracini in 1991. This paper describes a simple process to convert copper cyanide to copper oxide using sodium hydroxide at ambient temperatures. The cuprite can be sold to smelters or used as a feed to an electrowinning circuit to produce copper cathodes. The process provides an effective method to recover copper from cyanide solutions with a lower capital requirement.

Mar 2, 2022

By Dae S. Young, Steven F. Hoerger

The geostatistical method of indicator kriging (IK) was extended to analyze two-dimensional distributions of rock joint orientations. The IK method provides a non-parametric approach for spatial analysis of local probability distribu- tions. By taking into account the spatial correlation of rock joint outcomes and the relative geometry between estimation unit and samples, the IK method provides optimum, spatially conditioned estimates. The estimation method was tested by comparing distributions of actual mapped rock joint orientations with their corresponding kriged estimates. The comparisons show the unbiasedness and accuracy of the non-parametric approach for estimating local probability distributions.

Jan 1, 1986

By J. E. deMasi

Over the past 12 years, Exxon Coal U.S.A., Inc. has shipped over 150 million tons of coal from two mines, Rawhide and Caballo, located in the Gillette, Wyoming, area. These mines are operated by The Carter Mining Company, a division of Exxon Coal. Shipments have moved to more than 25 electric utility plants in the west, midwest, southwest, and south. The customer plants have represented a wide variety of configurations, sizes. design criteria, emission standards, and operations in different parts of the country. We have learned a great deal about the performance of Gillette area coals in utility power plants during this period. This paper covers some of the highlights of Exxon&apos;s experience with these coals in customer plants. I will focus specifically on things mining engineers may be able to do to make the product better for the customer&apos;s use.

Jan 1, 1989

By John W. Amos, John A. Christophersen

The Deister No. 7, "77" and "88" Coal Washing Tables have been used by the coal industry in the cleaning of finer sizes of coal (-1/2") since washing of coals became necessary. This paper will deal with the in-plant use of the CONCENCO "88" Deister Coal Washing Table, along with a brief description of the Deister Refuse Superscalper. Efficient in-plant operation of the Deister Coal Washing Table can be accomplished by the adjustment of six basic variables. These variables are: 1. Headmotion 2. Feed 3. Riffle Pattern 4. Dressing Water 5. End Elevation Adjustment 6. Side Tilt Adjustment VARIABLE NO. 1 HEADMOTION The reciprocating movement of the "88" Table is developed within the headmotion entirely by rotating eccentric weights. Four parallel shafts each carry pairs of eccentric weights (Figure 1-A). The shafts are geared together with gears of 2 to 1 and 1 to 1 ratios, so that the two shafts in vertical alignment which carry the small eccentric weights operate at twice the speed of the other two shafts. The other two shafts are also in vertical alignment with each other and carry large eccentric weights. As power is supplied to one high-speed shaft, once each revolution the forces produced by the large eccentric weights are reinforced and then opposed by the small eccentric weights in a horizontal plane. The direction of movement of the table decks is reversed much more sharply at the forward end than at the backboard end of the stroke, causing material to move toward the refuse end of the table. Because in the vertical plane all centrifugal forces oppose each other and cancel out, there is no vertical movement and virtually no impact to the support steel. The "88" Coal Washing Table is suspended by wire-rope cables from three overhead steel beams, and operates with a perfectly uniform and exact differential motion curve in every stroke (Figure 1-B). The decks, being attached to the headmotion, are reciprocated in a parallel line from the head- motion to the refuse corner at speeds varying from 260-300 strokes per minute. Both length of stroke and speed are set at the factory for the coal characteristic desired and should not be changed. A 3 HP motor is mounted on the top of the headmotion and uses 3 V-belts to transmit driving power to the headmotion. The headmotion must be kept running on a horizontal plane. Punch marks are provided on the side and end of the main frame for use in leveling the motion (Figure 1-C). In leveling the motion, the work must always be done with two cables. To level the long side of the headmotion both front or both rear cables are raised or lowered to bring motion back to level. To level side to side, both right side cables or left side cables are raised or lowered to bring motion back to level VARlABLE NO. 2 FEED When tabling different size coals, each deck of a "88" DIAGONAL-DECK Coal Washing Table will handle feeds as described in figure 2-A.

Jan 1, 1988

By Gordon M. Pugh, David G. Rasmussen

INTRODUCTION Square-set timbering of stopes developed from stull support methods because veins too wide for stulling were being mined. In general, the void caused by the stoping of the ore is filled with a system of interlocking timbers. Timber framework supports the wall rock, the mining operations, and provides access. A timbered stoping method can be used in all widths of veins at any dip. The timbering can be normal and parallel to the planes of the walls or at angles to these planes. Irregularly shaped ore bodies can be worked by timbered methods. Pinching or swelling of the vein will not adversely affect the method. Timbered stoping is especially advanta¬geous where weak ground is encountered in the vein or the wall rock. The ground is unsupported only until timber sets are stood. These stopes can be filled with sand or waste when desirable. The customary method of developing a square-set timbered stope with haulage drifts above and below and timbered raises on each endline is shown in Fig. 1. The drifts are timbered the full stoping length. The raises have two compartments with the manway and timber slide in one compartment and the chute in the other. The drifts and the raises cannot be widely spaced as handling timbers is an important consideration. Stoping can begin immediately above the drift timber and continue in both directions and upward from the raise. Breasting down each blast round for only one timber set laterally is the common practice. The blasted ore falls to a lower floor where it is slushed or trammed to the chute. Drilling can proceed on the upper floor while broken ore is being removed from the stope. As shown in Fig. 2, square-set timbering may be used in cut-and-fill stopes to support the back and walls until fill is added. There are various ways of developing an ore block for timbered stoping. Fig. 3 depicts the situation for the main haulage in the vein with an intermediate drift separated from it by a sill pillar. The ore is slushed into the chute connecting the two drifts. The situation in Fig. 4 is identical to that in Fig. 3 except that no sill pillar is used. In Fig. 5, the haulage drift development is done in the footwall with crosscuts driven to intersect the ore body. The intermediate drift development is above the crosscuts with a minimal sill pillar. The main bottleneck in timbered stoping is in the timbering process. Drilling in the stope is generally held up while timbering is done. Two or three men are re¬quired to do the timbering and an additional one or two men are needed to transport and raise or lower the tim¬ber. Good organization is essential to timbering. Skill must be exercised in standing the timber to support the ground and still maintain good production. COSTS AND PRODUCTIVITIES Development and stoping costs are presented in Tables 1 through 7 for the situations in Figs. 3 and 5,

Jan 1, 1982