Search Documents

By J. A. Murray

Maintaining satisfactory air quality in electro-winning tankhouses has been problematic and costly, particularly as plant operating current densities have increased. Conventional approaches, including the use of beads, hollow spheres, surfactants and coalescer devices, have not proved completely effective, requiring that powerful ventilation systems be installed. As workplace and environmental regulations become more stringent, containment of the acid mist at its source is more attractive. An electrode cap system based on this approach has been developed and tested in two commercial copper electrowinning tankhouses. The design, development, installation and cost of the new electrode cap system are described.

Jan 1, 1996

By T. A. E. Breen

A new high intensity grinding technology has been developed and is now being commercialized by Hicom International of Australia. This has led to the development and manufacture of Hicom 120 grinding mills which are now being sold internationally for a range of mining industry applications. The first commercial process application has been for the diamond sector, where the ability of the mill to remove host kimberlite rock by attritioning, with no damage to the thereby liberated diamonds, is seen to be a most beneficial attribute. There are, however, many other mineral industry applications for this mill.

Jan 1, 1999

By D. V. Bush

There has been a great deal of evaluation and discussion on the economics of semi- autogenous grinding versus conventional grinding circuits. This paper will not discuss the merits of one system over the other, but rather will discuss the Henderson Mill's approach toward achieving the most economical milling conditions in its existing SAG mills.

Jan 1, 1985

By K. P. Chong

Fracture toughness of oil shale is an essential property in fragmentation to optimize particle sizes and permeability distributions in in-situ processes. Fracture mechanics of oil shale has been based on conventional fracture mechanics using notched samples and assuming the material to be isotropic and elastic. Oil shale is a layered material more accurately characterized as transversely isotropic. The senior author proposes to use a semi- circular core specimen with a center crack subjected to three point bending. Singular crack tip elements with isoparametric elements are used. The precracked semi-circular disk is modeled under displacement loading. The effect of crack length on the non-dimensionalized stress intensity factor is investigated by strain energy method, ellipse method, and stress method. Very close agreements are found. The fracture toughness is obtained by compressing the specimen in to failure. Parameters such as oil yield are investigated.

Jan 1, 1984

By Ronald H. Mullennex

The growing need for development of thinner, more erratic, or less easily- mined coals in the Appalachian region requires more detailed analysis of conditions and factors controlling or influencing deposition of these seams. The value of depositional modelling in evaluation of such coals has been demonstrated in many recent studies and publications. Such modelling may be applied to allow prediction of factors varying from regional coal occurrence trends to very local areas of seam discontinuities, but requires thorough utilization of all available types of data. Mapping of general depositional energies, as derived from basic geophysical and driller's logs, can be applied to specific prediction of coal occurrence, and projection of particular facies as representative of unique depositional features or conditions often proves more applicable to coal character delineation than does mapping of the coal itself. Depositional modelling and trend projection may also serve as a guideline in reserve classification and confidence-levels in reserve estimations.

Jan 1, 1981

By William F. Abercrombie

The role of the laboratory is described in relation to the prospecting and exploration of kaolin clays. Test methods used to evaluate crude ore samples of kaolin clay for commercial consideration are reviewed. A background of the kaolin mineral and known means of prospecting this mineral are presented. Common analytical methods are discussed with special emphasis on those in use today.

Jan 1, 1982

By G. Van Weert

Refractory ores and concentrates containing silver tend to form Ag-jarosite during autoclave oxidation. Silver extraction from the oxidation products is therefore low, unless a hot lime treatment step to decompose Ag-jarosite precedes cyanidation. Since silver iodide is very stable but soluble in cyanide solutions, the formation and decomposition of Ag-jarosite in the presence of iodine species was studied. Results indicate that Ag-jarosite formation could be prevented in favour of H3O-jarosite and AgI while oxidizing Ag2S under industrial autoclaving conditions, when the total iodine species to Ag mole ratio exceeded 5. Lower ratios gave proportionally more Ag-jarosite and less AgI. Under these conditions existing Ag-jarosite was also found to decompose in H30-jarosite and AgI.

Jan 1, 1993

By Ronald M. Tipton

Freeze and thaw deterioration is a serious problem In con¬crete pavements. The main cause of distress Is thought to be the pore structure of coarse aggregate. In an attempt to characterize deleterious pores, the Iowa Pore Index test and the Expected Durability Factor, as Calculated from the mer¬cury intrusion porosimeter, were devised. This study Included freeze-thaw and sodium and magnesium sulfate soundness testing of sixteen carbonate aggregate samples. In addition, the Iowa Pore Index and the Expected Durability factor were determined for each of the samples. All of the Above mentioned physicochemical parameters were examined using bivriate correlation analysis with the In¬tent to evaluate the effectiveness of the Iowa Pore Index and Expected Durability factor for predicting the frost dur¬ability of an aggregate. The results from the bivariate correlation analysis showed no significant correlation, between the Iowa Pore In¬dex And- Expected Durability factor with the other physico¬chemical parameters investigated. Rust interesting is that the Iowa Pore index predicted that All of the tested samples would resist freeze-thaw failure, whereas the Expected Durability factor predicted that -ash sample would he non-durable.

Jan 1, 1987

By Alessandro Boscaro, Daniele Martinelli, Cristina Gabriela Oñate Salazar, Daniele Peila, Carmine Todaro

"The wear phenomenon in TBM machines is not a simple issue, as many parameters are playing an important role on the consumption of the tools during a tunnel excavation. The action of the wear due to the contact with the soil can occur on the excavation tools, on the cutterhead, in the excavating chamber and on the screw conveyor. The test developed at the Laboratory “Tunnelling and Underground Space Center” of the Politecnico di Torino is aimed to reproduce the interaction between the tools and the excavated material, simulating the excavation conditions in terms of soil conditioning and water content. The test, which is not standardized, is studied to evaluate the wear in a global point of view. The present work starts by testing the influence of the use of chemical agents during the conditioning phase on the drop of the wear phenomenon, in terms of metal weight loss. 1. INTRODUCTION The wear phenomenon of the excavation tools used in TBM tunneling machines is playing recently a major role in the design stage of full-section tunnels in both soils and rocks. Concerning EPB excavation technology, the main issue regarding productivity is the wear of its components (Peila et al.,2012), which increases the so called dead time in the whole process. The friction generated between the components and the ground causes the consumption of the tools and other metallic components in contact with the ground, described as primary and secondary wear by Nielsen et al. (2006a). This leads to downtime, with risky and complicated maintenance operations (Peila and Schulkins, 2009), as occurred in recent tunneling works in Liguria (Italy). The study of this argument in granular soils is very delicate, as it encloses not only the properties of the excavation tools, but also the characteristics of the ground to be excavated (hardness, mineralogy composition, shape and dimension of the particles and moisture content). The penetration mechanism is based on the scraping of the ground, by mean of cutting tools, with its consequent consumption. Concerning the rocks, the excavation principle is characterized by crushing the rock mass matrix by applying high compressive stresses through cutting disks. In such a way, to avoid frequent downtimes and their consequent economic losses, it is very important to study this subject and therefore understand and forecast the durability of the components, in order to try to maximize the productivity of the machine by reducing the frequency of maintenance stoppings."

Jan 1, 2016

By Donald Bishko

Zoning is the legal means by which land use can be controlled. Although zoning laws have historically been quick to prevent quarrying, one is hard pressed to find zoning ordinances which specifically state that land should be used (or held in reserve) for quarrying and prevent other uses such as recreation, housing, etc. This situation is especially true when the mineral to be quarried has a low intrinsic value such as sand, gravel, and crushed stone. The chance of a gold mine surviving urban sprawl is probably considerably greater than that of a sand and gravel pit, even though it is possible that the dollar value of the sand and gravel' would exceed that of the gold mine. The research reported herein was concerned with two major topics: to delineate the real costs associated with the non-protection of our construction aggregate resources (growth minerals) and to develop a computer simulation model which would aid planners in making economically sound decisions. This paper describes the problems faced by the mineral aggregate industry and discusses the role of computer simulation in planning problems. It briefly describes a simulation model which has been developed and previously reported12 and discusses the results of a pilot study conducted on the Tri-City area (Albany, Schenectady, and Troy, New York). 3

Jan 1, 1970

By N. S. Tanious

The Nuclear Regulatory Commission (NRC) regulation 10 CFR 60 requires that the ventilation system for the geologic repository be designed to: (1) control the transport of radioactive particulates and gases, (2) assure continued function during normal operations and under accident conditions, and (3) separate the ventilation of excavation and emplacement areas. The ventilation system design should take into account thermal loading; maintenance of the retrieval option and-the separation of the development and emplacement ventilation circuits. An analysis was performed by NRC's contractor, Engineers International on the ventilation system design described in the Department of Energy's conceptual design for Nevada. The ventilation analysis is of a preliminary nature. The conclusions presented in this paper reflect the views of the authors and may not represent the views of the NRC. In this analysis, available Nevada Nuclear Waste Storage Investigation (NNWSI) ventilation design information was reviewed and a ventilation network analysis was performed.

Jan 1, 1988

By O. A. Velasquez, A. R. Kumar

"Dust generated on underground mechanized coal mining faces is a health and safety hazard. Continuous miners deployed underground usually have an integrated flooded-bed dust scrubber mounted onto the machine that arrests the generated dust from close to the face and cleanses the air around it. However, the impingement screen might get clogged depending on the coal seam being worked. This necessitates the cleaning of the screen which in turn, reduces the overall availability of the scrubber and, hence the continuous miner. A novel non-clogging screen has been developed at the Department of Mining Engineering, University of Kentucky. The proposed impingement screen is built up of three individual aluminum screen units 1.5 mm thick and separated by 3 and 2 mm respectively. The screens have long vertical slits measuring 6 mm. A water spray continuously keeps the screen wet and provides for the filter element to arrest the dust particles. The slits force the dust-laden air to make sharp turns. The dust particles cannot change directions rapidly, impact one of the three screens and are separated out based on their momentum. Preliminary computational fluid dynamics (CFD) models have indicated significant cleaning efficiencies in the respirable range at the expense of much lower pressure drops. Results indicated by CFD models and supported by laboratory experiments have been discussed in this paper.ACKNOWLEDGEMENT The authors acknowledge the National Institute for Occupational Safety and Health (NIOSH) for funding this research. Dr. Thomas Novak, Professor of Mining Engineering, is also acknowledged for his continued support and encouragement. INTRODUCTION Continuous miners are ubiquitous in coal mining around the world. The miners are operated against bling headings, ensuring adequate flow of air at the face could be difficult. The minimum requirement of ventilation airflow quantities at those coal faces are legislated to dilute dust generated to harmless levels. New dust rules promulgated recently have further called for lower exposure levels of personnel working underground (Courtney) (MSHA, 2014) (NIOSH, 2010). Water sprays are also installed at strategic locations and serve as powerful air-movers. The sprays capture some amount of dust generated while cutting. In addition to this, usually, all continuous miners are equipped with a flooded-bed dust scrubber as shown in Figure 1 to capture the dust from close to the extraction drum (Chao & De-sheng, 2000) (Wala, Vytla, Huang, & Taylor, 2008) (Organiscak & Beck, 2010)."

Jan 1, 2018

By Z. Man, X. Zhu, Y. Xian, Y. Tao

"Fine coal separation has been always concerned. The froth flotation is not efficient in desulfurization because of the low rate of sulfide liberation from raw coal, the natural hydrophobicity caused by sulfur concentration on the surface of sulfide, and the presence of large amounts of middling feed. An efficient centrifugal gravity separator was employed to separate for Shandong –0.5mm high sulphur coal, the partition curve of centrifugal separator was obtained with conclusion that the Ecart probable error value of the separator is 0.095, the imperfection I value is 0.128. Finally, comparing with the coal flotation using progressive release method, the result shows that the effect of the desulfurization with centrifugal gravity force field based on density difference between coal and minerals are much better than that of the floatation which operates based on the difference in surface properties. It provides a efficient technical way for fine coal separation. INTRODUCTION Coal plays the most important role in the energy consumption in China. Although natural gas, wind energy, nuclear power has made great progress in recent years, but the share of coal in the final energy consumption accounts for 70-80%, which is determined by energy storage of China. Under the requirement of environmental protection, the clean utilization of coal resources becomes more and more important, and the need has already been identified. Coal washing and processing plays an important role in the process of high-efficiency and clean utilization of coal. For the separation of fine coal, flotation is a traditional method for effective separation and has been used in large scale industrial applications in coal preparation plant. However, for the separation of difficult-to float coal, especially fine oxidized coal and low–rank coal with hydrophilic surface, flotation is usually inefficient [1-3]. Although many pretreatment methods have been adopted, including grinding, microwave pretreatment, new flotation reagents, the problem of efficient separation has not been completely resolved [4-6]. Thus, an enhanced gravity separation method using particle density difference rather than hydrophobic difference was proposed for the separation of fine coal. Many research results have proved that this is a practical and effective method of sorting. R.Q. Honaker used Falcon C10 concentrator, Knelson centrifugal separator and spiral separator to clean the fine coal with size of 600*210 µm and 210*37µm, the effects of different operating parameters on the separation index was discussed. The results show that the separation density of Falcon can reach 1.6, and the Ep value can reach 0.1-0.15. This paper revealed that for the separation of fine coal with high sulfur content or fine grained content. Falcon has high separation efficiency with low cost. Separation results present in another paper showed that the desulfurization efficiency of inorganic sulfur was better than that of flotation [7-8]."

Jan 1, 2017

By P. Zhang, W. D. Xiao

"A process mineralogy study was conducted to guide the development of a process for the extraction of vanadic oxide (V2O5) and aluminum compounds from bone coal and its ash as well as the production of byproducts. Results show that to extract the targeted metals at higher recovery rates, one must find a suitable agent capable of destroying the structure of the mica and breaking down the lattices in which these metal-bearing minerals occur. For such minerals, metal extraction efficiency is usually low if the approach is simply adding an oxidant that cannot destroy the structure. In this research, a byproduct fluosilicic acid (H2SiF6) at 20 percent concentration from an operating phosphate fertilizer plant was found to be powerful and effective for the leaching of vanadium-bearing minerals such as mica. This environmentally friendly process improved the leachability of valuable constituents in the bone coal significantly, with the leaching rate of V2O5 increased to 94 percent, from 83 percent, and that of aluminum oxide (Al2O3) increased to 75 percent, from 40 percent. X-ray diffraction and chemical analyses showed that the structure of mica can be destroyed using fluosilicic acid either alone or in combination with sulfuric acid. Based on the process mineralogy study, a processing flowsheet was tested, which resulted in a final V2O5 powder product with purity of 99.2 percent and an overall recovery rate of higher than 85 percent. The flowsheet consists of leaching, ion exchange and ammonium precipitation. With this process, various byproducts could also be generated, including aluminum fluoride, cryolite, aluminum sulfate, calcium sulfate, ammonium chloride, sodium chloride and cement admixtures.IntroductionVanadium is an important rare metal broadly used in the production of steel alloys and nonferrous alloys as well as in the chemical field as a catalyst. Vanadium-bearing bone coal and clays are abundant in China, and they contain other valuable metals such as aluminum. Bone coal is a type of carbonaceous shale. The vanadium-bearing minerals mainly exist in mica, kaolin, iron oxides, tourmaline and garnet. According to previous studies (Xiao, 2007; Xu, 1989; Xu and Chen, 1991; Ji and Xu, 1991; Chen and Xu, 1992; Xu and Heng, 1992), vanadium occurs from the isomorphous substitution of V3+ for Al3+ or Fe3 + in the crystal lattices of mica, tourmaline, garnet, dolomite and aluminosilicate minerals. In iron oxide and kaolin minerals, vanadium appears as an adsorption form. The isomorphous substitution of vanadium is more stable in tourmaline, garnet and silicate minerals. Therefore, vanadium in bone coal may exist in three phases: vanadium-containing kaolin and oxides, vanadium-containing mica, and tourmaline and garnet (Xu and Chen, 1993; Xu and Zhang, 1993; Xu and Wang, 1994; Feng, et al., 2005; Lin and Fan, 2001)."

Jan 1, 2015

By N. W. Stump

New developments in on-stream analysis using immersed radioisotope gauges including results from plant installations are described. The control of grinding and flotation using a small digital computer has been complemented by this development. A control scheme for grinding which is based on maximum throughput at constant product size and preliminary work in flotation control are also outlined.

Jan 1, 1974

By J. A. Organiscak

This paper describes the research con-ducted on bit wear and respirable dust generation conducted by the US Bureau of Mines (USBM) and West Virginia University (WVU), a member of the Generic Technology Center on Respirable Dust. The USBM investigated wear, energy and dust characteristics of various conical bit designs when cutting rock. WVU studied the functional relationships between wear, cutting force, energy, and dust of one conical bit type when cutting coal. The objective of the USBM study was to identify qualitative bit selection guidelines for cut-ting rock; WVU's research objective was to determine optimum bit replacement guidelines. These research studies both found that bit geometry (a function of bit design and wear) influences energy consumption and dust generation. Bit selection and replacement recommendations are given.

Jan 1, 1995

By L. C. Lang

Effective and profitable mining begins with good blasting results. While the importance of sufficient energy to break the rock is recognized, more attention should be paid to the time factor in blasting. Fragmentation, looseness and the shape of the muckpile can be improved and energy levels lowered through the use of proper delays. The long delay is also the most important parameter in establishing stable walls along the final limits of the pit. The time factor in blasting is explained through the rock acceleration process and its practical application is demonstrated by case histories.

Jan 1, 1981

By T. M. Gurr

In response to concerns voiced by local, state, and federal agencies and various environmental groups, the Central Florida Phosphate Industry and various governmental agencies have been investigating methods to accelerate the consolidation of waste clays generated during phosphate washing and beneficiation processes. The objectives of research efforts have been to reduce the storage volumes required for clay waste, accelerate reclamation and to return the land to approximate pre-mining topography. Government and industry research to accelerate waste clay consolidation has evolved two general methods: gravity thickening and chemical flocculation. Gardinier, Inc. one of the phosphate mining companies, evaluated the use of synthetic (polyacrylamide) flocculants as an alternate waste clay thickening method in response to mining conditions encountered at their Fort Meade Mine and the proposed North Hardee County extension of the Fort Meade mine (Figure 1). After considerable research and evaluation, the Alsthom-Atlantic Clariflux Super-flocculation method was chosen by Gardinier, Inc. as a method to seriously consider for use at their Fort Meade mine.

Jan 1, 1986

By A. D. Davis

This project took a watershed approach in the evaluation of water-quality impacts from past mining activities and current restoration projects in the Bear Butte Creek basin, a small and well defined drainage in a heavily mineralized area of the northern Black Hills. The basin contains numerous inactive and abandoned mines as well as a currently active heap-leach surface gold mine. Bear Butte Creek normally loses all of its discharge to sinkholes in the Madison Limestone aquifer and thus can affect the water quality of this regionally important water resource. Water-quality data were analyzed, stream surveys were conducted, and two abandoned mine restoration projects were monitored to evaluate the effectiveness of the watershed approach and to identify practical remediation techniques that could be applied to other watersheds. A geographic information system (GIS) was developed to organize information on stream quality, abandoned mine locations, and other geologic and hydrologic data. The watershed approach toward assessing and reclaiming abandoned mines appears to be effective when compared to a point-source approach that might improve water quality at specific sites but not result in significant overall improvement to the watershed because of adjacent sources.

Jan 1, 1997

By Thomas H. Ferrigno

Modern Plastics (July, 1983) reported that about 2.2 million tons of mineral fillers were expected to be consumed by the plastics industry that year, of which 7096 was limestone derived. The combination of fillers and polymers is called a composite and, in the more general sense includes continuous and discontinuous components in a matrix. The only significant technical advance in the fillers industry has been the greater general availability of surfied (Ferrigno 1959), an acronym for surface modified, fillers. The many reasons for this occurrence will be given in detail later, but the primary reason lie with differences between inorganic filler surfaces and the polymers which bind them together to form the composite. Minerals and glasses (fiberglass, fly-ash and beads) have surface tensions in excess of 200 dynes/cm, whereas organic materials have surface tensions less than 75 dynes cm. Water has a surface tension of 72 dynes/cm and is always present as an absorbed layer on high surface tension materials to reduce the surface tension. Although almost any organic liquid or polymer has a surface tension low enough to displace the water layer, the highly polar nature of filler surfaces requires highly polar agents to produce a permanent effect, and frequently the water is so tightly bonded or so much more active that the displacement is temporary. Furthermore; the water layer causes tiny particles to adhere to each other (agglomerate) to make sepaartion or dispersion of the individual particles very difficult. The solution to these problems is then to form a chemically bonded layer on the filler surface similar to that of the polymer so that immediate wetting, dispersion and uniform distribution of the filler particles is obtained.

Jan 1, 1985