Search Documents

By R. D. Stewart

Abstract. Induced fluorescent sorting is a means of beneficiating an ore by selective labeling with a reagent combination which fluoresces when activated by ultraviolet light The reagent combination normally consists of a surface active compound and a fluorescent dye. The surfactant adheres selectively to a specific surface and carries the dye with it. Upon activation with ultraviolet light, the labeled pieces, in the size range 1.27 cm to 20 cm (0.5 to 8 in.), are detected during free fall by photosensitive cells and ejected by water jets. Either ore or gangue may be labeled.

Jan 1, 1980

By K. E. Harrison

Acid rain legislation as proposed by President Bush [1], if enacted, will immediately refocus current thinking on the economic decision-making as related to coal preparation facilities. Unit operations currently ignored because of their costs, will become mandatory to coal plant designers and operators to ensure maximum energy recovery and sulfur reduction in the entire coal stream. In anticipation of this need, the U.S. Department of Energy, The Ohio Coal Development Office, EPRI and others are sponsoring research in several areas of coal preparation, and coal plant designers are beginning to consider more innovative techniques as they configure their flowsheets for plants of the future. Preparation plants then will have recleaning

Jan 1, 1990

By Charles T. Holland

The tonnage produced on mechanized automated retreating longwall faces in the United States is growing rapidly. This time last year some 14 faces were operating, and in addition to that, three were known to be down looking towards revision or repairs before being placed back in service. These, it is believed, are now in service. It is estimated at the present time, therefore, that somewhere between 20 and 25 faces are being operated in the country. A survey made last year by the School of Mines, West Virginia University, indicated that longwall mining in general has been beset with a great many problems, some more serious than others. The problems that we propose to discuss here are those pertaining to roof and floor trouble in the tailgates. Longwalls are operating in this country at the present time under an overburden ranging from 200 feet to nearly 3000 feet. Main and tailgate entries are operating in panels of up to five each, with the width of the pillars between these entries varying from 20 to 50 feet. Face lengths are running from 270 feet to 670; actually a face 800 feet long should be possible. The most economical face is often spoken of as being around 450 feet.

Jan 1, 1969

By John W. Leonard

The typical tunnel boring machine in use on today's tunnel project uses 15'2-inch diameter cutters at a nominal load of 45 kips per cutter. The cutterhead rotates at a speed of 120 over D revolutions per minute where D is the cutterhead diameter in feet. The typical machine operates about 50 percent of the time. Delivery of a new machine takes 12 to 15 months. The TBM is a specialized tool and not applicable to all jobs. There is a range of job conditions that limit the economic use of a TBM. The machine should provide a thrust per cutter at least twice the compressive strength of rock in psi and up to three times the rock strength is required if in "granitic rocks." The rock strength in psi must be at least three times the cover above the tunnel in feet or the machine may stick. For example, 2,500 feet of cover requires at least 7,500 psi rock to avoid problems. When the RQD's over a significant distance of the project are less than 50, the TBM becomes support-bound. When a large percentage of the time is spent waiting while the ground is supported, the TBM cannot perform well (See Figure 1). This problem increased inversely with tunnel diameter. We are finding that increasing the RPM's does not significantly increase progress. The increased RPM results in a substantial decrease in cutter penetration. The explanation for this decrease appears to be vibration, cutterhead drag, or lack of stiffness in the cutterhead (See Figure 2).

Jan 1, 1981

By A. Röttger, W. Theisen, J. Küpferle, M. Alber

"Wear of TBM tools significantly affects tunneling advance rates. Wear-prediction models are based (amongst others) on the abrasivity of the present geology, which is determined via laboratory tests. To evaluate the results from such tests in context, this work considers the tribological system TBM tool from a materials technology perspective. In so doing, the microstructures of different application-oriented materials are presented and discussed in terms of their wear behavior and wear resistance. The significant influence of tool materials on the abrasivity of the geology and thus wear prediction models has already be identified. LCPC, Cerchar and nano-scratch experiments have been performed as confirmation. Material-dependent wear mechanisms and their correlation in terms of tunneling have shown that it is mandatory to consider the complete tribological system to estimate the wear of TBM tools. 1 INTRODUCTION Mechanized tunneling is vital to ensure necessary infrastructure development in megacities like Tokyo (Bay Tunnel), Istanbul (Eurasia Tunnel) and Mexico City (Tunnel Emisor Oriente). The use of Tunnel Boring Machines (TBMs) has been established for many years. In contrast to other methods such as boring and blasting or excavation using dredgers, tunneling with TBMs allows simultaneous excavation and removal of both the mineral and tunnel lining by tubbing segments or shotcrete. This makes tunneling more efficient, allowing for faster development of the tunnel in both hard rock and soil [1]. When budgeting such tunneling projects, precise planning and coordination in terms of tunneling technique choice (e.g. EPB or Slurry-shield), the relevant geology, and the associated penetration rates and tool wear are required. In particular, wear to TBM tools has a significant impact on tunneling progress. Due to wear, tools become dulled or lose their functionality because of brittle material behavior, thus reducing penetration rates and therefore tunneling efficiency [1]. As a result, additional tool changes are necessary, leading to higher overall costs due to down times and maintenance costs. Therefore, there is strong interest in a reliable and precise wear prediction model for TBMs. As already mentioned, the geology and associated wear of the tunneling tools define the maintenance times."

Jan 1, 2016

By D. M. Hausen

A quantitative x-ray diffraction method has been developed for the analysis of alteration minerals in wallrock. Alteration data are plotted and contoured (analogous to geochemical data). Alteration trends outlined by this technique correlate closely with geochemical anomalies, and in some cases attend well beyond the perimeter of anomalous base metal values. "Monomineralic contouring," applied originally to porphyry-type mineralization, has been extended to other types of mineralization, including volcanogenic massive sulfide deposits. Equipment and techniques used in the quantitative measurement of alteration mineralogy are discussed.

Jan 1, 1978

By E. J. Wade

My subject is gold price forecasting and monitoring as an important aspect of gold marketing. While I 'm specifically addressing gold, it is understandable that many other commodities could be readily substituted. Gold marketing must be studied as three distinct processes, and it is my intention to cover each of these processes in turn. First I?ll cover the process of gold price monitoring and forecasting in some detail. In order to select a method, or combination of methods, to be used to sell gold a determination of the future price profile is essential. The profitability of the sales effort will be determined, to a large extent, by how accurately the future price behavior of the gold market has been forecast.

Jan 1, 1985

By William R. Nash

Case histories of water problems in underground mine shafts and tunnels are outlined to illustrate varying degrees of sophistication in grouting techniques currently applied in such construction. The interception of water underground can be one of prior knowledge, i. e., the site investigation provides necessary data to plan a grouting program prior to construction start, or excavations may encounter "changed conditions" or unplanned water. The latter includes catastrophic inflows and emergency situations where the structural integrity of a building or concrete shaft lining are jeopardized. The presentation of this paper outlines some applications of grouting work in underground mine construction throughout the United States in a variety of geological provinces and for a variety of minerals.

Jan 1, 1984

By George H. Davis

The Caribou sulfide deposit near Bathurst, New Brunswick (Figure 1) is illustrative of one variety of strata-bound sulfide deposits. It consists of numerous near-vertical sulfide lenses which are concordant to the foliation and lithologic layering of low-grade metamorphic host rocks. Pyrite is the chief mineral in these lenses, but appreciable quantities of sphalerite, chalcopyrite, and galena are also present. Rocks in the Caribou mine area belong to the Tetagouche Group of Ordovician age. They consist chiefly of (1) quartz-sericite and quartz- sericite- feldspar schists, (2) greenschists, and (3) slate and phyllite. The trends of these steeply dipping rocks define the trace of a tight, steeply plunging fold structure, the Caribou fold (Figure 2). This fold plunges approximately 750 to the north-northwest; its axial plane strikes N.20°E. and dips steeply westward. Sulfide lenses of the Caribou deposit are associated spatially with the Caribou fold. The deposit is located in the fold along the contact between quartz-sericite and quartz-sericite-feldspar schists on the hanging wall and quartz-chlorite-sericite phyllites and graphitic schist on the footwall (Figure 3). Genesis of the Caribou deposit is ambiguous because its strata-bound form suggests syngenetic sulfide deposition, whereas its location within a fold suggests structurally controlled epigenetic mineralization. Acceptability of a particular genetic model rests on establishing the time of mineralization relative to deposition, deformation, and metamorphism of the associated rocks. To establish the timing for Caribou mineralization, the deformational histories of rock and sulfide, respectively, were compared. Epigenetic and syngenetic models can be tested against this interpreted structural history of the Caribou deposit.

Jan 1, 1971

By C. Heckman, M. S. Moats, A. Luyima, W. Cui

"Cyclic voltammetry, electrochemical impedance spectroscopy (EIS), and galvanodynamic and chronopotentiometric techniques were used to characterize the effects of DXG-F7®, a commercial smoothing agent, on copper electrodeposition onto 316L stainless steel from a synthetic electrolyte containing 40 g/L copper (Cu2+), 160 g/L sulfuric acid (H2SO4) and 20 mg/L chloride (Cl-) at 40oC. The findings were compared against results using HydroStar® 4208, a modified polysaccharide. The nucleation overpotential and plating potential observed in cyclic voltammetry and galvanodynamic testing showed that neither DXG-F7 nor HydroStar significantly polarized acidic copper electrodeposition. Subtle differences between the additives were found during EIS testing and modeling, but more research will be needed to fully understand these differences. Surface-roughness measurements of two-hour deposits indicate that DXG-F7 and HydroStar produced smoother deposits as their concentrations in the electrolyte increased. No difference in the surface roughness of deposits was detected between the additives. Based on the experimental evidence resulting from the laboratory testing, no significant difference was found between DXG-F7 and HydroStar at 20 mg/L Cl- concentration, with the exception that DXG-F7 dissolves more easily in water than HydroStar. Introduction Cathode deposits obtained from acidified copper sulfate electrolyte(s) without organic additives are often soft, coarsely crystalline and nodular (Sun and O’Keefe, 1992). Therefore, small amounts of organic additives are added to the electrolyte to produce level and dense cathodes during copper electrowinning. The action of organic additives is thought to be due to their adsorption on the surfaces of the newly formed copper grains. Hence, any copper grain that grows excessively fast adsorbs a layer of organic additive, which inhibits growth. The result is a smoother and harder deposit of suitable purity (Sun and O’Keefe, 1992). In part I of our four-part series on the examining of copper electrowinning smoothing agents, a review of previously published work on organic additives used during copper electrowinning was presented (Moats, Luyima and Cui, 2016). In the review, it was noted that many tankhouses had switched from guar to other saccharide-based products such as HydroStar and DXG-F7."

Jan 1, 2016

By R. C. Milici

Historical production data and reserve decline rates can be used both to predict future coal production rates and to estimate when the reserve will be depleted. Reserve estimates inferred herein from historical production data and decline rates are commonly lower than estimates made from geologic data. The latter include significant amounts of lower quality (deeper, thinner, higher sulfur) coal which may be mined when the better deposits are depleted.

Jan 1, 1997

By C. R. DeGennaro, M. R. Girman, J. Bickson, J. P. Homer, C. C. Jobes

Between 2005 and 2021, a NIOSH internal review showed that haul trucks were involved in 54 incidents at surface mines in the United States. Haul truck collision warning and avoidance systems (CXS) can assist in preventing accidents at surface mines. CXS use technologies to detect people or objects and alarm to alert haul truck operators. Robust testing can help ensure that they detect objects without excessive false positive alarms. Testing and validation would increase confidence in and encourage implementation of a CXS. Researchers from the National Institute for Occupational Safety and Health (NIOSH) reviewed documents related to the evaluation and validation of CXS with two objectives: (1) to identify methods and parameters used to evaluate detection performance and (2) to identify gaps in CXS test methods and in detection performance. Stakeholders can use the findings from this research to guide implementation of CXS to improve safety at surface mines.

Mar 2, 2022

By Kevin Lofftus

The rest potentials of molybdenite electrodes are measured as a function of pH in absence and presence of flotation reagents. The chemicals used include sodium ethyl xanthate, kerosene, dextrin,sodium hydrosulfide, hydrated sodium molybdate, sodium sulfate, and hydrated sodium thiosulfate. The effect of dissolved oxygen is also noted. The obtained data are correlated with the results of micro-flotation tests obtained under similar chemical conditions.

Jan 1, 1984

By Jun Yuan

Kaolin clays from five different commercial deposits in Georgia were studied to understand the variations of zeta potential and related fundamental properties. The results suggest that higher negative zeta potential is related to exchangeable or soluble calcium ions in the clays.

Jan 1, 1997

By Garry W. Warren

The electrochemical oxidation of chalcopyrite in the absence of-a chemical oxidant was studied in ammonia/ammonium sulfate solutions by anodically polarizing electrodes prepared from massive chalcopyrite. The effects of pH, cupric and ammonia ion concentration were systematically evaluated. Kinetic parameters were obtained from the anodic charge-transfer regions of the anodic polarization curves. Increasing ammonia and hydroxyl ion concentrations increased the rate of oxidation. A mechanism is proposed which explains the first order dependence of (NH3) and (OR) associated with a single electron transfer process. An empirical relationship which accurately describes the dependence of the rest potential (i.e. zero current potential) on solution composition is also given.

Jan 1, 1978

Using a Mark IV surface force apparatus, adsorption of dodecylamine hydrochloride on mica has been studied at pH 5.7 in the presence and absence of octanol. With amine alone, the repulsive forces between mica surfaces are reduced due to charge neutralization and attractive hydrophobic force; however, the latter is of relatively short-range with its decay length less than 2 nm. In the presence of amine and octanol, the hydrophobic force becomes more significant, its decay length being extended up to 6.5 nm. The increased hydrophobicity in the presence of octanol is attributed to the co-adsorption of the neutral surfactant with dodecylamine, which increases the packing density of hydrocarbons on the mica surface. The increased hydrophobicity due to co-adsorption is reflected in the improved floatability of silica when using octanol as an extender.

Jan 1, 1993

By R. Mensah-Biney

The adsorption of gold-thiourea complex onto a cation exchange resin, Amberlite 252, has been evaluated in a batch stirred reactor. The observed non equilibrium saturation capacity was 3.20 meg Au/g dry resin (620 kg/t) whereas the equilibrium ion exchange capacity was only 0.53 meq/g (103 kg/t). The enthalpy of adsorption was 4 -25 kJ/mole under equilibrium conditions and increased to 20-200 kJ/mole under non equilibrium conditions. Under non equilibrium conditions, the adsorption capacity of the resin decreased with increasing temperature and increasing thiourea concentration and increased with increasing gold concentration. This dependence of adsorption capacity on thiourea concentration and temperature may be a useful tool for elution of gold from the loaded resin. Scanning electron microscopy revealed evidence of deposition of elemental gold on the loaded resin under non equilibrium conditions. The proposed mechanism for "adsorption" of gold-thiourea complex onto this cation exchange resin consists of an ion exchange reaction followed by a reduction of the exchanged gold complex to elemental gold on the surface of the resin.

Jan 1, 1997

By S. O. Moshier, L. S. Barron, J. C. Hower

The Hardgrove grindability test, commonly used in coal characterization, was conducted on 13 Mississippian carbonates from Kentucky, Tennessee and Illinois. The results demonstrated that the grindability increases with a decrease in the Si02/(MgCO3+CaCO3) ratio, with fine-grained and petrographically-complex stones having lower grindabilities. Also, the relationship between the Bond work index and Hardgrove grindability is significant.

Jan 1, 1993

By K. Kavouridis

On 30 April 2004, a large scale slope failure incident occurred at the external waste dump facility of the South Field Mine, in the Western Macedonia Lignite Center, Greece. This landslide involved the mobilization of waste overburden material (that was continuously deposited for the last 20 years) in the order of 40 Mm3, while the material that moved outside the boundaries of the waste dump was in the order of 3 Mm3. The factors that led to failure as well as the procedures and measures taken in order to stabilize the failure and resume normal operations at the South Field Mine are presented and discussed. Emphasis is given to the impact on mine operations and the cost related to resuming of normal production operation as well as to implementing important modifications and improvements of the materials handling system.

Jan 1, 2006

By A. Leppala

Scope of the Courier 300 System The fact that reliable on-stream analysis is a prerequisite for effective flotation control is hardly disputed today. Nevertheless, up to now no system has been available that includes all the equipment necessary for successful analysis. However essential an on-stream analyser is in itself, reliable and accurate assaying can only be assured after techniques for sampling, handling the slurries and computing the X-ray data have been developed for the purpose. The Outokumpu Company's Courier 300 System is a complete package that can be installed and handed over with the key. It includes the equipment needed for sampling and handling the slurries. It has been developed from the start to meet industrial demands. Obviously an on-line system must comply with far stricter standards than one designed for a laboratory. Assays are computed by an Outokumpu 316 digital data processor, which is an integral part of the system and controls its entire performance. The computer software is programmed as a standard package, including a highly advanced new model for assay computation. Analysis output is available for a process computer, report typewriter:, and recorders. The package also includes calibration for slurry assays at our pilot installation before delivery. A complete Courier System can analyse up to 4Z slurries and six elements in each slurry. Thanks to its modular design, it can be dimensioned initially to the customer's requirements and is easy to expand later at low cost. Being a mining company itself, Outokumpu has been able to utilize its own long experience in non-ferrous metallurgy - an important factor contributing to the success of the Courier system. History of the project and present installations The first on-stream analyser was installed at Outokumpu'a Pyhasalmi Con¬centrator at the end of 1967, after several years' development. Since then,

Jan 1, 1971