Search Documents

By M. J. Friedel

The U.S. Bureau of Mines (USBM) investigated the use of seismic refraction tomography (SRT) for identifying changes in pillar loading at the Foidel Creek coal mine near Steamboat Springs, CO. The inherent three-dimensional problem of directly imaging coal pillar conditions is reduced to a single plane by considering only the load transmitted from the pillar to the adjacent floor rock. Floor strata velocity tomograms (at two pillar locations) illustrate that loading conditions are non-uniform and non-unique. Also, time sequence monitoring, as the longwall face advanced, demonstrated that SRT can be used to image spatial changes in loading conditions. SRT offers the mining engineer a simple and flexible technique for evaluating pillar conditions, and thus, both present and alternative mine designs.

Jan 1, 1994

By R. A. Pimentel

Complying with reduced dust standards (i.e., less than 2.0 mg/m3) due to quartz levels that exceed 5 percent is presently a critical problem for many continuous mining sections. Results are presented of research which was performed to determine the factors causing high levels of respirable quartz dust and to identify the major contributors to operator exposure. It was found that the significant sources of quartz dust are the drilling of the roof and the mining of the roof, floor and rock bands. Both the miner and the bolter may be on a reduced standard, but compliance is easiest to achieve on the bolter for which improvements in maintenance and operator practices are usually sufficient. At the miner, the problem is more elusive. Research continues to identify operating and mining practices that contribute to the exposure..

Jan 1, 1985

By R. Stanevich

Studies by the National Institute for Occupational Safety and Health (NIOSH) and the Bureau of Mines (BOM) have demonstrated that: (1) 90% of diesel particulate is less than one (1) micrometer in aerodynamic diameter; (2) more than 90% of the respirable mass in electric coal mines was greater than one (1) micrometer in aerodynamic diameter; and (3) in coal mines using diesel equipment, average diesel concentrations can represent up to 53% of the MRE respirable coal dust standard. For mines approaching the 2 mg/m3 standard, compliance may be easier to attain by controls directed at diesel exhaust particulate as opposed to coal dust control. First, however, a Simple instrument is needed to measure diesel exhaust particulate concentrations. This paper describes such a sampler, its construction, and use. While results from this sampler are primarily utilized to identify control areas, NIOSH is also using the sampler for estimating worker exposures in epidemiologic studies.

Jan 1, 1988

By James G. Mock

The choice of equipment to be applied to a given installation by the Application Engineer begins with the data as presented to him by the user. This point in the relationship establishes a communication link, which will decide whether or not the correct piece of Overhead Equipment is applied at the most economic advantage to the user. The role played by the user cannot be minimized. No one knows better than he, just what work he expects to accomplish with this piece of machinery. However, all too often, he oversimplifies the requirements, and along with minimal crane and building parameters, merely refers to one of the following crane classifications as defined by The Crane Manufacturing Association of America, as shown in Figures 1, 2, 3, 4, 5, 6 and 7. This approach places the ultimate user in an unfair position, since he has then assumed the status of the machinery designer and must, therefore, assume the responsibility of the success or failure of the operation of that piece of machinery. If the user selects a Class "C" crane for his job requirement, when actually a Class "B" crane can adequately handle the work load, he is not offering the most economic solution to his company and added little to the cranes service capabilities.

Jan 1, 1973

By T. W. Beck, J. A. Organiscak

The U.S. National Institute for Occupational Safety and Health (NIOSH) Office of Mine Safety and Health Research (OMSHR) has recently studied several redirected scrubber discharge configurations in its full-scale continuous miner gallery for both dust and gas control when using an exhaust face ventilation system. Dust and gas measurements around the continuous mining machine in the laboratory showed that the conventional scrubber discharge directed outby the face with a 12.2-m (40-ft) exhaust curtain setback appeared to be one of the better configurations for controlling dust and gas. Redirecting all the air toward the face equally up both sides of the machine increased the dust and gas concentrations around the machine. When all of the air was redirected toward the face on the off-curtain side of the machine, gas accumulations tended to be reduced at the face, at the expense of increased dust levels in the return and on the curtain side of the mining machine. A 6.1-m (20-ft) exhaust curtain setback without the scrubber operating resulted in the lowest dust levels around the continuous mining machine, but this configuration resulted in some of the highest levels of dust in the return and gas on the off-curtain side of the mining face. Two field studies showed some similarities to the laboratory findings, with elevated dust levels at the rear corners of the continuous miner when all of the scrubber exhaust was redirected toward the face either up the off-tubing side or equally up both sides of the mining machine.

Jan 1, 2013

By Madan M. Singh

With the current emphasis on ecology, safety, and conservation of natural resources, some consideration should be given to methods of mining that reduce surface damage, make the mining of coal less hazardous, and allow exploitation of a larger percentage of the coal in situ. One method that can be helpful toward attaining these objectives is the use of packing or stowing. Stowing involves the replacement of the ore that has been removed by waste material obtained from within the mine or elsewhere. Evidently, it would be most beneficial if this waste for packing were available from the mine being worked, but generally this is not possible. If complete stowing is adopted, it is necessary to bring in packing material from other sources. Stowing tends to reduce surface subsidence, but not eliminate it. It enhances roof support and curtails accumulation of methane in the gob, making the mining operations safer. It may also allow one to obtain a larger amount of coal. Currently, in the United States, a substantial amount of coal is left in place as pillars, in the hope that it will support the overburden indefinitely. Some of these could be extracted with stowing. The mining of thick, steep, or contiguous seams would also be facilitated.

Jan 1, 1974

By D. H. Carlson, J. H. Johnson, C. F. Renders

Research was conducted at a western coal mine on a wide variety of underground mining vehicles to develop testing procedures for portable instrumentation monitoring of tailpipe concentrations of diesel particulate matter (DPM), carbon dioxide (CO2) carbon monoxide (CO) and nitric oxide (NO). DPM was measured using the Emissions Measurement Appa¬ratus (EMA) developed by Michigan Technological University (MTU), and an ECOM-KL five-gas analyzer was used to measure gaseous tailpipe concentrations. Baseline concentrations of the tailpipe pollutants were measured using vehicle systems to load the engine. Concentrations before and after the water scrubber were measured and water scrubber efficiencies were estimated by calculation. Field measurement procedures were established. Heavy-duty vehicles with automatic transmissions were loaded using the torque converter to stall the engine. Consistent engine loading for light-duty vehicles with manual transmissions involved placing the transmission in neutral and adjusting the throttle to maintain a constant engine speed of 2,500 rpm. Tailpipe CO2 concentrations for Caterpillar 3306 and 3304 engines were compared to laboratory CO2 data from Caterpillar and MSHA to help determine if engine settings were correctly adjusted for operation at high altitudes. (Perfect agreement between the mine vehicle tailpipe and laboratory measurements would not be expected because of the differences in the test conditions.) DPM concentrations for light-duty vehicles ranged from about 20 to 160 mg/m3, and one light-duty vehicle averaged near 1,000 mg/m3. DPM concentrations for heavy-duty vehicles ranged from about 55 to 200 mg/m3. Widely ranging DPM concentrations for a particular vehicle type reflect the state of maintenance, fuel rate settings and different engine loading procedures as well as differences between samples collected upstream and downstream of the waterscrubber. The calculated DPM removal efficiencies due to the water scrubber varied considerably between vehicles, ranging from 13% to 51%. Calculations indicate that, under worst-case conditions, very large reductions in DPM may be required to meet the proposed DPM PEL of 0.15 mg/m3, even on vehicles with water scrubbers. In-mine ambient air studies, which are needed to actually measure the impact of the tailpipe concentrations on the work environment and the effect of mine ventilation on the dilution of DPM were not done in this first set of tests.

Jan 1, 2000

By J. L. Carr, A. K. Smith, C. C. Jobes, G. T. Homce

"Underground continuous mining machines pose a difficult safety challenge since their operators generally work in close proximity to these machines in very restricted spaces. Intelligent software for use with magnetic proximity detection systems has been shown to accurately locate workers around mining machinery in real time. Calibrating these systems requires the manipulation of a lot of data to determine the calibration constants. Researchers have developed software to analyze, convert, and visualize data acquired during this calibration process to more accurately model magnetic fields and their interaction with the environment. This paper details the background, development, and operation of the resulting application software focusing on the utility of the graphical user interface to visualize the magnetic field calibration data. The refined data developed by this process can then be utilized by the proximity detection system to more accurately identify the location of miners working in an underground mining environment. INTRODUCTION Roughly half of the electricity consumed in the United States is produced with coal, and roughly one-third of all US coal production comes from underground mines [1]. Over the last century underground mining health and safety has seen a continuous and dramatic improvement. However, machine-related injuries and fatalities continue to be a major safety concern [2]. Every year, hundreds of miners are severely injured while operating underground mining equipment, and 39 miners have been killed in striking/pinning accidents involving continuous mining machines (CMMs) since 1984. CMMs, such as the one shown in Figure 1, are large mobile machines that are used to mechanically cut coal in an underground mine. These machines weigh approximately 40 to 50 tons, have hydraulically articulated appendages, and are capable of moving at speeds up to six feet per second [3]. Modern CMMs are remote-controlled, yet the operator and other miners are often in close proximity to the machine. Recent research by the National Institute for Occupational Safety and Health (NIOSH) reveals that the locations workers take relative to the CMM are usually influenced by visibility requirements and safety concerns [4]. The Mine Safety and Health Administration (MSHA) estimates that at least 28 fatalities involving CMMs since October of 1984 may have been prevented with proximity detection technology [5]. MSHA further estimates that proximity detection could prevent 20% of all deaths throughout the industry [6]."

Jan 1, 2016

By P. T. Luckie

Analysis of classifier performance independently of a closed grinding circuit configuration may result in a poor match-up between the grinding device and the classifying device. This paper examines the relationship between classifier and grinding device in dry grinding circuits by employing a semi-empirical methodology.

Jan 1, 1980

By R. A. Matuszak

Historically most mine management teams have been forced to operate in a more or less subjective manner. The objectives of mine management are simple and clear. Like other operational managements, mine management teams have the traditional well defined goals of improving efficiency and production while decreasing costs. Unlike other operational managements however, mining teams deal regularly with a vast assortment of uncertainties caused by: - Key production tools being mobile and widely dispersed, and - Non-uniform mining conditions At best in most operations these conditions cause obstacles to productivity and at the same time cause long delay in managment awareness of the obstacles. Planning with delayed feedback of information about necessary deviations is incomplete planning. For these reasons increased operational efficiency remains a constant though somewhat elusive goal.

Jan 1, 1985

By Robert D. Schmidt

The Cyprus Casa Grande Corporation has provided Bureau of Mines researchers with an opportunity to investigate the hydrology of leaching an in place copper ore deposit. Hydrologic investigations of underground in situ copper leaching are being jointly conducted under a cooperative agreement. The hydrologic concerns of leaching operations at the Casa Grande mine focus on maintaining adequate solution injection and recovery rates, and on distributing the injected leach solution effectively within the ore deposit. Hydrologic considerations underlying these concerns relate to the permeability of the oxide ore zone during leaching, the unsaturated condition of the deposit prior to leaching, and the constraints imposed on in situ hydrologic design by the underground mine setting. The investigation involves monitoring of flow and pressure conditions in 58 injection and recovery wells, estimating permeability conditions using a hydrologic model, and on-site testing of hydrodilation and airlift pumping. Transient, fracture-controlled permeability is determined to be the dominant hydrologic consideration. A statistical modeling procedure has been developed for estimating changes in permeability during leaching. Flexibility in well design and operation is essential for accommodating the changes in fracture permeability that occur during leaching.

Jan 1, 1990

When the Middle Ages were drawing to an end and Rotterdam, then still a small fishing port, began to extend its trade relations to continental ports handling general cargo, a development was initiated which was to give Rotterdam a predominant position in maritime traffic in Europe 300 years later. Despite many setbacks and the silting up of the mouths of the Rhine and Meuse rivers, the port experienced a new rise towards the end of the previous century after the dunes at Hook of Holland had been cut through as planned by Dutch engineer Caland. With its favourable location in the mouth area of the Rhine and a hinterland opened up by waterways it was merely a matter of the city council pursuing a far-sighted policy to make the best of these natural advantages. Thus new port installations were erected on the southern bank of the Meuse in the first quarter of this century, which were expanded in the course of the subsequent decades. The New Waterway became the main artery for industrial enterprises, in particular oil industries, which sprang up along its banks (picture 1). Whereas 30 years ago Rotterdam's Waalhaven, with its new jettees for general cargo and mainly bulk goods, was still one of the most modern terminals, the growing size of ships, which increased by leaps and bounds for tankers, in particular towards the end of the 'fifties, necessitated much larger harbour facilities built further and further towards deep water.

Jan 1, 1972

In 1991, US mine production of barite decreased 3.4%. Barite consumption, sold or used by grinding plants, decreased by 11.7%. Imports also decreased by 15.4% over 1990. World mine production increased I%, according to the US Bureau of Mines. The value of domestically produced barite, f.o.b. mine, increased 3.3% according to the Bureau. The declared value c.i.f. US port of all imported crude barite during 1991 increased from $40.61/t ($36.84/st) in 1990 to $42.35/t ($38.42/st), the Bureau stated. Nevada was the leading producer of barite with 78% of the total, followed by Georgia and Missouri. It is estimated that 75% of the domestically mined barite was used as a weighting agent in drilling fluids. The remaining 25% was used in barium chemicals, glass or as a filler. Most of the production from Missouri, Georgia and Tennessee was used in the non-oilfield sector. Of the total barite used by grinding plants and chemical manufacturers, it is estimated that 93% was used in drilling fluids. The remaining 7% was in the non-oilfield sector, including barium chemicals and fillers in paper, plastics and glass. Tonnage consumed in the drilling fluids market decreased due to the lower average rig count during 1990. The average number of rotary rigs operating was 860. That was 14.9% less than the 1990 average of 1010 in the US. Crude barite imports were 138 kt (152,000 st) less than 1990 or 15.4%. Imports accounted for 70% of the (ap¬parent) barite consumed in the US. During 1991, China continued to be the leading exporter of crude barite ore to the US with 85.1 %. India followed with 14.8%. About 97.5% of the imported barite ore was used in the oilfield sector. Ground barite imports decreased from 56.7 to 46.2 kt (62,500 to 51,000 st) 1991. Mexico was a major exporter to the US, accounting for 75.3% of the total ground barite imports. Canada shipped 23.7%, while other countries accounted for less than 1 %, primarily for the nonoilfield market. During 1991, the number of grinding plants supplying the drilling fluids market along the Gulf Coast was reduced from 12 to 10. Baroid Drilling Fluids completed its mining program at the Rossi Mine near Dunphy, NV.

Jan 1, 1992

By J. E. Jennings

The problems of slope stability in open-cast mines are examined. A criterion, the instantaneous stripping ratio, is suggested for use in the design of pit slopes and as an index of control at all stages of the exploitation of the ore body, This criterion may also be related to safety and to the maximizing of profits. Two approaches to safe design of slopes, one from the point of view of soil mechanics and the other from the point of view of rock mechanics, are described and critically compared. The effect on slope stability of the regional tectonic stress field is discussed. Explanation is given of the application of the Terzaghi effective stress concept to problems in both soil and rock environments, including possible effects when borehole deformation techniques are used to measure stresses in rock in situ.

Jan 1, 1963

By B. M. Kunar, C. S. N. Murthy, B. Rao K

Rock particle size has a very important significance in the mining industry, starting from blasting till the mineral processing. The present study was carried out to understand the particle size distribution in various sieves after conducting the ball milling process. The time of the grinding process was varied at different intervals. It was observed that 80% of the particles of both granite and marble rock samples passed through the 4800 μm sieve when subjected to grinding time of 40 minutes. Also, it was observed the number of particles that were retained in the smallest sieve of <75 μm was higher in the case of granite sample when compared to a marble sample. INTRODUCTION India is a major exporter of granite and marble stones. The major use of marbles and granites are constructing walls and floors. There are several machining processes that are applied before it is used as floors and walls. During this process, wastes are produced these wastes are used in various ways. These include use of powders for clay products (Segadães, Carvalho, & Acchar, 2005), as an additive in cement production (Aruntaş, Gürü, Dayi, & Tekin, 2010), to enhance the properties of brick ceramics (Saboya, Xavier, & Alexandre, 2007), in constructing bricks (Bilgin et al., 2012) and as an additive in concretes (Aliabdo, Abd Elmoaty, & Auda, 2014). Usually, the powder form of marble and granites are used as an additive in the above-mentioned applications. Powders of marble and granite are obtained through the grinding process. One such process of grinding is the ball milling process. In the ball milling process, a quantity of samples along with the charge quantity consisting of steel ball is subjected to a grinding process within a closed chamber as shown in Fig. 1. An even particle size can be obtained through sieving the material after subjecting it to grinding. The present study is planned to understand the particle size distribution in various sieves due to varying time and charge quantity in the experiment. Only time was varied to understand the amount of particle distribution in the case of granite and marble rock samples and a comparison is drawn. A statistical model was developed for marble rock specimen considering the data obtained by varying time and charge quantity in the ball mill experiment.

Jan 1, 2019

By D. J. Gurtler

On January I, 1988, Chino Mines Company initiated the use of a system of economic splits for all materials encountered in mining. All mined material is evaluated as mill ore, solvent extraction-electrowinning plant feed and non-ore material to determine its disposition. Post-implementation studies indicate that a significant increase in financial returns on material mined was realized when compared with the copper cut-off grade previously in use.

Jan 1, 1990

By James M. Griffin

Ladies and Gentlemen, There have been no less than ten major coal project financings in the last eighteen months. Each of these has been in the order of $100 million to $1 billion for the development of a coal property and its associated infrastructure. It is appropriate at this time to review the nature of these past financings. Why has there been so much activity? There are primarily two reasons. The first is due to the large number of contracts which were signed as a result of OPEC oil shocks. High projections were made for increased coal consumption particularly in world trade. This is distinct from domestic coal mine/power plant projects which often tap a government source of funds. Second is the high cost of coal development in the 1980&apos;s compared with a typical company&apos;s corporate borrowing capacity.

Jan 1, 1984

By J. A. Chermak

Piles of sulfide-bearing overburden, ore, and tailings have the potential to generate acid drainage (AD) when exposed to an oxidizing environment. Laboratory column experiments were conducted using acid-generating overburden material with an added surface amendment of limestone and/or lime. Artificial rainwater was introduced and allowed to drain through the columns. Results showed that the limestone and/or lime reacted with the acidic rock, resulting in the precipitation of a hardpan layer of gypsum and amorphous iron oxy-hydroxide at the surface. The hardpan layer significantly reduced the effective permeability of the column. Based on this study, hardpan layers can be created as chemical caps to significantly reduce the infiltration of rainwater and snowmelt into acidic overburden or tailings material. Unlike traditional capping methods (for example, clay and high density polyethylene (HDPE) covers), chemical caps are self-healing.

Jan 1, 1996

By G. Castillo, J. Mortensen

"INTRODUCTION Molybdenite is typically produced as a co-product in the copper ore flotation process. At the Rio Tinto Kennecott Concentrator (RTKC) in Copperton, Utah, the molybdenite is initially floated with copper sulfides and other value minerals producing a Cu-Mo concentrate. This is then separated in the molybdenum plant by depressing copper sulfides and pyrite and floating only molybdenite. The molybdenum plant in RTKC comprises the rougher circuit and several stages of cleaning to achieve a certain grade requirement of Mo. The rougher circuit is where the first stage of separation occurs. Cu sulfides and pyrite are depressed in the rougher circuit by adding NaSH under nitrogen and in the cleaner circuit by adding NaSH under air. The depression of Cu sulfides (and pyrite) by NaSH is related to the redox activity1. It is important therefore to maintain a reducing potential in the circuit in order to achieve effective Cu-Mo separation. If the rougher circuit is under air, like RTKC’s molybdenum cleaner circuits, it is harder to maintain the target redox potential because NaSH oxidizes rapidly in the presence of air thereby increasing NaSH consumption significantly. CU-MO SEPARATION AND ROLE OF PULP POTENTIAL The collector adsorption on copper sulfide minerals is through an electrochemical mechanism2. The collector changes the surface chemistry of the Cu mineral allowing it to float. Molybdenite, or MoS2, on the other hand, floats readily in the presence of a frother as it is naturally hydrophobic. Usually, hydrocarbon oil extenders such as diesel or burner oil are added to enhance Mo recovery. In order to effectively separate Cu from Mo, the collector complex on the copper surface needs to be destabilized or desorbed using a reducing agent such as NaSH or Nokes. As long as the circuit is under highly reducing conditions, the collector remains detached from the sulfide mineral surface allowing Cu sulfide depression. Therefore, it is important to measure the oxidation-reduction potential (ORP) continually and maintain the reducing condition with addition of NaSH. For a given collector each mineral will have a characteristic potential or electrochemical window for flotation to occur3, therefore, it is necessary to reduce the potential outside of this window in order to effectively separate Cu and Fe sulfides from MoS2 minerals2. In RTKC plant, the target reducing condition is between -450 to -550 mV to effectively destabilize the collector and depress Cu and Fe minerals. Typically the dosage of NaSH used in the molybdenum plant could range from 6 to 30 gallons/min (gpm). The high dosage of NaSH could pose risk of H2S exposure. RTKC wanted to evaluate alternatives to NaSH in order to reduce its consumption and minimize risk of H2S gas generation."

Jan 1, 2016

By Elwyn H. King, Thomas R. Kuesel

I. CONCEPT MARTA&apos;s Peachtree Center Station is being mined out of hard rock, directly beneath Atlanta&apos;s central business district, with minimal surface disruption during construction. Its cost is competitive with that of a conventional cut-and-cover alternative owing to its design concept, which utilizes the rock as a primary structural and architectural material. II. PLANNING The station was originally planned for cut-and-cover construction. However, Peachtree Street is unusually narrow for a main business street (generally 78 feet (24 m) between building lines) and cut-and-cover construction would therefore be very disruptive to surface traffic and severely restrict access to adjacent buildings, including Peachtree Center, Atlanta&apos;s showcase business/commercial complex. (See Fig. 1.) Tunneling had been considered, but was initially thought [ ]

Jan 1, 1979