Search Documents

By J. Y. Hwang

Sands are utilized to make molds for metal castings in the foundry industry. Approximately a half ton of sand is disposed of for each ton of metal cast in this country. In Michigan, annual sand disposal amounts to about one million tons. A process has been developed in this study to reclaim sands from a steel foundry. Physical separations are utilized in conjunction with other operations (such as the removal of binder, metal, spruce, washes, etc.) to yield silica and chromite sands with desirable molding properties. Several different separation methods, including electrostatic, magnetic, and various gravitational approaches have been examined. Experimental results are presented. The applicabilities of these separation methods are discussed.

Jan 1, 1992

By E. Galán

The largest Spanish kaolin deposits formed on granites occur in Galicia (NW Spain) due to a widespread kaolinization of Variscan granitoids. This paper provides insight of the origin of this kaolinization process on the basis of a mineralogical and geochemical study carried out in two kaolin deposits, presently mined to be used in the paper industry. Mineral composition of the deeply kaolinized rocks is dominated by well-ordered kaolinite with minor quartz, K-feldspar, mica (illite/muscovite), locally gibbsite, and traces of resistant accessory phases (rutile, ilmenite, zircon and monazite). The content and structural order of the kaolinite decrease with depth. Kaolinite formed by extensive replacement of feldspars (plagioclase). Differential mobilization of major and trace elements during kaolinization has been inferred by using a mass-balance approach. Significant amounts of Na, Ca and minor Mn, Sr, P and U were removed from incipiently leachable minerals (plagioclase and apatite), and K, Rb, Cs and Ba were released from K-feldspar and mica. On the contrary, Ti, Zr, Th, Hf and the REE are retained in the resistant trace minerals that are concentrated in the fine fractions of the kaolins.

Jan 1, 2010

By John Greenhalgh, Benoit De Rivaz

"1.INTRODUCTIONThis paper is based on the Lee Tunnel project, which is part of the Thames Water’s Tideway Project.The client Thames Water has employed a Joint Venture of Morgan Sindall/Vinci Grand Projets and Bachy Soletanche to undertake the design and construction of the project under the management of CH2M Hill at a value in excess of £635 million ($990 million). The 3 main elements of the tunnel project are the permanent lining to the shafts, the precast segmental lining, and the secondary tunnel lining. All 3 are reinforced with different types of Dramix steel wire fibers and each element will be described in this paper. This paper will explain the basic structural design of FRC (Fiber reinforced concrete) based on the post cracking residual strength and will describe all the steps of this project, the testing program realized to support innovative design and the main technical learning point. 2.BASIC CONCEPT OF STRUCTURAL DESIGN OF FRCStructural design of FRC elements is based on the post-cracking residual strength provided by fiberreinforcement. Other cases, like early age crack-control or fire resistance, are considered non-structural use of FRC. For structural use, a minimum mechanical performance of FRC must be guaranteed. Fibers can be used to improve the behavior at SLS (Service Limit State) since they can reduce crack spacing and crack width, thereby improving durability and they can be used to improve the behavior at ULS (Ultimate Limit State) where they can partially or totally substitute conventional reinforcement in most conditions. In the design process, the definition of the performance expected from the material is a key factor and the mix-design of the material has to be optimized for the required structural performance.2.1 Testing Method In order to ascertain the structural requirements requested for the FRC segments, preliminary testing on samples will be required and the effectiveness of the proposed solution will also be assured by the testing of full scale specimens. Structural design of FRC elements is based on the post-cracking residual strength provided by fiber reinforcement. For structural use, a minimum mechanical performance of FRC must be guaranteed. Nominal values of the material properties can be determined by performing a 3-point bending test on a notched beam according to EN14651 (figure 1) or by performing the ASTM C1609 beam test:"

Jan 1, 2016

By w. Chruscielewski, T. Domanski

INTRODUCTION Concentration of radon 222Rn and its decay products occuring in the Polish mines of metal-ores call for the necessity of systematic radiation control /Do8la/ both of the working environment and of the miners' personal exposure. The attempts at introducing a system of radiological protection in mines, similar to the ones existing in X-ray or isotope laboratories, took several years and consisted of development of the methods for control of concentration of radon and its progeny in the air, as well as the methods for measuring individual exposure. It was accepted that the assessment of both transient concentration in the air and of personal exposure are basic elements of the control system, which should be implemented independently of each other. Concentration measurement serves to detect and to determine those areas in mines where there is intensive radon emanation, and where current control of the effectiveness of technology introduced to deacrease the concentrations is necessary; personal dosimetry results in the assessment of the actual exposure of miners to radiation. PRINCIPLES OF THE SYSTEM The assessment of working environment is based on concentration measurements of the potential radiation energy of radon alpha decay products. Decentralized assessment is carried out by the special dosimetric service operating in each mine. Dosimetrists are equipped with portable radiometers, type RGR-11, made by the institute of Nuclear Research, Warsaw. The radiometer is presented in Fig. 1. Measurement of filter activity is performed automatically according to Markov's method /Ma62/ or any other method. Simultaneously to potential energy measurement the dosimetrists are measuring the dust concentration in the air and ventilation rate. Ventilation service looks for correlation between those indices and the concentration of radon daughters in the air. Derived Air Concentration /DAC/ for concentration assessment was accepted to be 6.25 10-6 Jm-3 /0.3 WL/ according to ICRP recommendation /Publication No. 24/ /ICRP77/. If environmental measurements reveal potential energy concentration exceeding the value of 0.3 DAC at working places, the miners employed there are subject to individual control of personal exposure. Individual exposure measurement is carried out centrally by the Institute of Occupational Medicine in [Lodz] for all metal-ore mines. Miners who are to be included in the control scheme are referred by a mine management to the Institute where they are registered and assigned a dosimeter. A passive dosimeter with

Jan 1, 1981

By Byron R. Berger

Epithermal Ag-Au deposits form at low to moderate temperatures in near-surface environments. Historically, these deposits have been the source of high-grade ores. Increases in the market prices for gold and silver make lower-grade ores economically viable when available in large tonnages. Both the high-grade and bulk-tonnage ores are a consequence of the same processes, and general models of epithermal systems can be useful in the search for new precious-metal resources. A detailed study of deposits at Round Mountain, Nevada; Balei, Russia; Creede, Colorado; Guanajuato, Mexico; and Chanarcillo, Chile, indicates that the hydrodynamics of the fluid systems as determined by fracture geometries, the permeability, and composition of the host rocks are the key factors in the creation of both high-grade and bulk-tonnage epithermal deposits. End-member models that explain the range of observed deposit characteristics are: (1) the hot-springs deposition model; (2) the stacked-cell convection model (where mineral deposition occurs laterally along the interface of two partially separated fluid reservoirs); and, (3) the closed-cell convection model (where deposition occurs in vertical zones due to the relatively unimpeded vertical flow of hydrothermal fluids). Boiling and fluid mixing appear to be agents of precious-metal deposition with the self-sealing of the hydrothermal system being an important adjunct to boiling. Imaginative application of model concepts in exploration has led and can lead to the discovery of new high-grade and/or bulk-tonnage precious-metal deposits.

Jan 1, 1982

CVRD was established on June 01, 1942, during the Second World War, through an agreement between Brazil, the United States and the United Kingdom, to produce 1.500.000 tons/year of iron ore from Itabira mines in the State of Minas Gerais. As a result of several circumstances and political problems (the end of the 2nd World War reduced the Anglo-American support to its development and implementation), the venture just reached the originally targeted production 10 years after its establishment, operating within a mine, railway and port integrated system. Currently, this operational system from the South of Brazil owns mines in the State of Minas Gerais with an annual capacity of approximately 65 million tons, 900 km of railways, of which more than 500 km is a double line railway, six pelletizing units and the Port of Tubarao for ships with large carrying capacity.

Jan 1, 1994

By S. P. Chong, Peter V. Avotins

The iron and steel industry continues to operate at depressed production levels due to the low level of demand for steel and foundry products. Crude steel production in the Western world dropped by 13.7% from 459.3 Gt (506 billion st) in 1981 to 396.4 Gt (437 billion st). The reduction was particularly severe in North America where the industry suffered a loss of 37.3% from 123.6 to 77.5 Gt (136 to 85 billion st). This reduced level of production severely affected iron ore and agglomerates output. Substantial curtailment was made in both sintering and pelletizing plants to meet reduced demand. The pressure on these plant operators shifted from quantity to quality. With energy cost becoming an ever increasing part of production costs, conservation was a major area of emphasis. Iron Making Sinter has continued to be the favored burden for blast furnaces overseas. As hot metal production declined and excess sintering capacity developed, many of the overseas operators that have been using pellets found it advantageous on hot metal production cost to increase the ratio of sinter at the expense of pellets. This was the case despite the depressed price level of pellets in the world market. In North America where pellets have been the predominant burden material-mainly because it is necessary to pelletize the fine grain iron ores available domestically-there was also increased interest in sinter usage. Bethlehem Steel Corporation's 13.6-m (44.5-ft) furnace at Sparrows Point experimented with a burden with more than 70% of sinter during the second half of the year and indicated some favorable results as compared to its previous 50% super flux sinter and 50% acid pellet burden. The blast furnace operators continued to press for improved burden quality. In addition to the emphasis on the importance of burden chemistry and quality, uniformity, much emphasis was placed on improving reducibilitiy and high temperature metallurgical qualities. These burden properties were recognized to hold further promise in reducing fuels rates. Sintering With reduced consumption caused by the cutback in hot metal production, many sinter plants sat idle while others operated at greatly reduced rates. The deemphasis on production in many plants allowed them to experiment with various means to reduce operating costs. The most notable action was the introduction of low cost South American pellet feed fines into the sinter ore mix. These feed fines, which are finer than 150 µm (100 mesh) ore, were previously thought to be too fine for sintering. However, when the full production rate is not required the use of up to 40% in the ore mix was reported to be successful with the aid of burnt lime and adequate premixing and granulation of the sinter mix before sintering. The emphasis on quality and tighter cost control also has resulted in a further breakthrough in sintering technology. It was recognized that good feed preparation-including selection of compatible ores, good blending, good pseudo-particle formation, additive size control increased bed depth, and closed control of the sintering bed heat pattern-could allow the production of high quality sinters with much lower heat input and FeO level. Bed depth of more than 600 mm (23.6 in.) was practiced in a number of operations. Total heat input of better than 1.3 GJ/t (290,300 kcal per st) has been achieved. Kawasaki Steel's Chiba Works has also achieved a 5.3% SiO2 in the sinter with good quality. The low heat input approach allowed production

Jan 5, 1983

By Stanislaw Siewierski

One of the major problems in the exploitation of deep copper ore deposits in the Legnicko-Glogowski Copper Field is ground control and, in particular, roof control of the headings. The depth of copper deposits ranges from 600 to 1200 m. The parameters of ore-bearing rocks and the surrounding rocks show considerable variance of strength properties along the mining thickness (Fig. 1). The roof of the openings exploitation headings consists of dolomite-calciferous rocks. The roof strata consist of layers, the thickness of which vary from several centimeters to 0.6 m (sometimes to 1.0 m). These strata differ in strength and are characterized by igneous and sedimentary discontinuities. On the basis of studies in structure, properties and geological mining conditions of the roof strata in Polish copper mines, the method of roof classification has been developed. (1) This method uses the stability index "L" of the roof, calculated from [ ] The value of "t" ranges from 0, l to 0,8. Based on the value of "L", four classes of the roof (Table 1) corresponding to different degrees of fall hazard have been developed. The mining of copper ore deposit is carried out by a single lift room-and-pillar mining system or a two-stage room-and-pillar system with roof caving. (3, 4). The single lift room-and-pillar mining system is most often used. It consists in working of the deposit of 2.5 to 4.5 m mining thickness, 150-350 m long mining line, consisting of parallel room faces 6 m wide with pillars 5.7 or 16 m wide. As the mining line advances, cross-cuts joining individual rooms are made, thus forming support pillars 3x5, 7x7, 5x16, and 7x16 m (Fig. 2). The two-stage system (Fig. 3) mines the deposit with rooms 6 m wide into blocks 25 x 35 x 25 x 45 m. During the second step these pillars are worked with rooms and cross-cuts into pillars about 3 x 4 to 4 x 5 m (retreat mining). The pillars are crushed just before the fall of the roof. The maximum opening of workings in the two-step system is about 10 m, i.e. one belt entry and one row of bearing pillars. In single lift room-and-pillar systems it is about 35 m., i.e. three belt entries and three rows of bearing pillars. The support of the headings consists of expansion bolts 1.6-1.8 m installed in a bolting pattern 1.1 x 1.5 m. In both systems the fall step is about 10 m, i.e. the width of a belt and a bearing pillar. The Indications of Rock Mass Pressure Individual Dog Heading Individual dog headings are set wide apart from each other in the unmined ore deposit area where there is no interaction of headings. The indication of rock mass pressure are, in such cases, limited to the deformations and damage of side walls. Radiometric studies of rock mass loosening showed that the maximum range of lifts in side-walls immediately after web was 2 m (4,5). In the course of time the cracked side rocks fall off, thus widening the heading. The morphology of side-walls is influenced by the location of the heading in relation to clump layer/tarry. This layer is characterized by a weak strength and "lubricating" properties. The location of the heading in

Jan 1, 1982

By Nicholas S. Lynn

Introduction Borne out of the need for reductions in capital expenditure and increased production, several new and innovative carbon systems have been developed for small precious metal heap leach operations throughout the United States. Perhaps the most important aspect of these systems is the carbon column. Though diverse in design, these columns can be categorized into three basic types. The first is known as the gravity flow type or Cortez type. As the name indicates, solution flows via gravity, throughout 4 to 6 columns which are arranged in a normally stepped con- figuration which is conventionally upflow in design. The second type, known as the vertical column, is an arrangement whereby flow is established through pressurization in an upward manner, throughout 4 to 6 columns in a vertically stacked configuration. This arrangement is typically intended for use with small portable heap leach operations and employs a semi-continuous mode thus preventing gravity from occurring. The third type and newest development in carbon columns is an arrangement whereby the solution flows throughout 4 to 6 columns placed in a side by side configuration and pressurized by a single feed pump (Figure 1). A unique aspect to the third type, is that the adsorb and desorb cycles are accomplished in the same column, due to a fixed carbon charge. An in-depth analysis is warranted due to numerous advantages of this arrangement, and is therefore the subject of this paper. Advantages and Variations One advantage to the third type of carbon column is the fact that initial capital expenditures and operating man- power requirements are reduced. Another advantage is that the system can be made fully portable up to a 0.0315 m3/s (500 gpm) capacity. Systems of this nature are operational at several sites. Above this flow rate, the system's portability is one which can be maintained, but disadvantages (i.e. larger diameter carbon column and greater weights) far outweigh the advantages. There are several variations in each of these systems which allow for unique operation. For example, carbon columns made highly portable, can be moved from unitized heap leach operations to central stripping facilities. Although this method has been used in Colorado, transportation of these units has been known to be quite cumbersome. If distances exceed 5 km (3.2 miles) then special front-end loaders are required. This limits heap locations to within 5 km (3.2 miles) of the central processing facility. Another example transports the carbon charge from the heap leach locations to a centralized processing facility; this method is quite effective. For the past 5 years one mine has employed this technique of transporting carbon in 907 kg (1 ton lots), in DOT containers, towed by company pick-ups. This operation uses a vertical column with a 907 kg (1 ton) carbon charge. A third example uses static carbon columns with fixed carbon charges. Carbon Adsorption System The carbon adsorption system (Figure 1) is fed by a single preg solution feed pump. This feed pump pushes the preg solution through all four to six fixed charged carbon columns, which are on line. The sequencing of the carbon columns is achieved using valves. Expansion of the carbon charge is dependent upon the carbon selected. The carbon typically used is a 6 x 12 mesh size, with a nominal flow rate of 0.00135 - 0.00138 m 3/s (22-25 gpm) per square foot of carbon, based on a 40% bed expansion. With 8 x 16 mesh size,

Jan 1, 1987

By Zhe Wang, Tichang Sun, Yongqiang Zhao, Zhengyao Li

Coal-based reduction followed by magnetic separation is a promising technology for processing refractory iron ores. Analysis of the size distribution of metallic iron particles is an effective approach for exploring the mechanisms of coal-based reduction. As metallic iron particles exhibit very complex shapes compared with nature ores, approaches for measuring and characterising metallic iron particles still remain unclear. In this study, the size of metallic iron particles was measured and characterised using manual point-counting by optical microscopy technics and image analysis. The effects of CaF2 as an additive on behaviour of the particle size distribution (i.e. mean size and cumulative frequency distribution) were also determined. Results indicate that CaF2 had a significant effect on the growth of metallic iron particles. When the CaF2 dosage increased from 0 to 8%, the mean size according to the area method increased from 9.03 to 16.28 μm, while the promotion effect gradually weakened and generated many fine metallic iron particles when the CaF2 dosage exceeded 8%. An increase in CaF2 dosage also led to cumulative distribution curves gradually shifting to the right mainly because F− can break the crystal structure of each phase during the carbothermic reduction of titanomagnetite and reduce the stability of the lattice structure, thus reducing the melting point and accelerating the growth of metallic iron grains. Compared to different measuring methods, the area method is a more suitable approach for measuring and characterising the size of metallic iron particles.

Sep 18, 2020

By C. Clark, R. Pakalnis, B. Seymour, L. Martin, R. Jacksha, M. Stepan, M. Roworth, C. Caceres

The National Institute for Occupational Safety and Health (NIOSH) is conducting research to develop safe practices for the use of shotcrete as ground support in underground mines, particularly mines operating in weak host rock. As part of this research, a rugged, portable direct tensile test system was developed for measuring shotcrete adhesion strength in underground mines. During the development of this test system, more than 185 direct tensile tests were conducted with a common, commercially available macro-synthetic fiber-reinforced shotcrete that was applied to concrete test panels using a dry mix process and machinery. The average bond strength of the shotcrete to the concrete substrate typically increased as a function of the shotcrete’s curing age, ranging from 0.44 MPa (64 psi) after one day of curing to 1.58 MPa (229 psi) after 90 days of curing. Adhesion strength increased markedly between one and three days of curing, reflecting a similar trend of increasing shotcrete tensile strength with curing time. This robust direct tensile test system can improve mine safety by providing a reliable means of measuring shotcrete adhesion strength and also supplying important information about the quality of the applied shotcrete and the competency of the underlying rock.

Jan 1, 2010

By Clement K. Chase, J. A. Eisele, Paul D. Chamberlain, Terry Laverty, Lee Rice, Larry Sevenker, Albert G. Law, Daryl Tweeton, John Peters

"Name your poison," wrote Forbes, Jan. 3, 1983, in an article describing the plight of much of the mineral industry as it entered the new year. "To ask which (mining) segment is better these days is almost like asking which of several stones would make a better life preserver." "The scene has seldom seemed darker or apparently less promising," said the Mining Journal in June 1982. And the Northern Miner described the year as the third in a "3-year drought which has completely dried up (company) coffers." Thus, 1982 became the worst year for much of the mining industry since the Great Depression. Low prices, commodity surpluses, output reductions, layoffs, temporary and permanent closures, and financial losses made headlines as the general recession continued to hurl blows at an industry facing strong foreign competition, increased government regulations, and plummeting market demand. At fault were tight US monetary policies and the resulting high interest rates that, while forcing inflation to slow, also threw the economic wheels of the country into reverse gear. Automobile production, housing starts, consumer durable sales, and capital spending all fell dramatically. US industrial production fell about 8.5% in 1982, with the GNP dropping by 1.7%. Production Value Not a single mineral escaped this recession. According to the US Bureau of Mines, US nonfuel production value dropped for all but four out of 21 metals and 14 out of 44 nonmetals. Production quantities increased for only gold, lead, and zirconium among metals and for only six nonmetals. Total nonfuel mineral production value dropped a whopping 21% from 1981 levels, the largest decline since 1938 and the first since 1971. Production value was estimated at $20 billion. Metal commodities showed heavier losses than nonmetals-37% vs. 12%-because of their link to depressed automobile and construction industries. Prices From peaks in early 1980, prices of precious and base metals, ferrous and nonferrous metals, and virtually every mineral dropped to 30-month lows in June 1982. Gold dropped to $9.64/g ($300/oz) compared to a high of $27/g ($850/ oz). Silver was quoted below 164/g ($5/oz) versus a $1.61/g ($50/oz) high. Copper was offered at a five-year low of $1.22/kg (55.5¢/lb) compared with a high of $3.30/kg ($1.50/lb). Lead went for 53¢/kg (24¢/lb) versus $1.21 (554). Nickel begged for buyers at $4.19/kg ($1.90/lb) compared to a high price of $7.72/kg ($3.50/lb). Molybdenum was available at or below $8.82/kg ($4/lb), down from a high of $44/kg ($20/lb). Cobalt went for $11/kg ($5/lb) versus $55/kg ($25/lb). Adjusted for inflation, increased currency costs, and currency devaluation, many of these prices are the lowest reached in decades. Financial Profits & Losses Low prices severely impacted companies' earnings, turning profits into sometimes disastrous or fatal losses. Robert Norton, director of the US Bureau of Mines, noting there has been a recession in the mineral industry for years, said, "Profit rates as related to invested capital have been considerably lower (for mining) than those of other industries. Mineral industry profits have been subject to greater cyclical swings and debt equity ratios have been significantly greater than

Jan 5, 1983

By John J. Stetler

Introduction Samarco Mineracao S.A. is a Brazilian corporation jointly owned by S.A. Mineracao da Trindade (SAMITRI) and Utah International Inc., with 51% and 49% interests respectively. Headquartered in Belo Horizonte in the state of Minas Gerais, Samarco owns and operates an open-pit mine capable of producing 10 Mt/a (11 million stpy) of iron ore; a concentrator rated at 7 Mt (7.7 million st); a 12-Mt (13.2-million st) capacity pipeline transportation system; a 7 Mt (7.7 million st) filtering and pelletizing plant; and a harbor facility. The mine, concentrator, and initial pipeline pump station are located at Germano, near the town of Mariana, about 300 km (186 mi) north of Rio de Janeiro by air. The pipeline terminal, pellet plant, and harbor are at Point Ubu, 70 km (43 mi) south of Vitória the capital city of Espirito Santo State, and about 300 km (186 mi) by air east of the mine. The 396-km (246-mi) pipeline uses 508-mm (20-in.) pipe except for a 53-km (33-mi) section where 457-mm (18-in.) pipe is used to absorb and control slack flow through increased velocity in one of the areas along the route. Iron Ore Slurry The hematite iron ore concentrate produced at the Germano plant is processed by grinding the average 53% run-of-mine itabirite iron ore to -150 µm (100 mesh) for gangue liberation. It is treated further by cyclones to remove the 10 µm (1250 mesh) slimes to prepare the ore for flotation. During the multistage cationic flotation operation, the silica is reduced to make low silica (-0.9%) concentrate for the direct reduction (DR) iron-making process or to make normal silica (-3.5% +2.5%) concentrate for the blast furnace (BF) iron-making process. The concentrate then is reground further to meet the particle size requirements for pelletizing. The reground hematite concentrate is screened in closed circuit with the regrind mills for close control of the maximum particle size, not to exceed 3.5% +75 µm (200 mesh) for pipeline wear protection. Thickened concentrates at 70% solids are pumped to four 5-kt (5,510-st)(dry) agitated slurry storage tanks that hold the feed before it goes to the first pipeline system pumping station. Pipeline Capacity The pipeline system was designed to transport 12 Mt/a (13.2 million stpy) at 65% solids with an average minimum safe operating velocity of 1.5 m/s (5 fps). The pipeline will transport 5 Mt (5.5 million st) in 1982. The system, therefore, is moving the slurry in 13-kt (14,330-st) batches, dispatched at intervals to move 20 kt/d (22,050 stpd). In operation, the pipeline has exceeded its 93% availability design factor. Pipeline Facilities Pump station No. 1 is located at the Germano minesite 1 km (3,330 ft) above sea level. It has the following principal equipment: • four 5 kt (5,510-st) (dry) agitate slurry storage tanks; • two centrifugal charge pumps (one stand-by); • a 217-m (712-ft) safety loop; • seven mainline positive displacement triplex plunger pumps (189 m3/h, or 832 gpm, at 14.9 MPa, or 2,162 psi, maximum output pressure); • four corrosion-erosion spools; • a control and command center. Operation The output at pump station No. 1, with 66% solids, is pumped 151

Jan 10, 1982

By William P. Lorenz

The paper describes a uranium by-product recovery plant operating within a copper leach, solvent extraction, and electrowinning circuit. The operation is unique because it is integrated into the main process stream of the copper circuit The plant processes 1408 m3/h of copper solutions containing about 10 mg/L of uranium. An Eluex type process was selected due to its compatibility with the copper leach plant. The paper includes an overview of the copper circuit

Jan 1, 1983

By Peter Hall

The need for large volume covered storage has increased drastically in the last ten years. Increased world demand for such products as thermal coal, potash, metallic concentrates, etc., availability of land for large open storage and environmental issues have brought about this need. This paper discusses briefly demand, environment, types of covered storage and the Alternative Storage System "Eurosilo", a proven system for storage of dry bulk mateials in units up to 100,000 m3.

Jan 1, 1982

By S. Hartman

The Escalante Silver Mine in Southwest Utah produces an average of 71.000 kg (2.3 million troy ounces) of silver dore annually. Precipitates from a cyanide leach circuit are treated by either acid leaching prior to fusion or a direct fusion with nitre. Process development, plant experience, and a comparison of both methods will be discussed. Plant experience from the custom treatment of a gold/silver precipitate containing matte producing elements will also be covered.

Jan 1, 1989

By J. Tavares

It is no mystery why the mining industry has such lofty safety standards. In dealing with Mother Nature and gravity, the combination of the two can create significant hazards from high wall and tunnel collapses to huge landslides. The loss of production from a major disruption could be enormous. The price tag on the loss of human life is immeasurable. The evolution of geotechnical instruments and software has been ongoing for years. But the biggest innovations have occurred during the era of cell modems, internet, and wireless networks, allowing for real time data and alarms to be delivered globally anywhere and anytime to one?s computer, laptop and smartphone. Yet in some ways you can thank the urban construction projects for developing much of the technology in use by today?s mines. Due to the density of population and the billions in dollars of structures and infrastructure in cities throughout the US and the world, urban projects have faced intense scrutiny for years. Out of this scrutiny was born the necessity of real time automated monitoring of instrumentation and sensors, a defence against catastrophic failures, and real time early warning systems through alarms that can and do saves lives. It is also possible to identify areas of concern with subsequent remediation prior to failure.

Feb 23, 2014

By Dean D. Turner

Exploration geochemistry requires computer processing for quick and efficient reduction and interpretation. An easy to use microcomputer based geologic workstation fulfills this need and allows the geologist to independently process geochemical data. Functions necessary for geochemical data processing are: 1)Digitizing; 2)Communications; 3)Data base management; 4)Statistical analysis; 5)Mapping analysis; and 6)General purpose applications (ie: word processing). A geologic workstation that can perform these tasks will yield significant advantages in processing and interpreting geochemical data.

Jan 1, 1987

By E. L. Smith

The development of larger size flotation machines, which started in the 1950's and 1960's, is still proceeding. The largest mechanical flotation machines avail-able today have unit volumes in the range of 38.2 to 43.9 M3 (1,350 to 1,550 cft). Designs for mechanical flotation cells of unit volumes as large as 70.8 m3 (2500 cft) are available. The development of these "giant" flotation machines has been and continues to be motivated by the increasingly critical forces of higher energy and capital costs, decreasing ore grades, and lower (real) prices for the products. As an expansion of a previous publication, this paper reports the further development of an improved mechanism for these large flotation machines. The starting point in the develop¬ment of a new mechanism was the identification of design and performance features of existing machines where improvements were desirable. The result of this work was a mechanism which s is an improvement over existing designs. This new design is characterized by an efficient overhung stator and a vortex profile rotor. The overhung design of the stator removes unnecessary and undesirable baffling in the lowest parts of the tank, while maintaining a quiescent froth layer. This results in lower power consumption and better pulp circulation and solids suspension. The vortex profile rotor acts as an efficient pump, with higher pulp recirculation rates as evidenced by the increased air dispersion capabilities, good solids suspension, and low power consumption.

Jan 1, 1983

By Nathaniel Arbiter

The development of flotation machines since the first industrial use of the process can be divided into three stages. The first, up to about 1930, was marked by diversity in the means for contacting floatable mineral with the air/ water interface and for generating the interface, as well as in cell design. By 1927 Taggart (1) could list 170 patents covering flotation cells, and he mentioned dozens which were or had been in operation. He divided cells into eight categories according to design, type of separating interface, and where in the cell and how separation took place. These were: (1) Film or skin flotation with wet or dry oiling of surfaces; (2) pulp body process with bubbles generated chemically by pressure reduction, by vacuum or by boiling; (3) agitation-froth processes involving local supersaturation with air; (4) bubble column; (5) pneumatic; (6) cascade; (7) subaeration; and (8) combination and miscellaneous types and processes. Most widely used then were the agitation-froth, sub- aeration, pneumatic types. By 1943 a significant reduction in categories had occurred to the two main divisions of mechanical and pneumatic cells according to whether agitation and aeration were (a) by an impeller with or without compressed air, or (b) by compressed air alone. Cells at that time were still relatively small; the Morenci Concentrator completed in 1942 used 432 1.7m3 (60 cu ft) Fagergrens for roughing 45,000 and later up to 55,000 t/d.

Jan 1, 1979