Search Documents

By Robert L. Russell

The Bunker Hill Mine, located in the Coeur d'Alene Mining District at Kellogg, Idaho, has been a major producer of lead-silver-zinc ores since its discovery in 1887. The mine has produced over 29 million tons of ore from some 20 to 25 veins and ore zones, and now covers an area approximately one mile in length and one-half mile in width. The active section of the mine extends from 2500 ft above sea level to 1600 ft below sea level. Production is presently at the rate of about 1700 tons of ore per day. A two-mile adit, the Kellogg Tunnel, at the 2500 elevation, provides access to the main shaft area. Ore is hoisted to the adit level through a 5000-ft, 500-inclined shaft, extending to the lowermost haulage level 1200 ft below sea level. Primary shaft service for men and materials is supplied by three major internal, inclined shafts equipped with double-drum hoists. Present production requires ten levels to serve for mainline track haulage. These range up to 5000 ft in length and are either 200 or 400 vertical feet apart. Also, many intermediate levels exist throughout the mine. The conventional and autoloader mechanized square-set and cut-and-fill mining methods used throughout the mine have been the subject of a recent paper(l). One-third of current production is from vein-type ore bodies which are long distances from main shaft areas. Such veins generally dip about 450, have relatively narrow widths of from 3 to 20 ft, and usually contain less than 500,000 tons of ore. For many years, ore bodies thus situated have been developed by means of a separate inclined, timbered service shaft-raise connecting two or more main haulage levels. These commonly range from 400 to 1000 ft in vertical extent and are equipped with 25 to 50 hp electric, single-drum hoists. Intermediate levels are driven as conventional track drifts at 100-ft vertical intervals between the haulage levels. Ore and waste from the intermediate levels are trammed to orepasses for delivery to the lowermost haulage level servicing an ore body. The final result may be visualized as a number of small mines within a large mine. The problems of high development costs and high total development time, and the large amount and high cost of providing materials handl ing and ore haulage service while producing from this isolated type of stope block, made it desirable to consider totally new approaches in developing and mining a number of similar areas.

Jan 1, 1971

By Z. Rogovin

In order to develop more accurate procedures for scale-up and design of semi-autogenous-grinding mills through detailed mathematical models, a better understanding of the charge motion and rock/ball segregation is needed. To achieve this a 0.61 m (2.0 ft) diameter x 0.305 m (1.0 ft) length plexiglas mill was constructed as a scale model of a commercial SAG mill. Rock motion in the rotating mill was simulated using various sizes of ceramic balls. Quantitative measurements of dynamic angle of repose, water and slurry motion, holdup and size segregation of the charge were taken. In addition, a video-presentaiton (available to the public) was prepared to elucidate charge and water motion at various mill speeds, charge volumes, rock size distribution and flow rates.

Jan 1, 1985

By Susanne Pignolet

Ore microscopy has been applied to the complex lead-zinc-copper-cobalt-nickel ores from the Madison Mire in the Fredericktown subdistrict of the Southeast Missouri Lead District to predict potential beneficiation problems. It has been found that in some portions of the ore deposits, textures are present which may result in metal losses. In ores from the Bonneterre Transition Zone the intimate association of siegenite with chalcopyrite may result in cobalt and nickel losses to the copper concentrate. In ores from higher stratigraphic horizons, this association is relatively uncommon, and siegenite is commonly associated with bravoite. This latter association will increase the recovery of the cobalt and nickel in bravoite, even though some of the fine-grained bravoite will not be recoverable. Other textures which may result in potential beneficiation problems include coatings of covellite on chalcopyrite and inclusions of sphalerite in galena.

Jan 1, 1983

Since it was first introduced, the Coal Mine Roof Rating (CMRR) has been widely accepted as a tool for geologic characterization and mine planning. This paper discusses the application of the CMRR to another practical ground control problem. Extended cuts (cuts greater than 6 m (20 ft) in length) are commonly used with remote control continuous miners. Extended cuts can greatly increase productivity, but they have been associated with a number of fatal roof fall accidents. When extended cuts are attempted in weak roof, the roof may collapse before it can be bolted, causing hazardous conditions. Until now, it has not been possible to predict where conditions may not be suitable for extended cuts. In this study, data on the CMRR and extended cut experience were collected at 36 mines in 7 states. It was found that when the CMRR was greater than 55, deep cuts were routine in nearly every case. When the CMRR was less than 37, extended cuts were almost never taken. Between 38 and 55, extended cuts were feasible sometimes but not others. The data also shows that extended cuts are less likely to be stable if either the entry span or the depth of cover increases.

Jan 1, 1998

By Hans Smit

The face of mining as we know it is set to change in the very near future as mining companies all over the globe realize the implications of accessing the vast mineral wealth contained on, and under, our ocean floors. With some land based mineral deposits being fully exploited across the world, deep sea mining is set to revolutionize global approaches to the search for precious metals and other sought after minerals. [ ] Previously, the financial implications of deep sea mining outweighed the benefits of access to the mineral rich deposits identified all around the world. The process of marine diamond mining off the west coast of southern Africa started in the late 1950?s by a Texan, Sammy Collins, and subsequently continued by De Beers to the present day, has proven to be an excellent proving ground for the development of technology and mining systems that ensure a sustainable and financially viable business. [ ]

Jan 1, 2008

By A. Warren Wilson, Hugh R. Wilson

This paper describes the evolution of the Waste Management Program at the Lupin Mine through the years 1982 - 1986. Echo Bay Mines' Lupin Mine is located on the western shore of Contwoyto Lake in Canada's Northwest Territories about 80 km. south of the Arctic Circle. The gold mine commenced production in 1982 and the Waste Management Program was based originally on the total containment concept. Due to an expansion of the mill circuitry and increased throughput, it was apparent that total containment was no longer applicable and therefore studies were undertaken to characterize the tailings, to evaluate the effectiveness of natural degradation of contaminants in the tailings pond and to determine what additional treatment steps would be necessary to meet the requirements of the mine's Water Licence. These studies indicated that arsenic and cyanide concentrations in the tailings pond decant water would not meet Water Licence discharge limits unless certain measures were under taken. As a result of this work, in late 1984 a decision was made to create a two-ponds-in-series system and the necessary civil work was started in 1985. In addition, a series of dykes were constructed to contain the solids portion of the mill tailings in a confined area of the first pond. To remove cyanide, the ponds are operated in a sequential fill and decant mode to take maximum advantage of natural degradation. For arsenic removal, a chemical feed system was constructed for iron salt addition to the decant stream from the first to the second pond. Decanting of the ponds is accomplished by means of a series of 500 mm (20 inch) Sclairpipe syphons.

Jan 1, 1987

By W. Zhang

"The adsorption of collector on bornite has been studied in situ in aqueous solutions by applying an atomic force microscopy (AFM). The AFM images show that xanthate, such as potassium ethyl xanthate (KEX) and potassium amyl xanthate (PAX), adsorbs strongly on bornite mainly in the form of insoluble metal xanthate, which binds strongly with the mineral surface without being removed by flushing with ethanol alcohol. This adsorption mechanism is very similar to the one obtained with chalcocite/xanthate system. However, the result also clearly shows that the adsorption of xanthate on bornite is totally different from its adsorption on chalcopyrite, during which oily dixanthogen is the main adsorption product on chalcopyrite surface. The obtained AFM images also showed that the adsorption increases with increasing the collector’s concentration. When Cytec Aerofloat 238, a dialkyl dithiophosphate collector, is used, it adsorb on bornite mainly in the form of an oily substance, which can be rinsed off mineral surface by flushing with ethanol alcohol. AFM images also show that the adsorption of Cytec Aerofloat 238 increases with increasing the adsorption time. INTRODUCTION The adsorption of collector on mineral surface is vital for a successful flotation process to achieve a satisfying recovery. Historically, many works have been carried out to clarify the adsorption mechanism of collectors on sulfides. (Gaudin and Schuhmann, 1936, Poling and Leja, 1963; Allison et al., 1972, Fuerstenau, 1982; Leja, 1982; Woods, 1984) Compared to other copper minerals such as chalcopyrite and chalcocite, much less work has been done to study the adsorption collector on bornite. Allison et al. (1972) studied the reaction products of various sulfide minerals with xanthate solutions and reported that the measured rest potential of bornite in 6.25×10-4 M KEX solution at pH 7 was +60 mV and the reaction product of PAX on bornite was cuprous alkyl xanthate. Mielczarski and Suoninen (1984a, 1984b) applied the XPS and studied the adsorption of potassium ethyl xanthate on cuprous sulfide. It was reported that there was a relatively rapid formation of a well-oriented monolayer of xanthate ions followed by a slow growth of disordered cuprous xanthate molecules on top of this layer. Buckley et al. (1984) investigated the surface oxidation of bornite by linear potential sweep voltammetry and X-ray Photoelectron Spectroscopy and proposed the adsorption products on bornite depended on the solution potential. Zachwieja et al. (1987) studied the electrochemical flotation of the bornite-ethylxanthate system and reported that KEX reacted with bornite through an electrochemical oxidation reaction forming cuprous xanthate between -0.4 and -0.2v (SCE). Hangone et al. (2005) studied the flotation of a bornite-rich copper sulfide ore using thio collectors and their mixtures and reported that the highest copper recoveries were obtained with the diethyl dithiophosphate (di C2-DTP)."

Jan 1, 2016

By James S. Browning

Mica mining in the United States is confined largely to pegmatites and schists in a few well-defined areas. The largest region extends from central Virginia southward through western North and South Carolina, northern Georgia, and east-central Alabama. 1, 2, 3 Whereas in western North Carolina these pegmatite dikes are weathered to only a shallow depth, they are deeply weathered in the Carolina Piedmont and in Georgia and Alabama. Particularly in Georgia and Alabama, mica is found in the decomposed slates and schists adjacent to the pegmatites, and in deeply weathered granites. Most flake mica is obtained as the major marketable product by crushing and milling pegmatites.4 To a lesser extent, mica is produced as a byproduct of feldspars and spodumene.6 Past research by the Bureau of Mines has developed two methods for mica flotation. One method utilizes acid-cationic flotation for recovery of mica." This method requires thorough desliming of the ore with consequent fine mica losses. The other method utilizes an alkaline-anionic-cationic process for recovering fine size mica from pegmatite ores after desliming sufficiently to remove clay materials but not so drastically as to remove the fine mica. 8, 9, 10, 11, 12, 13 The latter process has also been successfully applied to a micaceous schist ore from California.14 This report summarizes the results of these research studies. Both of the flotation processes developed by the Bureau of Mines have been adopted by the mica industry and are being commercially utilized separately and in combination for flotation of mica from weathered pegmatite ores.

Jan 1, 1969

By William M. Kester

Finely sized Upper Freeport coals are beneficiated to reduce ash and sulfur using high-intensity magnetic separation to process both (1) raw, untreated coal as well as (2) raw coal which was pre-treated thermally with steam and air. Substantial, sulfur and ash reduction can be obtained using both approaches to magnetic beneficiation of coal fines, but evidence indicates that pre-treatment which would constitute a costly supplementary step is technically inferior to the direct beneficiation of raw, untreated coal. These bench-scale studies demonstrate that if high-intensity,; high capacity, dry, magnetic beneficiation equipment can be developed and' installed at coal burning power plants or at appropriate points in coal preparation plants substantial quantities of sulfur may be removable from coal after pulverization as a means' to reduce air pollution.

Jan 1, 1965

Underground mining alters ground condition, producing a disturbance in the ground water regime. The level of disturbance is dependent on the local hydrology, geology, and type of mining. Serious damage is sometimes caused by ground water- when mine roofs collapse, causing subsidence. Subsidence is either unplanned, where pillars are inadequate to provide support; or planned, where total extraction occurs over a large area. The primary objective of this study is to investigate the effects of mine subsidence on the ground water hydrology in the Warrior Coal Basin. Underground openings resulting from coal mining activities have been the most significant cause of subsidence problems in the Warrior Coal Basin, the main source of coal in Alabama. This problem will be even more serious in the future because 19 of Alabama's 24 billion tons of coal reserves are classified as an underground source (Tolson, 1982).

Jan 1, 1987

By P. Zhang, D. W. H. Su, M. Van Dyke, H. Dougherty

This paper describes the scientific data acquisition, data interpretation, and sophisticated 3-dimensional modeling processes of an ongoing gas well stability research program by the National Institute for Occupational Safety and Health (NIOSH). Results from the NIOSH field instrumentation programs and the parallel 3-dimensional numerical modeling programs indicate that overburden depth, overburden geology, surface topographic relief, strata dip of the coal measure rocks, and casing cementing alternatives are the dominant factors affecting longwall-induced subsurface deformations and gas well casing stresses. Topographic relief could produce localized longwall-induced deformations if weak-to-strong rock interfaces are present near the bottom of stream valleys. Strata dip has significant impact on longwall-induced subsurface deformations. Cementing alternatives are found to have significant impacts on longwall-induced deformations and gas well casing stresses.

By Mark E. Smith

To allow recovery of gold values from ore which cannot be economically processed by the mill, Pinson Mining Company has developed a run-of-mine heap leaching facility. In order to estimate production scale recovery rates, reagent consumption and percolation problems, a series of pilot scale tests were performed. These tests typically consisted of 3,630 metric tons (mt) (4,000 tons) leach ore at a grade of .94 to 1.56 grams per metric ton (g/mt) (.03 to .05 oz.) Au/Ton. Test heaps were loader stacked to approximately 4.3 meters (14 feet) high. Information from these pilot scale tests was employed in the design and construction of the production scale facility. Parameters such as spray rate, leach cycle, sprinkler placement, and barren solution chemistry were determined by the pilot tests.

Jan 1, 1983

By P. O. Lindahl

The U.S. Bureau of Mines initiated research to improve the safety and efficiency of transporting coal from deep underground mines using a balanced air-lift hydrohoist. A 50-m-high pilot-scale model was constructed and tested to evaluate the feasibility of hydraulically hoisting a coal-water slurry in a U-tube pipeline from the mine level to the surface with the assistance of compressed air. A prototype screw feeder is used to continuously compact and inject 5-cm or less run-of-mine coal into a pressurized 20-cm-diam pipeline. Production rates up to 40 metric tph at an airflow of 1.5 m3/min were achieved with the model, and coal size degradation was relatively minor. Modifications are in progress to achieve 100 tph at an airflow of 2.8 standard m3/min injected into the riser pipe. Pilot-scale results indicate that an air-lift hydrohoist system is a feasible, cost-effective alternative to conventional skip hoisting that can be installed in existing shafts or surface-drilled holes closer to the face area. Air-lift hydrohoisting offers advantages of infinitely adjustable slurry flow rates, reduced pressure at the point of coal injection, and flexible design that can be combined with hydraulic pumping. Proposed design changes are discussed for coal transport, mine layouts, ventilation, fire control, and escapeways using this system.

Jan 1, 1995

By J. M. Mercier

Approximately seven (7) years of recent intensive mining activity in the Wasatch Plateau Coal Field of Utah has revealed distinct geologic patterns which, at times, profoundly influence reserve estimates, coal quality, mine layout, and reserve accessibility. Mine planning, economic feasibility, and resource recovery activities by Getty Coal Company utilize a multi-faceted approach by necessity when evaluating Utah properties. Two specific operating mines offer examples of the affects of adverse geologic conditions on mine operation and project economics.

Jan 1, 1984

By M. Hancer

The sign of the surface charge of selected potassium soluble salt minerals namely KClO4 , K2SO4 , KNO3, and KCl was determined from nonequilibrium electrophoresis measurements and found to be negative for each of the salt. Dodecylamine flotation of these salts revealed that the concentration of amine required for flotation increases in the order KClO4< K2SO4< KNO3<KCI. Precipitation of the amine collector colloid was not required for flotation of the oxyanion salts and in this case it appears that adsorption of the dodecylamine cation is sufficient to create the hydrophobic surface state. The order for flotation is explained in terms of surface hydration of these respective potassium salts based on contact angle measurements and FT Raman spectroscopic characterization of water structure.

Jan 1, 1999

A linear programming model with integer sequencing variables is developed to schedule limestone production for a quarry in Central Japan. The model is used to optimize raw material production from the quarry supplying limestone to cement, quick lime and aggregate plants. Typically, the mining in the quarry takes place in four to six different areas each area having 3 or 4 mining increments. Each mining increment contains different quality of limestone. The limestone production from the quarry is transported to the plants byway of 3 ore passes. Each plant requires a given quantity of limestone per period meeting certain quality constraints. This paper will describe development of the scheduling optimization model and how it is used to schedule production by period within the quarry to meet the capacity and blending requirements of the plants.

Jan 1, 2003

By J. A. Herbst, C Lo. Y, Z. Rogovin

The identification and quantification of incipient overload conditions in mills have recently been found to be very significant in the design of tumbling grinding mills. To investigate these phenomena, a series of experiments was conducted in a Plexiglas mill operated in both dry and wet modes. For on-stream measurement of the mill charge weight, volumetric filling, dynamic angle of repose, and mill power, an electronic system was developed. The mill was filled to various levels with 19.1-mm (3/4-in.) ceramic balls as grinding media. As feed material, grindable limestone or 3.2-mm (1/8-in.) nongrinding ceramic balls were fed at various steady-state rates to determine the incipient overload conditions. The prediction of overload has apparently been reduced to predicting the feed rate that results in 50% mill filling.

Jan 1, 1988

By Ralph E. Magnuson

The quality of our environment is of great importance to all of us. Today, there is a great public concern about the degradation of our air, land, and water and the resultant slow death of our planet Earth. The miner has always been concerned with his environment. Historically, mining has been a part of the frontier. As a result, the miner has pioneered and developed many parts of the world. In the beginning, he had to hack out a place for his mine, himself, and his family. He was given accolades and praise for his accomplishments. Now, however, he is attacked as a ravager of the landscape. It was and is no different on the Marquette Iron Range in Marquette County, located in the Upper Peninsula of Michigan. Iron ore was discovered in 1845 and mining was begun by 1848. Over nearly 1 ¼ centuries, a total of 379,197,000 tons have been shipped to market. Ports, docks, railroads, and towns all had to be built in order to get that tonnage out to iron and steel makers. In those early days the environment had to be mastered, not pampered.

Jan 1, 1970

By Robert K. Jones

Filter media can be defined as that material which effects the removal of finely divided solids from a fluid. Thus the removal of dust from air or turbidity from water, for example, can be the result of passing the fluid through a properly supported filter media. Since filtration in one form or another has been practiced since pre¬historic times filter media have been made from an extremely wide variety of materials. Vegetable and synthetic fibers (used loose, or formed into papers, felts or cloth) sand, ground coal, diatomite, perlite, wire cloth, porous metal, and bonded aluminum oxide are among the more important materials used today.

Jan 1, 1961

By C. L. Karr

Researchers at the University of Alabama have developed a method for producing fuzzy linguistic models of mineral processing equipment directly from engineering data. These fuzzy linguistic models rely exclusively on data collected from the processing systems being modeled and do not presuppose an understanding of the physics of the system. The fuzzy linguistic models use descriptive rules and explicit membership functions that provide a precise, nonmathematical description of the processing equipment. A genetic algorithm is employed to simultaneously select rules and tune membership functions used in the fuzzy models. The result is an extremely flexible approach to modelling that is applicable in a variety of linear and nonlinear systems. The effectiveness of this approach to modelling is demonstrated using a four-input, two-output model of a grinding circuit.

Jan 1, 1996