Search Documents

By R. A. Pimentel

Many longwall operators experience difficulty complying with the federal regulation limiting average dust exposure. Others are currently in compliance, but the dust exposure limit keeps then from increasing their production. Spray water is a major means of dust control. Excess water can cause problems in the transportation system and the cleaning plant, and reduces the Btu value of the run of mine coal. Thus, the dust exposure reduction per unit of water sprayed must be maximized. This paper discusses underground tests recently completed as part of a Bureau of Mines research program to determine the effects of variations in spray water flow rate, pressure, proportioning and spray orientation on longwall shearers.

Jan 1, 1984

By Louis M. Schlesinger

KMG Minerals, Inc., a mica-feldspar-quartz producer in Kings Mountain, N.C., uses about 50% of its plant's -200 mesh slimes to manufacture brick. However, the company is unable to market the remaining 50% of this fine mineral mixture. The NCSU Minerals Research Laboratory operated a pilot plant to process these slimes to produce an additional product. The process, consisting of blunging and hydraulic sizing, was designed to separate a kaolin-enriched -270 mesh product from the bulk of the coarser +270 mesh "grit" minerals. Size analysis showed that this product was 80% finer than 20 microns and 50% finer than 6 microns (in equivalent spherical diameter). An evaluation indicated that it is a hydrous aluminum silicate that might be suitable in the filler and extender markets for traffic paint, some types of plastics, joint cements, and dusting compounds. Because of its high viscosity, it will be difficult to use more than a small percentage in cast ceramic bodies. However, it might be possible to use up to 10% in extruded ceramic bodies (i.e., electrical porcelain). The 15.2 cm (6 in,) diameter Linatex Hydrosizer was tested using a range of teeter water flowrates, so that the net rise velocity was varied from 0.10 cm/s to 0.40 cm/s. The solid feed rate to the sizer was maintained at approximately 1.1 t/hr/m2 (0.12 ton/hr/ft2). Tests were run using both "shallow" (i.e., 6 in.) and "deep" (i.e., 15 in. teetered beds. The best overall result was obtained when the sizer was operated with the "deep" teeter bed and a net rise velocity of 0.10 cm/s. About 97% of the +270 mesh material was rejected and approximately 79% of the -270 mesh material was recovered in a 14% solids slurry.

Jan 1, 1994

By Ulrich Maidl, Marc Comulada, Janosch Stascheit

"INTRODUCTION Cohesive soils are notorious for causing clogging of the cutter head and the excavation chamber of tunnel boring machines (TBMs). While clogging leads to a drastic reduction in excavation performance, it further induces higher wear of tools and other parts of the cutter head and may even prevent a controlled support of the tunnel face and, thus, lead to face collapse and excess settlements or sinkholes. Employing well-balanced soil conditioning techniques, the clogging tendency can be significantly reduced. The monitoring and control of soil conditioning as well as the timely detection of potential clogging tendencies require a close monitoring of all relevant machine parameters and measurements. To this end, a reliable and powerful Process Controlling software that gathers all machine and process-related information is a prerequisite for successful mitigation of clogging-induced problems. The remainder of this contribution is organized as follows: First, a brief introduction to the Process Controlling system PROCON is given. Afterwards, the mechanisms and mitigation techniques of clogging are discussed. Finally, an example is given how Process Controlling has been employed to soil conditioning in a tunneling project with highly clogging soils.PROCESS CONTROLLING Being both the active part and a huge measuring device, the shield machine represents the core component in mechanized tunneling. This machine comprises a manifold of complex components and devices that require constant supervision and control and, thus, is equipped with a manifold of different sensors that provide a continuous monitoring of the state and condition of the machine (Maidl & Stascheit, 2014). If these data are put into the whole context of the tunneling process, they can provide insight to the assessment and optimization of the performance and to the prediction of potential risks and hazards such as, for example, the tendency of clogging of the cutter head."

Jan 1, 2016

By J. Kou

In this paper the activation behavior of quartz using Ca(OH)2 as an activator in quartz reverse flotation with anionic collector was evaluated and their adsorption behavior was investigated using a variety of techniques. The adsorption of the collector KS-I on the surface of quartz with and without Ca2+ was primarily characterized using Quartz Crystal Microbalance with Dissipation technique (QCM-D), which is a high sensitivity in-situ surface characterization technique. The flotation performance was evaluated using a laboratory mechanical flotation cell at different process parameters such as pH, collector dosage, and Ca(OH)2 dosage. The anionic collector evaluated was a commercial fatty acid KS-I. The QCM-D data showed that the collector adsorbed on quartz more readily with Ca2+ as activator. The mass and structural property of the collector layer adsorbed on quartz surface at 2.16×10-3 mol/L of Ca2+, 0.3 g/L of collector and pH 12.0 have been studied using the technique of QCM-D. The chemisorption of the collector KS-I on the surface of quartz in presence of Ca2+ were also demonstrated by means of zeta potential, QCM-D and FTIR analysis.

Feb 23, 2014

By H. Walqui

The Empire concentrator currently processes magnetite ore from the Empire pit which is approaching the end of its mine life. Over the past two years plant wide tests have been run to access the plant capability of processing ore from the neighboring sister Magnetite pit. The neighboring pit presents challenges to the Empire plant due to its higher feed grade, finer liberation size and higher percent silica which require additional secondary grinding and concentrating capacity to achieve concentrate grade. The following paper summarizes the results from the second full scale test, run during 2009 under a challenging market environment

Jan 1, 2010

By Corale L. Brierley

Bacteria, algae and fungi react to heavy metals in their environment by immobilizing, mobilizing and/or transforming metals. Microorganisms carry out these changes by (1) precipitating metals outside of the microbial cell, (2) binding and complexing metals to the outside of the microbial cell's protective coating, (3) accumulating metals inside of the microbial cell, or (4) transforming metals by oxidation, reduction, methylation or demethylation. Most of these mechanisms are operative in constructed aerobic and anaerobic wetlands for metal's remediation. Several more advanced biotechnologies for metal's removal from aqueous streams have been introduced, but have not been widely accepted commercially.

Jan 1, 1995

By J. L. Fuller

Thousands of mine air samples are taken underground each year by MSHA inspection personnel in order to further assure that miners have a safe and healthy environment in which to work. While most air samples are taken with stain tubes, many samples are obtained in evacuated containers and returned to a laboratory for more accurate analysis on a gas chromatograph. In order to enhance the accuracy, reliability and repeatability of the samples taken with evacuated containers, improved procedures have been developed, which are described in this report, for filling two different types of evacuated sample containers using either mechanical or electrical pumps. In those instances, such as when sampling strata gases in drill holes, where mathematical calculations may be required for proper sampling, example calculations are provided. The use of a third type of evacuated container, which is generally restricted to non-specific sampling of the ambient mine atmosphere, is also described.

Jan 1, 1986

By Paul Eimon

The 1981 Fall field trip of the Denver Region Exploration Geologists' Society focuses on Creede. That is appropriate - because significant mining history has been made and is being made in this off-the-beaten track, high-country mining district. Creede is one of the few Colorado bonanza towns which was big in the 19th Century, had its ups and downs, and produced almost continuously since its discovery. Creede is important to geologists for its: precious and base metal production, current exploration activity, and research into near-surface hydrothermal systems. United States Geological Survey research and field geologists zeroed in on Creede some 25 years ago and their steady, consistent work is now being spotlighted and appreciated.

Jan 1, 1981

By M. A. Anderson

After mope than fifty years Of Continuous operation, the Nevada Mines Division found itself faced with declining ore headings and metallurgical efficiencies, and rising operating costs. Although intensive process improvement programs had been initiated at various times in its history, insufficient return on investment served to defeat plans for any major changes in circuitry. The advent of practical large-volume flotation machinery, along with the success of long-range exploration drilling programs, complimented the results of an intensive program of research and development. The result of laboratory testing, pilot plant testing, and full scale plant tests was the proven indication of metallurgical improvement given increased flotation residence time and the effect of mechanical agitation in flotation.

Jan 1, 1975

By K. F. Unrug

Martin County Coal Corporation is located in Martin County, Kentucky in the Appalachian coal fields, near the West Virginia border. The total leasehold covers more than 33 000 acres. Total annual production at Martin County Coal Corporation is currently 2,500,000 tons, but in certain years exceeded 3,000,000 tons. Approximately 45 percent of the annual production comes from two surface mines. The balance is produced from five underground mines. Martin County Coal Corporation's work schedule consists of 240 days/year, two nine-hours shifts/day.

Jan 1, 1991

By J. D. Miller

Physical separation of bitumen from low-grade Utah tar sand deposits containing a relatively high viscosity bitumen phase (Sunnyside and Tar Sand Triangle deposits) has been accomplished by traditional size reduction and froth flotation techniques. At appropriate experimental conditions more than 90 percent of the bitumen can be recovered in a concentrate, containing more than 20 weight percent bitumen, which should be a suitable feed material for subsequent hot water or thermal processing. The efficiency of bitumen recovery depends on the extent of size reduction, promoter and dispersant addition. Rejection of greater than 60 percent of the sand at ambient temperature and ease of water removal from the concentrate make such a process strategy both energy and cost effective. The energy required to achieve effective separation by the ambient temperature process is significantly less than the energy required for the recently developed hot water process. The flotation behavior of the tar sand has been analysed with respect to flotation pH, contact angle measurements and the apparent iso- electric point of the bitumen. The best flotation response at pH 7.8 to 9.0 can be correlated with the maximum in contact angle developed between the air bubble and bitumen surface and with the apparent iso-electric point of the bitumen (-pH 8.0).

Jan 1, 1981

By Frederick P. Agterberg

It can be useful to model the mean grade values for a metal in mineral deposits containing that metal as representing the extreme value tail of a lognormal frequency distribution for the concentration values of the metal in rocks of all types. Results for copper and zinc in the Abitibi area of the Canadian Shield are compared to results previously obtained for the Canadian Appalachian Region. The lognormal model is also applied to a set of 162 large gold deposits in the Abitibi area. In the second part of the paper, 1311 large and small gold deposits in the Abitibi area are modelled as discrete events. By means of a newly developed spatial clustering model it is possible to predict the variances of random variables for frequencies of deposits in cells of different sizes.

Jan 1, 1979

By L. Yuan, J. H. Rowland, D. Bahrami, R. Thomas

Blasting is the main method of production in many non-coal underground mining operations and produces multiple toxic gases as a result. The Mine Safety and Health Administration (MSHA) requires mine operators to measure the level of toxic gases in mines as frequently as necessary to ensure they are below regulatory safety limits. The current practice uses portable gas monitors to check the concentrations of toxic gases after a fixed post-blast time. This paper studies the application of a gas monitoring system in the return entry of a limestone mine to determine a safe re-entry time. The National Institute for Occupational Safety and Health (NIOSH) conducted such a monitoring program in a limestone mine from September 2016 through May 2018. NIOSH/PMRD (Pittsburgh Mining Research Division) is endeavoring to develop workplace solutions to improve detection of and reduce the risk of hazardous conditions. This study showed that the use of gas monitoring in the return air can be a useful tool at the mine operator’s disposal to detect and reduce the risk of hazardous conditions and also to reliably estimate the re-entry time.

By E. Farrokh

CSM and NTNU models are among the most commonly used models in TBM performance evaluation. Due to increasing application of TBM in different tunneling conditions, modification became necessary for these models. Sensitivity analyses on these two models indicate that both models are very sensitive to machine characteristics. Analyses performed on CSM database for cutter load and penetration rate prediction indicate while the r-square of the CSM model is reasonably high for the predicted cutterload, the r-square value for the penetration is low. In order to increase prediction capability of CSM model for penetration rate the model was reevaluated using non-dimensional analysis and the original database of Colorado school of mines. NTNU model is evaluated using Monte Carlo simulation and regression analysis. The results of analyses indicate that the majority of the variation of the penetration in NTNU model can be explained by only three parameters. This might indicate that the effects of other factors are overshadowed and it is worthy to reevaluate NTNU model using original database and more updated statistical methods to avoid overlapping of different parameters correlations.

Feb 23, 2014

By E. Ben-Awuah, H. Askari-Nasab, N. Al Habib

Open pit mines are getting deeper with time and transportation expenses are increasing because of the increasing haulage distance. In-pit crushing and conveying (IPCC) is getting popular in deeper open pit mines as a suitable alternative to truck haulage because it offers a lower operating cost due to shorter haulage distance and less truck requirement. Semi-mobile in-pit crusher, currently the most popular IPCC system, is relocated every two to five years and the short-term plan needs to be updated accordingly. Short-term planning with IPCC is an area of research that has not been explored extensively yet and hardly any model can generate short-term extraction sequence considering an IPCC in place. This research work proposes a mixed integer programming model to generate short-term production plan within a time horizon of 12 months. The objective of the model is to optimally allocate shovels to minimize cost of material handling and maximize revenue subject to meeting plant requirement, maximum allowable tonnage variation and IPCC location constraints to achieve production and NPV targets set by strategic plan. The proposed model has been implemented in a hypothetical case study for verification. The comparison of results between scenarios with and without IPCC is expected to justify the use of IPCC in large open pit mines from a short to medium term perspective. A semi-mobile IPCC system with one relocation is considered in the case study.

Feb 1, 2023

By R. A. Wyman

"The froth flotation process was patented by E.L. Sulman, H.F.K. Pickard, and John Ballot in 1906 . . . . . . . . . .James M. Hyde installed the first froth flotation process in the U.S., about August 1, 1911, at the Basin Reduction Co. plant, Basin, Montana . . . . . . . . . .By 1914, 42 mining companies were operating or experimenting with the flotation process . . . . . . . . . .The period 1930 to 1960 saw the application of flotation spread to nonsulphide ores and become the key factor in the economic production of many industrial minerals". So states FROTH FLOTATION, 50th Anniversary Volume, published by AIME in 1962. It is interesting, to observe that the Mines Branch, now part of the Canadian Department of Energy, Mines and Resources, was established in 1907 through an act of Parliament entitled, "The Nines and Geology Act". In 1911, a mineral dressing group was formed and a laboratory was constructed. By 1921, an engineer was devoting full time to industrial mineral processing problems.

Jan 1, 1971

By William G. Holroyd

In January 1992, the Office of the US Trade Representative announced that the People's Republic of China had agreed to protect US intellectual property, including computer software, sound recordings, agrichemicals and pharmaceuticals. Under the agreement, China will make significant improvements in its patent, copyright and trade-secret laws. Ambassador Carla A. Hills, the US trade representative, said "this agreement should create significant opportunities for US firms interested in marketing high valued-added products to China." Principal beneficiaries will include the agrichemical and computer industries, as well as pharmaceutical, entertainment. The agreement will safeguard these industries' intellectual property, stimulating new exports to China and helping to generate additional growth in the US. Refractory grade bauxite was included in the mineral category of the $1.5 billion of Chinese products on which the US government threatened to impose an immediate 100% trade tariff. Refractory bauxite is available from Guyana and Brazil at higher cost and in different grades. However, refractory brick manufacturers would have had little choice but to pass on the costs to their consumers. Although the United States and China are separated by political ideology and internal governing structures, this agreement recognizes the importance of a $19 billion trading relationship. Consequently, the renewal of China's most favored-nation trading status in the US congress in -June 1992 was all but assured. Many US companies doing business in China and Hong Kong have been quietly increasing their investments since 1989. These companies can now concentrate on developing sales to the domestic Chinese market. This market is expected to surpass 1.2 billion people in 1995 and approach 1.3 billion by the end of the century.

Jan 1, 1993

By A. Arik

Reliable ore reserve estimates for deposits with highly skewed grade disributions are difficult tasks to perform. Although some recent geostatistical techniques are available to handle problems with these estimations, ordinary kriging or conventional interpolation methods are still widely used to estimate the ore reserves for such deposits. The estimation results can be very sensitive to the search parameters used during the interpolation of grades with these methods. This paper compares the ore reserve estimates from ordinary kriging using several cases in which certain search parameters are varied. The comparisons are extended to different mineralizations to show the changing effects of these parameters.

Jan 1, 1990

By T. Emery, D. Sweet, J. Bourgeois, B. Seymour, D. Porter

Cemented rockfill (CRF) is being used to backfill primary and secondary stopes at the Eagle Mine, an underground nickel and copper mine operated by Lundin Mining. National Institute for Occupational Safety and Health (NIOSH) researchers from the Spokane Mining Research Division (SMRD) are conducting cooperative research with the mine staff to determine if the size of a CRF sample affects its measured strength properties. Based on previous research by NIOSH, cylindrical samples of CRF ranging in size from six to eighteen inches in diameter were cast at the mine and cured underground. The samples were later transported to the SMRD laboratory and the Michigan Technological University where tests were conducted to determine the strength and elastic properties of the CRF. To further analyze the relationship between backfill density and compressive strength, different ASTM International compaction techniques were used to cast the samples. For comparison, tests were also conducted on in-situ core samples that were drilled from a stope which had been backfilled with the same CRF mix. The data collected from this study not only improves our understanding of CRF in-situ properties but also helps optimize Quality Assurance/Quality Control (QA/QC) methods for backfill preparation and testing.

Feb 1, 2023

By Glenn J. Phillips, Debra L. Musick

The operating mine is dynamic, everchanging, and a continuous moving target. The only way to effectively manage such a creature is to be able to evaluate the cost of operation over short enough time periods that rapid effective controls can be implemented before loss can erode the marginal profits in todays market place. Such short term evaluations can provide the basis for the long range planning that can keep an operation healthy in the future. The spreadsheet programs on small computers (PC's) offer the possibility of such evaluation by accumulating data in a useable format, providing timely cost reporting and providing a tool for use in evaluating the day to day alternative choices of the real mining world.

Jan 1, 1987