Search Documents

By L. L. Probert

A three-year project focusing on the depth profiling of respirable coal mine dust particles using scanning electron microscopy coupled with energy dispersive x-ray analysis resulted in the development of statistically classified particle-behavior models. The models depict the changing silicon fraction for 5-, 7-, 9-, and 11-keV accelerating voltages, thereby giving a clear indication of the nature of various types of particles. This paper will focus on the results for respirable quartz particles that occur in underground coal mines across the U.S. The relationship between the amount of surface-available quartz and coal seam rank is well established for Pennsylvania

Jan 1, 1994

By Bradford F. Townsend, Robin B. Dill, Richard M. Croswell

Innovative geotechnical construction techniques were used to construct three pedestrian tunnels under a building slab-on-grade to allow utilization of basement space for manufacturing. Tunnels were constructed using mining techniques through granular fill soils less than three feet below on-going sensitive manufacturing operations. Project design consisted of jet grout underpinning of exterior foundation walls and an arch of drilled-in grouted horizontal dowels for soil pre-support to limit ground movements during excavation. Permanent tunnel lining consisted of arched steel rib sets and invert struts supported on precast footings encased in cast-in-place concrete slab and side walls and a gunite arch.

Jan 1, 1993

By Yuanhong Qi, Xun Fu Wang, Tao Fu, Kunkun Cui, Yingyi Zhang, Jie Wang, Junmao Qie

With the sharp decrease of sulfide nickel resources, the nickel laterite is becoming more attractive as nickel oxide, nickel matte, and nickel-iron. This study investigated the mineral phase structure, chemical analysis, thermal properties, and element distribution characteristics of the rotten rock layer deposited in the Southeast Sulawesi Ophiolite Belt. The results show that the nickel laterite deposited in Southeast Sulawesi Island, Indonesia, belongs to the typical high-nickel and low-iron garnierite-type laterite. The concentrations of nickel and iron of the nickel laterite are 1.99 wt% and 17.55 wt%, respectively. The serpentine, olivine, clay, chlorite, hematite, and magnetite are the major minerals, and the pyroxene, actinolite, limonite, and chromite are the minor minerals in the nickel laterite in Southeast Sulawesi, Indonesia. Serpentine and olivine are the main nickel minerals with an average nickel concentration of 3.65 wt% and 1.73 wt%, respectively. The Fe and Ni have homogeneity and symbiosis in the serpentine and olivine, and their concentrations are often positively correlated.

By Dana A. Echter

The Paso Diablo coal project is located in the Guasare Basin in the northwestern region of Venezuela near the border with Colombia. In 1987, Carbones del Guasare SA, a joint venture comprised of Carbozulia and A.A. Antilles Coal (an Arco and AgipCoal joint venture) was formed to develop the Paso Diablo coal reserves for world markets. Regional drilling has indicated a coal resource of more than 6 Gt (6.6 billion st). Further exploration has delineated the Paso Diablo deposit as an area particularly suited for cost-effective surface mining. The calculated economically minable reserves of this area (200 Mt or 220 million st) and the coal quality characteristics are based on extensive core drilling programs. Initial coal mining operations began in August of 1987 and the mine is presently producing at a rate of 1.5 Mt/a (1.65 million stpy). The coal is hauled about 85 km (53 miles) to a barge loading terminal at Santa Cruz de Mara using highway-type haul trucks. When the coal reaches the terminal, it is loaded into barges and then transloaded onto ocean-going vessels with barge mounted

Jan 1, 1990

By P. G. Dempsey, J. R. Heberger, J. P. Pollard

During a mine disaster or emergency, underground air can quickly become contaminated. In these circumstances, all underground mine workers are taught to don breathable air supply units at the first sign of an emergency. However, no contemporary oxygen consumption data is available for the purposes of designing breathing air supply equipment specifically for mine escape. Further, it would be useful to quantify the oxygen requirements of breathing air supply users for various escape scenarios. To address this need, 14 participants crawled a distance of 305 m each while their breath-by-breath oxygen consumption measurements were taken. Using these data, linear regression models were developed to determine peak and average oxygen consumption rates as well as total oxygen consumption. These models can be used by manufacturers of breathing air supply equipment to aid in the design of devices that would be capable of producing sufficient on-demand oxygen to allow miners to perform self-escape.

Jan 1, 2015

By P. Somasundaran, S. Venkatachalam, N. K. Khosla, K. Khosla

Froth flotation of alumina particles was studied by employing and hydrogen gas bubbles. The effect of current density was studied over a range of 0.1 to1.6 kA/m2. Compared to hydrogen, the use of oxygen bubbles at any given gas evolution rate resulted in a higher flotation recovery. The existence of an optimum current density, for each given particle size was indicated. Flotation at higher current densities resulted in better flotation kinetics, while flotation at lower current densities resulted in better Spas utilization.

Jan 1, 1996

By S. K. Kawatra

Outokumpu Electronics has designed a new on-line coal slurry ash analyzer, based on an instrument developed at Michigan Technological University. The primary goal was to build an accurate instrument at the lowest possible cost. The instrument determines ash content from measurements of x-ray backscatter, iron Ka fluorescence, and low-energy y-ray absorption. It is capable of measuring the ash content with a standard error of 1.1% ash over an analysis range of 9-21% ash and 7-22% solids. The analyzer was tested on coals from United States, Poland, Great Britain and the USSR.

Jan 1, 1992

By M. A. Boucher

The purpose of my presentation is threefold: a) to make you aware of what is available in Canada in terms of refractory minerals. b) indicate the mineral deposits that have potential for development. c) show the advantages of Canada as a supplier of electrical energy necessary for the production of electrofused minerals. Canada is a producer of natural refractory minerals, electrofused minerals, and synthetic refractory minerals. Several deposits also have good potential for development. The natural refractory minerals produced in Canada are shown in Table 1. The major minerals by decreasing order of importance in terms of tonnage and values are: dolomite, graphite and magnesite.

Jan 1, 1992

By Steven I. Olson

Since the introduction of froth flotation, the Florida Phosphate Industry has faced the challenge of coarse particle -850 +425µm (-20 +35 Tyler mesh) beneficiation. Several techniques have been used to upgrade this difficult size range. This paper discusses one approach that has met with success; namely, improved fractional recoveries through enhanced areation and improved material transport characteristics via larger than standard flotation cell mechanisms.

Jan 1, 1981

By W. R. Sharp

The ability to target, delineate, excavate, and produce local resources is essential to the establishment of man's long-term presence in space. Many procedures and equipment utilized to mine resources here on Earth may be directly applicable on the lunar surface, while others may need extensive redefinition and development. This paper compares, for a lunar base, the alternative of burrowing into and below the lunar surface with that of surface mining. A conceptual underground mechanical excavator is presented.

Jan 1, 1991

By Avula Rajashekar Yadav, Sreenivasa Rao Islavath

Barrier pillars and gateroads play a vital role for the safe exploitation of coal from the panel in the longwall workings. The barrier pillars and gateroads are subjected to the front abutment and side abutment loads during the retreat of the panel. These structures may fail if the developed load on them is higher than their strength. The stability of the longwall structures such as barrier, gateroads and face is paramount in extracting the coal from the panel safely. For this, a deep longwall mine in India is chosen for the study using a 3D numerical modelling technique. In this paper, three critical conditions such as scenario 1 (no side goaved-out panel), scenario 2 (with side goaved-out panel) and scenario 3 (with two side goaved-out panels) are taken. For each scenario, five retreat distances such as 100, 125, 150, 175 and 200 m are considered for detailed investigation. The development of vertical displacement in gateroads, vertical stresses on barriers, vertical stress concentration factor, abutment zone and yield zone for longwall face are extracted and analyzed. Also, the safety factor of the barrier and longwall face is estimated considering the Hoek–Brown rock mass failure criterion. From the study, it is observed that the maximum vertical displacement of 121 mm in TG3 at scenario 3 for a retreat distance of 200 m and a minimum vertical displacement of 33 mm in TG2 for a retreat distance of 100 m at scenario 2. The development of vertical stress on the barrier is found to be between 8.78 and 13.40 MPa, and the safety factor of the barrier lies in between 1.56 and 1.80. The study also revealed that the yield zone at the longwall face lies within 2 to 3 m.

Dec 29, 2023

By Charles G. Zink

Anthracite is widely known as a domestic or space heating fuel. The prevailing market ratio of domestic to industrial consumption was about 80 to 20 up until 1950. Since then it has been shifting until now the ratio index is about 50/50, exclusive of overseas export. Despite a declining domestic space heating market, the demand for industrial anthracite remains good. However, as a result of stringent air pollution regulations, there is a renewed interest in this low sulphur coal which cannot smoke under any conditions. Anthracite serves other important industries such as power generating, metallurgical, cement, ceramic, chemical, water sewage and industrial wastes filtration. Anthracite is an excellent natural source of carbon and may be utilized in many processes.

Jan 1, 1966

By B. J. Scheiner

The Bureau of Mines, U. S. Department of the Interior, is conducting research on a dewatering technique for fine particles generated during the mineral beneficiation process that will recover a portion of the water now being lost using conventional waste disposal methods and significantly reduce the time required for land reclamation. The technique utilizes a flocculant, polyethylene oxide (PEO), that forms strong stable flocs that can be dewatered rapidly on static and/or rotary screens. In field tests, phosphate clay waste has been dewatered from a nominal 2.5 percent solids to greater than 20 percent solids. In other field tests, coal-clay waste has been dewatered from a nominal 3 percent solids to greater than 55 percent solids, in addition, small-scale continuous tests have shown that bentonitic clays can be dewatered from 12 percent solids to 40 percent solids.

Jan 1, 1983

By Vas P. Srinivasa

This paper examines the role of the heavy media separator in the mineral industry. Procedures used in selecting the separating vessel, developing the process flowsheet, and designing a heavy media circuit are discussed. For comparative purposes, the capital investment and operating costs of different types of operation are included.

Jan 1, 1981

By D. G. Hartley

The major copper loss at Mount Lyell is in the coarsest particles presented to flotation. An analysis of data collected from the five primary and six secondary ball mill circuits showed that grinding was limited by low breakage rates in secondary mills, possibly due to oversize balls. For 5 months, the make-up ball size for one secondary mill was reduced from 50 to 30 mm. Frequent steady-state tests indicated that overall average breakage rates could be increased by about 70% using smaller balls. A mathematical simulation of the whole circuit with increased breakage rates showed that the resultant finer grind was likely to improve copper recoveries by about 22.

Jan 1, 1981

By J. Snowberger III

Rhenium is a valuable and extremely rare chemical element with unique chemical properties. It is extracted commercially as a byproduct from the processing of molybdenite associated with porphyry copper ores. There is a present interest in recovering rhenium from copper pregnant leach solutions (PLS) produced by copper heap and stockpile leaching. These solutions contain rhenium at very dilute concentrations, typically in the 1 mg/L concentration range. This paper describes laboratory column ion exchange experiments to extract rhenium from these solutions using weakly basic anion exchange resins and actual plant PLS from two operating mines. The dynamic loading and elution behavior of Re on Purolite® A170 and A172 is discussed.

Feb 23, 2014

By S. A. Richards

Business planning in the coal' industry revolves around the production and quality forecast. It is difficult to accurately estimate costs and revenues until the production forecast is made. At mines where production comes from multiple sections, quality is tied to each section's production. Blending becomes a part of the planning process. In order to respond to rapidly changing business climate, a reliable program is needed to accurately forecast the effects of changes in key parameters affecting the production. This paper discusses an efficient, intuitive, and economical approach to underground coal mine planning program which uses a PC-based relational database as the programming platform to forecast production and quality. The program was developed at a major coal company. The relational nature of the production planning data, the programming algorithm, and the underlying principles are discussed in this paper.

Jan 1, 1994

By T. Veneroso

Comminution is the process by which rock or ore is reduced to a size where the liberation of the minerals is maximized without changing the chemical or physical properties of the rock. Comminution accounts for about 50% of all energy that mines use (Klein et al., 2018). Growing demands from stakeholders and shareholders for sustainable development and CO2 reduction will increase the need for energy-efficient comminution. Ores with different mineralogical characteristics, textures, strengths, apparent stiffness, and mass-specific fracture energies need to be processed with a specific, new, and efficient comminution technology to increase the production and profitability of mining companies. The adoption of crusher wear parts built with new materials, such as non-Hadfield manganese steel or synthetic materials or traditional manganese with wear-resistant components, could improve the efficiency of the crushers, reduce downtime, increase production, improve the desired P80 (the aperture through which 80% of the product will pass) product size distribution, and enhance mine safety.

Feb 1, 2023

By R. Q. Honaker

Recent research has shown that enhanced gravity separators provide the opportunity to effectively clean I mm x 37 micron coal. At Southern Illinois University, a detailed experimental program was performed on a continuous Falcon Concentrator, which was found to achieve separations at mass throughput capacity values in excess of 100 tonnes/hour. The apparent particle separation density for I mm x 73 micron coal was about 1.60 with relatively high efficiency (Ep = 0.12). Typical ash and sulfur rejection values of 85% and 70%, respectively, were achieved while recovering 85% of the combustible material. Metallurgical and efficiency data from the evaluation are presented in this publication.

Jan 1, 1998

By J. A. Meech

An analysis of screen design options on the operating efficiency of secondary crushing plants has been conducted using a dynamic computer model. The model allows for the simulation of a wide variety of crushing circuits and can be run on either a microcomputer (IBM PC/XT) or a large time-sharing mainframe computer. Size reduction and separation characteristics of crushers and screens are based on standard manufacturer design and performance data. Input/output routines are available in tabular, alarm or strip chart recorder modes to facilitate operation of the program. A number of alternate circuit designs are compared to show the influence of surge capacity, screen size and area, screen deck location, and closed side crusher settings on the operation of a 10,000 ton per day plant. The program is currently in use at Queen's University to teach plant operations and control. It has potential to be a valuable tool for operator training.

Jan 1, 1985