Search Documents

By R. Thorpe, M. Dosbaba, A. Kopriva, A. Niiranen, J. Ruokanen

"Automated Mineralogy (AM) is an important diagnostic tool in flotation plants as it adds ore and particle mineralogical properties to traditional mass and chemical data. AM is used in project development, for future ore studies and for diagnosing concentrator operations. With the exception of operations who own central laboratory or on-site systems, the use of AM is often limited to the analysis of a comparatively small set of samples. Metrix Plant Technologies has partnered with TESCAN to integrate TIMA AM technology into the implementation of Performance Assessment Campaigns (PAC). Routine daily composite samples from the mill are analysed mineralogically on a size-by-size basis over several weeks. All the relevant metallurgical, process control and mineralogical data is combined into a single large database for mass balancing and interactive examination. This paper describes the implementation and results of a PAC at the Agnico Eagle Kittilä gold mine in Finland. Although challenging, the addition of mineralogical data as dependent variables in multivariate analysis leads to a much deeper understanding of the root cause effect of events driving the flotation performance. INTRODUCTION TO STUDY The Kittilä mine, owned by Agnico Eagle, is Europe’s largest primary gold mine, with annual production of approximately 180,000 Oz. The operation is located in Lapland in northern Finland, and is currently expected to operate until 2035. The location of the operation is shown in Figure 1. Historically, the mine was an open pit, although in recent years ore is sourced solely from underground operations. The processing plant features crushing and grinding, followed by carbon flotation and sulphide flotation. Carbon concentrate is a waste stream, and sulphide concentrate reports to pressure oxidation (autoclave) and CIL circuits for gold extraction. The final flowsheet is shown in Figure 2. Following commissioning in late 2008, the operation achieved commercial production on May 1st 2009. Gold recovery in flotation gradually increased to a 92-96% range at a throughput of ~3500-4000 tonnes per day. In late 2014, the operation commissioned a plant expansion to ~5000 tonnes per day. Following a commissioning period, the operation stabilised with recoveries in a 90-94% range, which over any given period was determined to be ~2% lower with statistical significance. The trends from start-up of gold recovery in flotation and throughput are shown as follows in Figure 3. In early 2016, Agnico Eagle Kittilä mine, along with Agnico Eagle Technical Services (AETS) partnered with Metrix Plant Technologies and TESCAN, to perform a Performance Assessment Campaign (PAC) at Kittilä, involving automated mineralogy on five key streams at Kittilä on 40 days selected from a 50 day period between February 15th and April 4th 2016, when plant operations were stable. In addition to the mineralogical data, metallurgical and operational data were pooled into a single, powerful database to explore opportunities for the operation to improve recovery in a sustained manner, ideally to the levels pre-expansion."

Jan 1, 2017

By J. A. Holtkamp

Environmental regulation in Mexico has matured dramatically and effectively in the last decade. The gap between environmental regulation in the United States and Mexico is rapidly narrowing, so much so that it is no longer necessarily less burdensome to operate in Mexico from a regulatory perspective. This paper is intended to give a general overview of the system of environmental regulation in Mexico. The actual application of Mexican laws and regulations governing the environment to a specific operation will require a much more detailed review of the applicable environmental standards.

Jan 1, 1994

By C. R. Tinsley

In maybe the world's first in a mine project financing, a US $55 million Rehabilitation Indemnity was given on behalf of the banks in a US $250 million loan to develop the Ranger uranium mine, Northern Territory, Australia. The basis of the financing was an estimate of removal of the tailings and replacement into the pit. The Indemnity was amortized by a sinking fund from the mine's revenues. Such a concept could be valuable for mineral developments in sensitive areas or jurisdictions such as British Columbia or Alaska.

Jan 1, 1992

By Linda Frederick

In July 1997, Krupp Canada obtained the contract to design and supply the conveyor system for Chile's Los Pelambres copper mine expansion project. Progress on the overland conveyor system is currently on schedule. It is a challenging task to convey copper ore from an open-pit mine located on a mountain site 3,000 m (9,840 ft) above sea level down 1,300 m (4,265 ft) to the processing plant at the valley floor below. The Los Pelambres conveyor system moves copper ore at a rate of 8.7 ktlh (9,600 stph) and at a speed of 6 ml sec (1,180 ftlmin) for 12,750 m (41,830 ft). The distance is divided in three conveyors, each 1,800 mm (71 in.) wide. The largest conveyor is 6 km (3.7 miles) long. To protect against avalanches and rockslides, the conveyors run through a 12-km- (7.4-mile-) long tunnel system. The lowest of the three conveyors is equipped with a shuttling head end. With this, the conveyor discharge point can be moved back and forth by 100 m (330 ft), allowing it to build up a longitudinal stockpile at its end. To meet the extreme design parameters, the limits of conveyor design had to be pushed to record-setting marks. For instance, the ST-7800 steel cord conveyor belt is the strongest belt ever installed in a conveyor system. A total drive power of 25 MW (33,535 hp), consisting of 10 2.5-MW (3,352-hp) drives, is included in the design plans. In loaded condition, the electric motors act as generators and feed electric energy back into the power grid. The motors are controlled by variable frequency inverters that provide an infinite adjustment of motor speed. This technology allows starting and stop- ping the conveyors precisely along predetermined acceleration and deceleration ramps. This is done so harmful belt jerking and stress waves can be avoided.

Jan 1, 1999

By P. James

"INTRODUCTION High sulfate (SO4-2) levels often occur in MIW (mining influenced water) either as the result of oxidation of sulfide minerals exposed by mining activity or by deliberate addition – commonly by sulfuric acid (H2SO4) use in hydrometallurgical leaching activities. Increasing regulation of sulfate discharge is creating new pressure to treat or mitigate sulfate release to prevent its entry into the environment. Current treatments include precipitating as gypsum during lime treatment, filtration separation using membranes such as reverse osmosis and nanofiltration technology, and biological elimination via methods like constructed bioreactors. Blue Planet Strategies (BPS) focuses on improved resource utilization targeting electrolytic treatment and waste conversion into resources and has now demonstrated that its proprietary DEMET™ (Dynamic Electrolytic Metal Effluent Treatment) platform can also remove sulfate from target streams as a byproduct of its usual primary treatment focus points of metal species elimination and/or pH adjustment.[1-6] This powerful new capability can mitigate sulfate contamination and recover the sulfate in a useful and potentially saleable form as a byproduct of improved primary treatments focused on enhancing production or treating waste. This provides a new treatment opportunity and value proposition for lowering overall sulfate consumption/addition or creating new revenue to defray conventional treatment costs. The DEMET Alternative DEMET utilizes a patented electrolytic technology platform employing proprietary dynamic high surface area electrodes in innovative configurations to achieve a variety of novel selective chemistries. DEMET‘s unique elements can yield higher processing rates at practical efficiencies, lower energy consumption, plus improved processing stability and lower maintenance requirements due to enhanced resistance to cell fouling and shorting; while also thwarting cross stream (catholyte vs. anolyte) contamination. Consequently, DEMET can provide a superior, extremely versatile, and cost-effective electrolytic treatment option where a multitude of FEED and PRODUCT stream combinations might be employed in comparison to traditional tankhouse electrolytic cells. Secondary reactions (Figure 1A) which could also occur at the cathode (plating/electrowinning, precipitation/scale formation, etc.) are controlled through process tailoring and operation parameter selection. Additionally, DEMET‘s innovative dynamic system mitigates potential fouling and electrode occlusion or shorting challenges which could occur when process particulars demand some of these secondary side reactions occur."

Jan 1, 2015

By Ernest Y. Baafi

This paper describes the results of a series of comparative studies in which polygonal, IDS, and kriging were compared for their local estimation accuracy. The specific objective of this study was to determine the impact that the particular nature of the mineralization has on the results of such comparative studies. The study was performed on simulated coal deposits and the evaluation parameter chosen was the coal thickness. For this study, many conditionally simulated deposits having different degrees of seam thickness continuity were first developed. Each simulated deposit covered an area of 30,000 ft x 30,000 ft which was, in turn, subdivided into 100 mine planning blocks of 3,000 ft x 3,000 ft in size. Thickness estimation was made for these mine planning blocks using surrounding DDH assays. In all cases tested, e.g., from a perfect continuity to a complete lack of continuity in coal seam thickness, kriging gave the best estimates among the three, followed by IDS and polygonal methods. As expected, the relative efficiency (i.e., superiority) of kriging over other estimators was highly dependent on the nature of mineralization.

Jan 1, 1982

By Martin G. Taube, Dwayne A. Lewis

Drainage improvements at O’Hare International Airport, Chicago, IL included the installation of a drainage and storm water system to control the over?ow from nearby Willow Higgins Creek. This involved construction of a weir structure at the creek and the channeling of water from the weir to a newly constructed reservoir via three, 3.7-m(12-ft) diameter, underground storm sewer lines. The sewer lines passed beneath an existing, 2.3-m (90-inch) diameter high-pressure water main, which was to remain in service throughout sewer line installation. The soil composition around the water main ranged from medium stiff clays to silty sands and sandy silts. Triple-fluid jet grouting was used to stabilize the variable soil profile beneath the water main in preparation for tunneling and installation of the sewer lines. The varying soil strata presented a challenge to the project team to establish a constant set of jet grouting parameters throughout the stabilized zone while keeping within the specified unconfined compressive strength range for the stabilized zone of 690 to 1,380 kPa (100 to 200 psi)at 28 days.

Jan 1, 2003

By A. M. Al Taweel, V. K. Kasireddy

Intensive coal cleaning usually necessitates fine grinding of the feed in order to liberate inorganic constituents from the surrounding organic matrix. This however adversely affects the ability of flotation techniques to beneficiate coal. Such difficulties are mainly attributed to the increase of particle population density, the decrease in capture efficiency, and the greater tendency of inorganic components to report with the froth. A three-pronged approach was adopted in an attempt to overcome these difficulties. The aggregative flotation technique was used to reduce particle population densities and improve capture, while unconventional spargers were used to generate a wide range of bubble sizes. Use of unagitated flotation columns allowed for the maintenance of countercurrent flows in both the recovery and washing sections. The combined effect of these parameters enabled the recovery of 92% of the carbon content of coal having an average particle size of 20.5 µ m, while rejecting 85% of the ash. This was accomplished using 2 kg of fuel oil per tonne of coal in a column 2 meters high operating at 2-3 tph/m3, a capacity which compares favourably with conventional cells.

Jan 1, 1989

By Chen L. Lin, Luis R. M. Bittencourt, Jan D. Miller

Recently research efforts have been made to obtain a high-purity gibbsite concentrate, suitable for first-class alumina refractories, from a Brazilian bauxite ore containing gibbsite (50%), quartz (35%),and kaolinite (15%). Detailed polished-section microprobe analysis was used to describe the liberation characteristics of the ore. Experimental results suggest that the kaolinite liberation characteristics can be described by King's liberation model and that only about 11% of the kaolinite is expected to be liberated at a particle size of 75 µ. Bench-scale experiments for the flotation of gibbsite/kaolinite from quartz using alkyl sulfates as collectors were particularly successful at pH 2, and under appropriate conditions a concentrate containing 93.0% A1 0 (calcined basis) was obtained 2 3 at a gibbsite recovery of about 96%. Subsequently, the more difficult separation of kaolinite from gibbsite was accomplished by kaolinite flotation from the alumina concentrate with a quaternary ammonium salt at pH 6 to produce a high-purity gibbsite product, 97.4% A12O3 (calcined basis), at an overall gibbsite recovery from the bauxite flotation feed of about 90%.

Jan 1, 1990

By R. Raitani

Five kaolin crudes from the state of Georgia in the U.S. were investigated for processability with chemically enhanced magnetic separation (CEMS) technologies developed by Cytec. The technologies used magnetic reagent alone or in conjunction with specialty chemicals to selectively agglomerate and magnetize the desired minerals (impurities) to be removed by the conventional magnetic separation equipment. All crudes indicated treatability using CEMS. Results indicated that CEMS technology could be applied to different kaolin crudes to obtain a product with titanium impurities less than 0.6% TiO2 from individual crudes. The features and benefits of the technologies were also reviewed.

Feb 1, 2012

By Bekta? Uz

In this research, geological characteristics of sand quarries around the village, Kemerburgaz Akpinar, are studied and the mineralogical, petrographical, chemical and technological characteristics (such as sieve analysis, relative density, water absorbtion etc.) of the sand samples, obtained from the area are explained. In the general area sand' quarries, being in lacustrine formations belonging to Neogen, the stratigraphic location of the sand occurences take place at high levels of these formations, geologically. All of this pattern, being under 1 mm with a ,particle dimension, it ranges from 0,5 mm in the quantity of 99 % to 0,25 mm in the quantity of 15 relative density is 2,65 g/cm3 ; water absorbtion is 0,9%. Mineralogically, the sand samples contain Quartz (84%), Feldspar (3%), Calcite + Aragonite (10%), Pyroxen+Amphibole (1-2%), Garnet+Tourmaline (0.5%), Olivine (0.1-0.5%). Besides, sand samples contain SiO2 with the quantity of above 90%. Containing Quartz at high levels for mineralogical, petrographical and chemical characteristics, Akpinar sand will be evaluated as silica sand when the carbonate mineral is removed with the method of ore preparation such as leaching.

Jan 1, 2005

By V. Svalbonas

The process of grinding mill quality assurance brings with it associated truths and myths. When the mill quality assurance process took its first great steps forward in the late 1970s and early 1980s, they were in response to the conditions existing, in our industry, at those times. In the late 1990s, we are faced with different conditions, and problems, and need fresh solutions. Yet the system developed for the early 1980s has produced no new approaches for the late 1990s, becoming instead more hardened and entrenched. This lack of development and actual resistance to research is now costing the industry significant amounts of money in late start-ups and useless scrap loss.

Jan 1, 1999

By Marie-Antoinette Dziurla, Barrie Johnson, Åsa Kolmert

Acidophilic bacteria are well known for their role in accelerating the oxidative dissolution of sulfide minds, such as pyrite. Other acidophiles, however, are able to catalyze dissimilatory reductive reactions. Bacteria that reduce ferric iron to ferrous, and sulfate to sulfide, were isolated from ARD-impacted environments and immobilised onto porous beads made of recycled glass. Column bioreactors containing colonized beads were constructed and peacolated with synthetic and actual ARD, and evaluated for their capacities to promote iron or sulfate reduction, and pH amelioration. Iron reduction did not require strictly anoxic conditions in bioreactors, and rates of up to 800 mg Fe3+ reduced/(l*day) were achieved, with a conversion efficiency of up to 98%. Using mixed populations of acidophilic fungi and iron-reducing bacteria, the bioreactors were capable of promoting iron reduction using paper pulp as sole carbon and energy source. Reduction of sulfate in pack bed bioreactors was observed with acidic wastewaters of pH 3 and above, though average rates of 300 mg sulfate reduced/(l*/day) were less than those recorded for circum-neutral pH systems. Bioremediation of ferric iron-rich ARD was assessed using coupled iron-reducing and sulfate reducing bioreactors.

Jan 1, 2000

By Yixian Zhao

Although many ultimate pit limit design algorithms have been developed for the past one- quarter century, only the well known Lerchs-Grossmann's (LG) algorithm is capable of producing a truly optimum ultimate pit limit today. This paper presents a graph theory oriented algorithm for optimum ultimate pit limit design. This algorithm produces a true optimal solution and maximizes the total undiscounted net profit for a given 3-D block mine model. The algorithm performs much better than the well known LG algorithm, in terms of the reduction in computation time and computer memory requirements. More importantly the new algorithm is easier to understand and implement than the LG algorithm. Specifically, this paper discusses: 1) the computer representation of arcs and the rules of arc generations which dictate the formation of trees in the graph, 2) the mechanism of joint support and re-allocation, 3) the properties, the general procedures of the algorithm, and the suggested specific steps to implement the algorithm, 4) comparison between the new algorithm with LG algorithm, and 5) some experience in implementation of the algorithm and two case study results.

Jan 1, 1992

By J. Roth

PROLOGUE Nowadays, where production costs and energy costs are increasing and at the same time requirements in fineness and purity of industrial mineral products are getting higher and higher, industry has to look for more efficient grinding systems and developments to produce these products more economically. Therefore lots of new developments in high energy jet mill pulverizing have been made. In the main, however, these developments involved more or less just the new principle of fluidized bed jet pulverizers but not the older spiral jet mill principle. In some cases, especially in the filler industry where laminar minerals are used and higher aspect ratios are required, the spiral jet mill principle has advantages in a better delamination of these minerals. To comminute minerals down to products with a d97 < 3 µm, the specific energy consumption increases up to 2,000 kWh/t – 3,000 kWh/t or even more, depending on the grindability of the mineral. So the production of these fine materials is quite an expensive task. But jet mill grinding is and will be the most favorable method to produce micro-products and in the near future nano-products, despite the high energy consumption.

Jan 1, 2000

By J. Fisher, M. Barish

Over the past several years, Somerset International has successfully installed over 20 patented Sub325® Fine Coal Recovery Systems in the United States, Australia, Canada and Russia. These installations recover between 5 TPH and 40 TPH for the host sites. In addition to the increased revenue from the direct recovery of a recirculating load (Screen Bowl “Insurance”, Direct Recovery vs. Indirect Recovery via Recycle, CPSA 2020), host sites have seen benefits ranging from improved operation of refuse equipment to a reduction in the solids content of the refuse streams. As Somerset has improved ultra-fine coal recovery through the introduction of Sub325® Effluent Flotation and, most recently, the Sub325® Effluent Settler™, the amount of coal that has been recovered from these systems has increased by up to as much as 25%. Many host sites have taken a sense of ownership in the Somerset system and consider it to be a critical circuit in the overall optimal performance of the plant. In the past year, Somerset has taken the initiative to expand upon the capabilities of the Sub325® Fine Coal Recovery System, primarily the Sub325® Solid Bowl Centrifuge, to include Refuse Tailings Dewatering to allow for co-mingled refuse disposal. As slurry ponds and boreholes are becoming difficult to impossible to permit and operate, there is a need for a reliable, low-maintenance, continuous operation that can produce a handleable refuse cake. Refuse tailings disposal applications are by no means limited to coal plants and impoundments. Somerset has successfully tested at iron ore and phosphate locations throughout the world and have begun commercial installations. The ability to dewater -325 mesh material, whether it be coal, coal refuse, iron ore tailings, or something else, is a vital piece of processing capability for the continued production of mining operations across the globe. This paper highlights the success that Somerset has had in the coal industry worldwide as well as the initial successes with phosphate, iron ore, and copper tailings (patent pending).

Mar 2, 2022

By G. L. Mowrey

A new coal interface detection (CID) method is under investigation by the U.S. Bureau of Mines. This novel concept is based on utilizing a passive infrared system (FIR) to measure temperature changes associated with the cutting of coal and adjacent strata. For this method to work successfully, a definite mechanical/hardness contrast must exist between coal and rock. Advantages include that FIR responds instantaneously at the coal-rock interface and it is minimally affected by dust and/or water sprays. Based on preliminary tests, results indicate that the PIR method can be applied successfully in mines having a hard immediate roof.

Jan 1, 1990

By I. B. Tulu, M. M. Sears

In 2015, 40 longwall mines provided nearly 60% of the US coal production from underground mining methods. This represents a substantial yet gradual increase from just under 50% over the last 5 years. As a result of this increased production share, the percentage of ground-fall-related fatalities in longwall mines has also increased when compared to all US underground coal mines. Additionally, about 80% of ground-fall-related fatalities have occurred in areas where the roof was supported. In an attempt to better understand the status quo of current US longwall support practices, a sample of 25 longwall mines were visited representing nearly 50% of the currently active longwall mines representing all of the major US longwall-producing regions. The resulting data was obtained from a wide variety of overburden depths, geologic conditions, mining heights, ground conditions, support practices, and gateroad configurations. The data collected is reported using both qualitative and quantitative methods. Results from the research update previous efforts in classifying mining accidents and injuries as well as current support practices presented by this author at the 2017 Society for Mining, Metallurgy, & Exploration Annual Meeting. This data provides a necessary background for future research aimed at further reduction of ground fall accidents and injuries.

By Wang Yingmin, Xu Zhuyun

There are 3 steps in the process of forming a mine ventilation system, (1) selecting a reasonable ventilation pattern (included pit shaft arrangement); (2) optimizing of the ventilation network and (3) computing and outputting the flow splitting results of the network with the optimal ventilating equipments selected. In the past, the first step was relied on artificial decision-making. In order to design a common ventilation system, some ventilation experts were needed to participate or do some examinations. Even so, the design made was reasonable only for those experts. If there is a mistake in the first step, then even the followed 2 steps are best done, the losses are very difficult to retrieve. So that, the first step is very important. The development of expert systems provided an efficient means and tool for all engineering fields. This paper presents an expert system of selecting mine ventilation pattern and pit shaft arrangement. After testing many times, it is shown that the system can perform the first step of designing a mine ventilation system, and can help the experts doing their study works more efficiently.

Jan 1, 1991

By J. M. Schisler

In the last five years Eldorado Resources Ltd. (ERL) has undergone a major expansion and modernization of its uranium refining and conversion plants. A new refinery for processing yellow cake to UO3 was constructed at Blind River in northern Ontario and started up in 1985. Its rated capacity is 18,000 t/a uranium as UO3. At Port Hope, Ontario, ERL&apos;s new UF6 conversion plant has been constructed. This plant started up in 1984. It utilizes the novel, wet-way process to produce UF4 and gives the company a UF6 production capacity of 14,500 t/a U. Also at Port Hope is Eldorado&apos;s ceramic UO2 powder production facility, commissioned in late 1980. It has a capacity of 1700 t/a uranium as UO8. With the completion of these capital projects, Eldorado has the largest and most up-to-date refining and conversion facilities in the western world. This paper reviews the refining process and process design. The methodology used to start up the Blind River plant is described as are some startup difficulties, solutions that were developed, and the resultant current operation.

Jan 1, 1987